Bismuth germanate films prepared by Pechini method

Bismuth germanate films were prepared by dip coating and spin coating techniques and the dependence of the luminescent properties of the samples on the resin viscosity and deposition technique was investigated. The resin used for the preparation of the films was obtained via Pechini method, employing the precursors Bi(2)O(3) and GeO(2). Citric acid and ethylene glycol were used as chelating and cross-linking agents, respectively. Results from X-ray diffraction and Raman spectroscopy indicated that the films sintered at 700 degrees C for 10 h presented the single crystalline phase Bi(4)Ge(3)O(12). SEM images of the films have shown that homogeneous flat films can be produced by the two techniques investigated. All the samples presented the typical Bi(4)Ge(3)O(12) emission band centred at 505 nm. Films with 3.1 mu m average thickness presented 80% of the luminescence intensity registered for the single crystal at the maximum wavelength. Published by Elsevier B.V.

Utilização da Berberina na Identificação dos Mastócitos do Molusco Anomalocardia brasiliana

Berberine is an alkaloid used as a fluorochrome in the identification of heparin and DNA. Enerback, 1974, described the technique used until today to study granules rich in heparin of vertebrate mast cells. Santos et al., 2003, studied mast cells of the mollusk Anomalocardia brasiliana using biochemical and histological analysis. This work used the fluorescent dye berberine technique to improve characterization of these cells. Mollusk organs (ctenidium and mantle) were processed with routine histological techniques. Tissue sections were treated with berberine 0,02% in redistilled water acidified to pH 4, by the addition of citric acid for 20 minutes. The visualization was made through fluorescence microscopy with ultraviolet region emission. The mast cell fluorescence had a strong yellow color, where cell nuclei appeared more greenish. This result was very similar to the ones reported before. Mast cells are location at the epithelium surface is the same in both organs, mantle and ctenidium. The fluorescence was easily observed in the granules. Therefore, this technique showed to be good and sensitive to study mast cell of invertebrates

Síntese, estudo cinético e análise microestrutural do sistema cério-níquel obtido pelo método pechini

The cerium oxide has a high potential for use in removing pollutants after combustion, removal of organic matter in waste water and the fuel-cell technology. The nickel oxide is an attractive material due to its excellent chemical stability and their optical properties, electrical and magnetic. In this work, CeO2-NiO- systems on molars reasons 1:1(I), 1:2(II) e 1:3(III) metal-citric acid were synthesized using the Pechini method. We used techniques of TG / DTG and ATD to monitor the degradation process of organic matter to the formation of the oxide. By thermogravimetric analysis and applying the dynamic method proposed by Coats-Redfern, it was possible to study the reactions of thermal decomposition in order to propose the possible mechanism by which the reaction takes place, as well as the determination of kinetic parameters as activation energy, Ea, pre-exponential factor and parameters of activation. It was observed that both variables exert a significant influence on the formation of complex polymeric precursor. The model that best fitted the experimental data in the dynamic mode was R3, which consists of nuclear growth, which formed the nuclei grow to a continuous reaction interface, it proposes a spherical symmetry (order 2 / 3). The values of enthalpy of activation of the system showed that the reaction in the state of transition is exothermic. The variables of composition, together with the variable temperature of calcination were studied by different techniques such as XRD, IV and SEM. Also a study was conducted microstructure by the Rietveld method, the calculation routine was developed to run the package program FullProf Suite, and analyzed by pseudo-Voigt function. It was found that the molar ratio of variable metal-citric acid in the system CeO2-NiO (I), (II), (III) has strong influence on the microstructural properties, size of crystallites and microstrain network, and can be used to control these properties

Degradação do PMMA através da reação despolimerização uitlizando catalisadores de óxidos mistos

