Characterisation of grafted supports used for solid-phase synthesis

A series of 'pellicular' type supports were fabricated by direct gamma-radiation-mediated graft polymerisation of styrene onto polypropylene, followed by aminomethylation. Raman spectroscopy was used for measuring the level of penetration of polystyrene graft into polypropylene, and other structural features such as density of graft and depth of functionalisation. The kinetics of the coupling of fluorenylmethylcarbamate (Fmoc)-labelled amino acids, to the aminomethylated polystyrene grafts have been measured by UV absorption followed cleavage of the Fmoc chromophore. The Raman spectroscopy results showed that for this series of experiments the calculated rate coefficient for coupling of Fmoc-labelled amino acids was primarily dependent on graft thickness, but was also influenced by the proportion of polystyrene graft to polypropylene. In general, it was also shown that with increasing loading capacity of support the calculated rate coefficient for amino-acid coupling decreased correspondingly. In addition, a support that had both a high rate coefficient and a high loading capacity was prepared from polypropylene base material with a co-continuous porous structure (high surface area). (C) 2003 Society of Chemical Industry.

Preparation and characterisation of biodegradable starch-based nanocomposite materials

Different formulations of biodegradable starch-polyester blend nanocomposite materials have been film blown on a pilot scale film blowing tower. The physical properties of different films have been examined by thermal and mechanical analysis and X-ray diffraction. The results show that the addition of an organoclay (from 0 to 5 wt%) significantly improves both the processing and tensile properties over the original starch blends. Wide angle X-ray diffraction (WAXD) results indicate that the best results were obtained for 30wt% starch blends, and the level of delamination depends on the ratio of starch to polyester and amount of organoclay added. The crystallisation temperature of the nanocomposite blends is significantly lower than the base blend. This is probably due to the platelets inhibiting order, and hence crystallisation, of the starch and polyester. The mechanical and thermal properties of the blends are also sensitive to the way the clay particles are dispersed. (C) 2003 Society of Chemical Industry.

Hibridizações curriculares nos cotidianos de uma escola de ensino médio: ou sobre a força dos jovens na invenção de uma vida bonita

O texto apresenta os percursos da investigação realizada numa escola pública de ensino médio do município de Santa Teresa, interior do Espírito Santo. Afirma que, nas ações e inventividades cotidianas dos sujeitos praticantes, são tecidos os processos curriculares que dão movimento à pesquisa, considerando esses praticantes como protagonistas das teoriaspráticas curriculares. Problematiza os modos de ser jovem ao discutir os processos de singularização que acontecem nas relações cotidianas, defendendo uma perspectiva teoricoepistemológica que considera os jovens como sujeitos híbridos que habitam entre-lugares culturais, impossibilitando sua localização em identidades idealizadas ou fixas. Aposta nas relações e criações cotidianas, nos movimentos e tessituras dos currículos que se dão em redes coletivas e compartilhadas de saberesfazessentidos, tecidas entre os jovenspraticantes, seus professores e demais habitantes dos cotidianos escolares para além das uniformidades, padronizações e hierarquias das políticas oficiais de currículos. Assume o processo de hibridação que acontece nessas relações, nas discussões ligadas às teoriaspráticas cotidianas e associa a educação e a produção curricular aos processos culturais mais amplos, reconhecendo os limites da criação de uma definição única e precisa de “currículo”. Nesse sentido, defende o fazer curricular como produção de sentidos, argumentando a favor da criação de currículos hibridizados que se constituem em meio a práticas culturais híbridas, onde os movimentos, usos e negociações devem ser considerados nos processos complexos que os constituem, em meio às criações anônimas que se proliferam nos cotidianos. Assume como opção teoricometodologicopolítica as pesquisas com os cotidianos, utilizando narrativastextuaisimagéticas produzidas nos diferentes contextos da pesquisa pelos praticantes. Evidencia, ainda, que a criação da tese se faz no próprio movimento da escrita, num processo de ficção, discutindo questões ligadas às juventudes, à educação profissionalizante, ao ensino médio, aos modos de pesquisa, às relações cotidianas, às redes de singularidades, aos currículos, aos modelos de escola, às magensnarrativas desses processos, entre outras, sem, no entanto, definir os limites desses campos enunciativos, compondo-se, numa mistura intrigante e complexa de sons, gostos, fazeres, dizeres e calares dos percursos de conhecer, compreendendo a maior “marca cotidiana do cotidiano”.

