Field Evaluation of Alternative Load Transfer Device Locations in Low Traffic Volume Pavements, TR-420, 2003

In jointed portland cement concrete pavements, dowel bars are typically used to transfer loads between adjacent slabs. A common practice is for designers to place dowel bars at a certain, consistent spacing such that a sufficient number of dowels are available to effectively transfer anticipated loads. In many cases, however, the standards developed today for new highway construction simply do not reflect the design needs of low traffic volume, rural roads. The objective of this research was to evaluate the impact of the number of dowel bars and dowel location on joint performance and ultimately on pavement performance. For this research, test sections were designed, constructed, and tested in actual field service pavement. Test sections were developed to include areas with load transfer assemblies having three and four dowels in the outer wheel path only, areas with no joint reinforcement whatsoever, and full lane dowel basket assemblies as the control. Two adjacent paving projects provided both rural and urban settings and differing base materials. This report documents the approach to implementing the study and provides discussion and suggestions based on the results of the research. The research results indicate that the use of single three or four dowel basket assemblies in the outer wheel path is acceptable for use in low truck volume roads. In the case of roadways with relatively stiff bases such as asphalt treated or stabilized bases, the use of the three dowel bar pattern in the outside wheel path is expected to provide adequate performance over the design life of the pavement. In the case of untreated or granular bases, the results indicate that the use of the three or four dowel bar basket in both wheel paths provides the best long-term solution to load transfer and faulting measurements.

Development of LRFD Design Procedures for Bridge Piles in Iowa – Field Testing of Steel H-Piles in Clay, Sand, and Mixed Soils and Data Analysis (Volume II), TR-583, 2011

In response to the mandate on Load and Resistance Factor Design (LRFD) implementations by the Federal Highway Administration (FHWA) on all new bridge projects initiated after October 1, 2007, the Iowa Highway Research Board (IHRB) sponsored these research projects to develop regional LRFD recommendations. The LRFD development was performed using the Iowa Department of Transportation (DOT) Pile Load Test database (PILOT). To increase the data points for LRFD development, develop LRFD recommendations for dynamic methods, and validate the results of LRFD calibration, 10 full-scale field tests on the most commonly used steel H-piles (e.g., HP 10 x 42) were conducted throughout Iowa. Detailed in situ soil investigations were carried out, push-in pressure cells were installed, and laboratory soil tests were performed. Pile responses during driving, at the end of driving (EOD), and at re-strikes were monitored using the Pile Driving Analyzer (PDA), following with the CAse Pile Wave Analysis Program (CAPWAP) analysis. The hammer blow counts were recorded for Wave Equation Analysis Program (WEAP) and dynamic formulas. Static load tests (SLTs) were performed and the pile capacities were determined based on the Davisson’s criteria. The extensive experimental research studies generated important data for analytical and computational investigations. The SLT measured load-displacements were compared with the simulated results obtained using a model of the TZPILE program and using the modified borehole shear test method. Two analytical pile setup quantification methods, in terms of soil properties, were developed and validated. A new calibration procedure was developed to incorporate pile setup into LRFD.

Personality and personality disorders in urban and rural Africa: results from a field trial in Burkina Faso

When conducting research in different cultural settings, assessing measurement equivalence is of prime importance to determine if constructs and scores can be compared across groups. Structural equivalence implies that constructs have the same meaning across groups, metric equivalence implies that the metric of the scales remains stable across groups, and full scale or scalar equivalence implies that the origin of the scales is the same across groups. Several studies have observed that the structure underlying both normal personality and personality disorders (PDs) is stable across cultures. Most of this cross-cultural research was conducted in Western and Asian cultures. In Africa, the few studies were conducted with well-educated participants using French or English instruments. No research was conducted in Africa with less privileged or preliterate samples. The aim of this research was to study the structure and expression of normal and abnormal personality in an urban and a rural sample in Burkina Faso. The sample included 1,750 participants, with a sub-sample from the urban area of Ouagadougou (n = 1,249) and another sub-sample from a rural village, Soumiaga (n = 501). Most participants answered an interview consisting of a Mooré language adaptation of the Revised NEO Personality Inventory and of the International Personality Disorders Examination. Mooré is the language of the Mossi ethnic group, and the most frequently spoken local language in Burkina Faso. A sub-sample completed the same self-report instruments in French. Demographic variables only had a small impact on normal and abnormal personality traits mean levels. The structure underlying normal personality was unstable across regions and languages, illustrating that translating a complex psychological inventory into a native African language is a very difficult task. The structure underlying abnormal personality and the metric of PDs scales were stable across regions. As scalar equivalence was not reached, mean differences cannot be interpreted. Nevertheless, these differences could be due to an exaggerated expression of abnormal traits valued in the two cultural settings. Our results suggest that studies using a different methodology should be conducted to understand what is considered, in different cultures, as deviating from the expectations of the individual's culture, and as a significant impairment in self and interpersonal functioning, as defined by the DSM-5.