In this work, mixed oxides were synthesized by two methods: polymeric precursor and gel-combustion. The oxides, Niquelate of Lanthanum, Cobaltate of Lanthanum and Cuprate of Lanthanum were synthesized by the polymeric precursor method, and treated at 300 º C for 2 hours, calcined at 800 º C for 6h in air atmosphere. In gel-combustion method were produced and oxides using urea and citric acid as fuel, forming for each fuel the following oxides Ferrate of Lanthanum, Cobaltato of Lanthanum and Ferrato of Cobalt and Lanthanum, which were submitted to the combustion process assisted by microwave power maximum of 10min. The samples were characterized by: thermogravimetric analysis, X-ray diffraction; fisisorção of N2 (BET method) and scanning electron microscopy. The reactions catalytic of depolymerization of poly (methyl methacrylate), were performed in a reactor of silica, with catalytic and heating system equipped with a data acquisition system and the gas chromatograph. For the catalysts synthesized using the polymeric precursor method, the cuprate of lanthanum was best for the depolymerization of the recycled polymer, obtaining 100% conversion in less time 554 (min), and the pure polymer, was the Niquelate of Lanthanum, with 100% conversion in less time 314 (min). By gel-combustion method using urea as fuel which was the best result obtained Ferrate of Lanthanum for the pure polymer with 100% conversion in less time 657 (min), and the recycled polymer was Cobaltate of Lanthanum with 100 % conversion in less time 779 (min). And using citric acid to obtain the best result for the pure polymer, was Ferrate of Lanthanum with 100% conversion in less time 821 (min and) for the recycled polymer, was Ferrate of Lanthanum with 98.28% conversion in less time 635 (min)

Síntese de pigmentos cerâmicos inorgânicos nanométricos e encapsulados com estrutura core-shell pela rota dos precursores poliméricos

The present work has as objective the development of ceramic pigments based in iron oxides and cobalt through the polymeric precursor method, as well as study their characteristics and properties using methods of physical, chemical, morphological and optical characterizations.In this work was used iron nitrate, and cobalt citrate as precursor and nanometer silica as a matrix. The synthesis was based on dissolving the citric acid as complexing agent, addition of metal oxides, such as chromophores ions and polymerization with ethylene glycol. The powder obtained has undergone pre-ignition, breakdown and thermal treatments at different calcination temperatures (700 °C, 800 °C, 900 °C, 1000 °C and 1100 °C). Thermogravimetric analyzes were performed (BT) and Differential Thermal Analysis (DTA), in order to evaluate the term decomposition of samples, beyond characterization by techniques such as BET, which classified as microporous materials samples calcined at 700 ° C, 800 º C and 900 º C and non-porous when annealed at 1000 ° C and 1100 º C, X-ray diffraction (XRD), which identified the formation of two crystalline phases, the Cobalt Ferrite (CoFe2O4) and Cristobalite (SiO2), Scanning Electron Microscopy (SEM) revealed the formation of agglomerates of particles slightly rounded;and Analysis of Colorimetry, temperature of 700 °C, 800 °C and 900 °C showed a brown color and 1000 °C and 1100 °C violet

Otimização do processo de síntese do aluminato de cobalto via método de polimerização de complexos (MPC) através do planejamento fatorial fracionado

In the ceramics industry are becoming more predominantly inorganic nature pigments. Studies in this area allow you to develop pigments with more advanced properties and qualities to be used in the industrial context. Studies on synthesis and characterization of cobalt aluminate has been widely researched, cobalt aluminate behavior at different temperatures of calcinations, highlighting especially the temperatures of 700, 800 and 900° C that served as a basis in the development of this study, using the method of polymerization of complex (CPM), economic, and this method applied in ceramic pigment synthesis. The procedure was developed from a fractional factorial design 2 (5-2) in order to optimize the process of realization of the cobalt aluminate (CoAl2O4), having as response surfaces the batch analysis data of Uv-vis spectroscopy conducted from the statistic software 7.0, for this were chosen five factors as input variables: citric acid (stoichiometric manner), puff or pyrolysis time (h), temperature (° C), and calcinations (° C/min), at levels determined for this study. By applying statistics in the process of obtaining the CoAl2O4 is possible the study of these factors and which may have greater influence in getting the synthesis. The pigments characterized TG/DSC analyses, and x-ray diffraction (XRD) and scanning electron microscope (SEM/EDS) in order to establish the structural and morphological aspects of pigment CoAl2O4, among the factors studied it were found to statically with increasing calcinations temperature 700°< 800 <900 °C, the bands of Uv-vis decrease with increasing intensity of absorbance and that with increasing time of puff or pyrolysis (h) there is an increase in bands of Uv-vis proportionally, the generated model set for the conditions proposed in this study because the coefficient of determination can explain about 99.9% of the variance (R²), response surfaces generated were satisfactory, so it s possible applicability in the ceramics industry of pigments

