Study on the biomass yield of Duckweed (Lemna minor) (L.) in hydroponic cultures containing different concentrations of aquaeous extract of chicken manure

The biomass yields of duck week (Lemna minor(L) was monitored in hydroponic media prepared by variously extracting 0.50, 1.00 and 2.00g of dried chicken manure per liter of city water (tap water) supply. The culture media consisting of aqueous extract of the various manure treatments were made up to 12 liters in all cases with tap water as control. Plastic baths of 25 liters capacity with 0.71 super(m2) surface area were used as culture facility. Each bath was stocked at a density of 30g super(m-2) with fresh weed samples (i.e 21.30g/bath). Maximum yields were obtained at all treatment levels and control on day 3 and based on the highest yield of 0.37gm super(-2)d super(-1) (dry matter) obtained at 1.00gL manure treatment which was however not significantly higher (P>0.05) than the 0.36gm super(-2)d super(-1) (dry matter) at 0.05gl super(-1) media manure content, an average manure level of 0.75l super(-1) was selected and used to determine the operational plant density. Thus fresh weights of 30 to 300gm super(-2) was grown in triplicate at 30g intervals for a period of 3 days. A regression equation of Y=2.6720+0.0021x with a corresponding maximum density or operational plant density of 266gm super(-2) and yield of 0.98gm super(-2), d super(-1) (dry matter) were obtained. Further growth trials were carried out at the operational density and manure levels of 0.50, 0.75, 1.00, 1.25, 1.50, 1.75 and 2.00gl super(-1) media manure concentration giving a significantly higher yield (P<0.05) of 17gm super(-2), d super(-1) (dry matter). This yield was however doubled to between 2.21 and 2.24gm super(-2) d super(-1) (equivalent to 7.96 to 8.06mt.ha-1, Yr-1 dry matter on extrapolation) if 25% and 75% respectively of the total weed cover were harvested daily within the experimental period. The role of some dissolved plant nutrients (DPN) were also discussed

Evaluation of a new fishing pot trap (Lege) in River Rima, north western Nigeria

Based on the findings and diagnostic survey, a new fishing trap, christened Lege trap was designed and fabricated, and the performance evaluated. The 8-valve Lege trap was assessed concurrently with Malian and Ndurutu traps by the fishermen in the study area. The experiment was conducted in a randomized complete block design with one factor each replicated three times. Data collected on fish diversity number, biomass and size were subjected to descriptive statistics and analysis of variance. The results showed that 22 fish species belonging to thirteen families were caught. The prototype (Lege) trap recorded higher species diversity index (0.90) than the Malian (0.50) and Ndurutu (0.50) traps. The Lege trap also accounted for the largest number (55%) and biomass (63%) of fish caught which was significantly (P<0.05) higher than those of the Malian and Nduutu traps were. The mean length (15.03~c5.70cm), weight (60.43~c48.61g) and girth (4.77~c1.65cm) of fishes caught in the Lege trap were also significantly (P0.05) higher than those caught in the other two traps. These results demonstrated better performance of the new trap than the two conventional traps, even though the sizes of some of the fish species caught in all the traps were below those allowed by the Sokoto State Fisheries Edict where the study was conducted. Therefore, since it is desirable to develop conservation-oriented trap at a least cost, it is necessary to research further on the number of valves and mesh size of the new trap

Effects of fermented fluted pumpkin leaf (Telfaria occidentalis) on the growth and nutrient utilization of Clarias (Clarias gariepinus)

Clarias (Clarias gariepinus) (Burshell, 1821) fingerlings were fed isonitrogenous diets (38.9% crude protein) with fermented fluted pumpkin leaves (FFPL) replacing different proportion (0,50,75,100%) of extruded soybean meal (ESM) for 8 weeks. Growth responses at the different substitution levels measured. Increasing FFPL intake resulted in better weight gains and higher specific growth rates (SGR) of 0.29, 0.36 and 0.38% per day respectively. The increase in growth from feeding diets containing 75% and 100% of the ESM replaced with FFPL were significantly higher (P<0.05) than those of other diets. Further more fish tissue protein deposition consistently increased with increasing level of FFPL concentration in their diets. Fish fed diets where whole ESM was replace 100% FFPL gave the best overall response in terms of their weight gain, food conversion ratio, protein efficiency ratio, and specific growth rate. Economic considerations indicate the replacement of ESM with FFPL, which is a cheaper ingredient in feeds for Clarias

Contribution of haematological factors to the distributions and estimation of Eustrongyliides africanus larvae densities in Clarias gariepinus and Clarias anguillaris from Bida floodplain of Nigeria

The contributions of hematological factors to the distribution and estimations of Eustrongylides africanus larvae densities in Clarias gariepinus and C. anguillaris of Bida floodplain of Nigeria were documented for the first time. The hematological factors making the most important contributions to the distributions of E. africanus larvae infections in clarias species are mean corpuscular haemoglobin concentration (MCHC), mean corpuscular haemoglobin (MCH), mean corpuscular volume (MCV) and neutrophils count, in descending order of magnitude; having the manifestations for the months of January, March, September, and December of the year being closely related. Five haematological factors (neutrophils, lymphocytes and eosinophils counts; MCH and MCV) having positive or negative correlation coefficient (r) between 0.50 and 0.85 contributed to the estimated of E.africanus larvae densities in the wild population of Clarias species