Estudo da Influência do Número de Acidez Total e Teor de Enxofre Total nas Frações Destiladas no Processo de Corrosão em Aços do Tipo AISI 1020 e AISI 316

Os danos causados pelos processos corrosivos em equipamentos presentes nas refinarias de petróleo, durante as destilações, foram descritos inicialmente em 1920. Inúmeras são as referências reportando estudos de processos corrosivos envolvendo tanto os ácidos naftênicos como os compostos sulfurados; em contrapartida, raras são as fontes de estudo envolvendo simultaneamente ambos. Neste trabalho, escolheram-se dois tipos de óleos: um óleo A - com alto teor de enxofre e um petróleo B com elevada acidez. Fez-se então um blend 50/50 em volume obtendo assim o óleo C para verificar a influência tanto da acidez quanto dos teores de enxofre nos processos corrosivos pelos cortes destes óleos. Após a destilação das três amostras, os derivados obtidos foram caracterizados e submetidos aos testes laboratoriais de corrosão. Os cortes do petróleo A apresentaram teores de enxofre e taxas de corrosão crescentes em função do aumento da temperatura final dos derivados, apresentando uma corrosão máxima de 1,66 mm/ano e produtos de corrosão como troilita (FeS) e pirrota (Fe1-xS). As frações de B apresentaram altos valores de NAT na faixa de temperatura de 220-400 °C, enquanto as taxas de corrosão foram de 0,83 mm/ano para esta faixa de temperatura; os produtos de corrosão encontrados foram o óxido de ferro (Fe2O3) e goetite (α-FeOOH). Por fim, os derivados do blend C, apresentaram propriedades intermediárias aos cortes anteriores o que corroborou para taxas de corrosão menores de 0,50 mm/ano até uma temperatura de 300 °C, expondo assim, a eficiência em utilizar a técnica de misturas de petróleos para o refino.

Fiber average size and distribution dependence on the electrospinning parameters of poly(vinylidene fluoride trifluoroethylene)) membranes for biomedical applications

Poly(vinylidene fluoride-trifluoethylene) electrospun membranes were obtained from a blend of dimethylformamide (DMF) and methylethylketone (MEK) solvents. The inclusion of the MEK to the solvent system promotes a faster solvent evaporation allowing complete polymer crystallization during the jet travelling between the tip and the grounded collector. Several processing parameters were systematically changed to study their influence on fiber dimensions. Applied voltage and inner needle diameter do not have large influence on the electrospun fiber average diameter but in the fiber diameter distribution. On the other hand, the increase of the distance between the needle tip to collector results in fibers with larger average diameter. Independently on the processing conditions, all mats are produced in the electroactive phase of the polymer. Further, MC-3T3-E1cell adhesion was not inhibited by the fiber mats preparation, indicating their potential use for biomedical applications.

Influence of electrospinning parameters on Poly(hydroxybutyrate) electrospun membranes fiber size and distribution

Poly(hydroxybutyrate) (PHB) obtained from sugar cane was dissolved in a blend of chloroform and dimethylformamide (DMF) and electrospun at 40 ºC. By adding DMF to the solution, the electrospinning process for the PHB polymer becomes more stable, allowing complete polymer crystallization during the jet travelling between the tip and the grounded collector. The influence of processing parameters on fiber size and distribution was systematically studied. It was observed that an increase of tip inner diameter promotes a decrease of the fiber average size and a broader distribution. On the other hand, an increase of the electric field and flow rate produces an increase of fiber diameter until a maximum of ~2.0 m, but for electric fields higher than 1.5 kV.cm-1, a decrease of the fiber diameter was observed. Polymer crystalline phase seems to be independent of the processing conditions and a crystallinity degree of 53 % was found. Moreover, thermal degradation of the as-spun membrane occurs in single step degradation with activation energy of 91 kJ/mol. Furthermore, MC-3T3-E1 cell adhesion was not inhibited by the fiber mats preparation, indicating their potential use for biomedical applications.

Características físico-químicas de bebidas de café tipo expresso preparadas a partir de blends de café arábica e conilon

Nos últimos anos tem sido crescente a procura por bebidas de café diferenciadas, como o tipo expresso. Nessa bebida, é essencial um alto teor de extrato aquoso para garantir um bom corpo, o que pode ser obtido utilizando-se o café conilon. O Estado do Espírito Santo é o maior produtor nacional de café conilon. Ainda que existam vários estudos sobre a composição físico-química do café brasileiro, pouco se sabe sobre características físico-químicas das bebidas de café expresso obtidas com blends entre o café arábica e o conilon capixaba. Neste trabalho teve-se como objetivo realizar a caracterização físico-química da bebida de café expresso formulada a partir de blends de café arábica e conilon produzido no Espírito Santo (nas proporções de arábica e conilon de 100:0; 80:20; 60:40; 40:20; e 0:100, respectivamente), com diferentes tipos de processamento (natural e descascado). Foram realizadas análises de umidade, pH, acidez titulável total e extrato aquoso. Constatou-se que a utilização de conilon no blend com arábica, nas duas formas de processamento, acarreta em bebidas com maior valor de pH, menor acidez e maior teor de extrato aquoso. Um maior teor de extrato aquoso é interessante para o preparo de café tipo expresso. Sendo assim, os resultados demonstram a viabilidade da utilização do café conilon em blends com arábica no preparo do café tipo expresso, quando se desejam bebidas com maior teor de extrato aquoso.

