Pore structure characterization of North American shale gas reservoirs using USANS/SANS, gas adsorption, and mercury intrusion

Small-angle and ultra-small-angle neutron scattering (SANS and USANS), low-pressure adsorption (N2 and CO2), and high-pressure mercury intrusion measurements were performed on a suite of North American shale reservoir samples providing the first ever comparison of all these techniques for characterizing the complex pore structure of shales. The techniques were used to gain insight into the nature of the pore structure including pore geometry, pore size distribution and accessible versus inaccessible porosity. Reservoir samples for analysis were taken from currently-active shale gas plays including the Barnett, Marcellus, Haynesville, Eagle Ford, Woodford, Muskwa, and Duvernay shales. Low-pressure adsorption revealed strong differences in BET surface area and pore volumes for the sample suite, consistent with variability in composition of the samples. The combination of CO2 and N2 adsorption data allowed pore size distributions to be created for micro–meso–macroporosity up to a limit of �1000 Å. Pore size distributions are either uni- or multi-modal. The adsorption-derived pore size distributions for some samples are inconsistent with mercury intrusion data, likely owing to a combination of grain compression during high-pressure intrusion, and the fact that mercury intrusion yields information about pore throat rather than pore body distributions. SANS/USANS scattering data indicate a fractal geometry (power-law scattering) for a wide range of pore sizes and provide evidence that nanometer-scale spatial ordering occurs in lower mesopore–micropore range for some samples, which may be associated with inter-layer spacing in clay minerals. SANS/USANS pore radius distributions were converted to pore volume distributions for direct comparison with adsorption data. For the overlap region between the two methods, the agreement is quite good. Accessible porosity in the pore size (radius) range 5 nm–10 lm was determined for a Barnett shale sample using the contrast matching method with pressurized deuterated methane fluid. The results demonstrate that accessible porosity is pore-size dependent.

Mapping of multiple quantitative trait loci affecting bovine spongiform encephalopathy

A whole-genome scan was conducted to map quantitative trait loci (QTL) for BSE resistance or susceptibility. Cows from four half-sib families were included and 173 microsatellite markers were used to construct a 2835-cM (Kosambi) linkage map covering 29 autosomes and the pseudoautosomal region of the sex chromosome. Interval mapping by linear regression was applied and extended to a multiple-QTL analysis approach that used identified QTL on other chromosomes as cofactors to increase mapping power. In the multiple-QTL analysis, two genome-wide significant QTL (BTA17 and X/Y ps) and four genome-wide suggestive QTL (BTA1, 6, 13, and 19) were revealed. The QTL identified here using linkage analysis do not overlap with regions previously identified using TDT analysis. One factor that may explain the disparity between the results is that a more extensive data set was used in the present study. Furthermore, methodological differences between TDT and linkage analyses may affect the power of these approaches.

A vibrational spectroscopic study of philipsbornite PbAl3(AsO4)2(OH)5⋅H2O-molecular structural implications and relationship to the crandallite subgroup arsenates

The presence of arsenic in the environment is a hazard. The accumulation of arsenate by a range of cations in the formation of minerals provides a mechanism for the remediation of arsenate contamination. The formation of the crandallite group of minerals provides a mechanism for arsenate accumulation. Among the crandallite minerals are philipsbornite, arsenocrandallite and arsenogoyazite. Raman spectroscopy complimented with infrared spectroscopy has enabled aspects of the structure of philipsbornite to be studied. The Raman spectrum of philipsbornite displays an intense band at around 840 cm−1 attributed to the overlap of the symmetric and antisymmetric stretching modes. Raman bands observed at 325, 336, 347, 357, 376 and 399 cm−1 are assigned to the ν2 (AsO4)3− symmetric bending vibration (E) and to the ν4 bending vibration (F2). The observation of multiple bending modes supports the concept of a reduction in symmetry of the arsenate anion in philipsbornite. Evidence for phosphate in the mineral is provided. By using an empirical formula, hydrogen bond distances for the OH units in philipsbornite of 2.8648 Å, 2.7864 Å, 2.6896 Å cm−1 and 2.6220 were calculated.