Fluctuations in a tokamak plasma

An experimental investigation of low frequency floating potential fluctuations (f ≤ 200 kHz) in a research tokamak plasma using two spatially separated electrostatic probes has been performed. The spectra, correlation length, and the phase velocity of the fluctuations in both the radial and azimuthal direction have been determined. The propagation velocity in the toroidal direction was also measured and was found to be in the direction of electron current flow. The waves traveled azimuthally in the ion diamagnetic drift direction, even after the usual E x B rotation was taken into account. The electron density fluctuations associated with these oscillations were large, δn/n ≃ 0.35 - 0.50.

The spectra were found to have regularly spaced peaks which seemed to be related to specific azimuthal modes (m =1,2,3,...,etc. ) A parametric study was made to determine what effect plasma parameters had on these peaks. During periods of high electron density in the first 2 msec of the plasma lifetime, strong sawtooth type oscillations were observed. These oscillations typically had frequencies of approximately 10 kHz and were also present when large amounts of neutral gas were added during the discharge by a process called "gas puffing."

The results are compared with experimental observations made on other plasma devices with electric and magnetic probes and with microwave and CO₂ laser scattering techniques. (The scattering measurements are complimentary to the probe measurements since, in the former case, the wavelength is fixed by the scattering angle, but the oscillations could not be spatially localized.) The oscillations in the Caltech torus were probably related to a drift-tearing type instability which is thought to play a major role in the anomalous particle and energy flux observed in tokamaks. Comparisons are made between current theory and the experimental results. However, the theory for the observed oscillations is still in a rudimentary stage of development, and it is hoped that the present investigation will stimulate future analytical work.

Análise de metais tóxicos em Sardinella brasiliensis (sardinha) no canal Sernambetiba da Lagoa da Tijuca (Rio de Janeiro/RJ)

Elementos-traço, de fontes naturais ou antropogênicas, são despejados continuamente nos rios, fato que acarreta sérios problemas, devido a sua toxicidade, longa persistência, bioacumulação e biomagnificação na cadeia alimentar. O sistema lagunar Tijuca-Jacarepaguá-Marapendi recebe um enorme aporte de nutrientes e poluentes devido aos impactos antrópicos em seus rios. Este estudo tem como objetivo principal avaliar os níveis de cobre, zinco, chumbo e alumínio em músculo e víscera na espécie Sardinella brasiliensis (sardinha), que habita a saída do Canal de Sernambetiba, Barra da Tijuca, Rio de Janeiro (RJ). Ao total foram analisados 44 indivíduos. O cobre em músculo apresentou uma concentração média de 0,5 0,66 mg/Kg e de 1,3 10,13 mg/Kg em víscera. Os valores de zinco em músculo e víscera foram de 5,2 3,69 mg/Kg e 25,6 48,16 mg/Kg, respectivamente. A concentração de chumbo foi de 2,48 3,09 mg/Kg (músculo) e 25,6 48,16 mg/Kg (víscera), enquanto a concentração de alumínio variou de 1,68 3,67 mg/Kg em músculo e 28,72 26,99 mg/Kg em víscera. Dentre as amostras, 56,8% apresentaram valores acima do limite estabelecido para consumo humano pela legislação brasileira para chumbo. Os elementos-traço apresentaram tendências de acumulação diferentes de acordo com o local (músculo ou víscera). As concentrações dos metais em músculo foram menores do que em vísceras. Os valores encontrados devem servir de alerta para uma contaminação da população de Sardinella brasiliensis que habita a saída do canal de Sernambetiba. Concluiu-se que a concentração de chumbo nos peixes encontrados estão acima dos limites permitidos para o consumo humano, e que a região encontra-se impactada

Quantum Mechanics Studies of Fuel Cell Catalysts and Proton Conducting Ceramics with Validation by Experiment

We carried out quantum mechanics (QM) studies aimed at improving the performance of hydrogen fuel cells. This led to predictions of improved materials, some of which were subsequently validated with experiments by our collaborators.

