Ultra-Fast Gradient LC Method for Omeprazole Analysis Using a Monolithic Column: Assay Development, Validation, and Application to the Quality Control of Omeprazole Enteric-Coated Pellets

A method was optimized for the analysis of omeprazole (OMZ) by ultra-high speed LC with diode array detection using a monolithic Chromolith Fast Gradient RP 18 endcapped column (50 x 2.0 mm id). The analyses were performed at 30 degrees C using a mobile phase consisting of 0.15% (v/v) trifluoroacetic acid (TFA) in water (solvent A) and 0.15% (v/v) TFA in acetonitrile (solvent B) under a linear gradient of 5 to 90% B in 1 min at a flow rate of 1.0 mL/min and detection at 220 nm. Under these conditions, OMZ retention time was approximately 0.74 min. Validation parameters, such as selectivity, linearity, precision, accuracy, and robustness, showed results within the acceptable criteria. The method developed was successfully applied to OMZ enteric-coated pellets, showing that this assay can be used in the pharmaceutical industry for routine QC analysis. Moreover, the analytical conditions established allow for the simultaneous analysis of OMZ metabolites, 5-hydroxyomeprazole and omeprazole sulfone, in the same run, showing that this method can be extended to other matrixes with adequate procedures for sample preparation.

Assignment of the absolute configuration at the sulfur atom of thioridazine metabolites by the analysis of their chiroptical properties: The case of thioridazine 2-sulfoxide

Thioridazine (THD) is a commonly prescribed phenotiazine neuroleptic drug, which is extensively biotransformed in the organism producing as main metabolites sulfoxides and a sulfone by sulfur oxidation Significant differences have been observed in the activity of the THD enantiomers as well as for its main metabolites, and enantioselectivity phenomena have been proved in the metabolic pathway. Here the assignment of the absolute configuration at the sulfur atom of enantiomeric THD-2-sulfoxide (THD-2-SO) has been carried out by circular dichroism (CD) spectroscopy The stereoisomers were separated by HPLC on Chiralpak AS column, recording the CD spectra for the two collected enantiomeric fractions The theoretical electronic CD spectrum has been obtained by the TDDFT/B3LYP/6-31G*. as Boltzmann averaging of the contributions calculated for the most stable conformations of the drug The comparison of the simulated and experimental spectra allowed the absolute configuration at the sulfur atom of the four THD-2-SO stereoisomers to be assigned The developed method should be useful for a reliable correlation between stereochemistry and activity and/or toxicity

In situ gelling hexagonal phases for sustained release of an anti-addiction drug

In this study, fluid precursor formulations for subcutaneous injection and in situ formation of hexagonal phase gels upon water absorption were developed as a strategy to sustain the release of naltrexone, a drug used for treatment of drug addiction. Precursor formulations were obtained by combining BRIJ 97 with propylene glycol (PG, 5-70%, w/w). To study the phase behavior of these formulations, water was added at 10-90% (w/w), and the resulting systems were characterized by polarized light microscopy. Two precursor formulations containing BRIJ:PG at 95:5 (w/w, referred to as BRIJ-95) and at 80:20 (w/w, referred to as BRIJ-80) were chosen. Naltrexone was dissolved at 1% or suspended at 5% (w/w). Precursor formulations were transformed into hexagonal phases when water content exceeded 20%. Water uptake followed second-order kinetics, and after 2-4 h all precursor formulations were transformed into hexagonal phases. Drug release was prolonged by the precursor formulations (compared to a drug solution in PBS), and followed pseudo-first order kinetics regardless of naltrexone concentration. The release from BRIJ-80 was significantly higher than that from BRIJ-95 after 48 h. The relative safety of the precursor formulations was assessed in cultured fibroblasts. Even though BRIJ-95 was more cytotoxic than BRIJ-80, both precursor formulations were significantly less cytotoxic than sodium lauryl sulfate (considered moderate-to-severe irritant) at the same concentration (up to 50 mu g/mL). These results suggest the potential of BRIJ-based precursor formulations for sustained naltrexone release. (C) 2011 Elsevier By. All rights reserved.