Conceptualising, operationalising and measuring the player experience in videogames

The player experience is at the core of videogame play. Understanding the facets of player experience presents many research challenges, as the phenomenon sits at the intersection of psychology, design, human-computer interaction, sociology, and physiology. This workshop brings together an interdisciplinary group of researchers to systematically and rigorously analyse all aspects of the player experience. Methods and tools for conceptualising, operationalising and measuring the player experience form the core of this research. Our aim is to take a holistic approach to identifying, adapting and extending theories and models of the player experience, to understand how these theories and models interact, overlap and differ, and to construct a unified vision for future research.

Improving the measurement and surveillance of child abuse in Queensland emergency departments

There are no population studies of prevalence or incidence of child maltreatment in Australia. Child protection data gives some understanding but is restricted by system capacity and definitional issues across jurisdictions. Child protection data currently suggests that numbers of reports are increasing yearly, and the child protection system then becomes focussed on investigating all reports and diluting available resources for those children who are most in need of intervention. A public health response across multiple agencies enables responses to child safety across the entire population. All families are targeted at the primary level; examples include ensuring all parents know the dangers of shaking a baby or teaching children to say no if a situation makes them uncomfortable. The secondary level of prevention targets families with a number of risk factors, for example subsidised child care so children aren't left unsupervised after school when both parents have to be at work or home visiting for drug-addicted parents to ensure children are cared for. The tertiary response then becomes the responsibility of the child protection system and is reserved for those children where abuse and neglect are identified. This model requires that child safety is seen in a broader context than just the child protection system, and increasingly health professionals are being identified as an important component in the public health framework. If all injury is viewed as preventable and considered along a continuum of 'accidental' through to 'inflicted', it becomes possible to conceptualise child maltreatment in an injury context. Parental intent may not be to cause harm to the child, but by lack of insight or concern about risk, the potential for injury is high. The mechanisms for unintentional and intentional injury overlap and some suggest that by segregating child abuse (with the possible exception of sexual abuse) from unintentional injury, child abuse is excluded from the broader injury prevention initiative that is gaining momentum in the community. This research uses a public health perspective, specifically that of injury prevention, to consider the problem of child abuse. This study employed a mixed method design that incorporates secondary data analysis, data linkage and structured interviews of different professional groups. Datasets from the Queensland Injury Surveillance Unit (QISU) and The Department of Child Safety (DCS) were evaluated. Coded injury data was grouped according to intent of injury according to those with a code that indicated the ED presentation was due to child abuse, a code indicating that the injury was possibly due to abuse or, in the third group, the intent code indicated that the injury was unintentional and not due to abuse. Primary data collection from ED records was undertaken and information recoded to assess reliability and completeness. Emergency department data (QISU) was linked to Department of Child Safety Data to examine concordance and data quality. Factors influencing the collection and collation of these data were identified through structured interview methodology and analysed using qualitative methods. Secondary analysis of QISU data indicated that codes lacking specific information on the injury event were more likely to also have an intent code indicating abuse than those records where there was specific information on the injury event. Codes for abuse appeared in only 1.2% of the 84,765 records analysed. Unintentional injury was the most commonly coded intent (95.3%). In the group with a definite abuse code assigned at triage, 83% linked to a record with DCS and cases where documentation indicated police involvement were significantly more likely to be associated with a DCS record than those without such documentation. In those coded with an unintentional injury code, 22% linked to a DCS record with cases assigned an urgent triage category more likely to link than those with a triage category for resuscitation and children who presented to regional or remote hospitals more likely to link to a DCS record than those presenting to urban hospitals. Twenty-nine per cent of cases with a code indicating possible abuse linked to a DCS record. In documentation that indicated police involvement in the case, a code for unspecified activity when compared to cases with a code indicating involvement in a sporting activity and children less than 12 months of age compared to those in the 13-17 year old age group were all variables significantly associated with linkage to a DCS record. Only 13% of records contained documentation indicating that child abuse and neglect were considered in the diagnosis of the injury despite almost half of the sample having a code of abuse or possible abuse. Doctors and nurses were confident in their knowledge of the process of reporting child maltreatment but less confident about identifying child abuse and neglect and what should be reported. Many were concerned about implications of reporting, for the child and family and for themselves. A number were concerned about the implications of not reporting, mostly for the wellbeing of the child and a few in terms of their legal obligations as mandatory reporters. The outcomes of this research will help improve the knowledge of barriers to effective surveillance of child abuse in emergency departments. This will, in turn, ensure better identification and reporting practises; more reliable official statistical collections and the potential of flagging high-risk cases to ensure adequate departmental responses have been initiated.