In part I, the challenge was to find a replacement for the Pt cathode that would lead to improved performance for the Oxygen Reduction Reaction (ORR) while remaining stable under operational conditions and decreasing cost. Our design strategy was to find an alloy with composition Pt3M that would lead to surface segregation such that the top layer would be pure Pt, with the second and subsequent layers richer in M. Under operating conditions we expect the surface to have significant O and/or OH chemisorbed on the surface, and hence we searched for M that would remain segregated under these conditions. Using QM we examined surface segregation for 28 Pt₃M alloys, where M is a transition metal. We found that only Pt₃Os and Pt₃Ir showed significant surface segregation when O and OH are chemisorbed on the catalyst surfaces. This result indicates that Pt₃Os and Pt3Ir favor formation of a Pt-skin surface layer structure that would resist the acidic electrolyte corrosion during fuel cell operation environments. We chose to focus on Os because the phase diagram for Pt-Ir indicated that Pt-Ir could not form a homogeneous alloy at lower temperature. To determine the performance for ORR, we used QM to examine all intermediates, reaction pathways, and reaction barriers involved in the processes for which protons from the anode reactions react with O₂ to form H₂O. These QM calculations used our Poisson-Boltzmann implicit solvation model include the effects of the solvent (water with dielectric constant 78 with pH 7 at 298K). We found that the rate determination step (RDS) was the O_ad hydration reaction (O_ad + H₂O_ad -> OH_ad + OH_ad) in both cases, but that the barrier for pure Pt of 0.50 eV is reduced to 0.48 eV for Pt₃Os, which at 80 degrees C would increase the rate by 218%. We collaborated with the Pu-Wei Wu’s group to carry out experiments, where we found that the dealloying process-treated Pt2Os catalyst showed two-fold higher activity at 25 degrees C than pure Pt and that the alloy had 272% improved stability, validating our theoretical predictions.

We also carried out similar QM studies followed by experimental validation for the Os/Pt core-shell catalyst fabricated by the underpotential deposition (UPD) method. The QM results indicated that the RDS for ORR is a compromise between the OOH formation step (0.37 eV for Pt, 0.23 eV for Pt_2ML/Os core-shell) and H₂O formation steps (0.32 eV for Pt, 0.22 eV for Pt_2ML/Os core-shell). We found that Pt_2ML/Os has the highest activity (compared to pure Pt and to the Pt₃Os alloy) because the 0.37 eV barrier decreases to 0.23 eV. To understand what aspects of the core shell structure lead to this improved performance, we considered the effect on ORR of compressing the alloy slab to the dimensions of pure Pt. However this had little effect, with the same RDS barrier 0.37 eV. This shows that the ligand effect (the electronic structure modification resulting from the Os substrate) plays a more important role than the strain effect, and is responsible for the improved activity of the core- shell catalyst. Experimental materials characterization proves the core-shell feature of our catalyst. The electrochemical experiment for Pt_2ML/Os/C showed 3.5 to 5 times better ORR activity at 0.9V (vs. NHE) in 0.1M HClO₄ solution at 25 degrees C as compared to those of commercially available Pt/C. The excellent correlation between experimental half potential and the OH binding energies and RDS barriers validate the feasibility of predicting catalyst activity using QM calculation and a simple Langmuir–Hinshelwood model.

In part II, we used QM calculations to study methane stream reforming on a Ni-alloy catalyst surfaces for solid oxide fuel cell (SOFC) application. SOFC has wide fuel adaptability but the coking and sulfur poisoning will reduce its stability. Experimental results suggested that the Ni4Fe alloy improves both its activity and stability compared to pure Ni. To understand the atomistic origin of this, we carried out QM calculations on surface segregation and found that the most stable configuration for Ni₄Fe has a Fe atom distribution of (0%, 50%, 25%, 25%, 0%) starting at the bottom layer. We calculated that the binding of C atoms on the Ni4Fe surface is 142.9 Kcal/mol, which is about 10 Kcal/mol weaker compared to the pure Ni surface. This weaker C binding energy is expected to make coke formation less favorable, explaining why Ni₄Fe has better coking resistance. This result confirms the experimental observation. The reaction energy barriers for CHx decomposition and C binding on various alloy surface, Ni₄X (X=Fe, Co, Mn, and Mo), showed Ni₄Fe, Ni₄Co, and Fe₄Mn all have better coking resistance than pure Ni, but that only Ni₄Fe and Fe₄Mn have (slightly) improved activity compared to pure Ni.

In part III, we used QM to examine the proton transport in doped perovskite-ceramics. Here we used a 2x2x2 supercell of perovskite with composition Ba₈X₇M₁(OH)₁O₂₃ where X=Ce or Zr and M=Y, Gd, or Dy. Thus in each case a 4⁺ X is replace by a 3⁺ M plus a proton on one O. Here we predicted the barriers for proton diffusion allowing both includes intra-octahedron and inter-octahedra proton transfer. Without any restriction, we only observed the inter-octahedra proton transfer with similar energy barrier as previous computational work but 0.2 eV higher than experimental result for Y doped zirconate. For one restriction in our calculations is that the O_donor-O_acceptor atoms were kept at fixed distances, we found that the barrier difference between cerates/zirconates with various dopants are only 0.02~0.03 eV. To fully address performance one would need to examine proton transfer at grain boundaries, which will require larger scale ReaxFF reactive dynamics for systems with millions of atoms. The QM calculations used here will be used to train the ReaxFF force field.

