Wetting behaviour of silicon nitride ceramics by Ti-Cu alloys

The wetting of Ti-Cu alloys on Si3N4 was analyzed by the sessile drop method, using an imaging system with a CCD camera during the heating under argon flow. The contact angle was measured as a function of temperature and time. The samples were cut transversally and characterized by scanning electron microscopy and energy dispersive spectrometry (SEM/EDS). Wettability of the Ti-Cu alloy on Si3N4 is influenced by the reaction between the Ti and the ceramic. The TC1 and TC2 alloys presented low final contact angle values around 2 degrees and 26 degrees, respectively, indicating good wetting on Si3N4. (c) 2006 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Modification of surface properties of Ti-16Si-4B powder alloy by plasma immersion ion implantation

Results of the surface modification of Ti-16Si-4B powder alloy by nitrogen ion implantation are presented, together with the experimental description of the preparation of that powder by high-energy ball milling and hot pressing. The phase structure, chemical composition and morphology of sample surfaces were observed by utilizing X-ray diffractometer (XRD), atomic force microscope (AFM) and scanning electron microscopy (SEM). A tribological characterization was carried out with a ball-on-disc tribometer and an SEM. Friction coefficient is compared with the one obtained for Ti-6Al-4V alloy and the wear scars characterized by SEM/EDS (energy dispersive spectroscopy). The concentration profile of the detected elements have been investigated using Auger electron spectroscopy (AES) depth profiling. Our results show that a shallow implanted layer of oxygen and nitrogen ions were obtained at the Ti-16Si -4B alloy surface, sufficient to modify slightly its tribological properties. Crown Copyright (C) 2011 Published by Elsevier Ltd. All rights reserved.

Design and Characterization of Novel Wear Resistant Multilayer CVD Coatings with Improved Adhesion Between Al(2)O(3) and Ti(C,N)

Multilayer CVD coatings for high speed cutting applications were designed to achieve high wear and heat resistance during machining of steel alloys. In this work the microstructure and cutting performance of these novel multilayer CVD coatings are investigated and compared with standard CVD multilayer coatings. 3D-FIB tomography is used to characterize the microstructure of the layers, especially the transition between the Ti(C,N) and the Al(2)O(3) layer. The 3D reconstruction of the surface of the Ti(C,N) layer shows the formation of protruded Ti(C,N) grains with a very particular architecture, which penetrate into the Al(2)O(3) top-layer, providing a mechanical anchoring between both layers. Cemented carbides coated with the novel CVD multilayer present reduced crater and flank wear as well as improved adherence between the Al(2)O(3) top-layer and the Ti(C,N) layer leading to a dramatic improvement of cutting performance.

Glass formation of alloys selected by lambda and electronegativity criteria in the Ti-Zr-Fe-Co system

This work evaluates the glass formation of selected alloys based on the Ti-Zr-Fe-Co system, assuming the synergy of two distinct criteria: minimum topological instability and average electronegativity plots. Combining the minimum topological instability and the average electronegativity values result in a plot in which the most probable good glass former compositions are identified Ti-Zr rich alloys with Fe and Co additions were produced, compared against the final plot, and the best glass forming alloy composition was found to be very close the theoretically predicted ones on the Ti-Zr rich side, for both Ti-Zr-Fe and Ti-Zr-Co systems. (C) 2009 Elsevier B V All rights reserved

Hardness and structure characterization of Ti(6)Al(4)V films produced by reactive magnetron sputtering on a conventional austenitic stainless steel

Ti(6)Al(4)V thin films were grown by magnetron sputtering on a conventional austenitic stainless steel. Five deposition conditions varying both the deposition chamber pressure and the plasma power were studied. Highly textured thin films were obtained, their crystallite size (C) 2008 Elsevier Ltd. All rights reserved.

The electrochemical behaviour of Ti-13Nb-13Zr alloy in various solutions

The electrochemical behaviour of a near-beta Ti-13Nb-13Zr alloy for the application as implants was investigated in various solutions. The electrolytes used were 0.9 wt% NaCl solution, Hanks` solution and a culture medium known as minimum essential medium (MEM) composed of salts, vitamins and amino acids, all at 37 degrees C. The electrochemical behaviour was investigated by the following electrochemical techniques: open circuit potential measurements as a function of time, electrochemical impedance spectroscopy (EIS) and determination of polarisation curves. The obtained results showed that the Ti alloy was passive in all electrolytes. The EIS results were analysed using an equivalent electrical circuit representing a duplex structure oxide layer, composed of an inner barrier layer, mainly responsible for the alloy corrosion resistance, and an outer and porous layer that has been associated to osteointegration ability. The properties of both layers were dependent on the electrolyte used. The results suggested that the thickest porous layer is formed in the MEM solution whereas the impedance of the barrier layer formed in this solution was the lowest among the electrolytes used. The polarisation curves showed a current increase at potentials around 1300 mV versus saturated calomel electrode (SCE), and this increase was also dependent on the electrolyte used. The highest increase in current density was also associated to the MEM solution suggesting that this is the most aggressive electrolyte to the Ti alloy among the three tested solutions.