The contribution of psychosocial factors to socioeconomic differences in food purchasing

In developed countries the relationship between socioeconomic position (SEP) and health is unequivocal. Those who are socioeconomically disadvantaged are known to experience higher morbidity and mortality from a range of chronic diet-related conditions compared to those of higher SEP. Socioeconomic inequalities in diet are well established. Compared to their more advantaged counterparts, those of low SEP are consistently found to consume diets less consistent with dietary guidelines (i.e. higher in fat, salt and sugar and lower in fibre, fruit and vegetables). Although the reasons for dietary inequalities remain unclear, understanding how such differences arise is important for the development of strategies to reduce health inequalities. Both environmental (e.g. proximity of supermarkets, price, and availability of foods) and psychosocial (e.g. taste preference, nutrition knowledge) influences are proposed to account for inequalities in food choices. Although in the United States (US), United Kingdom (UK), and parts of Australia, environmental factors are associated with socioeconomic differences in food choices, these factors do not completely account for the observed inequalities. Internationally, this context has prompted calls for further exploration of the role of psychological and social factors in relation to inequalities in food choices. It is this task that forms the primary goal of this PhD research. In the small body of research examining the contribution of psychosocial factors to inequalities in food choices, studies have focussed on food cost concerns, nutrition knowledge or health concerns. These factors are generally found to be influential. However, since a range of psychosocial factors are known determinants of food choices in the general population, it is likely that a range of factors also contribute to inequalities in food choices. Identification of additional psychosocial factors of relevance to inequalities in food choices would provide new opportunities for health promotion, including the adaption of existing strategies. The methodological features of previous research have also hindered the advancement of knowledge in this area and a lack of qualitative studies has resulted in a dearth of descriptive information on this topic. This PhD investigation extends previous research by assessing a range of psychosocial factors in relation to inequalities in food choices using both quantitative and qualitative techniques. Secondary data analyses were undertaken using data obtained from two Brisbane-based studies, the Brisbane Food Study (N=1003, conducted in 2000), and the Sixty Families Study (N=60, conducted in 1998). Both studies involved main household food purchasers completing an interviewer-administered survey within their own home. Data pertaining to food-purchasing, and psychosocial, socioeconomic and demographic characteristics were collected in each study. The mutual goals of both the qualitative and quantitative phases of this investigation were to assess socioeconomic differences in food purchasing and to identify psychosocial factors relevant to any observed differences. The quantitative methods then additionally considered whether the associations examined differed according to the socioeconomic indicator used (i.e. income or education). The qualitative analyses made a unique contribution to this project by generating detailed descriptions of socioeconomic differences in psychosocial factors. Those with lower levels of income and education were found to make food purchasing choices less consistent with dietary guidelines compared to those of high SEP. The psychosocial factors identified as relevant to food-purchasing inequalities were: taste preferences, health concerns, health beliefs, nutrition knowledge, nutrition concerns, weight concerns, nutrition label use, and several other values and beliefs unique to particular socioeconomic groups. Factors more tenuously or inconsistently related to socioeconomic differences in food purchasing were cost concerns, and perceived adequacy of the family diet. Evidence was displayed in both the quantitative and qualitative analyses to suggest that psychosocial factors contribute to inequalities in food purchasing in a collective manner. The quantitative analyses revealed that considerable overlap in the socioeconomic variation in food purchasing was accounted for by key psychosocial factors of importance, including taste preference, nutrition concerns, nutrition knowledge, and health concerns. Consistent with these findings, the qualitative transcripts demonstrated the interplay between such influential psychosocial factors in determining food-purchasing choices. The qualitative analyses found socioeconomic differences in the prioritisation of psychosocial factors in relation to food choices. This is suggestive of complex cultural factors that distinguish advantaged and disadvantaged groups and result in socioeconomically distinct schemas related to health and food choices. Compared to those of high SEP, those of lower SEP were less likely to indicate that health concerns, nutrition concerns, or food labels influenced food choices, and exhibited lower levels of nutrition knowledge. In the absence of health or nutrition-related concerns, taste preferences tended to dominate the food purchasing choices of those of low SEP. Overall, while cost concerns did not appear to be a main determinant of socioeconomic differences in food purchasing, this factor had a dominant influence on the food choices of some of the most disadvantaged respondents included in this research. The findings of this study have several implications for health promotion. The integrated operation of psychosocial factors on food purchasing inequalities indicates that multiple psychosocial factors may be appropriate to target in health promotion. It also seems possible that the inter-relatedness of psychosocial factors would allow health promotion targeting a single psychosocial factor to have a flow-on affect in terms of altering other influential psychosocial factors. This research also suggests that current mass marketing approaches to health promotion may not be effective across all socioeconomic groups due to differences in the priorities and main factors of influence in food purchasing decisions across groups. In addition to the practical recommendations for health promotion, this investigation, through the critique of previous research, and through the substantive study findings, has highlighted important methodological considerations for future research. Of particular note are the recommendations pertaining to the selection of socioeconomic indicators, measurement of relevant constructs, consideration of confounders, and development of an analytical approach. Addressing inequalities in health has been noted as a main objective by many health authorities and governments internationally. It is envisaged that the substantive and methodological findings of this thesis will make a useful contribution towards this important goal.