Produção de biodiesel pela rota heterogênea empregando catalisadores a base de Zn e Al

Nos últimos anos, a busca por fontes de energia renováveis e o desenvolvimento de novas tecnologias para a produção de biocombustíveis têm sido objeto de intensa investigação. O biodiesel é um combustível biodegradável, derivado de fontes renováveis e é obtido em escala industrial principalmente através da reação de transesterificação de óleos vegetais e/ou gorduras animais com metanol na presença de catalisadores homogêneos, como NaOH. Entretanto, a utilização de catalisadores heterogêneos tem sido sugerida por diversos autores, por apresentar vantagens como a eliminação dos problemas de separação e purificação dos produtos obtidos. No presente trabalho foi investigada a produção de biodiesel a partir da transesterificação do óleo de soja com metanol utilizando óxidos mistos de Zn e Al como catalisadores sólidos básicos. A influência das variáveis: temperatura, concentração de catalisador e relação molar metanol/óleo de soja na produção de biodiesel foi avaliada. Os catalisadores preparados apresentaram predominantemente sítios básicos e foram ativos frente à reação estudada, sendo os resultados mais promissores apresentados pelo óxido misto com relação molar Al/(Al+Zn)=0,50, obtido por tratamento térmico à 450C, que apresentou rendimentos em ésteres metílicos de até 98,5% sob condições específicas. A metodologia da superfície de resposta foi utilizada visando estabelecer as condições ótimas para maximizar o rendimento em ésteres metílicos, tendo sido encontradas a temperatura de 165oC e a concentração de catalisador de 5,8% m/m em relação massa de óleo, no caso da relação molar metanol/óleo de soja limitada em 15. Essa limitação teve como objetivo garantir um processo viável em escala comercial

Influência do exercício físico sobre a massa e o metabolismo ósseo de indivíduos com lesão medular cervical

Indivíduos que permanecem longo tempo em cadeira de rodas apresentam importante perda de massa óssea, principalmente nos membros inferiores, possivelmente agravada pela baixa ingestão de cálcio dietético e pelo inadequado estado nutricional de vitamina D. O exercício físico pode contribuir para a manutenção ou aumento da massa óssea em diferentes populações e nos indivíduos com lesão medular pode contribuir para atenuar a perda de massa óssea. O objetivo do presente estudo foi avaliar a influência da prática regular de exercício físico sobre a adequação da massa óssea, indicadores bioquímicos do metabolismo ósseo e estado nutricional de vitamina D em indivíduos com lesão medular cervical há pelo menos um ano. Em vinte e cinco homens de 19 a 56 anos sendo 15 fisicamente ativos e 10 sedentários, foi realizada análise sérica de cálcio, PTH, 25(OH)D, IGF-1, osteocalcina e NTx. As medidas do conteúdo mineral ósseo, densidade mineral óssea (DMO), massa magra e massa gorda foram realizadas por DXA. A pigmentação da pele (constitutiva e por bronzeamento) foi determinada por colorimetria com o objetivo de investigar sua influência sobre o estado de vitamina D. A ingestão habitual de cálcio foi registrada em um questionário de frequência alimentar direcionado para alimentos fonte. As comparações entre os dois grupos foram realizadas pela aplicação do Teste t de Student exceto para as variáveis ósseas que foram realizadas após ajustes pela massa corporal total, tempo de lesão e ingestão de cálcio utilizando-se análise de co-variância. Associações entre as variáveis estudadas foram avaliadas através de análise de correlação de Pearson. Valores de p<0.05 foram considerados significativos. Não foram observadas diferenças estatisticamente significativas entre os grupos para nenhuma variável óssea com exceção do z-score da DMO da coluna lombar, que foi significativamente maior no grupo de indivíduos sedentários (0,9 1,7 vs -0,7 0,8; p<0,05). No entanto, entre os indivíduos ativos, aqueles que iniciaram a prática de exercício físico com menos tempo decorrido após a lesão apresentaram maior DMO do fêmur (r=-0,60; p<0,05). Nos indivíduos ativos, a freqüência do exercício apresentou associação negativa com a concentração sérica de i-PTH (r = -0,50; p =0,05) e positiva com a concentração de 25(OH)D (r= 0,58; p <0,05). Após ajustes pela massa corporal total e tempo de lesão foram observadas associações positivas entre a ingestão diária de cálcio e z-score da DMO da coluna lombar (r = 0,73 e p <0,01) e DMO do rádio (r = 0,56 e p <0,05). Os resultados do presente estudo apontam para um efeito benéfico do exercício físico sobre a massa óssea e o perfil hormonal relacionado ao metabolismo ósseo. O início da prática regular de exercício físico o quanto antes após a lesão parece contribuir para atenuar a perda de massa óssea nos membros inferiores. Além disso, os resultados deste estudo sugerem uma possível potencialização do efeito osteogênico do exercício físico quando combinado a uma adequada ingestão de cálcio.

