Thermally evaporated tungsten oxide (WO3) thin films for gas sensing applications

In this thesis, the author proposed and developed gas sensors made of nanostructured WO3 thin film by a thermal evaporation technique. This technique gives control over film thickness, grain size and purity. The device fabrication, nanostructured material synthesis, characterization and gas sensing performance have been undertaken. Three different types of nanostructured thin films, namely, pure WO3 thin films, iron-doped WO3 thin films by co-evaporation and Fe-implanted WO3 thin films have been synthesized. All the thin films have a film thickness of 300 nm. The physical, chemical and electronic properties of these films have been optimized by annealing heat treatment at 300ºC and 400ºC for 2 hours in air. Various analytical techniques were employed to characterize these films. Atomic Force Microscopy and Transmission Electron Microscopy revealed a very small grain size of the order 5-10 nm in as-deposited WO3 films, and annealing at 300ºC or 400ºC did not result in any significant change in grain size. X-ray diffraction (XRD) analysis revealed a highly amorphous structure of as-deposited films. Annealing at 300ºC for 2 hours in air did not improve crystallinity in these films. However, annealing at 400ºC for 2 hours in air significantly improved the crystallinity in pure and iron-doped WO3 thin films, whereas it only slightly improved the crystallinity of iron-implanted WO3 thin film as a result of implantation. Rutherford backscattered spectroscopy revealed an iron content of 0.5 at.% and 5.5 at.% in iron-doped and iron-implanted WO3 thin films, respectively. The RBS results have been confirmed using energy dispersive x-ray spectroscopy (EDX) during analysis of the films using transmission electron microscopy (TEM). X-ray photoelectron spectroscopy (XPS) revealed significant lowering of W 4f7/2 binding energy in all films annealed at 400ºC as compared with the as-deposited and 300ºC annealed films. Lowering of W 4f7/2 is due to increase in number of oxygen vacancies in the films and is considered highly beneficial for gas sensing. Raman analysis revealed that 400ºC annealed films except the iron-implanted film are highly crystalline with significant number of O-W-O bonds, which was consistent with the XRD results. Additionally, XRD, XPS and Raman analyses showed no evidence of secondary peaks corresponding to compounds of iron due to iron doping or implantation. This provided an understanding that iron was incorporated in the host WO3 matrix rather than as a separate dispersed compound or as catalyst on the surface. WO3 thin film based gas sensors are known to operate efficiently in the temperature range 200ºC-500 ºC. In the present study, by optimizing the physical, chemical and electronic properties through heat treatment and doping, an optimum response to H2, ethanol and CO has been achieved at a low operating temperature of 150ºC. Pure WO3 thin film annealed at 400ºC showed the highest sensitivity towards H2 at 150ºC due to its very small grain size and porosity, coupled with high number of oxygen vacancies, whereas Fe-doped WO3 film annealed at 400ºC showed the highest sensitivity to ethanol at an operating temperature of 150ºC due to its crystallinity, increased number of oxygen vacancies and higher degree of crystal distortions attributed to Fe addition. Pure WO3 films are known to be insensitive to CO, but iron-doped WO3 thin film annealed at 300ºC and 400ºC showed an optimum response to CO at an operating temperature of 150ºC. This result is attributed to lattice distortions produced in WO3 host matrix as a result of iron incorporation as substitutional impurity. However, iron-implanted WO3 thin films did not show any promising response towards the tested gases as the film structure has been damaged due to implantation, and annealing at 300ºC or 400ºC was not sufficient to induce crystallinity in these films. This study has demonstrated enhanced sensing properties of WO3 thin film sensors towards CO at lower operating temperature, which was achieved by optimizing the physical, chemical and electronic properties of the WO3 film through Fe doping and annealing. This study can be further extended to systematically investigate the effects of different Fe concentrations (0.5 at.% to 10 at.%) on the sensing performance of WO3 thin film gas sensors towards CO.

