Stability issues in racing motorcycles: an in-depth analysis of the chatter vibration

Racing motorcycles are prone to an unstable oscillatory motion of the swingarm and rear wheel, commonly known as ‘chatter’. This vibration mode typically has a frequency of 17 Hz to 22 Hz and typically occurs during heavy braking manoeuvres. The appearance of chatter can cause reduced rider confidence, and therefore lead to longer lap times during races and the increased risk of crashing. This thesis looks to further the understanding of this mode. It includes the development of a simplified model to explore the effects roll angle and lateral dynamics have on the chatter mode using linear analysis. The mechanisms of instability and parameter sensitivities are also examined. The effects of the nonlinearities present in the minimal model equations of motion are examined, including the identification of limit cycles and their stability, inspecting individual nonlinear terms and their effects, and introducing tyre relaxation and determining the effect it has on the dynamics. Finally, an exploratory study of the mid-corner region of a typical racing manoeuvre is performed in hopes to better understand if any high frequency tyre induced instabilities like chatter can occur.

Clinical Consequences Of Tityus Bahiensis And Tityus Serrulatus Scorpion Stings In The Region Of Campinas, Southeastern Brazil.

Scorpion stings account for most envenomations by venomous animals in Brazil. A retrospective study (1994-2011) of the clinical consequences of Tityus scorpion stings in 1327 patients treated at a university hospital in Campinas, southeastern Brazil, is reported. The clinical classification, based on outcome, was: dry sting (no envenoming), class I (only local manifestations), class II (systemic manifestations), class III (life-threatening manifestations, such as shock and/or cardiac failure requiring inotropic/vasopressor agents, and/or respiratory failure), and fatal. The median patient age was 27 years (interquartile interval = 15-42 years). Scorpions were brought for identification in 47.2% of cases (Tityus bahiensis 27.7%; Tityus serrulatus 19.5%). Sting severity was classified and each accounted for the following percentage of cases: dry stings - 3.4%, class I - 79.6%, class II - 15.1%, class III - 1.8% and fatal - 0.1%. Pain was the primary local manifestation (95.5%). Systemic manifestations such as vomiting, agitation, sweating, dyspnea, bradycardia, tachycardia, tachypnea, somnolence/lethargy, cutaneous paleness, hypothermia and hypotension were detected in class II or class III + fatal groups, but were significantly more frequent in the latter group. Class III and fatal cases occurred only in children <15 years old, with scorpions being identified in 13/25 cases (T. serrulatus, n = 12; T. bahiensis, n = 1). Laboratory blood abnormalities (hyperglycemia, hypokalemia, leukocytosis, elevations in serum total CK, CK-MB and troponin T, bicarbonate consumption and an increase in base deficit and blood lactate), electrocardiographic changes (ST segment) and echocardiographic alterations (ventricular ejected fraction <54%) were frequently detected in class III patients. Seventeen patients developed pulmonary edema, 16 had cardiac failure and seven had cardiogenic shock. These results indicate that most scorpion stings involved only local manifestations, mainly pain; the greatest severity was associated with stings by T. serrulatus and in children <15 years old.

Effects Of High Pressure Homogenization On The Activity, Stability, Kinetics And Three-dimensional Conformation Of A Glucose Oxidase Produced By Aspergillus Niger.

High pressure homogenization (HPH) is a non-thermal method, which has been employed to change the activity and stability of biotechnologically relevant enzymes. This work investigated how HPH affects the structural and functional characteristics of a glucose oxidase (GO) from Aspergillus niger. The enzyme was homogenized at 75 and 150 MPa and the effects were evaluated with respect to the enzyme activity, stability, kinetic parameters and molecular structure. The enzyme showed a pH-dependent response to the HPH treatment, with reduction or maintenance of activity at pH 4.5-6.0 and a remarkable activity increase (30-300%) at pH 6.5 in all tested temperatures (15, 50 and 75°C). The enzyme thermal tolerance was reduced due to HPH treatment and the storage for 24 h at high temperatures (50 and 75°C) also caused a reduction of activity. Interestingly, at lower temperatures (15°C) the activity levels were slightly higher than that observed for native enzyme or at least maintained. These effects of HPH treatment on function and stability of GO were further investigated by spectroscopic methods. Both fluorescence and circular dichroism revealed conformational changes in the molecular structure of the enzyme that might be associated with the distinct functional and stability behavior of GO.