Advanced Reaction Systems for Hydrogen Production

[EN] This PhD work started in March 2010 with the support of the University of the Basque Country (UPV/EHU) under the program named “Formación de Personal Investigador” at the Chemical and Environmental Engineering Department in the Faculty of Engineering of Bilbao. The major part of the Thesis work was carried out in the mentioned department, as a member of the Sustainable Process Engineering (SuPrEn) research group. In addition, this PhD Thesis includes the research work developed during a period of 6 months at the Institut für Mikrotechnik Mainz GmbH, IMM, in Germany. During the four years of the Thesis, conventional and microreactor systems were tested for several feedstocks renewable and non-renewable, gases and liquids through several reforming processes in order to produce hydrogen. For this purpose, new catalytic formulations which showed high activity, selectivity and stability were design. As a consequence, the PhD work performed allowed the publication of seven scientific articles in peer-reviewed journals. This PhD Thesis is divided into the following six chapters described below. The opportunity of this work is established on the basis of the transition period needed for moving from a petroleum based energy system to a renewable based new one. Consequently, the present global energy scenario was detailed in Chapter 1, and the role of hydrogen as a real alternative in the future energy system was justified based on several outlooks. Therefore, renewable and non-renewable hydrogen production routes were presented, explaining the corresponding benefits and drawbacks. Then, the raw materials used in this Thesis work were described and the most important issues regarding the processes and the characteristics of the catalytic formulations were explained. The introduction chapter finishes by introducing the concepts of decentralized production and process intensification with the use of microreactors. In addition, a small description of these innovative reaction systems and the benefits that entailed their use were also mentioned. In Chapter 2 the main objectives of this Thesis work are summarized. The development of advanced reaction systems for hydrogen rich mixtures production is the main objective. In addition, the use and comparison between two different reaction systems, (fixed bed reactor (FBR) and microreactor), the processing of renewable raw materials, the development of new, active, selective and stable catalytic formulations, and the optimization of the operating conditions were also established as additional partial objectives. Methane and natural gas (NG) steam reforming experimental results obtained when operated with microreactor and FBR systems are presented in Chapter 3. For these experiments nickel-based (Ni/Al2O3 and Ni/MgO) and noble metal-based (Pd/Al2O3 and Pt/Al2O3) catalysts were prepared by wet impregnation and their catalytic activity was measured at several temperatures, from 973 to 1073 K, different S/C ratios, from 1.0 to 2.0, and atmospheric pressure. The Weight Hourly Space Velocity (WHSV) was maintained constant in order to compare the catalytic activity in both reaction systems. The results obtained showed a better performance of the catalysts operating in microreactors. The Ni/MgO catalyst reached the highest hydrogen production yield at 1073 K and steam-to-carbon ratio (S/C) of 1.5 under Steam methane Reforming (SMR) conditions. In addition, this catalyst also showed good activity and stability under NG reforming at S/C=1.0 and 2.0. The Ni/Al2O3 catalyst also showed high activity and good stability and it was the catalyst reaching the highest methane conversion (72.9 %) and H2out/CH4in ratio (2.4) under SMR conditions at 1073 K and S/C=1.0. However, this catalyst suffered from deactivation when it was tested under NG reforming conditions. Regarding the activity measurements carried out with the noble metal-based catalysts in the microreactor systems, they suffered a very quick deactivation, probably because of the effects attributed to carbon deposition, which was detected by Scanning Electron Microscope (SEM). When the FBR was used no catalytic activity was measured with the catalysts under investigation, probably because they were operated at the same WHSV than the microreactors and these WHSVs were too high for FBR system. In Chapter 4 biogas reforming processes were studied. This chapter starts with an introduction explaining the properties of the biogas and the main production routes. Then, the experimental procedure carried out is detailed giving concrete information about the experimental set-up, defining the parameters measured, specifying the characteristics of the reactors used and describing the characterization techniques utilized. Each following section describes the results obtained from activity testing with the different catalysts prepared, which is subsequently summarized: Section 4.3: Biogas reforming processes using γ-Al2O3 based catalysts The activity results obtained by several Ni-based catalysts and a bimetallic Rh-Ni catalyst supported on magnesia or alumina modified with oxides like CeO2 and ZrO2 are presented in this section. In addition, an alumina-based commercial catalyst was tested in order to compare the activity results measured. Four different biogas reforming processes were studied using a FBR: dry reforming (DR), biogas steam reforming (BSR), biogas oxidative reforming (BOR) and tri-reforming (TR). For the BSR process different steam to carbon ratios (S/C) from 1.0 to 3.0, were tested. In the case of BOR process the oxygen-to-methane (O2/CH4) ratio was varied from 0.125 to 0.50. Finally, for TR processes different S/C ratios from 1.0 to 3.0, and O2/CH4 ratios of 0.25 and 0.50 were studied. Then, the catalysts which achieved high activity and stability were impregnated in a microreactor to explore the viability of process intensification. The operation with microreactors was carried out under the best experimental conditions measured in the FBR. In addition, the physicochemical characterization of the fresh and spent catalysts was carried out by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), N2 physisorption, H2 chemisorption, Temperature Programmed Reduction (TPR), SEM, X-ray Photoelectron Spectroscopy (XPS) and X-ray powder Diffraction (XRD). Operating with the FBR, conversions close to the ones predicted by thermodynamic calculations were obtained by most of the catalysts