Caracterização microestrutural e elétrica de La(FexNi1-x)O3 sintetizado pelo método da gelatina

The present work deals with the synthesis of materials with perovskite structure with the intention of using them as cathodes in fuel cells SOFC type. The perovskite type materials were obtained by chemical synthesis method, using gelatin as the substituent of citric acid and ethylene glycol, and polymerizing acting as chelating agent. The materials were characterized by X-ray diffraction, thermal analysis, spectroscopy Fourier transform infrared, scanning electron microscopy with EDS, surface area determination by the BET method and Term Reduction Program, TPR. The compounds were also characterized by electrical conductivity for the purpose of observing the possible application of this material as a cathode for fuel cells, solid oxide SOFC. The method using gelatin and polymerizing chelating agent for the preparation of materials with the perovskite structure allows the synthesis of crystalline materials and homogeneous. The results demonstrate that the route adopted to obtain materials were effective. The distorted perovskite structure have obtained the type orthorhombic and rhombohedral; important for fuel cell cathodes. The presentation material properties required of a candidate cathode materials for fuel cells. XRD analysis contacted by the distortion of the structures of the synthesized materials. The analyzes show that the electrical conductivity obtained materials have the potential to act as a cell to the cathode of solid oxide fuel, allowing to infer an order of values for the electrical conductivities of perovskites where LaFeO3 < LaNiO3 < LaNi0,5Fe0,5O3. It can be concluded that the activity of these perovskites is due to the presence of structural defects generated that depend on the method of synthesis and the subsequent heat treatment

Síntese de pigmento cerâmico ferrita de cobalto utilizando planejamento experimental

Synthetic inorganic pigments are the most widely used in ceramic applications because they have excellent chemical and thermal stability and also, in general, a lower toxicity to man and to the environment. In the present work, the ceramic black pigment CoFe2O4 was synthesized by the polymerization Complex method (MPC) in order to form a material with good chemical homogeneity. Aiming to optimize the process of getting the pigment through the MPC was used a fractional factorial design 2(5-2), with resolution III. The factors studied in mathematical models were: citric acid concentration, the pyrolysis time, temperature, time and rate of calcination. The response surfaces using the software statistica 7.0. The powders were characterized by thermal analysis (TG/DSC), x-ray diffraction (XRD), scanning electron microscopy (SEM) and spectroscopy in the UV-visible. Based on the results, there was the formation of phase cobalt ferrite (CoFe2O4) with spinel structure. The color of the pigments obtained showed dark shades, from black to gray. The model chosen was appropriate since proved to be adjusted and predictive. Planning also showed that all factors were significant, with a confidence level of 95%

Síntese e caracterização do poli(ácido láctico) para potencial uso em sistemas de liberação controlada de fármacos

