Discrete element modelling of power draw of tumbling mills

The power required to operate large mills is typically 5-10 MW. Hence, optimisation of power consumption will have a significant impact on overall economic performance and environmental impact. Power draw modelling results using the discrete element code PFC3D have been compared with results derived from the widely used empirical Model of Morrell. This is achieved by calculating the power draw for a range of operating conditions for constant mill size and fill factor using two modelling approaches. fThe discrete element modelling results show that, apart from density, selection of the appropriate material damping ratio is critical for the accuracy of modelling of the mill power draw. The relative insensitivity of the power draw to the material stiffness allows selection of moderate stiffness values, which result in acceptable computation time. The results obtained confirm that modelling of the power draw for a vertical slice of the mill, of thickness 20% of the mill length, is a reliable substitute for modelling the full mill. The power draw predictions from PFC3D show good agreement with those obtained using the empirical model. Due to its inherent flexibility, power draw modelling using PFC3D appears to be a viable and attractive alternative to empirical models where necessary code and computer power are available.

Designing a 161-element Ku-band microstrip reflectarray of variable size patches using an equivalent unit cell waveguide approach

An equivalent unit cell waveguide approach (WGA) to designing 4 multilayer microstrip reflectarray of variable size patches is presented. In this approach, a normal incidence of a plane wave on an infinite periodic array of radiating elements is considered to obtain reflection coefficient phase curves for the reflectarray's elements. It is shown that this problem is equivalent to the problem of reflection of the dominant TEM mode in a waveguide with patches interleaved by layers of dielectric. This waveguide problem is solved using a field matching technique and a method of moments (MoM). Based on this solution, a fast computer algorithm is developed to generate reflection coefficient phase curves for a multilayer microstrip patch reflectarray. The validity of the developed algorithm is tested against alternative approaches and Agilent High Frequency Structure Simulator (HFSS). Having confirmed the validity of the WGA approach, a small offset feed two-layer microstrip patch array is designed and developed. This reflectarray is tested experimentally and shows good performance.

Geometric nonlinear analysis of thin plates by a refined nonlinear non-conforming triangular plate element

Based on the refined non-conforming element method for geometric nonlinear analysis, a refined nonlinear non-conforming triangular plate element is constructed using the Total Lagrangian (T.L.) and the Updated Lagrangian (U.L.) approach. The refined nonlinear non-conforming triangular plate element is based on the Allman's triangular plane element with drilling degrees of freedom [1] and the refined non-conforming triangular plate element RT9 [2]. The element is used to analyze the geometric nonlinear behavior of plates and the numerical examples show that the refined non-conforming triangular plate element by the T.L. and U.L. approach can give satisfactory results. The computed results obtained from the T.L. and U.L. approach for the same numerical examples are somewhat different and the reasons for the difference of the computed results are given in detail in this paper. © 2003 Elsevier Science Ltd. All rights reserved.

The application of wave induced forces to a two-dimensional finite element long wave hydrodynamic model

This paper describes the modification of a two-dimensional finite element long wave hydrodynamic model in order to predict the net current and water levels attributable to the influences of waves. Tests examine the effects of the application of wave induced forces, including comparisons to a physical experiment. An example of a real river system is presented with comparisons to measured data, which demonstrate the importance of simulating the combined effects of tides and waves upon hydrodynamic behavior. (C) 2002 Elsevier Science Ltd. All rights reserved.

Desafios da administra????o p??blica brasileira: governan??a, autonomia, neutralidade

O objetivo deste texto ?? iniciar um levantamento da dificuldades impostas ?? reforma administrativa a partir da considera????o do problema da neutralidade da burocracia versus o requisito da autonomia de decis??o, elemento fundamental do Modelo de Administra????o P??blica Gerencial. Tal problema assume especial relev??ncia frente aos objetivos de aumentar a governan??a do Estado e constitui um dos desafios centrais do Plano Diretor da Reforma do Aparelho do Estado, particularmente no que diz respeito ?? forma de administra????o do chamado ???n??cleo estrat??gico??? ??? respons??vel pela defini????o das leis e pol??ticas p??blicas ??? e das ???atividades exclusivas de Estado??? ??? caracterizadas pelo exerc??cio do poder de legislar e tributar, fiscalizando, regulamentando e transferindo recursos. Para isso, a discuss??o est?? organizada em quatro se????es. Na primeira, s??o rapidamente apresentados os conceitos de governabilidade e governan??a, com ??nfase no fato de que a distin????o entre eles representa apenas um recurso anal??tico. Na segunda se????o, a partir das distin????es cl??ssicas de Max Weber entre pol??tica e administra????o, pol??ticos e burocratas, busca-se caracterizar a neutralidade burocr??tica e mostrar que representa, na realidade, apenas um dos elementos de uma constru????o t??pico ideal, cada vez mais distante de qualquer correspond??ncia com o mundo real. Em seguida, comenta-se rapidamente o processo de mudan??a do modelo de administra????o p??blica; e s??o apresentadas algumas das caracter??sticas do chamado Modelo de Administra????o P??blica Gerencial que, em lugar da neutralidade, implicam elevado grau de autonomia por parte dos agentes burocr??ticos. Por fim, s??o tecidas algumas considera????es, procurando mostrar que, da mesma maneira que a neutralidade, a autonomia burocr??tica apresenta dificuldades e que a proposta da ???autonomia imersa??? ou ???autonomia inserida??? exibe implica????es que merecem reflex??o mais demorada.