Role of charge in destabilizing AlH4 and BH4 complex anions for hydrogen storage applications : Ab initio density functional calculations

NaAlH4 and LiBH4 are potential candidate materials for mobile hydrogen storage applications, yet they have the drawback of being highly stable and desorbing hydrogen only at elevated temperatures. In this letter, ab initio density functional theory calculations reveal how the stabilities of the AlH4 and BH4 complex anions will be affected by reducing net anionic charge. Tetrahedral AlH4 and BH4 complexes are found to be distorted with the decrease of negative charge. One H-H distance becomes smaller and the charge density will overlap between them at a small anion charge. The activation energies to release of H2 from AlH4 and BH4 complexes are thus greatly decreased. We demonstrate that point defects such as neutral Na vacancies or substitution of a Na atom with Ti on the NaAlH4(001) surface can potentially cause strong distortion of neighboring AlH4 complexes and even induce spontaneous dehydrogenation. Our results help to rationalize the conjecture that the suppression of charge transfer to AlH4 and BH4 anion as a consequence of surface defects should be very effective for improving the recycling performance of H2 in NaAlH4 and LiBH4. The understanding gained here will aid in the rational design and development of hydrogen storage materials based on these two systems.

From solving puzzles to designing solutions : integrating design thinking into evidence based practice

Evidence based practice (EBP) focuses on solving ‘tame’ problems, where literature supports question construction toward determining a solution. What happens when there is no existing evidence, or when the need for agility precludes a full EBP implementation? How might we build a more agile and innovative practice that facilitates the design of solutions to complex and wicked problems, particularly in cases where there is no existing literature? As problem solving and innovation methods, EBP and design thinking overlap considerably. The literature indicates the potential benefits to be gained for evidence based practice from adopting a human-centred rather than literature-focused foundation. The design thinking process is social and collaborative by nature, which enables it to be more agile and produce more innovative results than evidence based practice. This paper recommends a hybrid approach to maximise the strengths and benefits of the two methods for designing solutions to wicked problems. Incorporating design thinking principles and tools into EBP has the potential to move its applicability beyond tame problems and continuous improvement, and toward wicked problem solving and innovation. The potential of this hybrid approach in practice is yet to be explored.

Error and uncertainty of adult age estimation of the pubic symphysis in an Australian sub-population using computed tomography

After attending this presentation, attendees will gain awareness of: (1) the error and uncertainty associated with the application of the Suchey-Brooks (S-B) method of age estimation of the pubic symphysis to a contemporary Australian population; (2) the implications of sexual dimorphism and bilateral asymmetry of the pubic symphysis through preliminary geometric morphometric assessment; and (3) the value of three-dimensional (3D) autopsy data acquisition for creating forensic anthropological standards. This presentation will impact the forensic science community by demonstrating that, in the absence of demographically sound skeletal collections, post-mortem autopsy data provides an exciting platform for the construction of large contemporary ‘virtual osteological libraries’ for which forensic anthropological research can be conducted on Australian individuals. More specifically, this study assesses the applicability and accuracy of the S-B method to a contemporary adult population in Queensland, Australia, and using