Ash deposition during the co-firing of bituminous coal with pine sawdust and olive stones in a laboratory furnace

This article describes an experimental study on ash deposition during the co-firing of bituminous coal with pine sawdust and olive stones in a laboratory furnace. The main objective of this study was to relate the ash deposit rates with the type of biomass burned and its thermal percentage in the blend. The thermal percentage of biomass in the blend was varied between 10% and 50% for both sawdust and olive stones. For comparison purposes, tests have also been performed using only coal or only biomass. During the tests, deposits were collected with the aid of an air-cooled deposition probe placed far from the flame region, where the mean gas temperature was around 640 degrees C. A number of deposit samples were subsequently analyzed on a scanning electron microscope equipped with an energy dispersive X-ray detector. Results indicate that blending sawdust with coal decreases the deposition rate as compared with the firing of unblended coal due to both the sawdust low ash content and its low alkalis content. The co-firing of coal and sawdust yields deposits with high levels of silicon and aluminium which indicates the presence of ashes with high fusion temperature and, thus, with less capacity to adhere to the surfaces. In contrast, in the co-firing of coal with olive stones the deposition rate increases as compared with the firing of unblended coal and the deposits produced present high levels of potassium, which tend to increase their stickiness.

Sociological and philosophical aspects of human interaction with technology: advancing concepts

It is not possible to imagine our lives today without technology. From the moment we get up in the morning until the time that we go to bed at night, technology is present in almost every moment, even if we are not aware of it. Some of the most basic activities we need to perform regularly could not be carried out without technology. Sociological and Philosophical Aspects of Human Interaction with Technology: Advancing Concepts presents a careful blend of conceptual, theoretical and applied research in regards to the relationship between technology and humans. This book explores the importance of these interactions, aspects related with trust, communication, data protection, usability concerning organizational change, and e-learning. The advancement of these theories and practices will benefit from this publication as it provides a voice for the users.

Phase diagrams of binary mixtures of patchy colloids with distinct numbers and types of patches: Theempty fluid regime

We investigate the effect of distinct bonding energies on the onset of criticality of low functionality fluid mixtures. We focus on mixtures ofparticles with two and three patches as this includes the mixture where "empty" fluids were originally reported. In addition to the number of patches, thespecies differ in the type of patches or bonding sites. For simplicity, we consider that the patches on each species are identical: one species has threepatches of type A and the other has two patches of type B. We have found a rich phase behavior with closed miscibility gaps, liquid-liquid demixing, and negative azeotropes. Liquid-liquid demixing was found to pre-empt the "empty" fluid regime, of these mixtures, when the AB bonds are weaker than the AA or BB bonds. By contrast, mixtures in this class exhibit "empty" fluid behavior when the AB bonds are stronger than at least one of the other two. Mixtureswith bonding energies epsilon(BB) = epsilon(AB) and epsilon(AA) < epsilon(BB), were found to exhibit an unusual negative azeotrope. (C) 2011 American Institute of Physics. [doi:10.1063/1.3561396]

Demixing instability in coil-rod blends undergoing polycondensation reactions

The authors extend their earlier work on the stability of a reacting binary polymer blend with respect to demixing [D. J. Read, Macromolecules 31, 899 (1998); P. I. C. Teixeira , Macromolecules 33, 387 (2000)] to the case where one of the polymers is rod-like and may order nematically. As before, the authors combine the random phase approximation for the free energy with a Markov chain model for the chemistry to obtain the spinodal as a function of the relevant degrees of reaction. These are then calculated by assuming a simple second-order chemical kinetics. Results are presented, for linear systems, which illustrate the effects of varying the proportion of coils and rods, their relative sizes, and the strength of the nematic interaction between the rods. (c) 2007 American Institute of Physics.

Use of solvent extraction to remediate soils contaminated with hydrocarbons

The main objective of this research is to exploit the possibility of using an ex situ solvent extraction technique for the remediation of soils contaminated with semi-volatile petroleum hydrocarbons. The composition of the organic phase was chosen in order to form a single phase mixture with an aqueous phase and simultaneously not being disturbed (forming stable emulsions) by the soil particles hauling the contaminants. It should also permit a regeneration of the organic solvent phase. As first, we studied the miscibility domain of the chosen ternary systems constituted by ethyl acetate–acetone–water. This system proved to satisfy the previous requirements allowing for the formation of a single liquid phase mixture within a large spectrum of compositions, and also allowing for an intimate contact with the soil. Contaminants in the diesel range within different functional groups were selected: xylene, naphthalene and hexadecane. The analytical control was done by gas chromatography with FID detector. The kinetics of the extractions proved to be fast, leading to equilibrium after 10 min. The effect of the solid–liquid ratio on the extraction efficiency was studied. Lower S/L ratios (1:8, w/v) proved to be more efficient, reaching recoveries in the order of 95%. The option of extraction in multiple contacts did not improve the recovery in relation to a single contact. The solvent can be regenerated by distillation with a loss around 10%. The contaminants are not evaporated and they remain in the non-volatile phase. The global results show that the ex situ solvent extraction is technically a feasible option for the remediation of semi-volatile aromatic, polyaromatic and linear hydrocarbons.

