Surface characterization of feldspathic ceramic using ATR FT-IR and ellipsometry after various silanization protocols

Objectives. This study characterized the feldspathic ceramic surfaces after various silanization protocols.Methods. Ceramic bars (2 mm x 4 mm x 10 mm) (N = 18) of feldpathic ceramic (VM7, VITA Zahnfabrik) were manufactured and finished. Before silane application, the specimens were ultrasonically cleaned in distilled water for 10 min. The ceramic specimens were randomly divided into nine groups (N = 2 per group) and were treated with different silane protocols. MPS silane (ESPE-Sil, 3M ESPE) was applied to all specimens and left to react at 20 degrees C for 2 min (G20). After drying, the specimens were subjected to heat treatment in an oven at 38 degrees C (G38), 79 degrees C (G79) or 100 degrees C (G100) for 1 min. Half of the specimens of each group were rinsed with water at 80 degrees C for 15 s (G20B, G38B, G79B, G100B). The control group (GC) received no silane. Attenuated total reflection infrared Fourier transform analysis (ATR FT-IR) was performed using a spectrometer. Thickness of silane layer was measured using a spectroscopic ellip-someter working in the lambda = 632.8 nm (He-Ne laser) at 70 degrees incidence angle. Surface roughness was evaluated using an optical profilometer. Specimens were further analyzed under the Scanning Electron Microscopy (SEM) to observe the topographic patterns.Results. ATR FT-IR analysis showed changes in Si-O peaks with enlarged bands around 940 cm(-1). Ellipsometry measurements showed that all post-heat treatment actions reduced the silane film thickness (30.8-33.5 nm) compared to G20 (40 nm). The groups submitted to rinsing in hot water (B groups) showed thinner silane films (9.8-14.4 nm) than those of their corresponding groups (without washing) (30.8-40 nm). Profilometer analysis showed that heat treatments (Ra approximate to 0.10-0.19 mu m; Rq approximate to 0.15-0.26 mu m) provided a smoother surface than the control group (Ra approximate to 0.48 mu m; Rq approximate to 0.65 mu m). Similar patterns were also observed in SEM images.Significance. Heat treatment after MPS silane application improved the silane layer network. Rinsing with boiling water eliminated the outmost unreacted regions of the silane yielding to thinner film thicknesses. (C) 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Intense photoluminescence emission at room temperature in calcium copper titanate powders

A study was undertaken about the structural and photoluminescent properties at room temperature of CaCu3Ti4O12 (CCTO) powders synthesized by a soft chemical method and heat treated between 300 and 800 °C. The decomposition of precursor powder was followed by thermogravimetric analysis (TG-DTA), X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Fourier transform Raman (FT-Raman) and photoluminescence (PL) measurements. XRD analyses revealed that the powders annealed at 800 °C are becoming ordered and crystallize in the cubic structure. The most intense PL emission was obtained for the sample calcined at 700 °C, which is not highly disordered (300-500 °C) and neither completely ordered (800 °C). From the spectrum it is clearly visible that the lowest wavelength peak is placed around 480 nm and the highest wavelength peak at about 590 nm. The UV/vis absorption spectroscopy measurements showed the presence of intermediate energy levels in the band gap of structurally disordered powders. © 2012 Elsevier Ltd and Techna Group S.r.l.

Estudo de transições durante o processo de desenovelamento térmico da RNase A por meio da calorimetria (DSC) e espectroscopia de correlação bidimensional no infravermelho médio (2D-IR)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Potencial biossotivo e biodegradativo da Saccharomyces cerevisiae imobilizada em alginato de cálcio e em células livres na remoção de corantes têxteis de efluente

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da temperatura e do tipo de substrato em filmes de GaN depositados por magnetron sputtering reativo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modificação superficial de nanopartículas de óxido de ferro por poli(ácido aspártico) reticulado

Pós-graduação em Química - IQ

Paleometry: a brand new area in brazilian science

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Síntese e caracterização de complexos de lantanídeos pesados e ítrio(III) como o fármaco ibuprofeno no estado sólido

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Scaffold nanoestruturado utilizando-se celulose bacteriana/fosfatos de cálcio para regeneração óssea

Pós-graduação em Biotecnologia - IQ

Iron(III) Porphyrin Covalently Supported onto Magnetic Amino-Functionalized Nanospheres as Catalyst for Hydrocarbon and Herbicide Oxidations