Developing a creative cluster in a post-industrial city : the Creative Industries Development Service (CIDS) and Manchester

This article takes the establishment and demise of Manchester’s Creative Industries Development Service (CIDS) as an exemplary case study for the ways in which creative industry policy has intersected with urban economic policy over the last decade. The authors argue that the creative industries required specific kinds of economic development agencies that would be able to act as “intermediaries” between the distinct languages of policymakers and “creatives.” They discuss the tensions inherent in such an approach and how CIDS attempted to manage them and suggest that the main reason for the demise of the CIDS was the domination of the “economic” over the “cultural” logic, both of which are present within the creative industries policy discourse.

CT and radiographic analysis of sagittal profile changes after thoracoscopic anterior scoliosis surgery

Background. Previous studies report an increase in thoracic kyphosis after anterior approaches and a flattening of sagittal contours following posterior approaches. Difficulties with measuring sagittal parameters on radiographs are avoided with reformatted sagittal CT reconstructions due to the superior endplate clarity afforded by this imaging modality. Methods. A prospective study of 30 Lenke 1 adolescent idiopathic scoliosis (AIS) patients receiving selective thoracoscopic anterior spinal fusion (TASF) was performed. Participants had ethically approved low dose CT scans at minimum 24 months after surgery in addition to their standard care following surgery. The change in sagittal contours on supine CT was compared to standing radiographic measurements of the same patients and with previous studies. Inter-observer variability was assessed as well as whether hypokyphotic and normokyphotic patient groups responded differently to the thoracoscopic anterior approach. Results. Mean T5-12 kyphosis Cobb angle increased by 11.8 degrees and lumbar lordosis increased by 5.9 degrees on standing radiographs two years after surgery. By comparison, CT measurements of kyphosis and lordosis increased by 12.3 degrees and 7.0 degrees respectively. 95% confidence intervals for inter-observer variability of sagittal contour measurements on supine CT ranged between 5-8 degrees. TASF had a slightly greater corrective effect on patients who were hypokyphotic before surgery compared with those who were normokyphotic. Conclusions. Restoration of sagittal profile is an important goal of scoliosis surgery, but reliable measurement with radiographs suffers from poor endplate clarity. TASF significantly improves thoracic kyphosis and lumbar lordosis while preserving proximal and distal junctional alignment in thoracic AIS patients. Supine CT allows greater endplate clarity for sagittal Cobb measurements and linear relationships were found between supine CT and standing radiographic measurements. In this study, improvements in sagittal kyphosis and lordosis following surgery were in agreement with prior anterior surgery studies, and add to the current evidence suggesting that anterior correction is more capable than posterior approaches of addressing the sagittal component of both the instrumented and adjacent non instrumented segments following surgical correction of progressive Lenke 1 idiopathic scoliosis.

Hardness of silicon nitride thin films characterised by nanoindentation and nanoscratch deconvolution methods

Plasma enhanced chemical vapour deposition silicon nitride thin films are widely used in microelectromechanical system devices as structural materials because the mechanical properties of those films can be tailored by adjusting deposition conditions. However, accurate measurement of the mechanical properties, such as hardness, of films with thicknesses at nanometric scale is challenging. In the present study, the hardness of the silicon nitride films deposited on silicon substrate under different deposit conditions was characterised using nanoindentation and nanoscratch deconvolution methods. The hardness values obtained from the two methods were compared. The effect of substrate on the measured results was discussed.

School-aged workers : industrial citizens in waiting?

While the literature points to significant shifts in young peoples’ labour market participation and the social, economic and political context in which this has occurred, it tells us little about whether and in what sense young people can be considered as industrial citizens. We explored the notion of youth citizenship using data derived from 48 focus groups conducted with 216 young people (13-16 years of age) at 19 high schools in Australia. The findings reveal the ways in which several key dimensions of industrial citizenship come to be shaped and have implications for addressing the vulnerability of youth in employment and informing policy and action.

