The role of paved surfaces in the Urban Heat Island phenomenon: Assessment of fundamental thermal parameters and finite element analysis for UHI mitigation

Nowadays the environmental issues and the climatic change play fundamental roles in the design of urban spaces. Our cities are growing in size, many times only following immediate needs without a long-term vision. Consequently, the sustainable development has become not only an ethical but also a strategic need: we can no longer afford an uncontrolled urban expansion. One serious effect of the territory industrialisation process is the increase of urban air and surfaces temperatures compared to the outlying rural surroundings. This difference in temperature is what constitutes an urban heat island (UHI). The purpose of this study is to provide a clarification on the role of urban surfacing materials in the thermal dynamics of an urban space, resulting in useful indications and advices in mitigating UHI. With this aim, 4 coloured concrete bricks were tested, measuring their emissivity and building up their heat release curves using infrared thermography. Two emissivity evaluation procedures were carried out and subsequently put in comparison. Samples performances were assessed, and the influence of the colour on the thermal behaviour was investigated. In addition, some external pavements were analysed. Albedo and emissivity parameters were evaluated in order to understand their thermal behaviour in different conditions. Surfaces temperatures were recorded in a one-day measurements campaign. ENVI-met software was used to simulate how the tested materials would behave in two typical urban scenarios: a urban canyon and a urban heat basin. Improvements they can carry to the urban microclimate were investigated. Emissivities obtained for the bricks ranged between 0.92 and 0.97, suggesting a limited influence of the colour on this parameter. Nonetheless, white concrete brick showed the best thermal performance, whilst the black one the worst; red and yellow ones performed pretty identical intermediate trends. De facto, colours affected the overall thermal behaviour. Emissivity parameter was measured in the outdoor work, getting (as expected) high values for the asphalts. Albedo measurements, conducted with a sunshine pyranometer, proved the improving effect given by the yellow paint in terms of solar reflection, and the bad influence of haze on the measurement accuracy. ENVI-met simulations gave a demonstration on the effectiveness in thermal improving of some tested materials. In particular, results showed good performances for white bricks and granite in the heat basin scenario, and painted concrete and macadam in the urban canyon scenario. These materials can be considered valuable solutions in UHI mitigation.

The influence of infill walls on seismic behavior of a historical building in Shanghai

Seismic assessment and seismic strengthening are the key issues need to be figured out during the process of protection and reusing of historical buildings. In this thesis the seismic behaviors of the hinged steel structure, a typical structure of historical buildings, i.e. hinged steel frames in Shanghai, China, were studied based on experimental investigations and theoretic analysis. How the non-structural members worked with the steel frames was analyzed thoroughly. Firstly, two 1/4 scale hinged steel frames were constructed based on the structural system of Bund 18, a historical building in Shanghai: M1 model without infill walls, M2 model with infill walls, and tested under the horizontal cyclic loads to investigate their seismic behavior. The Shaking Table Test and its results indicated that the seismic behavior of the hinged steel frames could be improved significantly with the help of non-structural members, i.e., surrounding elements outside the hinged steel frames and infilled walls. To specify, the columns are covered with bricks, they consist of I shape formed steel sections and steel plates, which are clenched together. The steel beams are connected to the steel column by steel angle, thus the structure should be considered as a hinged frame. And the infilled wall acted as a compression diagonal strut to withstand the horizontal load, therefore, the seismic capacity and stiffness of the hinged steel frames with infilled walls could be estimated by using the equivalent compression diagonal strut model. A SAP model has been constructed with the objective to perform a dynamic nonlinear analysis. The obtained results were compared with the results obtained from Shaking Table Test. The Test Results have validated that the influence of infill walls on seismic behavior can be estimated by using the equivalent diagonal strut model.