With the advances in medicine, life expectancy of the world population has grown considerably in recent decades. Studies have been performed in order to maintain the quality of life through the development of new drugs and new surgical procedures. Biomaterials is an example of the researches to improve quality of life, and its use goes from the reconstruction of tissues and organs affected by diseases or other types of failure, to use in drug delivery system able to prolong the drug in the body and increase its bioavailability. Biopolymers are a class of biomaterials widely targeted by researchers since they have ideal properties for biomedical applications, such as high biocompatibility and biodegradability. Poly (lactic acid) (PLA) is a biopolymer used as a biomaterial and its monomer, lactic acid, is eliminated by the Krebs Cycle (citric acid cycle). It is possible to synthesize PLA through various synthesis routes, however, the direct polycondensation is cheaper due the use of few steps of polymerization. In this work we used experimental design (DOE) to produce PLAs with different molecular weight from the direct polycondensation of lactic acid, with characteristics suitable for use in drug delivery system (DDS). Through the experimental design it was noted that the time of esterification, in the direct polycondensation, is the most important stage to obtain a higher molecular weight. The Fourier Transform Infrared (FTIR) spectrograms obtained were equivalent to the PLAs available in the literature. Results of Differential Scanning Calorimetry (DSC) showed that all PLAs produced are semicrystalline with glass transition temperatures (Tgs) ranging between 36 - 48 °C, and melting temperatures (Tm) ranging from 117 to 130 °C. The PLAs molecular weight characterized from Size Exclusion Chromatography (SEC), varied from 1000 to 11,000 g/mol. PLAs obtained showed a fibrous morphology characterized by Scanning Electron Microscopy (SEM)

Metacromasia para identificação de basófilos sanguíneos em surubim híbrido: contribuição metodológica

Padua S.B. & Ishikawa M.M. [Metachromasia for blood basophils identification in hybrid surubim catfish: methodological contribution]. Metacromasia para identificacao de basofilos sanguineos em surubim hibrido: contribuicao metodologica. Revista Brasileira de Medicina Veterinaria, 33(3):147-150, 2011. Centro de Aquicultura da Unesp/Jaboticabal Rod. Paulo Donato Castellane, s/n Bairro Rural, Jaboticabal, 14884-900, SP. Brasil. E-mail: santiagopadua@live.comDifferent protocols of fixation and hydrolysis of blood smears of hybrid surubim catfish for metachromasia to marking blood basophils were evaluated. For this reason, methanol, acid-alcohol and formalin vapor were tested as fixatives. For hydrolysis of blood smears, HCl, citric acid and 2-Mercaptoethanol + Urea + NaCl solutions was evaluated. After procedures, the blood smears was stained with toluidine blue (0.025%) diluted in McIlvaine buffer (pH 4). The different protocols for fixation and hydrolysis of blood smears for metachromasia influenced the quality of the reaction. Hydrolysis with 2-Mercaptoethanol + Urea + NaCl solutions provided negative results when using methanol and acid-alcohol as fixatives. The fixation with acid-alcohol associated with citric acid hydrolysis provides highest quality reason.

Microenxertia em cultivares de manga

Com a finalidade de se testar a viabilidade do método de microenxertia para produzir mudas de mangueira livres do fungo Fusarium subglutinans, agente causal da malformação, foram realizados experimentos utilizando-se do ápice meristemático da cultivar Tommy Atkins. Retirou-se o ápice meristemático do porta-enxerto e colocou-se o ápice meristemático da cultivar-copa, denominando-se essa metodologia de microenxertia por substituição de ápice meristemático, na qual foram utilizadas as cultivares Coquinho, Espada, Ouro e Ubá como porta-enxertos. O material de propagação utilizado foi retirado de uma planta-matriz da cultivar Tommy Atkins sem sintomas de malformação. Primeiramente, a parte apical dos ramos foi cortada com aproximadamente 3 cm de comprimento. Os meristemas foram colocados em uma solução antioxidante composta de ácido ascórbico, ácido cítrico e L-cisteína, para evitar a oxidação dos compostos fenólicos existentes na manga. Os meristemas apicais foram cortados com comprimento de 2 mm. em seguida, efetuou-se o corte do meristema apical e de folhas do porta-enxerto, colocando-se o meristema apical sobre o corte do porta-enxerto, recobrindo-se com Parafilm®. Demonstrou-se com a técnica de microenxertia a possibilidade de formação de plantas-matrizes, para implantação de jardim clonal em condições de viveiro protegido.