Validation of a gas chromatographic method to quantify sesquiterpenes in copaiba oils

Copaifera species (Leguminoseae) are popularly known as ""copaiba"" or ""copaiva"". The oleoresins obtained from the trunk of these species have been extensively used in folk medicine and are commercialized in Brazil as crude oil and in several pharmaceutical and cosmetic products. This work reports a complete validated method for the quantification of beta-caryophyllene, alpha-copaene, and alpha-humulene in distinct copaiba oleoresins available commercially. Thus, essential oil samples (100 mu L) were dissolved in 20 mL of hexanes containing internal standard (1,2,4,5-tetramethylbenzene, 3.0 mM) in a 25 mL glass flask. A 1 mu L aliquot was injected into the GC-FID system. A fused-silica capillary column HP-5, coated with 5% phenylmethylsiloxane was used for this study. The developed method gave a good detection response with linearity in the range of 0.10-18.74 mM. Limits of detection and quantitation variety ranged between 0.003 and 0.091 mM. beta-Caryophyllene, alpha-copaene, and alpha-humulene were recovered in a range from 74.71% to 88.31%, displaying RSD lower than 10% and relative errors between -11.69% and -25.30%. Therefore, this method could be considered as an analytical tool for the quality control of different Copaifera oil samples and its products in both cosmetic and pharmaceutical companies. (C) 2010 Elsevier B.V. All rights reserved.

Development of Vegetable Oil Emulsions with Lamellar Liquid-Crystalline Structures

Emulsions containing vegetable oils and anisotropic phases have especially attractive properties in pharmaceutical technology. They are use as vehicle for different kind of drugs, especially those of topical application. Apart from that, many vegetable oil have pharmacological activity, increasing the necessity for the development of new delivery systems for them. We developed emulsions with vegetable oils at a fixed surfactant ratio and observed the formation of liquid crystalline phases. Nine vegetable oils: Andiroba, Apricot, Avocado, Brazil Nut, Buriti, Cupuassu, Marigold, Passion Fruit and Pequi and mineral oil were tested. Surfactant system was consisted by Steareth-2 and Ceteareth-5. Emulsions were prepared by the emulsion phase inversion (EPI) method, presenting high stability independent on the HLB value. Results indicate that this method could be employed to attain stable emulsions, even if the required HLB value is not known.

A new approach to the granulation of beta-cyclodextrin inclusion complexes

Cyclodextrins (CDs) are annular oligosaccharides containing 6-12 glucose unities joined together by alpha-1,4 bonds. They have a conical-truncated shape with a lipophilic cavity in which different molecules can be included resulting in a stable inclusion complex. The cyclodextrins have been widely applied in pharmaceutical technology with the objective of increasing the solubility, stability and bioavailability of drugs in different pharmaceutical dosage forms, such as tablets. In order to obtain beta-CD tablets, liquid dispersions of drug/beta-CD are usually submitted to different drying processes, like spray-drying, freeze-drying or slow evaporation, being this dry material added to a number of excipients. However, such drying processes can generate particulate materials showing problems of flow and compressibility, needing their conversion into granulates by means of wetting with granulation liquid followed by additional drying. In this work, the main objective was to evaluate the preparation of tablets without the need of this additional drying step. For this purpose an aqueous dispersion containing acetaminophen/beta-CD complex and cornstarch was dried using a spouted bed and the obtained granules were compressed in tablets. Acetaminophen was used as model drug due to its low water solubility and the inexpensive and widely available cornstarch was chosen as excipient. Acetaminophen powder was added into a beta-cyclodextrin solution prepared in distilled water at 70 degrees C. Stirring was kept until this dispersion cooled to room temperature. Then cornstarch was added and the resulting dispersion was dried in spouted bed equipment. This material was compressed into tablets using an Erweka Korsh EKO tablet machine. This innovative approach allowed the tablets preparation process to be carried out with fewer steps and represents a technological reliable strategy to produce beta-cyclodextrin inclusion complexes tablets. (C) 2010 Elsevier By. All rights reserved.

Essential Oil of Thymus vulgaris: Preparation of Pharmaceutical Mouthwash Formulation and In Vitro Evaluation of the Bacterial Plaque-Inhibiting Properties.