Teaching design and emotion in the foundation year : an industrial design approach

This paper showcases two design tools; the ‘storyboard’ and ‘a day in the life’ demonstrated to design students in their foundational year (first year) of study. By employing these tools during the design process the aim was to provoke students to consider and design for emotional experiences for potential users. The assessment asked students to design an MP3 player using these tools. This is demonstrated through a student project that successfully used the tools and method introduced. The teaching theory, project context, student outcome as well as challenges faced by students using this approach are discussed. The paper concludes with implications for teaching emotion theory at an undergraduate level and potential future directions.

Employment and industrial law in paramedic practice

This chapter will provide you with the some of the information you may need to make information on decisions in cases such as the one given above. In particular it will help you answer questions such as: 1. As Molly and Vikram are approaching the end of their shift, to attend will force them into overtime; could they refuse to attend the job on the basis of the refusal to do overtime outside of contracted hours? 2. Would their refusal be viewed as a breach of contract and therefore a disciplinary issue? 3. Why? 4. Does the need to attend this possibly gravely ill patient outweigh the demands of the paramedics to finish on time?

The Australian screen producer: Understanding screen production cultures in a period of industrial transition [Abstract]

The screen producer plays a vital role in shaping the creative, commercial and entrepreneurial dimensions of production. And yet Australian film history is most often presented as an appreciation of film directors or an examination of industrial governance measures. On the other hand, public funding agencies in Australia have, for the most part, supported independent film and television production as a producer-led, or producer-as-auteur production system, and as such the producer has played a critical role in shaping the broader independent production landscape. In recent years, fundamental changes to distribution and consumption practices have had a major impact on the nature of screen production. Screen producers are increasingly migrating into emerging online, transmedia and cross-media production; generating both opportunities and challenges for traditional producers. However, the production cultures and motivations of producers operating in these emergent spaces remain poorly understood. This presentation will focus on the largely unremarked role of the producer in Australian screen scholarship. It will explore the ways in which the practice of screen producing is evolving and the migratory pathways of traditional producers moving into digital/new media production. The presentation’s primary findings are drawn from the 2011 Australian Screen Producer Survey; a national study of the activities of Australian screen producers conducted by the ARC Centre of Excellence for Creative Industries and Innovation (CCI), Queensland University of Technology, with support from the Centre for Screen Business /Australian Film Television and Radio School (AFTRS). From longitudinal analysis, the presentation will compare and contrast data from the 2009 and 2011 survey across film, television, corporate production and new media industry segments. In so doing the presentation will delineate the practices, attitudes, strategies, and aspirations of screen producers operating in a convergent digital media marketplace and suggest ways forward for a more industrially cognisant approach to screen history.

Conductometric gas sensors based on nanostructured WO3 thin films

Nanostructured WO3 thin films have been prepared by thermal evaporation to detect hydrogen at low temperatures. The influence of heat treatment on the physical, chemical and electronic properties of these films has been investigated. The films were annealed at 400oC for 2 hours in air. AFM and TEM analysis revealed that the as-deposited WO3 film is high amorphous and made up of cluster of particles. Annealing at 400oC for 2 hours in air resulted in very fine grain size of the order of 5 nm and porous structure. GIXRD and Raman analysis revealed that annealing improved the crystallinity of WO3 film. Gas sensors based on annealed WO3 films have shown a high response towards various concentrations (10-10000 ppm) H2 at an operating temperature of 150oC. The improved sensing performance at low operating temperature is due to the optimum physical, chemical and electronic properties achieved in the WO3 film through annealing.

First year industrial design studio-based teaching pedagogies and students’ engagement

Student engagement tends to be viewed as a reflection of learning processes, and in the context of first year university studies, it is a crucial means of an educational process that establishes the foundations for successful later year studies (Krausse and Coates, 2008). In the context of first year design studio teaching in higher education, fostering students’ positive engagement poses challenges to design educators as current trends set these design studios to be large size classes that makes difficult to manage and follow up students’ individual learning experiences. At QUT’s first year industrial design studio classes we engage in a variety of teaching pedagogies from which we identify two of them as instrumental vehicles to foster positive student engagement. Concept bombs and the field trip experience provide such platform as shown in student responses through a learning experience survey.