Ultimate Load Behavior of Full-Scale Highway Truss Bridges: Phase I - Ultimate Load Tests of the Hubby Bridge - Boone County, Interim Report, HR-169, 1975

As a result of the construction of the Saylorville Dam and Reservoir on the Des Moines River, six highway bridges crossing the river were scheduled for removal. One of these, an old pinconnected high-truss single-lane bridge, was selected for a testing program which included ultimate load tests. The purpose of the ultimate load tests, which are summarized in this report, was to relate design and rating procedures presently used in bridge design to the field behavior of this type of truss bridge. The ultimate load tests consisted of ultimate load testing of one span of the bridge, of two I-shaped floorbeams, and of two panels of the timber deck. The theoretical capacity of each of these components is compared with the results from the field tests.

Ultimate Load Behavior of Full-Scale Highway Truss Bridges: Phase II - Service Load and Supplementary Tests, Interim Report, HR-169, 1975

As a result of the construction of the Saylorville Dam and Reservoir on the Des Moines River, six highway bridges crossing the river were scheduled for removal. Two of these were incorporated into a comprehensive test program to study the behavior of old pin-connected high-truss single-lane bridges. The test program consisted of ultimate load tests, service load tests and a supplementary test program. The results reported in this report cover the service load tests on the two bridges as well as the supplementary tests, both static and fatigue, of eyebar members removed from the two bridges. The field test results of the service loading are compared with theoretical results of the truss analysis.

Protein oligomers studied by solid-state NMR the case of the full-length nucleoid-associated protein histone-like nucleoid structuring protein

Members of the histone-like nucleoid structuring protein (H-NS) family play roles both as architectural proteins and as modulators of gene expression in Gram-negative bacteria. The H-NS protein participates in modulatory processes that respond to environmental changes in osmolarity, pH, or temperature. H-NS oligomerization is essential for its activity. Structural models of different truncated forms are available. However, high-resolution structural details of full-length H-NS and its DNA-bound state have largely remained elusive. We report on progress in characterizing the biologically active H-NS oligomers with solid-state NMR. We compared uniformly ((13)C,(15)N)-labeled ssNMR preparations of the isolated N-terminal region (H-NS 1-47) and full-length H-NS (H-NS 1-137). In both cases, we obtained ssNMR spectra of good quality and characteristic of well-folded proteins. Analysis of the results of 2D and 3D (13)C-(13)C and (15)N-(13)C correlation experiments conducted at high magnetic field led to assignments of residues located in different topological regions of the free full-length H-NS. These findings confirm that the structure of the N-terminal dimerization domain is conserved in the oligomeric full-length protein. Small changes in the dimerization interface suggested by localized chemical shift variations between solution and solid-state spectra may be relevant for DNA recoginition.

Full-Body MRI in Patients With an Implantable Cardioverter-Defibrillator: Primary Results of a Randomized Study.