Genetic Diversity Of Giardia Duodenalis: Multilocus Genotyping Reveals Zoonotic Potential Between Clinical And Environmental Sources In A Metropolitan Region Of Brazil.

Giardia duodenalis is a flagellate protozoan that parasitizes humans and several other mammals. Protozoan contamination has been regularly documented at important environmental sites, although most of these studies were performed at the species level. There is a lack of studies that correlate environmental contamination and clinical infections in the same region. The aim of this study is to evaluate the genetic diversity of a set of clinical and environmental samples and to use the obtained data to characterize the genetic profile of the distribution of G. duodenalis and the potential for zoonotic transmission in a metropolitan region of Brazil. The genetic assemblages and subtypes of G. duodenalis isolates obtained from hospitals, a veterinary clinic, a day-care center and important environmental sites were determined via multilocus sequence-based genotyping using three unlinked gene loci. Cysts of Giardia were detected at all of the environmental sites. Mixed assemblages were detected in 25% of the total samples, and an elevated number of haplotypes was identified. The main haplotypes were shared among the groups, and new subtypes were identified at all loci. Ten multilocus genotypes were identified: 7 for assemblage A and 3 for assemblage B. There is persistent G. duodenalis contamination at important environmental sites in the city. The identified mixed assemblages likely represent mixed infections, suggesting high endemicity of Giardia in these hosts. Most Giardia isolates obtained in this study displayed zoonotic potential. The high degree of genetic diversity in the isolates obtained from both clinical and environmental samples suggests that multiple sources of infection are likely responsible for the detected contamination events. The finding that many multilocus genotypes (MLGs) and haplotypes are shared by different groups suggests that these sources of infection may be related and indicates that there is a notable risk of human infection caused by Giardia in this region.

Chitosan Nanoparticles Loaded The Herbicide Paraquat: The Influence Of The Aquatic Humic Substances On The Colloidal Stability And Toxicity.

Polymeric nanoparticles have been developed for several applications, among them as carrier system of pesticides. However, few studies have investigated the fate of these materials in the environment in relation to colloidal stability and toxicity. In nature, humic substances are the main agents responsible for complexation with metals and organic compounds, as well as responsible for the dynamics of these nanoparticles in aquatic and terrestrial environments. In this context, the evaluation of the influence of aquatic humic substances (AHS) on the colloidal stability and toxicity of polymeric nanoparticles of chitosan/tripolyphosphate with or without paraquat was performed. In this study, the nanoparticles were prepared by the ionic gelation method and characterized by size distribution measurements (DLS and NTA), zeta potential, infrared and fluorescence spectroscopy. Allium cepa genotoxicity studies and ecotoxicity assays with the alga Pseudokirchneriella subcapitata were used to investigate the effect of aquatic humic substances (AHS) on the toxicity of this delivery system. No changes were observed in the physical-chemical stability of the nanoparticles due to the presence of AHS using DLS and NTA techniques. However some evidence of interaction between the nanoparticles and AHS was observed by infrared and fluorescence spectroscopies. The ecotoxicity and genotoxicity assays showed that humic substances can decrease the toxic effects of nanoparticles containing paraquat. These results are interesting because they are important for understanding the interaction of these nanostructured carrier systems with species present in aquatic ecosystems such as humic substances, and in this way, opening new perspectives for studies on the dynamics of these carrier systems in the ecosystem.

In Vitro Evaluation Of Sun Protection Factor And Stability Of Commercial Sunscreens Using Mass Spectrometry.

Sunlight exposure causes several types of injury to humans, especially on the skin; among the most common harmful effects due to ultraviolet (UV) exposure are erythema, pigmentation and lesions in DNA, which may lead to cancer. These long-term effects are minimized with the use of sunscreens, a class of cosmetic products that contains UV filters as the main component in the formulation; such molecules can absorb, reflect or diffuse UV rays, and can be used alone or as a combination to broaden the protection on different wavelengths. Currently, worldwide regulatory agencies define which ingredients and what quantities must be used in each country, and enforce companies to conduct tests that confirm the Sun Protection Factor (SPF) and the UVA (Ultraviolet A) factor. Standard SPF determination tests are currently conducted in vivo, using human subjects. In an industrial mindset, apart from economic and ethical reasons, the introduction of an in vitro method emerges as an interesting alternative by reducing risks associated to UV exposure on tests, as well as providing assertive analytical results. The present work aims to describe a novel methodology for SPF determination directly from sunscreen formulations using the previously described cosmetomics platform and mass spectrometry as the analytical methods of choice.