The CONSORT Statement: Application within and adaptations for orthodontic trials

High-quality randomized controlled trials (RCTs) are an integral part of evidence-based medicine. RCTs are the bricks and mortar of high-quality systematic reviews, which are important determinants of health care policy and clinical practice. For published research to be used most effectively, investigators and authors should follow the guidelines for accurate and transparent reporting of RCTs. The consolidated standards of reporting trials (CONSORT) statement and its extensions are among the most widely used reporting guidelines in biomedical research. CONSORT was adopted by the American Journal of Orthodontics and Dentofacial Orthopedics in 2004. Since 2011, this Journal has been actively implementing compliance with the CONSORT reporting guidelines. The objective of this explanatory article is to highlight the relevance and implications of the various CONSORT items to help authors to achieve CONSORT compliance in their research submissions of RCTs to this and other orthodontic journals.

Transformaciones habitacionales en la Región Metropolitana de Buenos Aires : El pasaje del neoliberalismo al neodesarrollismo urbano

La recuperación de la economía argentina luego de la crisis del 2001/02 implicó una importante mejora de múltiples indicadores sociales y económicos, dada entre otros factores, la orientación de políticas públicas tendiente a recuperar el tejido productivo y el empleo. En este contexto, el tándem construcción-obra pública se transformó en un tema central de la agenda y la expansión inmobiliaria fue bien recibida desde la mirada macroeconómica. Sin embargo, este proceso no estuvo exento de contradicciones, y se observan en la región metropolitana un conjunto de tendencias concurrentes producto de la hibridación entre el neoliberalismo urbano aún vigente y la difusión del neodesarrollismo urbano. De allí que la ampliación de acciones de desmercatilización estatal del consumo de bienes y servicios orientados a la reproducción social coexiste con la persistencia del proceso de desmercatilización social regresivo de la producción del espacio habitacional, junto a la intensa mercantilización del espacio construido asociada a la creciente financierización de los ladrillos

Transformaciones habitacionales en la Región Metropolitana de Buenos Aires : El pasaje del neoliberalismo al neodesarrollismo urbano

La recuperación de la economía argentina luego de la crisis del 2001/02 implicó una importante mejora de múltiples indicadores sociales y económicos, dada entre otros factores, la orientación de políticas públicas tendiente a recuperar el tejido productivo y el empleo. En este contexto, el tándem construcción-obra pública se transformó en un tema central de la agenda y la expansión inmobiliaria fue bien recibida desde la mirada macroeconómica. Sin embargo, este proceso no estuvo exento de contradicciones, y se observan en la región metropolitana un conjunto de tendencias concurrentes producto de la hibridación entre el neoliberalismo urbano aún vigente y la difusión del neodesarrollismo urbano. De allí que la ampliación de acciones de desmercatilización estatal del consumo de bienes y servicios orientados a la reproducción social coexiste con la persistencia del proceso de desmercatilización social regresivo de la producción del espacio habitacional, junto a la intensa mercantilización del espacio construido asociada a la creciente financierización de los ladrillos

Transformaciones habitacionales en la Región Metropolitana de Buenos Aires : El pasaje del neoliberalismo al neodesarrollismo urbano

La recuperación de la economía argentina luego de la crisis del 2001/02 implicó una importante mejora de múltiples indicadores sociales y económicos, dada entre otros factores, la orientación de políticas públicas tendiente a recuperar el tejido productivo y el empleo. En este contexto, el tándem construcción-obra pública se transformó en un tema central de la agenda y la expansión inmobiliaria fue bien recibida desde la mirada macroeconómica. Sin embargo, este proceso no estuvo exento de contradicciones, y se observan en la región metropolitana un conjunto de tendencias concurrentes producto de la hibridación entre el neoliberalismo urbano aún vigente y la difusión del neodesarrollismo urbano. De allí que la ampliación de acciones de desmercatilización estatal del consumo de bienes y servicios orientados a la reproducción social coexiste con la persistencia del proceso de desmercatilización social regresivo de la producción del espacio habitacional, junto a la intensa mercantilización del espacio construido asociada a la creciente financierización de los ladrillos

Transformaciones habitacionales en la Región Metropolitana de Buenos Aires : El pasaje del neoliberalismo al neodesarrollismo urbano