Essential Oil of Thymus vulgaris: Preparation of Pharmaceutical Mouthwash Formulation and In Vitro Evaluation of the Bacterial Plaque-Inhibiting Properties. The aim of this study was to evaluate the in vitro effect of the essential oil of Thymus vulgaris (thyme) pure or incorporate in a alcohol-free pharmaceutical mouthwash formulation, against Streptococcus mutans (ATCC 25175), being determined the Minimal Inhibitory Concentration (MIC) and the effect in the bacterial plate formation. The MIC value obtained for the essential oil was 100 mu g/mL (1 %). The mouthwash pharmaceutical formulation containing commercial essential oil of T. vulgaris was preparated. Microbiological and macroscopic analysis as well as analyses for MEV confirmed the effectiveness of this new alcohol-free mouthwash formulation containing essential oil of T. vulgaris as agent with plaque-inhibiting properties and possible application in the preventive dentistry. The chemical characterization of the bioactive essential oil was accomplished by CG-MS, being verified the presence of carvacrol, p-cimene and alpha-pinene as major constituents.

Trypanocidal, leislimanicidal and antifungal potential from marine red alga Bostrychia tenella J. Agardli (Rhodomelaceae, Ceraniiales)

Specimens of the red alga Bostrychia tenella J Agardh (Rhodomelaceae, Ceramiales) were collected from the Sao Paulo coast and submitted to loom temperature solvent extraction The resulting extract was fractionated by partitioning with organic solvent The n-hexane (BT-H) and dichloromethane (BT-D) fractions showed antiprotozoal potential in biological tests with Trypanosoma cruzi and Leishmania amazonensis and presented high activity in an antifungal assay with the phytopathogenic fungi Cladosporium cladosporioides and Cladosporium sphaerospermum Chromatography methods were used to generate subfractions from BT-H (H01 to H11) and from BT-D (D01 to 019) The subtractions were analyzed by gas chromatography-mass spectrometry (GC/MS). and the substances were identified by retention index (Kovats) and by comparison to databases of commercial mass spectra The volatile compounds found in marine algae were identified as fatty acids, low molecular mass hydrocarbons, esters and steroids, some of these have been previously described in the literature based on other biological activities Moreover, uncommon substances. such as neophytadiene were also identified In a trypanocidal assay, fractions BT-H and BT-D showed IC(50) values of 168 and 19 1 mu g/mL. respectively, and were mote active than the gentian violet standard (31 mu g/ml.); subfractions H02. H03, D01 and D02 were active against L amasonensis, exhibiting IC(50) values of 1 S. 2 7, 4 4. and 4 3 mu g/mL., respectively (standard amphotericin B IC(50) = 13 mu g/mL.) All fractions showed antifungal potential this work reports the biological activity and identification of compounds by GC/MS for the marine red alga B tenella for the first time (C) 2010 Elsevier B V All lights reserved

Nuclear Quadrupole Resonance: A Technique to Control Hydration Processes in the Pharmaceutical Industry

Pharmaceuticals can exist in many solid forms, which can have different physical and chemical properties. These solid forms include polymorphs, solvates, amorphous, and hydrates. Particularly, hydration process can be quite common since pharmaceutical solids can be in contact with water during manufacturing process and can also be exposed to water during storage. In the present work, it is proved that NQR technique is capable of detecting different hydrated forms not only in the pure raw material but also in the final product (tablets), being in this way a useful technique for quality control. This technique was also used to study the dehydration process from pentahydrate to trihydrate.

Effect of a 36-month pharmaceutical care program on pharmacotherapy adherence in elderly diabetic and hypertensive patients