BACKGROUND: Magnetic resonance imaging (MRI) of patients with conventional implantable cardioverter-defibrillators (ICD) is contraindicated. OBJECTIVES: This multicenter, randomized trial evaluated safety and efficacy of a novel ICD system specially designed for full-body MRI without restrictions on heart rate or pacing dependency. The primary safety objective was >90% freedom from MRI-related events composite endpoint within 30 days post-MRI. The primary efficacy endpoints were ventricular pacing capture threshold and ventricular sensing amplitude. METHODS: Subjects received either a single- or dual-chamber ICD. In a 2:1 randomization, subjects either underwent MRI at 1.5-T of the chest, cervical, and head regions to maximize radiofrequency exposure up to 2 W/kg specific absorption rate and gradient field exposure to 200 T/m/s per axis (MRI group, n = 175), or they underwent a 1-h waiting period without MRI (control group, n = 88). A subset of MRI patients underwent ventricular fibrillation induction testing post-MRI to characterize defibrillation function. RESULTS: In 42 centers, 275 patients were enrolled (76% male, age 60.4 ± 13.8 years). The safety endpoint was met with 100% freedom from the composite endpoint (p < 0.0001). Both efficacy endpoints were met with minimal differences in the proportion of MRI and control patients who demonstrated a ≤0.5 V increase in ventricular pacing capture threshold (100% MRI vs. 98.8% control, noninferiority p < 0.0001) or a ≤50% decrease in R-wave amplitude (99.3% MRI vs. 98.8% control, noninferiority p = 0.0001). A total of 34 ventricular tachyarrhythmia/ventricular fibrillation episodes (20 induced; 14 spontaneous) occurred in 24 subjects post-MRI, with no observed effect on sensing, detection, or treatment. CONCLUSIONS: This is the first randomized clinical study of an ICD system designed for full-body MRI at 1.5-T. These data support that the system is safe and the MRI scan does not adversely affect electrical performance or efficacy. (Confirmatory Clinical Trial of the Evera MRI System for Conditionally-Safe MRI Access; NCT02117414).

The ESRg matrix for strong field d5 systems

This review has tried to collect and correlate all the various equations for the g matrix of strong field d5 systems obtained from different basis sets using full electron and hole formalism calculations. It has corrected mistakes found in the literature and shown how the failure to properly take in symmetry boundary conditions has produced a variety of apparently inconsistent equations in the literature. The review has reexamined the problem of spin-orbit interaction with excited t4e states and finds that the earlier reports that it is zero in octahedral symmetry is not correct. It has shown how redefining what x, y, and z are in the principal coordinate system simplifies, compared to previous methods, the analysis of experimental g values with the equations.

Monolithic zirconium dioxide as a full contour restorative material: With special emphasis on the optical and mechanical properties

Full contour monolithic zirconia restorations have shown an increased popularity in the dental field over the recent years, owing to its mechanical and acceptable optical properties. However, many features of the restoration are yet to be researched and supported by clinical studies to confirm its place among the other indirect restorative materials This series of in vitro studies aimed at evaluating and comparing the optical and mechanical properties, light cure irradiance, and cement polymerization of multiple monolithic zirconia material at variable thicknesses, environments, treatments, and stabilization. Five different monolithic zirconia materials, four of which were partially stabilized and one fully stabilized were investigated. The optical properties in terms of surface gloss, translucency parameter, and contrast ratio were determined via a reflection spectrophotometer at variable thicknesses, coloring, sintering method, and after immersion in an acidic environment. Light cure irradiance and radiant exposure were quantified through the specimens at variable thicknesses and the degree of conversion of two dual-cure cements was determined via Fourier Transform Infrared spectroscopy. Bi-axial flexural strength was evaluated to compare between the partially and fully stabilized zirconia prepared using different coloring and sintering methods. Surface characterization was performed using a scanning electron microscope and a spinning disk confocal microscope. The surface gloss and translucency of the zirconia investigated were brand and thickness dependent with the translucency values decreasing as the thickness increased. Staining decreased the translucency of the zirconia and enhanced surface gloss as well as the flexural strength of the fully stabilized zirconia but had no effect on partially stabilized zirconia. Immersion in a corrosive acid increased surface gloss and decreased the translucency of some zirconia brands. Zirconia thickness was inversely related to the amount of light irradiance, radiant exposure, and degree of monomer conversion. Type of sintering furnace had no effect on the optical and mechanical properties of zirconia. Monolithic zirconia maybe classified as a semi-translucent material that is well influenced by the thickness, limiting its use in the esthetic zones. Conventional acid-base reaction, autopolymerizing and dual-cure cements are recommended for its cementation. Its desirable mechanical properties give it a high potential as a restoration for posterior teeth. However, close monitoring with controlled clinical studies must be determined before any definite clinical recommendations can be drawn.