La recuperación de la economía argentina luego de la crisis del 2001/02 implicó una importante mejora de múltiples indicadores sociales y económicos, dada entre otros factores, la orientación de políticas públicas tendiente a recuperar el tejido productivo y el empleo. En este contexto, el tándem construcción-obra pública se transformó en un tema central de la agenda y la expansión inmobiliaria fue bien recibida desde la mirada macroeconómica. Sin embargo, este proceso no estuvo exento de contradicciones, y se observan en la región metropolitana un conjunto de tendencias concurrentes producto de la hibridación entre el neoliberalismo urbano aún vigente y la difusión del neodesarrollismo urbano. De allí que la ampliación de acciones de desmercatilización estatal del consumo de bienes y servicios orientados a la reproducción social coexiste con la persistencia del proceso de desmercatilización social regresivo de la producción del espacio habitacional, junto a la intensa mercantilización del espacio construido asociada a la creciente financierización de los ladrillos

Recovery of traditional mortars in the laboratory of materials at the school of architectura of Madrid

The Laboratory of Materials seminar is an optional course offered to students in the School of Architecture in Madrid. It is taught during 35 class hours in the laboratory of materials distributed in two hours and forty minutes weekly. One of the working lines is the preparation of traditional mortars made by students groups, each one of 4 or 5 members. It is basically a practical course, and students have to prepare a group of tests pieces in order to confirm the initial hypothesis, or when needed, make innovations. The test pieces are of 150mmx150mmx10mm and applied to big size hollow bricks, prismatic test pieces of 40mmx40mmx160mm to apply physical and mechanical tests and brick wallings of varied dimensions.

Wedges and plate-bandes: mechanical theories after De la Hire

Plate-bandes are straight masonry arches (they are called, also, flat arches or lintel arches). Ideally they have the surfaces of extrados and intrados plane and horizontal. The stones or bricks have radial joints converging usually in one centre. The voussoirs have the form of wedges and in French they are called "claveaux". A plate-bande is, in fact, a lintel made of several stones and the proportions of lintels and plate-bandes are similar. Proportions of plate-bandes, that is the relationship between the thickness t and the span s (t/s)varies, typically between 1/4–1/3 in thick plate-bandes, and is less than 1/20 in the most slender ones. A ratio of circa 1/8 was usual in the 18th Century and follows a simple geometrical rule: the centre form with the intrados an equilateral triangle and the plate-bande should contain an arc of circle. The joints are usually plane, but in some cases present a «rebated» or «stepped» form. Plate-bandes exert an inclined thrust as any masonry arch. This thrust is usually very high and it requires either massive buttresses, or to be built in the middle of thick walls. Master builders and architects have tried since antiquity to calculate the abutment necessary for any arch. A modern architect or engineer will measure the arch thrust in units of force, kN or tons. Traditionally, the thrust has been measured as the size of the buttresses to resist it safely. Old structural rules, then, addressed the design problem establishing a relationship between the span and the depth of the buttress. These were empirical rules, particular for every type of arch or structure in every epoch. Thus, the typical gothic buttress is 1/4 of the vault span, but a Renaissance or baroque barrel vault will need more than 1/3 of the span. A plate-bande would require more than one half of the span; this is precisely the rule cited by the French engineer Gautier, who tried unsuccessfully to justify it by static reasons. They were used, typically, to form the lintels of windows or doors (1-2 m, typically); in Antiquity they were used, also, though rarely, at the gates of city walls or in niches (ca. 2 m, reaching 5.2 m). Plate-bandes may show particular problems: it is not unusual that some sliding of the voussoirs can be observed, particularly in thick plate-bandes. The stepped joints on Fig. 1, left, were used to avoid this problem. There are other «hidden» methods, like iron cramps or the use of stone wedges, etc. In seismic zones these devices were usual. Another problem relates to the deformation; a slight yielding of the abutments, or even the compression of the mortar joints, may lead to some cracking and the descent of the central keystone. Even a tiny descent will convert the original straight line of the intrados in a broken line with a visible «kink» or angle in the middle. Of course, both problems should be avoided. Finally, the wedge form of the voussoirs lead to acute angles in the stones and this can produce partial fractures; this occurs usually at the inferior border of the springers at the abutments. It follows, that to build a successful plate-bande is not an easy matter. Also, the structural study of plate-bandes is far from simple, and mechanics and geometry are related in a particular way. In the present paper we will concentrate on the structural aspects and their constructive consequences, with a historical approach. We will outline the development of structural analysis of plate-bandes from ca. 1700 until today. This brief history has a more than purely academic interest. Different approaches and theories pointed to particular problem, and though the solution given may have been incorrect, the question posed was often pertinent. The paper ends with the application of modern Limit Analysis of Masonry Structures, developed mainly by professor Heyman in the last fifty years. The work aims, also, to give some clues for the actual architect and engineer involved in the analysis or restoration of masonry buildings.