tested. The Rh-Ni/Ce-Al2O3 catalyst obtained the highest hydrogen production yield in DR. In BSR process, the Ni/Ce-Al2O3 catalyst achieved the best activity results operating at S/C=1.0. In the case of BOR process, the Ni/Ce-Zr-Al2O3 catalyst showed the highest reactants conversion values operating at O2/CH4=0.25. Finally, in the TR process the Rh-Ni/Ce-Al2O3 catalyst obtained the best results operating at S/C=1.0 and O2/CH4=0.25. Therefore, these three catalysts were selected to be coated onto microchannels in order to test its performance under BOR and TR processes conditions. Although the operation using microreactors was carried out under considerably higher WHSV, similar conversions and yields as the ones measured in FBR were measured. Furthermore, attending to other measurements like Turnover Frequency (TOF) and Hydrogen Productivity (PROD), the values calculated for the catalysts tested in microreactors were one order of magnitude higher. Thus, due to the low dispersion degree measured by H2-chemisorption, the Ni/Ce-Al2O3 catalyst reached the highest TOF and PROD values. Section 4.4: Biogas reforming processes using Zeolites L based catalysts In this section three type of L zeolites, with different morphology and size, were synthesized and used as catalyst support. Then, for each type of L zeolite three nickel monometallic and their homologous Rh-Ni bimetallic catalysts were prepared by the wetness impregnation method. These catalysts were tested using the FBR under DR process and different conditions of BSR (S/C ratio of 1.0 and 2.0), BOR (O2/CH4 ratio of 0.25 and 0.50) and TR processes (at S/C=1.0 and O2/CH4=0.25). The characterization of these catalysts was also carried out by using the same techniques mentioned in the previous section. Very high methane and carbon dioxide conversion values were measured for almost all the catalysts under investigation. The experimental results evidenced the better catalytic behavior of the bimetallic catalysts as compared to the monometallic ones. Comparing the catalysts behavior with regards to their morphology, for the BSR process the Disc catalysts were the most active ones at the lowest S/C ratio tested. On the contrary, the Cylindrical (30–60 nm) catalysts were more active under BOR conditions at O2/CH4=0.25 and TR processes. By the contrary, the Cylindrical (1–3 µm) catalysts showed the worst activity results for both processes. Section 4.5: Biogas reforming processes using Na+ and Cs+ doped Zeolites LTL based catalysts A method for the synthesis of Linde Type L (LTL) zeolite under microwave-assisted hydrothermal conditions and its behavior as a support for heterogeneously catalyzed hydrogen production is described in this section. Then, rhodium and nickel-based bimetallic catalysts were prepared in order to be tested by DR process and BOR process at O2/CH4=0.25. Moreover, the characterization of the catalysts under investigation was also carried out. Higher activities were achieved by the catalysts prepared from the non-doped zeolites, Rh-Ni/D and Rh-Ni/N, as compared to the ones supported on Na+ and Cs+ exchanged supports. However, the differences between them were not very significant. In addition, the Na+ and Cs+ incorporation affected mainly to the Disc catalysts. Comparing the results obtained by these catalysts with the ones studied in the section 4.4, in general worst results were achieved under DR conditions and almost the same results when operated under BOR conditions. In Chapter 5 the ethylene glycol (EG) as feed for syngas production by steam reforming (SR) and oxidative steam reforming (OSR) was studied by using microchannel reactors. The product composition was determined at a S/C of 4.0, reaction temperatures between 625°C and 725°C, atmospheric pressure and Volume Hourly Space Velocities (VHSV) between 100 and 300 NL/(gcath). This work was divided in two sections. The first one corresponds to the introduction of the main and most promising EG production routes. Then, the new experimental procedure is detailed and the information about the experimental set-up and the measured parameters is described. The characterization was carried out using the same techniques as for the previous chapter. Then, the next sections correspond to the catalytic activity and catalysts characterization results. Section 5.3: xRh-cm and xRh-np catalysts for ethylene glycol reforming Initially, catalysts with different rhodium loading, from 1.0 to 5.0 wt. %, and supported on α-Al2O3 were prepared by two different preparation methods (conventional impregnation and separate nanoparticle synthesis). Then, the catalysts were compared regarding their measured activity and selectivity, as well as the characterization results obtained before and after the activity tests carried out. The samples prepared by a conventional impregnation method showed generally higher activity compared to catalysts prepared from Rh nanoparticles. By-product formation of species such as acetaldehyde, ethane and ethylene was detected, regardless if oxygen was added to the feed or not. Among the catalysts tested, the 2.5Rh-cm catalyst was considered the best one. Section 5.4: 2.5Rh-cm catalyst support modification with CeO2 and La2O3 In this part of the Chapter 5, the catalyst showing the best performance in the previous section, the 2.5Rh-Al2O3 catalyst, was selected in order to be improved. Therefore, new Rh based catalysts were designed using α-Al2O3 and being modified this support with different contents of CeO2 or La2O3 oxides. All the catalysts containing additives showed complete conversion and selectivities close to the equilibrium in both SR and OSR processes. In addition, for these catalysts the concentrations measured for the C2H4, CH4, CH3CHO and C2H6 by-products were very low. Finally, the 2.5Rh-20Ce catalyst was selected according to its catalytic activity and characterization results in order to run a stability test, which lasted more than 115 hours under stable operation. The last chapter, Chapter 6, summarizes the main conclusions achieved throughout this Thesis work. Although very high reactant conversions and rich hydrogen mixtures were obtained using a fixed bed reaction system, the use of microreactors improves the key issues, heat and mass transfer limitations, through which the reforming reactions are intensified. Therefore, they seem to be a very interesting and promising alternative for process intensification and decentralized production for remote application.