Body size in the field cricket Gryllus integer (Orthoptera : Gryllidae) :heritability and male mating success

The influence of male body weight on the aggressive and mating behaviour of male Gryllus integer was studied under laboratory conditions. The relationship between adult age and weight was first determined; female weight increased and male weight decreased with age. Virgin males that had been isolated since the adult molt were paired for similar age and a difference in weight of greater than 200 mg. Paired males and a virgin female were observed in a glass arena for 24 minutes or until a mating occurred. Larger males mated significantly more often than smaller males. Larger males attacked more often, were more successful in aggressive encounters and had more contact with the female. Males that did not mate had lower rates of courtship and mounts than males that mated. Females in trials that did not result in a mating were signifcantly heavier than females in trials that resulted in a mating. Larger males that mated were significantly closer in weight to the weight of the female than larger males in trials that did not result in a mating. Larger males in trials that did not result in a mating had higher rates of aggressive stridulation than larger males that mated. Male weight is therefore important in mating success; fitness traits should theoretically show low genetic variability. However, significant heritability values were found for live weight, dry weight, head width, pronotum width and length, hind femur length and forewing length when estimated from the regression of offspring on mid-parent values, offspring and female and male values separately and full-sib correlations. The heritability of hind femur width was significant when estimated from the regression of offspring on male parent and from full-sib correlations. Heritability estimates of forewing length were significantly higher when estimated from the regression of offspring on female parent than when estimated from the regression of offspring on male parent. High phenotypic, genetic and environmental correlations were found between all pairs of traits. Data on male mating success and the heritability of fitness traits were discussed in terms of the maintenance of genetic variability.

What Matters? : the full-time graduate students' perceptions of teacher effectiveness

The purpose of this qualitative study was to explore the full-time graduate students' perceptions of teacher effectiveness at the graduate school level, to identify how graduate students perceive effective and ineffective teachers, and specifically to discover the main dimensions of teacher effectiveness that graduate students perceive as most significant. This topic was investigated because, although the teacher has been deemed as a crucial component in the teaching process, there is no common agreement on the definition and measure of teacher effectiveness. Graduate students' perceptions of teacher effectiveness have not been given much attention. The research design was based on a ground theory approach. It utilized qualitative data through interviews, field notes, andjournals. The findings ofthis study revealed that teacher effectiveness is markedly influential to graduate students. There is no universally consented definition or measure of teacher effectiveness due to the multidimensionality of teaching and learning. Nevertheless, several major dimensions ofteacher effectiveness were discovered and highlighted in this study. Such dimensions include good command of subject matter, presentation skills, challenging and motivating students, rapport with students, learning environment, course demands, as well as assessment and feedback. It was hoped that the study would move towards developing a theory that contributes to the knowledge base of graduate students' perceptions of teacher effectiveness. It was anticipated that the results would provide first-hand information for the instructor to improve teaching; for the administrator to promote the effective educational experiences and student achievements. It was intended that the findings would lay a theoretical and empirical groundwork for future research.

A field study of factors influencing the concentrations of a traffic-related pollutant in the vicinity of a complex urban junction

The paper describes a field study focused on the dispersion of a traffic-related pollutant within an area close to a busy intersection between two street canyons in Central London. Simultaneous measurements of airflow, traffic flow and carbon monoxide concentrations ([CO]) are used to explore the causes of spatial variability in [CO] over a full range of background wind directions. Depending on the roof-top wind direction, evidence of both flow channelling and recirculation regimes were identified from data collected within the main canyon and the intersection. However, at the intersection, the merging of channelled flows from the canyons increased the flow complexity and turbulence intensity. These features, coupled with the close proximity of nearby queuing traffic in several directions, led to the highest overall time-average measured [CO] occurring at the intersection. Within the main street canyon, the data supported the presence of a helical flow regime for oblique roof-top flows, leading to increased [CO] on the canyon leeward side. Predominant wind directions led to some locations having significantly higher diurnal average [CO] due to being mostly on the canyon leeward side during the study period. For all locations, small changes in the background wind direction could cause large changes in the in-street mean wind angle and local turbulence intensity, implying that dispersion mechanisms would be highly sensitive to small changes in above roof flows. During peak traffic flow periods, concentrations within parallel side streets were approximately four times lower than within the main canyon and intersection which has implications for controlling personal exposure. Overall, the results illustrate that pollutant concentrations can be highly spatially variable over even short distances within complex urban geometries, and that synoptic wind patterns, traffic queue location and building topologies all play a role in determining where pollutant hot spots occur.