Objective: The primary objective of this study was to evaluate the effect of a pharmaceutical care program on pharmacotherapy adherence in elderly diabetic and hypertensive patients. The clinical outcomes of this pharmacotherapy adherence approach were the secondary objective of the study. Setting: Public Primary Health Care Unit in a municipality in the Brazilian State of Sao Paulo. Method: A 36-month randomized, controlled, prospective clinical trial was carried out with 200 patients divided into two groups: control (n = 100) and intervention (n = 100). The control group received the usual care offered by the Primary Health Care Unit (medical and nurse consultancies). The patients randomized into the intervention group received pharmaceutical care intervention besides the usual care offered. Main outcome measure: Pharmacotherapy adherence (Morisky-Green test translated into Portuguese and computerized dispensed medication history) and clinical measurements (blood pressure, fasting glucose, A1C hemoglobin, triglycerides and total cholesterol) were evaluated at the baseline and up to 36 months. A P value < 0.05 was considered statistically significant. Results: A total of 97 patients from the intervention group and 97 patients from the control group completed the study (n = 194). Significant improvements in the pharmacotherapy adherence were verified for the intervention group according to the Morisky-Green test (50.5% of adherent patients at baseline vs. 83.5% of adherent patients after 36 months; P < 0.001) and the computerized dispensed medication history (52.6% of adherent patients at baseline vs. 83.5% of adherent patients after 36 months; P < 0.001); no significant changes were verified in the control group. Significant improvements in the number of patients reaching adequate values for their blood pressure (26.8% at baseline vs. 86.6% after 36-months; P < 0.001), fasting glucose (29.9% at baseline vs. 70.1% after 36 months; P < 0.001), A1C hemoglobin (3.3% at baseline vs. 63.3% after 36 months; P < 0.001), triglycerides (47.4% at baseline vs. 74.2% after 36 months; P < 0.001) and total cholesterol (59.8% at baseline vs. 80.4% after 36 months; P = 0.002) were verified in the intervention group, but remained unchanged in the control group. Conclusion: These results indicated the effectiveness of pharmaceutical care in improving pharmacotherapy adherence, with positive effects in the clinical outcomes of the patients studied.

Analysis of Liquid Crystalline Nanoparticles by Small Angle X-Ray Diffraction: Evaluation of Drug and Pharmaceutical Additives Influence on the Internal Structure

The goal of this work was to study the liquid crystalline structure of a nanodispersion delivery system intended to be used in photodynamic therapy after loading with photosensitizers (PSs) and additives such as preservatives and thickening polymers. Polarized light microscopy and light scattering were performed on a standard nanodispersion in order to determine the anisotropy of the liquid crystalline structure and the mean diameter of the nanoparticles, respectively. Small angle X-ray diffraction (SAXRD) was used to verify the influence of drug loading and additives on the liquid crystalline structure of the nanodispersions. The samples, before and after the addition of PSs and additives, were stable over 90 days, as verified by dynamic light scattering. SAXRD revealed that despite the alteration observed in some of the samples analyzed in the presence of photosensitizing drugs and additives, the hexagonal phase still remained in the crystalline phase. (C) 2011 Wiley-Liss, Inc. and the American Pharmacists Association J Pharm Sci 100: 2849-2857, 2011

The prospects for tobacco harm reduction

Tobacco harm reduction (THR) policies aim to reduce the prevalence of tobacco-related harm by encouraging smokers who are unable or unwilling to quit to adopt less harmful ways of obtaining nicotine, such as pharmaceutical nicotine and oral tobacco snuff. Proponents of THR argue that the effects of tobacco control policies have reduced smoking as much as they reasonably can and that we can best reduce tobacco-related harm by encouraging smokers to use these methods, which substantially reduce the health risks of smoking. Critics argue that THR policies will undermine the two traditional tobacco control goals of preventing the uptake of smoking by young people and encouraging smokers to quit. I assess the main arguments and evidence advanced for and against THR.

Design, Science and Conceptual Analysis

Philosophers expend considerable effort on the analysis of concepts, but the value of such work is not widely appreciated. This paper principally analyses some arguments, beliefs, and presuppositions about the nature of design and the relations between design and science common in the literature to illustrate this point, and to contribute to the foundations of design theory.

School Science Lessons

This website is linked to UNESCO.org and is free to download for educational purposes. It contains a database of school science experiments and investigations in physics, chemistry, biology, astronomy, geology, weather studies, agriculture projects for primary and secondary schools; and sexuality education and drugs education. It is based on a revision, updating and expansion of the "New UNESCO source book for science teaching", 1979 edition, UNESCO, Paris. It contains experiments from the "low cost" science teaching movement, simplified versions of classical experiments, experiments using locally available substances and kitchen chemicals, and environmental science. Some experiments anticipate experiments usually done in senior high school or college classes. The experiments should be "student-friendly" and "teacher-friendly" because there is no overwhelming technology. Enough theoretical background is included to remind teachers of the theoretical context of the experiment. Every experiment is based on materials listed in a modern commercial catalogue of chemicals and equipment for use by educational institutions. The procedures and safety standards are consistent with instructions issued by Education Queensland (Ministry of Education), State of Queensland, Australia.