Energy Analysis of Bare Electrodynamic Tethers

The design of an electrodynamic tether is a complex task that involves the control of dynamic instabilities, optimization of the generated power (or the descent time in deorbiting missions), and minimization of the tether mass. The electrodynamic forces on an electrodynamic tether are responsible for variations in the mechanical energy of the tethered system and can also drive the system to dynamic instability. Energy sources and sinks in this system include the following: 1) ionospheric impedance, 2) the potential drop at the cathodic contactor, 3) ohmic losses in the tether, 4) the corotational plasma electric field, and 5) generated power and/or 6) input power. The analysis of each of these energy components, or bricks, establishes parameters that are useful tools for tether design. In this study, the nondimensional parameters that govern the orbital energy variation, dynamic instability, and power generation were characterized, and their mutual interdependence was established. A space-debris mitigation mission was taken as an example of this approach for the assessment of tether performance. Numerical simulations using a dumbbell model for tether dynamics, the International Geomagnetic Reference Field for the geomagnetic field, and the International Reference Ionosphere for the ionosphere were performed to test the analytical approach. The results obtained herein stress the close relationships that exist among the velocity of descent, dynamic stability, and generated power. An optimal tether design requires a detailed tradeoff among these performances in a real-world scenario.

Caracterización físico-mecánica del yeso de construcción con adición de residuos de poliestireno extruído y residuos cerámicos

Este trabajo estudia el comportamiento de una matriz de yeso de construcción a la que se le han añadido residuos de construcción y demolición (RCD), residuos de poliestireno extruido (XPS) y residuos cerámicos respectivamente, combinados y en diferentes porcentajes en función del peso del yeso. Los residuos de XPS son producto de una obra en Madrid donde el material fue utilizado como aislamiento térmico y los residuos cerámicos corresponden a trozos de ladrillos toscos encontrados en una obra paralizada en la ciudad de Ávila. Se confeccionaron probetas con porcentajes hasta 3% de XPS y hasta 50% de cerámicos en función del peso del yeso utilizado, como referencia se confeccionaron probetas sin adición de RCD. Fueron ensayadas en laboratorio y se determinaron las características físicas y mecánicas de las mismas. Tras un análisis comparativo se evidencian que la adición de residuos de XPS y residuos cerámicos en conjunto disminuye la densidad seca del material y la absorción de agua por capilaridad, en algunos casos disminuye la conductividad térmica y aumenta la dureza superficial. ABSTRACT: This paper studies the behavior of a building gypsum matrix to which have been added Construction and Demolition waste (CDW), residues of extruded polystyrene (XPS) and ceramic waste respectively, and combined in different percentages depending on the weight of gypsum. XPS waste are the product of a work in Madrid where the material was used as thermal insulation and ceramic waste correspond to pieces of rough bricks found in a paralyzed work in the city of Avila. Specimens were prepared with percentages up to 3% of XPS and up to 50% depending on the weight ceramic gypsum used as reference samples were prepared without addition of CDW. They were tested in laboratory and determined the physical and mechanical characteristics thereof. After a comparative analysis they show that the addition of ceramic waste and waste XPS decreases together dry material density and water absorption by capillary action, in some cases the thermal conductivity decreases and increases surface hardness.