Investigação da microarquitetura óssea através de microtomografia 3D

A microtomografia computadorizada (uCT) é uma técnica de ensaio não destrutivo, frequentemente utilizada no estudo da estrutura interna de ossos, com uma resolução espacial da ordem de mícrons. Neste trabalho, seis pares de amostras ósseas (fêmur de rato) foram estudados através da uCT. Os ensaios foram conduzidos na presença ou não de filtros de alumínio (espessura de 0,25; 0,50 e 0,75 mm), utilizando-se três níveis de resolução (33,3; 15,0 e 9,5 um). Os parâmetros de arquitetura óssea BS (área óssea da amostra), BV (volume ósseo da amostra), TS (área superficial da amostra), TV (volume da amostra), BV/TV (razão entre o volume ósseo e o volume da amostra), BS/BV (razão entre a área óssea da amostra e o volume ósseo da amostra), Tb.N (densidade trabecular), Tb.Th (espaçamento entre as trabéculas), Tb.Sp (separação trabecular), conectividade e anisotropia foram determinados através das análises em duas (2D) e/ou três (3D) dimensões. A comparação entre os valores dos parâmetros obtidos através dessas análises foi realizada através do teste t pareado e da correlação de Pearson. Com base nos resultados, foi possível determinar a influência da resolução da imagem na qualidade dos parâmetros da arquitetura óssea obtidos através das análises 2D e/ou 3D. Os dados mostram que a presença de filtro de alumínio também afeta a qualidade desses parâmetros. Assim, os melhores resultados são obtidos com resolução máxima e filtro de alumínio com espessura de 0,25 ou 0,50 mm.

970nm抽运下Tm^3／Yb^3＋共掺氧氟玻璃的频率上转换发光

稀土离子掺杂的氧氟玻璃是一种新型上转换发光材料。制备了Tm^3／Yb^3＋单掺、共掺的摩尔分数为n（SiO2）-0．30，n（PbF2）-0．50，n=（Al2O3）=0．15，n（AlF3）=（0．049-x），n（TmF3）=y，n（YbF3）=x（x=0，0．001，0．010，0．015，0．020，y=0，0．001）系统氧氟玻璃，研究了其上转换发光特性、分析了其上转换发光机理。研究发现，在970nm抽运光源激发下，Tm^3＋单掺时没有可见光上转换发射；而加入Yb^3＋后产生了强的蓝光（452n

Estudo do efeito magnetocalórico nos compostos da série Gd1-xDyxAl2

Nesta dissertação, foram investigadas as propriedades magnéticas e magnetocalóricas nos compostos intermetálicos de terras-raras Gd1-xDyxAl2 (x = 0, 0.25, 0.50, 0.75 e 1.00) usando abordagens teórica e experimental. Do ponto de vista teórico, a série Gd1-xDyxAl2 foi descrita através de um modelo para o hamiltoniano magnético, incluindo o efeito Zeeman, interação de troca e a anisotropia de campo elétrico cristalino. As entropias da rede e eletrônica foram consideradas nas aproximações de Debye e de gás de elétrons livres, respectivamente. A parte experimental inclui a preparação do material, sua caracterização e medidas das quantidades magnéticas e magnetocalóricas. Os resultados experimentais e os cálculos teóricos da variação adiabática da temperatura (ΔTad) e da variação isotérmica da entropia (ΔS T), sob variações de campo magnético ao longo da direção de fácil magnetização, estão de bom acordo. O efeito da aplicação do campo magnético ao longo de uma direção de difícil magnetização foi estudado e as componentes da magnetização em função da temperatura foram investigadas. Também foi observado que a temperatura de reorientação de spin, TR, diminui quando a intensidade do campo magnético aumenta. Além disso, as concentrações molares ótimas de um material híbrido formado pelos compostos Gd1-xDyxAl2 (x = 0, 0.25, 0.50, 0.75 e 1.00) foram simuladas usando um método numérico de matriz proposto por Smaili e Chahine. O compósito apresenta um bom intervalo de temperatura para um refrigerador magnético de 60 até 170 K.

Estudo do polimorfismo Ser49Gly do gene do receptor beta adrenérgico 1 (β-adr 1) na população do estado do Rio de Janeiro, Brasil estratificada por cor da pele e ancestralidade genômica