Potássio : fontes alternativas, tratamentos térmicos e disponibilidade para plantas de milho (Zea Mays L.)

Nosso país é um dos principais produtores agrícolas do mundo e altamente dependente da importação de fertilizantes, principalmente o potássio. Visando reduzir essa dependência, materiais provenientes de rochas para fornecimento desse elemento estão sendo testados. Este estudo foi divido em dois experimentos: um experimento em laboratório e um em casa de vegetação. O experimento em laboratório teve por objetivo avaliar os diferentes tipos de tratamentos térmicos e extratores, associados a fontes alternativas de potássio, no aumento da disponibilidade de K. O ensaio foi realizado num delineamento experimental inteiramente casualizado num esquema fatorial 4 x 5 x 3, com quatro repetições. Os fatores estudados foram: quatro fontes alternativas de potássio (verdete, fonolito, gnaisse e granito); cinco tratamentos térmicos (radiação em forno micro-ondas; autoclavagem; aquecimento em forno mufla com resfriamento rápido; aquecimento em forno mufla com resfriamento lento; e o material in natura); e três extratores: água, ácido cítrico 2 % e solução Mehlich-1. As extrações foram realizadas utilizando 4 g das fontes alternativas, adicionando-se 40 mL de cada extrator, as amostras foram agitadas, centrifugadas, filtradas e avolumadas. Foram realizadas seis extrações sucessivas e determinada a concentração de potássio nos extratos. Os dados obtidos foram submetidos à análise de variância, sendo seus efeitos desdobrados em contrastes ortogonais. O experimento em casa de vegetação teve por objetivo avaliar o efeito da utilização de fontes alternativas de potássio, submetidas a tratamentos térmicos, no fornecimento de potássio para plantas de milho (Zea mays L.). O delineamento experimental adotado foi em blocos casualizados, em um esquema fatorial (3 x 5) + 1, sendo três fontes alternativas de K (verdete, fonolito e granito), submetidas à cinco diferentes tratamentos (aquecimento em forno mufla com resfriamento lento, aquecimento em forno mufla com resfriamento rápido, radiação em forno micro-ondas, autoclavagem, e o material in natura). As fontes alternativas foram comparadas com o cloreto KCl. Amostras de solo contendo 2 dm³ de TFSA, foram incubadas durante 20 dias. Após a adubação, em cada vaso foram aplicadas as fontes alternativas de potássio. Realizou-se o plantio com cinco sementes de milho e posterior desbaste, deixando três plantas por vaso. Decorridos 40 dias da semeadura, foi realizado o corte da parte aérea das plantas, a coleta de amostras de solo para análise dos teores de potássio e separação das raízes. Os dados obtidos foram submetidos à análise de variância e desdobrados em contrastes ortogonais. Observando os resultados obtidos nos experimentos de laboratório e casa de vegetação, podemos concluir que a fonte alternativa e proporcionou melhores resultados e que possui potencial agronômico para ser utilizada como fonte alternativa de potássio foi o fonolito. Utilizando o fonolito como fonte alternativa de nutrientes, o tratamento térmico que proporcionou melhores resultados foi o com aquecimento em forno mufla, principalmente quando o resfriamento foi realizado lentamente.

Estimating Local Part Thickness in Midplane Meshes for Finite Element Analysis

Within the development of motor vehicles, crash safety (e.g. occupant protection, pedestrian protection, low speed damageability), is one of the most important attributes. In order to be able to fulfill the increased requirements in the framework of shorter cycle times and rising pressure to reduce costs, car manufacturers keep intensifying the use of virtual development tools such as those in the domain of Computer Aided Engineering (CAE). For crash simulations, the explicit finite element method (FEM) is applied. The accuracy of the simulation process is highly dependent on the accuracy of the simulation model, including the midplane mesh. One of the roughest approximations typically made is the actual part thickness which, in reality, can vary locally. However, almost always a constant thickness value is defined throughout the entire part due to complexity reasons. On the other hand, for precise fracture analysis within FEM, the correct thickness consideration is one key enabler. Thus, availability of per element thickness information, which does not exist explicitly in the FEM model, can significantly contribute to an improved crash simulation quality, especially regarding fracture prediction. Even though the thickness is not explicitly available from the FEM model, it can be inferred from the original CAD geometric model through geometric calculations. This paper proposes and compares two thickness estimation algorithms based on ray tracing and nearest neighbour 3D range searches. A systematic quantitative analysis of the accuracy of both algorithms is presented, as well as a thorough identification of particular geometric arrangements under which their accuracy can be compared. These results enable the identification of each technique’s weaknesses and hint towards a new, integrated, approach to the problem that linearly combines the estimates produced by each algorithm.