Impact of atmosphere, organic acids, and calcium on quality of fresh-cut 'Kensington' mango

Fresh-cut slices from ripe 'Kensington' mango (Mangifera indica L.) were prepared aseptically and stored under various treatments at 3 degrees C. Treatments included reduced oxygen (2.5%), enhanced carbon dioxide (5-40%), organic acid application, calcium chloride application, and combinations of the above. Symptoms limiting shelf-life were characterised by tissue darkening, development of a 'glassy' appearance, surface desiccation, and loss of firmness. Reduced oxygen (2.5%) was effective at controlling tissue darkening and the development of a 'glassy' appearance, while calcium application (3%) was partly effective at controlling darkening. Calcium chloride however significantly slowed (but did not stop) loss of tissue firmness. Carbon dioxide (5-40%) and citric acid had little positive effect on shelf-life, with both treatments appearing to promote tissue softening. A combination of low oxygen and calcium allowed 'Kensington' slices to be held for at least 15 days at 3 degrees C. (C) 2006 Elsevier B.V All rights reserved.

Response of minimally processed carambola to chemical treatments and low-oxygen atmospheres

Fresh-cut carambola (Averrhoa carambola L.) has limited marketability due to cut-surface browning. The effect of chemical treatments (ascorbic acid, citric acid and Ca-EDTA), controlled atmosphere (0.4-20.3% O-2) and the association of these processes was investigated. Post-cutting dip and low-oxygen atmospheres did not prevent discoloration or improve sensory and physicochemical parameters. However, ascorbic acid (0.5% and 1%) dips reduced polyphenol oxidase (PPO) activity during storage at 4.5 degrees C, with 1% ascorbic acid inducing the lowest activity. Although cut-surface browning of 'Maha' slices was not relevant, carambola slices treated with 1% ascorbic acid in association with 0.4% oxygen did not present significant browning or loss of visual quality for up to 12 days, 3 days longer than low oxygen alone (0.4% O-2), thus, their quality can be significantly improved by combining both treatments. (c) 2007 Elsevier B.V. All rights reserved.

Preservation of minimally processed aurora-1 peaches using additives

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Características dos frutos de cultivares de pessegueiros e nectarineira, no município de Botucatu – SP

The research had as purpose to evaluate the fruits physical-chemical characteristics of peach cultivars (CP-9553 CYN, CP951 C, Tropic Beauty, Cascata 953, Cascata 797, Cascata 587, Precocinho, Conserva 693, Diamante Mejorado, Turmalina e Marli and Sun Blaze nectarine at Botucatu, São Paulo, Brazil region. It were evaluated the fruits fresh matter, longitudinal and transversal diameters, and the crop period. In relation the physical-chemical characteristics of fruits, it was evaluated the texture, the pH, tritatable acid and soluble solids. The results showed significant differences between the cultivars where the fruits fresh matter were 68,6g ('CP-9553 CYN') and 141,35g ('Cascata 953'); the fruits longitudinal diameter were 50,32mm ('Marli') and 72,12mm ('Conserva 693') and the fruits transversal diameter were 50,50mm ('CP-9553 CYN') and 62,90mm ('Cascata 953'). The post-harvest characteristics also had significant differences. The texture had changes at 517,00gf ('Marli') and 168,47gf ('Precocinho'); the soluble solids were 9,73 degrees Brix on Marli cultivar. The pH was about 3,36 on 'Diamante Mejorado' until 4,48 on CP-9553 CYN cultivar and the acidity was 0,96g of citric acid 100g(-1) fruits juice on Tropic Beauty cultivar. The crop period of the cultivars evaluated were the end of September month until 15(th) November month, being the earliest cultivars Tropic Beauty, CP-951 and CP-951 CYN and the latest cultivar were Marli. It was observed that the news cultivars, until in observations, with Cascata 953, Cascata 797 and Cascata 587, showed crops potential at Botucatu/SP region.