Effect of Ti and C additions on structural and magnetic properties of (Pr,Nd)-Fe-B nanocrystalline magnetic materials

Effects of titanium carbide (TiC) addition on structural and magnetic properties of isotropic (Pr,Nd)-Fe-B nanocrystalline magnetic materials have been investigated. In this work, we investigate the effect of TiC addition on a (Pr,Nd)-poor and B-rich composition, as well as on a B-poor and (Nd, Pr)-rich composition. Rapidly solidified (Pr, Nd)-Fe-B alloys were prepared by melt-spinning. The compositions studied were (Pr(1-x)Nd(x))(4)Fe(78)B(18) (x = 0, 0.5, and 1) with addition of 3 at% TiC. Unlike the (Pr(x)Nd(1-x))(9.5)Fe(84.5)B(6) materials that present excellent values for coercive. field and energy product, the (Pr,Nd)-poor and B-rich composition alloys with TiC addition present lower values. Rietveld analysis of X-ray data and Mossbauer spectroscopy revealed that samples are predominantly composed of Fe(3)B and alpha-Fe. For the RE-rich compositions (Pr(x)Nd(1-x))(9.5)Fe(84.5)B(6) (x = 0.1, 0.25, 0.5, 0.75, and 1) with the addition of 3 at% TiC, the highest coercive field and energy product (8.4 kOe and 14.4 MGOe, respectively) were obtained for the composition Pr(9.5)Fe(84.5)B(6). (c) 2008 Elsevier B.V. All rights reserved.

Oxidation of toluene in waste gas streams using mesoporous Ti-hexagonal mesoporous silica

Various mesoporous catalysts with titanium loadings between 0.5 and 4 Ti wt. % and surface areas between 600 and 1,600 m(2)/g were synthesized using the molecular designed dispersion technique. These catalysts were tested using toluene oxidation in a fixed bed reactor at temperatures between 300 and 550degreesC. The reaction products were found to be CO2 and CO with selectivity towards CO2 above 80% for all catalysts. The catalytic activity of the catalysts increases with titanium loading. The total conversion at 550degreesC was not affected by the textural porosity, but increased textural porosity did significantly reduce the ignition temperature by up to 50degreesC. The Thiele modulus was calculated to be much less than one for all these materials indicating that the reaction rate is not diffusion, limited.

Application of Ti/RuO(2)-Ta(2)O(5) electrodes in the electrooxidation of ethanol and derivants: Reactivity versus electrocatalytic efficiency

The influence of the preparation method on the performance of RuO(2)-Ta(2)O(5) electrodes was evaluated toward the ethanol oxidation reaction (EOR). Freshly prepared RuO(2)-Ta(2)O(5) thin films containing between 30 and 80 at.% Ru were prepared by two different methods: the modified Pechini-Adams method (DPP) and standard thermal decomposition (STD). Electrochemical investigation of the electrode containing RuO(2)-Ta(2)O(5) thin films was conducted as a function of electrode composition in a 0.5-mol dm(-3) H(2)SO(4) solution, in the presence and absence of ethanol and its derivants (acetaldehyde and acetic acid). At a low ethanol concentration (5 mmol dm(-3)), ethanol oxidation leads to high yields of acetic acid and CO(2). On the other hand, an increase in ethanol concentration (15-1000 mmol dm(-3)) favors acetaldehyde formation, so acetic acid and CO(2) production is hindered, in this case. Electrodes prepared by DPP provide higher current efficiency than STD electrodes for all the investigated ethanol concentrations. This may be explained by the increase in electrode area obtained with the DPP preparation method compared with STD. (c) 2008 Elsevier Ltd. All rights reserved.

Effect of argon purity on mechanical properties, microstructure and fracture mode of commercially pure (cp) Ti and Ti-6Al-4V alloys for ceramometal dental prostheses

Provision of an inert gas atmosphere with high-purity argon gas is recommended for preventing titanium castings from contamination although the effects of the level of argon purity on the mechanical properties and the clinical performance of Ti castings have not yet been investigated. The purpose of this study was to evaluate the effect of argon purity on the mechanical properties and microstructure of commercially pure (cp) Ti and Ti-6Al-4V alloys. The castings were made using either high-purity and/or industrial argon gas. The ultimate tensile strength (UTS), proportional limit (PL), elongation (EL) and microhardness (VHN) at different depths were evaluated. The microstructure of the alloys was also revealed and the fracture mode was analyzed by scanning electron microscopy. The data from the mechanical tests and hardness were subjected to a two-and three-way ANOVA and Tukey`s test (alpha = 0.05). The mean values of mechanical properties were not affected by the argon gas purity. Higher UTS, PL and VHN, and lower EL were observed for Ti-6Al-4V. The microhardness was not influenced by the argon gas purity. The industrial argon gas can be used to cast cp Ti and Ti-6Al-4V.