Influence of agricultural management, sward structure and food resources on grassland field use by birds in lowland England.

Agricultural management of grassland in lowland Britain has changed fundamentally in the last 50 years, resulting in spatial and structural uniformity within the pastoral landscape. The full extent to which these changes may have reduced the suitability of grassland as foraging habitat for birds is unknown. This study investigated the mechanisms by which these changes have impacted on birds and their food supplies. We quantified field use by birds in summer and winter in two grassland areas of lowland England (Devon and Buckinghamshire) over 3 years, relating bird occurrence to the management, sward structure and seed and invertebrate food resources of individual fields. Management intensity was defined in terms of annual nitrogen input. There was no consistent effect of management intensity on total seed head production, although those of grasses generally increased with inputs while forbs were rare throughout. Relationships between management intensity and abundance of soil and epigeal invertebrates were complex. Soil beetle larvae were consistently lower in abundance, and surface-active beetle larvae counts consistently higher, in intensively managed fields. Foliar invertebrates showed more consistent negatively relationships with management intensity. Most bird species occurred at low densities. There were consistent relationships across regions and years between the occurrence of birds and measures of field management. In winter, there was a tendency towards higher occupancy of intensively managed fields by species feeding on soil invertebrates. In summer, there were few such relationships, although many species avoided fields with tall swards. Use of fields by birds was generally not related to measures of seed or invertebrate food abundance. While granivorous species were perhaps too rare to detect a relationship, in insectivores the strong negative relationships (in summer) with sward height suggested that access to food may be the critical factor. While it appears that intensification of grassland management has been deleterious to the summer food resources of insectivorous birds that use insects living within the grass sward, intensification may have been beneficial to several species in winter through the enhancement of soil invertebrates. Synthesis and applications. We suggest that attempts to restore habitat quality for birds in grassland landscapes need to create a range of management intensities and sward structures at the field and farm scales. A greater understanding of methods to enhance prey accessibility, as well as abundance, for insectivorous birds is required.

Economic analysis of integrated weed management in field bean (Phaseolus vulgaris L.)

Field experiments were conducted in field bean in the north-eastern part of the Republic of Croatia to compare weed control and crop response under different management practices within the critical period of field bean production. The practices consisted in broadcast application of labelled rate of preemergence herbicide (PRE) and postemergence herbicide application: (POST) broadcast, band application over the rows, and band application combined with mechanical cultivation using of different herbicide doses recommended by the manufacturer (2x, 1x, 1/2x, 1/4x, 1/8x). In 1999, weed control with PRE application of pendimethalin was superior to POST bentazone application due to late emergence of weeds and lack of residual herbicide control. In 2000 bentazone combined with cycloxydim controlled weeds in field bean better than PRE herbicide application. Based on the results of this research, single PRE or POST application of herbicide did not control a broad spectrum of weeds and did not provide the commercially acceptable full season control. Reduced rates of herbicide are not advisable tinder high weed pressure.

Establishing field margins to promote beetle conservation in arable farms

This study investigates the function of non-cropped field margins in arable farming systems for enhancing the biodiversity value of beetle communities. Three different sown seed mixtures were used to establish field margins, a Countryside Stewardship mix, a fine grass and forbs mix and a tussock grass and forbs mix. The structure of beetle communities in the first full year of establishment was found to show no difference between the tussock grass and Countryside Stewardship margins. However, both differed from the fine grass margins, which supported lower overall abundance and species richness of beetles. This was attributed to small-scale architectural differences between species of fine and tussock grasses, rather than differences in plant composition. Body size distributions of beetles showed distinct similarities between the Countryside Stewardship and tussock margins. A greater abundance of large beetles was found in fine grass margins, although in all cases these body size distributions were attributed to a small number of species or a taxonomically distinct group. All three margin types included beetle species of conservation value. The importance of these results was discussed in the context of the value of these seed mixtures for invertebrate conversation. (c) 2004 Elsevier B.V. All rights reserved.