Triatominae Survey (hemiptera: Heteroptera: Reduviidae) In The South-central Region Of The State Of Bahia, Brazil Between 2008 And 2013.

Triatomine surveillance in rural areas, artificial ecotypes, and natural ecotopes of the cities of Caturama, Ibipitanga, Macaúbas, and Seabra in the south-central region of the Brazilian state of Bahia was carried out between 2008 and 2013. Natural infection by Trypanosoma cruzi was evaluated in the specimens collected to monitor vectors of Chagas disease. A total of 1,357 specimens were collected, and four species were identified: Triatoma sordida (83%), Triatoma lenti (16.4%), Triatoma pseudomaculata (0.5%), and Panstrongylus geniculatus (0.1%). Triatoma sordida was found in four cities, only 0.7% in intradomiciliary environments. Triatoma lenti was found only in Macaúbas; 8.5% were found in intradomiciliary environments, 88.3% in peridomiciliary environments, and 3.1% in sylvatic environments. Natural infection by T. cruzi was 0.5% for T. sordida and 3.1% T. lenti. All of these cases were found in peridomiciliary environments of Macaúbas. As the results show, triatomines were found in intradomiciliary environments in three cities that were surveyed in the south-central region of the state of Bahia. Thus, an epidemiologic survey should be performed to avoid the risk of transmission to the population.

Effect of staining solutions and repolishing on color stability of direct composites

OBJECTIVES: The purpose of this study was to assess the color change of three types of composite resins exposed to coffee and cola drink, and the effect of repolishing on the color stability of these composites after staining. MATERIALS AND METHODS: Fifteen specimens (15 mm diameter and 2 mm thick) were fabricated from microhybrid (Esthet-X; Dentsply and Filtek Z-250; 3M ESPE) and high-density hybrid (Surefil; Dentsply) composites, and were finished and polished with aluminum oxide discs (Sof-Lex; 3M ESPE). Color of the specimens was measured according to the CIE L*a*b* system in a refection spectrophotometer (PCB 6807; BYK Gardner). After baseline color measurements, 5 specimens of each resin were immersed in different staining solutions for 15 days: G1 - distilled water (control), G2 - coffee, G3 - cola soft drink. Afterwards, new color measurement was performed and the specimens were repolished and submitted to new color reading. Color stability was determined by the difference (ΔE) between the coordinates L*, a*, and b* obtained from the specimens before and after immersion into the solutions and after repolishing. RESULTS: There was no statistically signifcant difference (ANOVA, Tukey's test; p>0.05) among the ΔE values for the different types of composites after staining or repolishing. For all composite resins, coffee promoted more color change (ΔE>3.3) than distilled water and the cola soft drink. After repolishing, the ΔE values of the specimens immersed in coffee decreased to clinically acceptable values (ΔE<3.3), but remained signifcantly higher than those of the other groups. CONCLUSIONS: No signifcant difference was found among composite resins or between color values before and after repolishing of specimens immersed in distilled water and cola. Immersing specimens in coffee caused greater color change in all types of composite resins tested in this study and repolishing contributed to decrease staining to clinically acceptable ΔE values.