a geometric morphometric approach, provides an insight to the age-related degeneration of the pubic symphysis. Despite the prominent use of the Suchey-Brooks (1990) method of age estimation in forensic anthropological practice, it is subject to intrinsic limitations, with reports of differential inter-population error rates between geographical locations1-4. Australian forensic anthropology is constrained by a paucity of population specific standards due to a lack of repositories of documented skeletons. Consequently, in Australian casework proceedings, standards constructed from predominately American reference samples are applied to establish a biological profile. In the global era of terrorism and natural disasters, more specific population standards are required to improve the efficiency of medico-legal death investigation in Queensland. The sample comprises multi-slice computed tomography (MSCT) scans of the pubic symphysis (slice thickness: 0.5mm, overlap: 0.1mm) on 195 individuals of caucasian ethnicity aged 15-70 years. Volume rendering reconstruction of the symphyseal surface was conducted in Amira® (v.4.1) and quantitative analyses in Rapidform® XOS. The sample was divided into ten-year age sub-sets (eg. 15-24) with a final sub-set of 65-70 years. Error with respect to the method’s assigned means were analysed on the basis of bias (directionality of error), inaccuracy (magnitude of error) and percentage correct classification of left and right symphyseal surfaces. Morphometric variables including surface area, circumference, maximum height and width of the symphyseal surface and micro-architectural assessment of cortical and trabecular bone composition were quantified using novel automated engineering software capabilities. The results of this study demonstrated correct age classification utilizing the mean and standard deviations of each phase of the S-B method of 80.02% and 86.18% in Australian males and females, respectively. Application of the S-B method resulted in positive biases and mean inaccuracies of 7.24 (±6.56) years for individuals less than 55 years of age, compared to negative biases and mean inaccuracies of 5.89 (±3.90) years for individuals greater than 55 years of age. Statistically significant differences between chronological and S-B mean age were demonstrated in 83.33% and 50% of the six age subsets in males and females, respectively. Asymmetry of the pubic symphysis was a frequent phenomenon with 53.33% of the Queensland population exhibiting statistically significant (χ2 - p<0.01) differential phase classification of left and right surfaces of the same individual. Directionality was found in bilateral asymmetry, with the right symphyseal faces being slightly older on average and providing more accurate estimates using the S-B method5. Morphometric analysis verified these findings, with the left surface exhibiting significantly greater circumference and surface area than the right (p<0.05). Morphometric analysis demonstrated an increase in maximum height and width of the surface with age, with most significant changes (p<0.05) occurring between the 25-34 and 55-64 year age subsets. These differences may be attributed to hormonal components linked to menopause in females and a reduction in testosterone in males. Micro-architectural analysis demonstrated degradation of cortical composition with age, with differential bone resorption between the medial, ventral and dorsal surfaces of the pubic symphysis. This study recommends that the S-B method be applied with caution in medico-legal death investigations of unknown skeletal remains in Queensland. Age estimation will always be accompanied by error; therefore this study demonstrates the potential for quantitative morphometric modelling of age related changes of the pubic symphysis as a tool for methodological refinement, providing a rigor and robust assessment to remove the subjectivity associated with current pelvic aging methods.