Modelo de gest??o do ambiente de TI aplicado ao IBGE

A arquitetura de inform??tica do IBGE busca refletir a evolu????o das Tecnologias da Informa????o e de Comunica????o (TIC) e vem sendo modificada ao longo dos anos, de maneira a manter - se um equil??brio entre os anseios e diretrizes institucionais e governamentais. A partir do aprendizado e do sucesso obtidos no Censo Demogr??fico 2010, o IBGE inova agora na forma de administrar sua ??rea de TIC, baseado em software especialista adquirido.O IBGE se beneficia da administra????o dos bens de inform??tica, da responsabilidade sobre contratos, da gest??o do patrim??nio, do uso otimizado dos softwares comerciais, da agilidade de obten????o de informa????es sobre o parque computacional instalado, do monitoramento on-line dos servi??os oferecidos pela TI, da economia de gastos com viagens para suporte t??cnico dentro dos estados e entre os mesmos, da reeduca????o de funcion??rios quanto ao uso de tecnologias, da forma organizada e planejada de trabalho e, portanto, da gest??o p??blica das TIC

Almoxarifado virtual: uma proposta de sustentabilidade por contrata????o de gerenciamento de meios

A iniciativa opera a partir da presta????o de um servi??o continuado de gerenciamento de meios. Em s??ntese, o ??rg??o parou de adquirir materiais de escrit??rio e de combate a inc??ndio e passou a operar com um almoxarifado terceirizado que fornece insumos de expediente, processamento de dados e combate a inc??ndios de seu pr??prio almoxarifado, num sistema similar a um stop shop, al??m de controlar os estoques de pronto uso de cada unidade e fazer o seu ressuprimento. Cada unidade da autarquia possui uma cota aut??noma de pedidos, num baixo valor em periodicidade mensal. Com tal iniciativa, as unidades se mant??m supridas o ano todo, sem desperd??cios e sem estoques, fazendo os seus pedidos no almoxarifado virtual e customizando suas cestas de necessidades de produtos para a produ????o processual e o atendimento sazonal das emerg??ncias ambientais

Sistema Nacional de Gest??o do Conhecimento em Seguran??a P??blica

Visando subsidiar o processo de gest??o do Sistema ??nico de Seguran??a P??blica, a Secretaria Nacional de Seguran??a P??blica (Senasp) investe esfor??os, desde 2003, na cria????o de sistemas nacionais de coleta de dados, na moderniza????o da infraestrutura de TI e na qualifica????o dos profissionais para a produ????o desses dados e o desenvolvimento de insumos, a fim de auxiliar na distribui????o de recursos do Fundo Nacional de Seguran??a P??blica. Todas essas iniciativas comp??em o Sistema Nacional de Gest??o do Conhecimento em Seguran??a P??blica. Em parceria com profissionais e pesquisadores da ??rea e gestores de outros ??rg??os p??blicos, foi estruturada uma nova forma de fazer seguran??a p??blica. As a????es come??aram a ser baseadas em diagn??sticos; a distribui????o de recursos passou a obedecer um sistema de incentivos calcado em indicadores estat??sticos, fundamentais na constru????o do conhecimento necess??rio para aprimorar a efici??ncia, a efic??cia e a efetividade das pol??ticas de seguran??a. Paralelamente, procurou-se difundir a cultura da transpar??ncia e divulga????o de estat??sticas criminais

As enchentes em Santa Catarina e o aprendizado em pol??ticas p??blicas

O estudo de caso aborda o gerenciamento das crises decorrentes do fen??meno das inunda????es no Vale do Itaja??, em Santa Catarina. Na narrativa apresentada, h?? informa????es sobre a evolu????o da ocupa????o do territ??rio e os respectivos desdobramentos na din??mica ambiental, com ??nfase nas a????es que o setor p??blico adotou para enfrentar os desastres. Os eventos clim??ticos ocorridos em 2008 e 2011 s??o detalhados, com o objetivo de caracterizar a preven????o e a capacidade de resposta que o governo e a sociedade demonstraram

O gerenciamento contratual aplicado no ??mbito das contrata????es do Poder Judici??rio de Alagoas

O estudo de caso trata de mudan??as na estrutura de gest??o dos contratos administrativos do Tribunal de Justi??a de Alagoas. Com a finalidade de minimizar o desperd??cio de recursos p??blicos e conferir mais transpar??ncia ?? fiscaliza????o de contratos, o ??rg??o decidiu inserir uma unidade de gest??o contratual entre a figura do fiscal do contrato e o ordenador de despesa. O caso ilustra uma melhoria na forma de gest??o de contratos administrativos e pode ser utilizado em cursos de gest??o de contratos, licita????o e temas afins para an??lise de experi??ncia bem-sucedida de mudan??a organizacional focada na gest??o contratual