Composite resin color stability: influence of light sources and immersion media

OBJECTIVE: This study evaluated the influence of light sources and immersion media on the color stability of a nanofilled composite resin. MATERIAL AND METHODS: Conventional halogen, high-power-density halogen and high-power-density light-emitting diode (LED) units were used. There were 4 immersion media: coffee, tea, Coke® and artificial saliva. A total of 180 specimens (10 mm x 2 mm) were prepared, immersed in artificial saliva for 24 h at 37±1ºC, and had their initial color measured with a spectrophotometer according to the CIELab system. Then, the specimens were immersed in the 4 media during 60 days. Data from the color change and luminosity were collected and subjected to statistical analysis by the Kruskall-Wallis test (p<0.05). For immersion time, the data were subjected to two-way ANOVA test and Fisher's test (p<0.05). RESULTS: High-power-density LED (ΔE=1.91) promoted similar color stability of the composite resin to that of the tested halogen curing units (Jet Lite 4000 plus - ΔE=2.05; XL 3000 - ΔE=2.28). Coffee (ΔE=8.40; ΔL=-5.21) showed the highest influence on color stability of the studied composite resin. CONCLUSION: There was no significant difference in color stability regardless of the light sources, and coffee was the immersion medium that promoted the highest color changes on the tested composite resin.

Evaluation of iris color stability in ocular prosthesis

Accurate iris reproduction in the fabrication of ocular prosthesis in order to match the remaining eye is a key factor to mask the loss and achieve an esthetic outcome for anophthalmic patients. This study evaluated the stability of acrylic paints used for replicating iris color in ocular prostheses by the analysis of two factors: the temperature of the acrylic resin polymerization cycle during prosthesis fabrication and the incidence of sun light, which is the main photodegrading agent undermining the longevity of ocular prostheses. An accelerated aging assay was used for both analyses. Specimens simulating the prosthetic iris in the colors blue, yellow, black, brown and green were fabricated, and were submitted to a colorimetric reading before and after undergoing the thermal conditions of acrylic resin polymerization. Next, the specimens were submitted to an artificial accelerated aging assay with ultraviolet radiation A and weekly colorimetric readings during a 3-week period. The color change (??*) values for the four specimens painted with the same color paint were averaged and the resulting values were considered for statistical analysis. Levine's test and Student's t-test were used to analyze the influence of the temperature of the polymerization cycle during prosthesis fabrication on the color stability of each acrylic resin paint. Friedman's test for three dependent samples was used for analysis of color photodegradation as function of time. Significance level was set at 0.05 for all analyses. It was observed that, after the action of the temperature of the polymerization cycle, alteration above clinically acceptable level of ??*> 3.3 was observed only for the yellow color. After the accelerated aging assay, there were statistically significant differences (p<0.05) as a function of time in the green, brown, black and blue colors. Changes were clinically acceptable for the brown and black colors; slightly above the clinically acceptable limit for the green color; and significantly high and impracticable from a clinical standpoint for the blue color. There was no statistically significant differences (p>0.05) for the yellow color, which presented color change only a little above the clinically acceptable limit. In conclusion: 1. Only the yellow color presented alterations above the clinically acceptable levels after the polymerization cycle; 2. After accelerated aging, there was no changes in the yellow color above the clinically acceptable levels; 3. For the green color, degradation was significant and slightly above the clinically acceptable levels; 4. The black, brown and blue colors presented significant alterations as function of time; the alterations of the brown and black colors were within acceptable clinical levels, while the blue color presented a more accentuated degradation over time.

Fine needle aspiration biopsy in the oral cavity and head and neck region

The objective of the current study was to evaluate the sensitivity, specificity and accuracy of fine needle aspiration biopsy (FNAB) of submucous nodules from the oral cavity and head and neck region as an auxiliary diagnostic tool. Fifty patients with nodule lesions in the oral cavity and the head and neck region were selected. All of them were submitted to FNAB and to either incisional or excisional biopsy. The diagnoses from the FNABs were compared with the biopsy diagnosis as the gold standard. All the cases of FNAB were analyzed by a single oral pathologist prior to the biopsy diagnosis. The results showed that the sensitivity of FNAB was 75%, its specificity was 96% and its accuracy was 58.8%. The false positive and false negative rates were 6.7% and 13.3%, respectively. The positive predictive value was 86% and the negative predictive value was 93%. The inconclusive rate was 16/50. FNAB displayed a high success rate for identifying both malignant and benign lesions, but a low accuracy for making a final diagnosis.