A genome-wide scan provides evidence for loci influencing a severe heritable form of common migraine

Migraine is a prevalent neurovascular disease with a significant genetic component. Linkage studies have so far identified migraine susceptibility loci on chromosomes 1, 4, 6, 11, 14, 19 and X. We performed a genome-wide scan of 92 Australian pedigrees phenotyped for migraine with and without aura and for a more heritable form of “severe” migraine. Multipoint non-parametric linkage analysis revealed suggestive linkage on chromosome 18p11 for the severe migraine phenotype (LOD*=2.32, P=0.0006) and chromosome 3q (LOD*=2.28, P=0.0006). Excess allele sharing was also observed at multiple different chromosomal regions, some of which overlap with, or are directly adjacent to, previously implicated migraine susceptibility regions. We have provided evidence for two loci involved in severe migraine susceptibility and conclude that dissection of the “migraine” phenotype may be helpful for identifying susceptibility genes that influence the more heritable clinical (symptom) profiles in affected pedigrees. Also, we concluded that the genetic aetiology of the common (International Headache Society) forms of the disease is probably comprised of a number of low to moderate effect susceptibility genes, perhaps acting synergistically, and this effect is not easily detected by traditional single-locus linkage analyses of large samples of affected pedigrees.

Retrieval of health advice on the web: AEHRC at ShARe/CLEF eHealth Evaluation Lab Task 3

This paper details the participation of the Australian e- Health Research Centre (AEHRC) in the ShARe/CLEF 2013 eHealth Evaluation Lab { Task 3. This task aims to evaluate the use of information retrieval (IR) systems to aid consumers (e.g. patients and their relatives) in seeking health advice on the Web. Our submissions to the ShARe/CLEF challenge are based on language models generated from the web corpus provided by the organisers. Our baseline system is a standard Dirichlet smoothed language model. We enhance the baseline by identifying and correcting spelling mistakes in queries, as well as expanding acronyms using AEHRC's Medtex medical text analysis platform. We then consider the readability and the authoritativeness of web pages to further enhance the quality of the document ranking. Measures of readability are integrated in the language models used for retrieval via prior probabilities. Prior probabilities are also used to encode authoritativeness information derived from a list of top-100 consumer health websites. Empirical results show that correcting spelling mistakes and expanding acronyms found in queries signi cantly improves the e ectiveness of the language model baseline. Readability priors seem to increase retrieval e ectiveness for graded relevance at early ranks (nDCG@5, but not precision), but no improvements are found at later ranks and when considering binary relevance. The authoritativeness prior does not appear to provide retrieval gains over the baseline: this is likely to be because of the small overlap between websites in the corpus and those in the top-100 consumer-health websites we acquired.