A fusão de dois mundos: convergência do mundo real e digital nas acções de marketing na rede

No passado, as acções publicitárias eram rotuladas como above the line e below the line, referindo-se à dicotomia de pontos de contacto com os públicos-alvo via Meios de Comunicação Social ou via Ponto de Venda. A esta dicotomia de meios e instrumentos, os anos 90 vieram trazer um terceiro ponto de contacto, crescentemente omnipresente e hegemónico, a world wide web ou rede, a que se acedia via computador. As acções de marketing e comunicação passaram então a rotular-se como online e offline, passando, não já a referir-se aos pontos de contacto, mas aos canais pelos quais circulavam as mensagens e acções das marcas. Desde o início deste século, o poder do digital veio crescendo, em software e hardware, em terminais e tecnologias, assistindo-se a uma transferência de esforços de comunicação, da esfera real para a esfera do digital. O deslumbramento pelo digital conquistou mesmo algumas marcas de dimensão mundial que hoje apostam integralmente o seu orçamento nesta forma de marketing, nas suas múltiplas facetas. Contudo, e porque se tem tornado óbvio que os públicos distribuem os seus favores por múltiplos touch points, para maximizar o impacto, assiste-se agora a um fenómeno único, potenciado por novas tecnologias que surgem todos os dias: em estratégias que se podem denominar de all-line, verifica-se a fusão entre dois mundos, mundo real e mundo digital, em múltiplas actividades de marketing que fazem convergir estas duas realidades em plataformas que vão do computador ao tablet, do smartphone à vending machine interactiva, do facebook ao Google maps, da imprensa tradicional ao pinterest. É esta convergência mundo real - mundo digital que abre agora novas oportunidades à comunicação publicitária, potenciando os ingredientes das marcas de sucesso no futuro: sensações (estímulo dos sentidos), intimidade e mistério, num cocktail suportado por uma nova criatividade.

Exploring nature profits: development of novel and potent lipophilic antioxidants based on galloylecinnamic hybrids

Phenolic acids are ubiquitous antioxidants accounting for approximately one third of the phenolic compounds in our diet. Their importance was supported by epidemiological studies that suggest an inverse relationship between dietary intake of phenolic antioxidants and the occurrence of diseases, such as cancer and neurodegenerative disorders. However, until now, most of natural antioxidants have limited therapeutic success a fact that could be related with their limited distribution throughout the body and with the inherent difficulties to attain the target sites. The development of phenolic antioxidants based on a hybrid concept and structurally based on natural hydroxybenzoic (gallic acid) and hydroxycinnamic (caffeic acid) scaffolds seems to be a suitable solution to surpass the mentioned drawbacks. Galloylecinnamic hybrids were synthesized and their antioxidant activity as well as partition coefficients and redox potentials evaluated. The structureepropertyeactivity relationship (SPAR) study revealed the existence of a correlation between the redox potentials and antioxidant activity. The galloylecinnamic acid hybrid stands out as the best antioxidant supplementing the effect of a blend of gallic acid plus caffeic acid endorsing the hypothesis that the whole is greater than the sum of the parts. In addition, some hybrid compounds possess an appropriate lipophilicity allowing their application as chain-breaking antioxidant in biomembranes or other type of lipidic systems. Their predicted ADME properties are also in accordance with the general requirements for drug-like compounds. Accordingly, these phenolic hybrids can be seen as potential antioxidants for tackling the oxidative status linked to the neurodegenerative, inflammatory or cancer processes.

A fractional approach to the Fermi-Pasta-Ulam problem

This paper studies the Fermi-Pasta-Ulam problem having in mind the generalization provided by Fractional Calculus (FC). The study starts by addressing the classical formulation, based on the standard integer order differential calculus and evaluates the time and frequency responses. A first generalization to be investigated consists in the direct replacement of the springs by fractional elements of the dissipative type. It is observed that the responses settle rapidly and no relevant phenomena occur. A second approach consists of replacing the springs by a blend of energy extracting and energy inserting elements of symmetrical fractional order with amplitude modulated by quadratic terms. The numerical results reveal a response close to chaotic behaviour.