As doenças cardiovasculares possuem a maior taxa de óbitos no mundo, e notavelmente nos últimos anos as pesquisas genéticas sobre as mesmas estão baseadas em estudos de associação, no qual o gene suspeito que esteja em maior frequência entre os pacientes passa a ser considerado um possível fator causal. Os polimorfismos genéticos que ocorrem no receptor beta-adrenérgico podem resultar em mudanças significativas na função do receptor, podendo acarretar fisiopatologias. Neste trabalho, o objetivo foi estimar a diversidade e a frequência do polimorfismo Ser49Gly do gene do receptor beta-adrenérgico 1 a partir de uma amostra de 188 indivíduos da população do Estado do Rio de Janeiro. As frequências também foram analisadas a partir da estratificação da amostra por critério fenotípico em função do padrão de cor da pele em (negros e não negros) ou ancestralidade genética em (afrodescendente e não afrodescendente), definida através da informação dos marcadores de ancestralidade Indels e SNP de cromossomo Y, para avaliar se os padrões de ancestralidade ou cor da pele são fundamentais para a diferenciação e distanciamento genético. Fragmentos de interesse foram amplificados por PCR (reação de cadeia de polimerase) com primers específicos para o marcador Ser49Gly e as reações de genotipagem foram realizadas com enzimas de restrição Eco0109I. Os valores da heterozigosidade variaram entre 0,25-0,50 e 0,20-0,41 nos grupos estratificados por ancestralidade e cor da pele, respectivamente. No que diz respeito à análise do equilíbrio de Hardy-Weinberg, não houve um desvio significativo na distribuição do marcador nas amostras gerais do Estado do Rio de Janeiro, ou mesmo nas amostras estratificadas. A distribuição dos alelos na amostra dos 188 indivíduos da população geral do Rio de Janeiro (AC_RJ) mostrou uma frequência de 80,30% e 19,70% para o alelo selvagem e mutado Ser49Gly, respectivamente. A comparação das análises sobre a distribuição das frequências alélicas para este marcador mostrou a ocorrência de diferenças significativas na distribuição das frequências alélicas entre negros e não negros e afrodescendentes e não afrodescendentes. A diferença significativa observada entre os negros e afrodescendentes, foi em menor grau de distanciamento. A informação obtida em relação à ancestralidade foi crucial para a obtenção dos dados sobre o aumento da variável mutada do polimorfismo Ser49Gly nas populações negras e afrodescendentes do Estado Rio de Janeiro. Tal evidência, em combinação com estudos clínicos podem contribuir para uma análise pormenorizada do padrão de susceptibilidade à doença em questão, em falhas do mecanismo deste receptor.

Emissão de CO2 do solo e sua correlação com a rizosfera de diferentes paisagens de áreas mineradas do município de Santo Antônio de Pádua-RJ

Objetivando avaliar o comportamento das emissões de CO2 do solo em áreas mineradas do município de Santo Antônio de Pádua-RJ e sua correlação com a rizosfera, este presente estudo utilizou uma câmara fechada com sensor de infravermelho em três diferentes paisagens, a saber: A-1 (área reflorestada há 10 anos), A-2 (área desmatada) e A-3 (área em processo de recuperação). Em cada área foi instalada três cilindros para efeitos de repetição. O monitoramento foi realizado durante os meses representativos de cada estação do ano de 2013, sendo a análise realizada durante dois dias consecutivos. Concomitantemente as coletas de CO2 foram realizadas coletas de dados de temperatura e umidade do solo, sendo também avaliadas informações pedológicas através das análises de granulometria, porosidade, pH, carbono orgânico e matéria orgânica. Informações meteorológicas e microclimatológicas também foram extraídas através de uma estação meteorológica automática e através de sensores portáteis. Os resultados permitem concluir que existe uma variação sazonal dos fluxos de CO2, havendo uma tendência de máximos de emissão durante o verão e de mínimas durante o inverno, sendo o outono e a primavera marcados por valores medianos. A correlação das áreas entre os dois dias monitoramento indicam que as emissões foram semelhantes ao da análise em dia anterior, apresentando uma correlação significativa a 5% para A-1 e A-2 e de 1% para A-3. A-1 e A-2 apresentaram emissões de CO2 mais homogêneas que A-3, havendo, entretanto, um maior fluxo de CO2 durante o verão para todas as áreas. Os dados de MOS, COS e pH demonstraram não haver uma correlação direta com as emissões de CO2. Os dados de porosidade e densidade, porém, apontam para uma possível correlação com as menores emissões de CO2 em A-3 devido a menor porosidade e maior densidade de seus solos. A temperatura do solo foi a variável que mais se correlacionou com as emissões de CO2, havendo um índice igual a r =0,68 para A-1 e de r =0,74 para A-2, sendo que em A-3 esta correlação não foi significativa. A temperatura do ar demonstrou uma correlação somente na área descampada de A-2. No que se refere à correlação da umidade do solo não houve correlações diretas significativas, sendo que somente houve uma correlação negativa (r=-0,50) significativa a 5% em A-3 com a umidade do ar. O diagnóstico ambiental das áreas de monitoramento revela que estas possuem baixos indicadores de qualidade, sendo afetados também pela escassez hídrica da região durante oito meses do ano. A-1 apresenta os melhores indicadores biológicos, químicos e microclimáticos, seguidos por A-2 e A-3 que apresentam diversas deficiências e problemas em termos de estrutura e atividade biológica dos solos. Neste estudo permite-se concluir que áreas próximas, porém com características distintas podem produzir diferentes padrões de emissão de CO2, dificultando, portanto, estimativas globais de emissão de CO2. Os elementos mais associados às emissões de CO2 parecem estar relacionados à temperatura do solo e do ar, umidade do ar e estrutura do solo, havendo, entretanto, outros fatores que podem estar indiretamente relacionados e que exercem diferentes influências de acordo com o ambiente analisado.