Scene invariant multi camera crowd counting

Automated crowd counting has become an active field of computer vision research in recent years. Existing approaches are scene-specific, as they are designed to operate in the single camera viewpoint that was used to train the system. Real world camera networks often span multiple viewpoints within a facility, including many regions of overlap. This paper proposes a novel scene invariant crowd counting algorithm that is designed to operate across multiple cameras. The approach uses camera calibration to normalise features between viewpoints and to compensate for regions of overlap. This compensation is performed by constructing an 'overlap map' which provides a measure of how much an object at one location is visible within other viewpoints. An investigation into the suitability of various feature types and regression models for scene invariant crowd counting is also conducted. The features investigated include object size, shape, edges and keypoints. The regression models evaluated include neural networks, K-nearest neighbours, linear and Gaussian process regresion. Our experiments demonstrate that accurate crowd counting was achieved across seven benchmark datasets, with optimal performance observed when all features were used and when Gaussian process regression was used. The combination of scene invariance and multi camera crowd counting is evaluated by training the system on footage obtained from the QUT camera network and testing it on three cameras from the PETS 2009 database. Highly accurate crowd counting was observed with a mean relative error of less than 10%. Our approach enables a pre-trained system to be deployed on a new environment without any additional training, bringing the field one step closer toward a 'plug and play' system.

Closing the gap between copyright and designs : an age of enlightnement or state of confusion?

The arena of intellectual property encompasses streams that often interrelate and overlap in protecting different aspects of intellectual property. Australian commentators suggest that ‘one of the most troublesome areas in the entire field of intellectual property has been the relationship between copyright protection for artistic works under the Copyright Act 1968 (Cth) and protection for registered designs under the Designs Act 1906 (Cth).’ [McKeough, J., Stewart, A., & Griffith, P. (2004). Intellectual property in Australia (3rd ed.). Chatswood, NSW: Butterworths.] [Ricketson, S., Richardson, M., & Davison, M. (2009). Intellectual property: Cases, materials and commentary (4th ed.). Chatswood, NSW: LexisNexis Butterworths.] This overlap has caused much confusion for both creators of artistic works and industrial designs, as there is an uncertainty of whether protection against infringement is afforded under the Copyright Act 1988 (Cth) or whether the Designs Act 2003 (Cth) will apply. In Australia, there is limited precedent that examines the crossover between copyright and designs. Essentially, the cases that have tested this issue remain unclear as to whether a design applied industrially will invoke copyright protection. The cases demonstrate that there is an inconsistency in this area despite the aims of the new provisions of the Designs Act 2003 (Cth) to close the loopholes between copyright and designs. This paper will discuss and evaluate the relationship between copyright protection for artistic works and protection for registered designs with respect to the Designs Act 2003 (Cth).

The Relation between work motivation and project management success in case of temporary organizations : theoretical lenses

The purpose of this paper is to present theoretical lenses that explain the relation between work motivation and project management success in case of temporary organizations such as projects. This paper is a part of the larger research study that first empirically identifies the constructs of work motivation in case of temporary organizations, and then empirically determines the relation between work motivation, and project management success. In the current paper, we have briefly reviewed the theories of work motivation from the work design school. These theories are predominantly drawn from the industrial/ organizational psychology literature. Then, we have considered the recent research on Nine Schools of Project Management as a point of departure to review theory on project management success. These theoretical perspectives are drawn from project management literature. We then illustrate the points of overlap for the theories drawn from these two disciplines. This review helps us to position our research study within the industrial/ organizational psychology, and project management literature as a cross-discipline study.

Joseph Maiden and the national and transnational circulation of Wattle Acacia spp

During the nineteenth century and in the early years of the twentieth century wattle was circulated by botanists, botanical institutions, interested individuals, commercial seedsmen and government authorities. Wattle bark was used in the production of leather and was the subject of debate regarding its commercial development and conservation in Australia. It was also trialled in many other locations including America, New Zealand, Hawaii and Russia. In the process, South Africa became a major producer of wattle bark for a global market. At the same time wattle was also promoted as a symbol of Australian nationalism. This paper considers this movement of wattles, wattle material and wattle information by examining the career of one active agent in these botanical transfers: Joseph Maiden. In doing so it demonstrates that these seemingly different uses of the wattle overlap transnational and national spheres.