Dutch tilt, Aussie auteur : the films of Rolf de Heer. 2nd ed.

Dutch-born Australian director, Rolf de Heer, is Australia's most successful and unpredictable film-maker, with thirteen feature films of widely varying style and genre to his name. Arising from the author's 2006 - 2009 PhD research at the Queensland University of Technology (which focussed on the psychoanalytic use of sound in his films), and a fixed term Research Fellowship at the National Film and Sound Archive in Canberra, Australia, "Dutch Tilt, Aussie Auteur: The Films of Rolf de Heer" was first published in 2009 by VDM in Saarbrucken, Germany. This second edition addresses de Heer's additional film-making since 2009, and as with the first edition, is an auteur analysis of the thirteen feature films he has directed (and mostly written and produced). The book explores the theoretical instability of the concept of auteurism and concludes that there is a signature world view to be detected in his oeuvre, and that de Heer (quite possibly unconsciously) promotes unlikely protagonists who are non-hyper masculine, child-like and nurturing, as opposed to the typical Hollywood hero who is macho, exploitative and hyper masculine. Rolf de Heer was born in Heemskerk, Holland, in 1951 and migrated to Australia with his family in 1959. He spent seven years working for the ABC before gaining entry to Australia's Film, Television and Radio School, where he studied Producing and Directing. From his debut feature film after graduating, the children's story about the restoration of a Tiger Moth biplane, "Tail of a Tiger" (1984) to his breakout cult sensation "Bad Boy Bubby" (1993) which "tore Venice [Film Festival] apart" to the first Aboriginal Australian language film "Ten Canoes" (2006) which scooped the pool at the Australian Film Institute awards, de Heer has consistently proven himself unpredictable. This analysis of his widely disparate films, however, suggests that Australia's most innovative film-maker has a signature pre-occupation with giving a voice to marginalised, non-hyper masculine protagonists. Demonstrating a propensity to write and direct in a European-like style, his 'Dutch tilt' is very much not Hollywood, but is nevertheless representative of a typically Aussie world-view.

Managing intensified urban development and industrial uses in Qld : affected area notations

The Queensland government planning policies actively encourage increased dwelling density, sustainable infill development and transit oriented development to maximise land use and minimise urban sprawl. One of the detriments of such a policy is the potential for intensified residential development to create conflict between lawfully operating existing industrial uses and residences. In particular the government is concerned that intensified urban development will increase the risk of litigation from landowners and tenants detrimentally affected by the emission of aerosols, fumes, light, noise, odour, particles or smoke from existing industrial premises.

Efficient route update and maintenance processes for multipath routing in large-scale industrial wireless sensor networks

Reliable communications is one of the major concerns in wireless sensor networks (WSNs). Multipath routing is an effective way to improve communication reliability in WSNs. However, most of existing multipath routing protocols for sensor networks are reactive and require dynamic route discovery. If there are many sensor nodes from a source to a destination, the route discovery process will create a long end-to-end transmission delay, which causes difficulties in some time-critical applications. To overcome this difficulty, the efficient route update and maintenance processes are proposed in this paper. It aims to limit the amount of routing overhead with two-tier routing architecture and introduce the combination of piggyback and trigger update to replace the periodic update process, which is the main source of unnecessary routing overhead. Simulations are carried out to demonstrate the effectiveness of the proposed processes in improvement of total amount of routing overhead over existing popular routing protocols.

Asian representations in films for the Australian Curriculum : an annotated guide

In this annotated guide we offer a reference list, with brief synposes, of possible films for inclusion in schools and linked to the Australian Curriculum: English (AC:E). These films meet one of the three cross curriculum priorities in the Australian Curriculum, which is Studies of Asia, specifically Australia’s contribution to Asia and Asia’s impact on Australia. This priority was recently introduced to curriculum policy in the 2008 Melbourne Declaration (Ministerial Council for Education Early Childhood Development and Youth Affairs, 2008). In this guide we include Australians films made by Asian Australian filmmakers, as well as films about people from Asian countries in Australia, where representations of Asia are a significant part of the film’s content.