Detection of Brucella ovis in ovine from Paraíba State, in the Northeast region of Brazil

To determine the presence of Brucella ovis in ovine from Paraíba State, in the Northeast region of Brazil, 80 animals slaughtered in the public slaughterhouse of Patos city were used. Before slaughter, blood samples were collected by jugular venopuncture from each animal, and after slaughter, testicles, epidydimus and uterus were aseptically collected. For the serological diagnosis of B. ovis and B. abortus infections, the agar gel immunodiffusion (AGID) and Rose Bengal (RBT) tests were carried out, respectively. In addition, microbiological culture and polymerase chain reaction (PCR) were performed on testicle, epidydimus and uterus samples. Six animals (7.5%) tested positive for the presence of B. ovis antibodies and all animals tested negative for the presence of B. abortus antibodies. One AGID-positive animal tested positive at uterine swab culture. PCR was able to amplify DNA of Brucella spp. from the pool of testicle, epidydimus and uterus samples from AGID-positive animals. This is the first report of isolation and detection of B. ovis DNA by PCR in ovine from the Northeast region of Brazil.

Association of polymorphisms at the ADIPOR1 regulatory region with type 2 diabetes and body mass index in a Brazilian population with European or African ancestry

Association studies between ADIPOR1 genetic variants and predisposition to type 2 diabetes (DM2) have provided contradictory results. We determined if two single nucleotide polymorphisms (SNP c.-8503G>A and SNP c.10225C>G) in regulatory regions of ADIPOR1 in 567 Brazilian individuals of European (EA; N = 443) or African (AfA; N = 124) ancestry from rural (quilombo remnants; N = 439) and urban (N = 567) areas. We detected a significant effect of ethnicity on the distribution of the allelic frequencies of both SNPs in these populations (EA: -8503A = 0.27; AfA: -8503A = 0.16; P = 0.001 and EA: 10225G = 0.35; AfA: 10225G = 0.51; P < 0.001). Neither of the polymorphisms were associated with DM2 in the case-control study in EA (SNP c.-8503G>A: DM2 group -8503A = 0.26; control group -8503A = 0.30; P = 0.14/SNP 10225C>G: DM2 group 10225G = 0.37; control group 10225G = 0.32; P = 0.40) and AfA populations (SNP c.-8503G>A: DM2 group -8503A = 0.16; control group -8503A = 0.15; P = 0.34/SNP 10225C>G: DM2 group 10225G = 0.51; control group 10225G = 0.52; P = 0.50). Similarly, none of the polymorphisms were associated with metabolic/anthropometric risk factors for DM2 in any of the three populations, except for HDL cholesterol, which was significantly higher in AfA heterozygotes (GC = 53.75 ± 17.26 mg/dL) than in homozygotes. We conclude that ADIPOR1 polymorphisms are unlikely to be major risk factors for DM2 or for metabolic/anthropometric measurements that represent risk factors for DM2 in populations of European and African ancestries.

A new species of the genus Pimelerodius Vanin from the Amazon Region, with notes on the geografic distribution of Pimelerodius motacilla (Boheman) (Coleoptera, Curculionidae, Otidocephalini)

Pimelerodius punctiventris sp. nov. (type locality Brazil, Amazonas, Itacoatiara) is described and illustrated. The new taxon is compared with similar species, being distinguished from the other 12 known species of the genus by the presence of punctures in ventrite I. The available published key for identification of species of Pimelerodius is adapted to include the new species. A modification of the generic description of the aedeagus of Pimelerodius is provided, a necessity due to the differences observed in the aedeagus of the new species. The occurrence of P. motacilla (Boheman, 1843) in the Amazon Region, recorded in sympatry with P. punctiventris in Itacoatiara, AM, is discussed and confirmed, based on the study of 41 available specimens.

On the first tachinid fly (Diptera, Tachinidae) carrying Asclepiadoideae pollinaria in the Neotropical Region

On the first tachinid fly (Diptera, Tachinidae) carrying Asclepiadoideae pollinaria in the Neotropical Region. This paper reports the first Neotropical Tachinidae species possibly associated to pollination of Asclepiadoideae: a female of Euacaulona sumichrasti Townsend, 1908 (Diptera, Tachinidae, Phasiinae, Trichopodini) carrying pollinaria of Gonolobus parviflorus Decne., 1844 (Apocynaceae, Asclepiadoideae, Asclepiadeae: Gonolobinae) attached to its proboscis. The fly specimen was collected in Paraguay, Departamento Canindeyú. The pollinarium is illustrated and described herein. This represents the first anthophilous record to G. parviflorus and to the genus.