Finite element analysis of pectus carinatum surgical correction via a minimally invasive approach

Pectus carinatum (PC) is a chest deformity caused by a disproportionate growth of the costal cartilages compared to the bony thoracic skeleton, pulling the sternum towards, which leads to its protrusion. There has been a growing interest on using the ‘reversed Nuss’ technique as minimally invasive procedure for PC surgical correction. A corrective bar is introduced between the skin and the thoracic cage and positioned on top of the sternum highest protrusion area for continuous pressure. Then, it is fixed to the ribs and kept implanted for about 2–3 years. The purpose of this work was to (a) assess the stresses distribution on the thoracic cage that arise from the procedure, and (b) investigate the impact of different positioning of the corrective bar along the sternum. The higher stresses were generated on the 4th, 5th and 6th ribs backend, supporting the hypothesis of pectus deformities correction-induced scoliosis. The different bar positioning originated different stresses on the ribs’ backend. The bar position that led to lower stresses generated on the ribs backend was the one that also led to the smallest sternum displacement. However, this may be preferred, as the risk of induced scoliosis is lowered.

New Steel Alloys for the Design of Heat Recovery Steam Generator Components of Combined Cycle Gas Plants

Demand for power is growing every day, mainly due to emerging economies in countries such as China, Russia, India, and Brazil. During the last 50 years steam pressure and temperature in power plants have been continuously raised to improve thermal efficiency. Recent efforts to improve efficiency leads to the development of a new generation of heat recovery steam generator, where the Benson once-through technology is applied to improve the thermal efficiency. The main purpose of this paper is to analyze the mechanical behavior of a high pressure superheater manifold by applying finite element modeling and a finite element analysis with the objective of analyzing stress propagation, leading to the study of damage mechanism, e.g., uniaxial fatigue, uniaxial creep for life prediction. The objective of this paper is also to analyze the mechanical properties of the new high temperature resistant materials in the market such as 2Cr Bainitic steels (T/P23 and T/P24) and also the 9-12Cr Martensitic steels (T/P91, T/P92, E911, and P/T122). For this study the design rules for construction of power boilers to define the geometry of the HPSH manifold were applied.

Sensor element for a metal-insulator-semiconductor camera system (MISCam)

We discuss the operation of a new type of optical sensor (MISCam) based on a metal-insulator-semiconductor (MIS) structure. The operation principle relies on light-induced changes of the band bending and barrier height at the interface between semiconductor and insulator. An image is obtained from the quenching of the ac signal in analogy to the principle of the laser-scanned photodiode (LSP). Lateral resolution depends on the semiconductor material chosen. We have characterised the MIS structures by C-V, I-V, and spectral response measurements testing different types of insulators like a-Si3N4, SiO2, and AlN. The presence of slow interface charges allows for image memory. Colour sensors can be realised by controlling sign and magnitude of the electric fields in the base and the interface region.

Finite element studies of the mechanical behaviour of the diaphragm in normal and pathological cases

The diaphragm is a muscular membrane separating the abdominal and thoracic cavities, and its motion is directly linked to respiration. In this study, using data from a 59-year-old female cadaver obtained from the Visible Human Project, the diaphragm is reconstructed and, from the corresponding solid object, a shell finite element mesh is generated and used in several analyses performed with the ABAQUS 6.7 software. These analyses consider the direction of the muscle fibres and the incompressibility of the tissue. The constitutive model for the isotropic strain energy as well as the passive and active strain energy stored in the fibres is adapted from Humphrey's model for cardiac muscles. Furthermore, numerical results for the diaphragmatic floor under pressure and active contraction in normal and pathological cases are presented.

Construção e desenvolvimento da identidade profissional do educador de infância - percursos no masculino : um estudo de três casos

Dissertação de Mestrado em Supervisão em Educação, enquadrada na linha de investigação sobre Desenvolvimento Profissional dos Professores, apresentada à Escola Superior de Educação de Lisboa

Impact of Sahara dust transport on Cape Verde atmospheric element particles

The objectives of this study were to (1) conduct an elemental characterization of airborne particles sampled in Cape Verde and (2) assess the influence of Sahara desert on local suspended particles. Particulate matter (PM10) was collected in Praia city (14°94'N; 23°49'W) with a low-volume sampler in order to characterize its chemical composition by k0-INAA. The filter samples were first weighed and subsequently irradiated at the Portuguese Research Reactor. Results showed that PM10 concentrations in Cape Verde markedly exceeded the health-based air quality standards defined by the European Union (EU), World Health Organization (WHO), and U.S. Environmental Protection Agency (EPA), in part due to the influence of Sahara dust transport. The PM10 composition was characterized essentially by high concentrations of elements originating from the soil (K, Sm, Co, Fe, Sc, Rb, Cr, Ce, and Ba) and sea (Na), and low concentrations of anthropogenic elements (As, Zn, and Sb). In addition, the high concentrations of PM measured in Cape Verde suggest that health of the population may be less affected compared with other sites where PM10 concentrations are lower but more enriched with toxic elements.