Comportamiento térmico y mecánico del yeso con adiciones de aerogel de sílice granulado

La presente tesis doctoral aborda el estudio de un nuevo material mineral, compuesto principalmente por una matriz de yeso (proveniente de un conglomerante industrial basado en sulfato de calcio multifase) y partículas de aerogel de sílice hidrófugo mesoporoso, compatibilizadas mediante un surfactante polimérico, debido a su alto carácter hidrófugo. La investigación se centra en conocer los factores que influyen en las propiedades mecánicas y conductividad térmica del material compuesto generado. Este estudio pretende contribuir al conocimiento sobre el desarrollo de nuevos morteros de elevado aislamiento térmico que puedan ser utilizados en la rehabilitación energética de edificios de viviendas existentes, debido a que estos representan gran parte del consumo energético del parque de viviendas de España, aunque también a nivel internacional. De los materiales utilizados para desarrollar los morteros estudiados, el yeso, además de ser un material muy abundante, especialmente en España, requiere una menor cantidad de energía para la fabricación de un conglomerante (debido a una menor temperatura de fabricación), en comparación con el cemento o la cal, por lo que presenta una menor huella de carbono que estos últimos. Por otro lado, el aerogel de sílice hidrófugo mesoporoso es, de acuerdo con la documentación disponible, el material que posee actualmente la mayor capacidad de aislamiento térmico en el mercado. El desarrollo de nuevos morteros minerales con una capacidad de aislamiento térmico mayor que los materiales aislantes utilizados tradicionalmente, tiene una aplicación relevante en los casos de rehabilitación energética de edificios históricos y patrimoniales, en los que se requiere la aplicación del aislamiento por el interior de la fachada, ya que este tipo de soluciones tienen el inconveniente de reducir el espacio habitable de las áreas involucradas, especialmente en zonas climáticas en las que el aislamiento térmico puede suponer un espesor considerable, por lo que es ideal utilizar materiales de altas prestaciones de aislamiento térmico capaces de aportar el mismo nivel de aislamiento (o incluso mayor), pero en un espesor considerablemente menor. La investigación se desarrolla en tres etapas: bibliográfica, experimental y de simulación. La primera etapa, parte del estudio de la bibliografía existente, relacionada con materiales aislantes, incluyendo soluciones basadas, tanto en morteros aislantes, como en paneles de aislamiento térmico. La segunda, de carácter experimental, se centra en estudiar la influencia de la microestrucrura y macroestructura, del nuevo material mineral, en las propiedades físicas elementales, mecánicas y conductividad térmica del compuesto. La tercera etapa, mediante una simulación del consumo energético, consiste en cuantificar teóricamente el potencial ahorro energético que puede aportar este material en un caso de rehabilitación energética en particular. La investigación experimental se centró principalmente en conocer los factores principales que influyen en las propiedades mecánicas y conductividad térmica de los materiales compuestos minerales desarrollados en esta tesis. Para ello, se llevó a cabo una caracterización de los materiales de estudio, así como el desarrollo de distintas muestras de ensayo, de tal forma que se pudo estudiar, tanto la hidratación del yeso en los compuestos, como su posterior microestructura y macroestructura, aspectos fundamentales para el entendimiento de las propiedades mecánicas y conductividad térmica del compuesto aislante. De este modo, se pudieron conocer y cuantificar, los factores que influyen en las propiedades estudiadas, aportando una base de conocimiento y entendimiento de este tipo de compuestos minerales con aerogel de sílice hidrófugo, no existiendo estudios publicados hasta el momento de finalización de esta tesis, con la aproximación al material propuesta en este estudio, ni con yeso (basado en sulfato de calcio multifase), ni con otro tipo de conglomerantes. Particularmente, se determinó la influencia que tiene la incorporación de partículas de aerogel de sílice hidrófugo, en grandes proporciones en volumen, en un compuesto mineral basado en distintas fases de sulfato de calcio. No obstante, para llevar a cabo las mezclas, fue necesario utilizar un surfactante para compatibilizar este tipo de partículas, con el conglomerante basado en agua. El uso de este tipo de aditivos tiene una influencia, no solo en el aerogel, sino en las propiedades del compuesto en general, dependiendo de su concentración, por lo que se establecieron dos porcentajes de adición: la primera, determinada a partir de la cantidad mínima necesaria para compatibilizar las mezclas (0,1% del agua de amasado), y la segunda, como límite superior, la concentración utilizada habitualmente a nivel industrial para estabilizar burbujas de aire en hormigones espumados (5%). El surfactante utilizado mostró la capacidad de modificar la superficie del aerogel, cambiando el comportamiento de las partículas frente al agua, permitiendo una invasión parcial de su estructura porosa, por parte del agua de amasado. Este comportamiento supone un aumento muy importante en la relación agua/yeso, afectando el hábito cristalino e influenciando negativamente las propiedades mecánicas de la matriz de yeso, presentando un efecto aún notable a mayor concentración de surfactante (5%). En cuanto a las propiedades finales alcanzadas, fue posible lograr un compuesto mineral ultraligero (200 kg/m3), con alrededor de un 60% de aerogel en volumen y de alta capacidad aislante (0,028 W/m•K), presentando una conductividad térmica notablemente menor que los morteros aislantes del mercado, e incluso también menor que la de los aislantes tradicionales basado en las lanas minerales o EPS; no obstante, con la limitante de presentar bajas propiedades mecánicas, condicionando su posible aplicación futura. Entre los factores principales relacionados con las propiedades mecánicas, se encontró que estas dependen exponencialmente del volumen de yeso en el compuesto; no obstante, factores de segundo orden, como el grado de hidratación, o una mejor distribución del conglomerante entre las partículas de aerogel, debido al aumento de la superficie específica del polvo mineral, pueden aumentar las propiedades mecánicas entre el doble y el triple, dependiendo del volumen de aerogel en cuestión. Además, se encontró que el aerogel, en conjunto con el surfactante, es capaz de introducir una gran cantidad de aire (0,70 m3 por cada m3 de aerogel), que unido al agua evaporada (no consumida por el conglomerante durante la hidratación), el volumen de aire total alcanza, generalmente, un 40%, independientemente de la cantidad de aerogel en la mezcla. De este modo, el aire introducido en la matriz desplaza las proporciones en volumen del aerogel y del yeso, disminuyendo, tanto las propiedades mecánicas, como la capacidad aislante de compuesto mineral. Por otro lado, la conductividad térmica mostró tener una dependencia directa de la contribución de las tres fases principales en el compuesto: yeso, aerogel y aire ocluido. De este modo, se pudo desarrollar un modelo matemático, adaptado de uno existente, capaz de calcular, con bastante precisión, la relación de los tres componentes mencionados, en la conductividad térmica de los compuestos, para el rango de volúmenes y materiales utilizados en esta tesis. Finalmente, la simulación del consumo energético realizada a una vivienda típica de España, de los años 1900 a 1959 (basada en muros de ladrillo macizo), para las zonas climáticas estudiadas (A, D y E), permitió observar el potencial ahorro energético que puede aportar este material, dependiendo de su espesor, como aislamiento interior de los muros de fachada. Particularmente, para la zona A, se determinó un espesor óptimo de 1 cm, mientras que para la zona D y E, 3,5 y 3,9 cm respectivamente. En este sentido, el nuevo material estudiado es capaz de disminuir, entre un 35% y un 80%, el espesor de la capa aislante, en comparación con paneles de lana de roca o los morteros minerales de mayor capacidad aislante del mercado español respectivamente. ABSTRACT The present doctoral thesis studies a new mineral-based composite material, composed by a gypsum matrix (based on an industrial multiphase gypsum binder) and mesoporous hydrophobic silica aerogel particles, compatibilized with a polymeric surfactant due to the high hydrophobic character of the insulating particles. This study pretends to contribute to the development of new composite insulating materials that could be used in energy renovation of existing dwellings, in order to reduce their high energy consumption, as they represent a great part of the total energy consumed in Spain, but also internationally. Between the materials used to develop de studied insulating mortars, gypsum, besides being an abundant material, especially in Spain, requires less energy for the manufacture of a mineral binder (due to lower manufacturing temperatures), compared to lime or cement, thus presenting lower carbon footprint. In other hand, the hydrophobic mesoporous silica aerogel, is, according to the existing references, the material with the highest know insulating capacity in the market. The development of new mineral mortars with higher thermal insulation capacity than traditional insulating materials, presents a relevant application in energy retrofitting of historic and cultural heritage buildings, in which implies that the insulating material should be installed as an internal layer, rather than as an external insulating system. This type of solution involves a reduced internal useful area, especially in climatic zones where the demand for thermal insulation is higher, and so the insulating layer thickness, being idealistic to use materials with very high insulating properties, in order to reach same insulating level (or higher), but in lower thickness than the provided by traditional insulating materials. This research is developed in three main stages: bibliographic, experimental and simulation. The first stage starts by studying the existing references regarding thermally insulating materials, including existing insulating mortars and insulating panels. The second stage, mainly experimental, is centered in the study of the the influence of the microstructure and macrostructure in the physical and mechanical properties, and also in the thermal conductivity of the new mineral-based material. The thirds stage, through energy simulation, consists in theoretically quantifying the energy savings potential that can provide this type of insulating material, in a particular energy retrofitting case study. The experimental research is mainly focused in the study of the factors that influence the mechanical properties and the thermal conductivity of the thermal insulating mineral composites developed in this thesis. For this, the characterization of the studied materials has been performed, as well as the development of several experimental samples, in order to study the hydration of the mineral binder within the composites, but also the final microstructure and macrostructure, fundamental aspects for the understanding of the composite’s mechanical and insulating properties. Thus, is was possible to determine and quantify the factors that influence the studied material properties, providing a knowledge base and understanding of mineral composites that comprises mesoporous hydrophobic silica aerogel particles, being the first study up to date regarding the specific approach of the present study, regarding not just multiphase calcium sulfate plaster, but also other mineral binders. Particularly, the influence of the incorporation of hydrophobic silica aerogel particles, in high volume ratios into a mineral compound, based on different phases of calcium sulfate has been determined. However, to perform mixing, it is necessary to use a surfactant in order to compatibilize these particles with the water-based mineral binder. The use of such additives has an influence, not only in the aerogel, but the overall properties of the compound, so two different surfactant concentration has been studied: the first, the minimum amount of surfactant (used in this thesis) in order to develop the slurries (0.1% concentration of the mixing water), and the second, as the upper limit, the concentration usually used industrially to stabilize air bubbles in foamed concrete (5%). One of the side effects of using such additive, was the modification of the aerogel particles, by changing their behavior in respect to water, generating a partial invasion of the aerogel’s porous structure, by the mixing water. This behavior produces a very important increase in water/binder ratios, affecting the crystal habit and negatively influencing the mechanical properties of the gypsum matrix. This effect further increased when a higher concentration of surfactant (5%) is used. Regarding final materials properties, it was possible to achieve an ultra-lightweight mineral composite (200 kg/m3), with around 60% by volume of aerogel, presenting a very high insulating capacity (0.028 W/m•K), a noticeable lower thermal conductivity compared to the insulating mortars and traditional thermal insulating panels on the market, such as mineral wool or EPS; however, the limiting factor for future’s material application in buildings, is related to the very low mechanical properties achieved. Among the main factors related to the mechanical properties, it has been found an exponential correlation to the volume of gypsum in the composite. However, second-order factors such as the degree of hydration, or a better distribution of the binder between the aerogel particles, due to the increased surface area of the mineral powder, can increase the mechanical properties between two to three times, depending aerogel volume involved. In addition, it was found that the aerogel, together with the surfactant, is able to entrain a large amount of air volume (around 0.70 m3 per m3 of aerogel), which together with the evaporated water (not consumed by the binder during hydration), can reach generally around 40% of entrained air within the gypsum matrix, regardless of the amount of aerogel in the mixture. Thus, the entrained air into the matrix displaces the volume proportions of the aerogel and gypsum, reducing both mechanical and insulating properties of the mineral composite. On the other hand, it has been observed a direct contribution of three main phases into the thermal conductivity of the composite: gypsum, aerogel and entrained air. Thus, it was possible to develop a mathematical model (adapted from an existing one), capable of calculating quite accurate the thermal conductivity of such mineral composites, from the ratio these three components and for the range of volumes and materials used in this thesis. Finally, the energy simulation performed to a typical Spanish dwelling, from the years 1900 to 1959 (mainly constructed with massive clay bricks), within three climatic zones of Spain (A, D and E), showed the energy savings potential that can provide this type of insulating material, depending on the thickness of the applied layer. Particularly, for the climatic A zone, it has been found an optimal layer thickness of 1 cm, while for zone D and E, 3.5 and 3.9 cm respectively. In this manner, the new studied materials is capable of decreasing the thickness of the insulating layer by 35% and 80%, compared with rock wool panels or mineral mortars with the highest insulating performance of the Spanish market respectively.

Cúpulas de crucero en templos de la provincia de Alicante (s.XVII-XIX): construcción y geometría

El objetivo es determinar las características constructivas, geométricas y materiales en la construcción de cúpulas originales de ladrillo en templos de la provincia de Alicante desde finales del siglo XVII hasta principios del siglo XIX. Se estudian 38 cruceros de iglesias y catedrales en 35 localidades alicantinas mediante recopilación de dibujos originales, levantamiento de planos, construcción en 3D, termografías y toma de muestras, todo ello seguido de un análisis comparativo de variables. Constructivamente, el 88,57 % de las cúpulas simples analizadas son de una hoja de ladrillo macizo (colocado a rosca). Geométricamente, el 97,37 % presentan planta circular y el 92,1 % peralte. El acabado azul vidriado en cubierta es el característico de la provincia (68,42 %), adornado con limatesas en color blanco. Un estudio imprescindible para establecer criterios de uso y conservación, facilitando futuras intervenciones de rehabilitación en este tipo de construcciones religiosas.

Restoration of religious temples: intervention in the church “Nuestra Señora de Belén” in Crevillente (Alicante)

Heritage conservation has raised historical problems usually centered in defects resulting from water leaks. Thus, any intervention is presented as a difficult task, both due to building techniques to be used and the lack of economic resources in many cases. In relation to the temples existing in Alicante (Spain), water drainage is solved with pitched roofs on slope formation (in vaulted naves) or directly supported on the vaulted elements (in the domes). Since those construction systems are composed by brick and plaster, the presence of moisture is problematic, and represents a risk of losing the strength capacity and therefore the stability of the dome. An example of this problem is the dome of the church “Nuestra Señora de Belén” in Crevillente, built with solid bricks, it has the highest diameter of the province (18th century). This historic building has been restored on several occasions in the recent years due to moisture, cracks or fissures. The study of these works give an idea of the difficulties of maintenance, conservation and proper restoration of such kind of buildings as unique and valued constructions in our heritage.

Estimate from Josiah Bemis to John Lowell and Loammi Baldwin for Chelmsford granite, [ca. 1813]

Bemis, responding to an advertisement from Lowell and Baldwin requesting bids for building materials, outlines his proposal for using Chelmsford granite for the construction of University Hall. Bemis lists 12 stipulations in his proposal including costs per bricks, techniques for constructing the upper storeys, and labor costs.