This work describes the covalent immobilization of an ironporphyrin, 5,10,15,20-tetrakis(pentafluorophenyl)porphyrin iron(III) chloride (FeTFPP), onto maghemite/silica magnetic nanospheres covered with aminofunctionalized silica. The resulting material (gamma-Fe2O3/SiO2-NHFeP) was characterized by diffuse reflectance infrared spectroscopy (DRIFTS) and UV-Vis absorption spectroscopy. The catalytic activity of this magnetic ironporphyrin was investigated in the oxidation of hydrocarbons (styrene, (Z)-cyclooctene and R-(+)-limonene) and an herbicide (simazine) by hydrogen peroxide or 3-chloroperoxybenzoic acid. Hydrocarbon and simazine oxidation reaction products were analyzed by gas chromatography (GC) and high performance liquid chromatography (HPLC), respectively. This catalytic system proved to be efficient and selective for hydrocarbon oxidation, leading to high product yields from styrene (89%), cyclooctene (71%) and R-(+) -limonene (86%). Simazine oxidation was attained with 100% selectivity for a dechlorinated product (OEAT), while several oxidation products were obtained for the same catalyst in homogeneous media. The catalyst can be easily recovered through application of an external magnetic field and washed after reaction. Catalyst reuse experiments for R-(+)-limonene oxidation have shown that the catalytic activity is kept at 90% after 10 consecutive reactions.

Iron(III) porphyrin covalently supported onto magnetic amino-functionalized nanospheres as catalyst for hydrocarbon and herbicide oxidations

This work describes the covalent immobilization of an ironporphyrin, 5,10,15,20- tetrakis(pentafluorophenyl)porphyrin iron(III) chloride (FeTFPP), onto maghemite/silica magnetic nanospheres covered with aminofunctionalized silica. The resulting material (γ-Fe2O3/SiO2-NHFeP) was characterized by diffuse reflectance infrared spectroscopy (DRIFTS) and UV-Vis absorption spectroscopy. The catalytic activity of this magnetic ironporphyrin was investigated in the oxidation of hydrocarbons (styrene, (Z)-cyclooctene and R-(+)-limonene) and an herbicide (simazine) by hydrogen peroxide or 3-chloroperoxybenzoic acid. Hydrocarbon and simazine oxidation reaction products were analyzed by gas chromatography (GC) and high performance liquid chromatography (HPLC), respectively. This catalytic system proved to be efficient and selective for hydrocarbon oxidation, leading to high product yields from styrene (89%), cyclooctene (71%) and R-(+)-limonene (86%). Simazine oxidation was attained with 100% selectivity for a dechlorinated product (OEAT), while several oxidation products were obtained for the same catalyst in homogeneous media. The catalyst can be easily recovered through application of an external magnetic field and washed after reaction. Catalyst reuse experiments for R-(+)-limonene oxidation have shown that the catalytic activity is kept at 90% after 10 consecutive reactions.

In-situ DRIFT/MS study of the conversion of ethanol on mixed Mg/Si oxides

Due to the high price of natural oil and harmful effects of its usage, as the increase in emission of greenhouse gases, the industry focused in searching of sustainable types of the raw materials for production of chemicals. Ethanol, produced by fermentation of sugars, is one of the more interesting renewable materials for chemical manufacturing. There are numerous applications for the conversion of ethanol into commodity chemicals. In particular, the production of 1,3-butadiene whose primary source is ethanol using multifunctional catalysts is attractive. With the 25% of world rubber manufacturers utilizing 1,3-butadiene, there is an exigent need for its sustainable production. In this research, the conversion of ethanol in one-step process to 1,3-butadiene was studied. According to the literature, the mechanisms which were proposed to explain the way ethanol transforms into butadiene require to have both acid and basic sites. But still, there are a lot of debate on this topic. Thus, the aim of this research work is a better understanding of the reaction pathways with all the possible intermediates and products which lead to the formation of butadiene from ethanol. The particular interests represent the catalysts, based on different ratio Mg/Si in comparison to bare magnesia and silica oxides, in order to identify a good combination of acid/basic sites for the adsorption and conversion of ethanol. Usage of spectroscopictechniques are important to extract information that could be helpful for understanding the processes on the molecular level. The diffuse reflectance infrared spectroscopy coupled to mass spectrometry (DRIFT-MS) was used to study the surface composition of the catalysts during the adsorption of ethanol and its transformation during the temperature program. Whereas, mass spectrometry was used to monitor the desorbed products. The set of studied materials include MgO, Mg/Si=0.1, Mg/Si=2, Mg/Si=3, Mg/Si=9 and SiO2 which were also characterized by means of surface area measurements.

Aplicación de la celulosa bacteriana a la restauración del patrimonio bibliográfico y documental en papel

La preservación del patrimonio bibliográfico y documental en papel es uno de los mayores retos a los que se enfrentan bibliotecas y archivos de todo el mundo. La búsqueda de soluciones al problema del papel degradado ha sido abordada históricamente desde dos líneas de trabajo predominantes: la conservación de estos documentos mediante la neutralización de los ácidos presentes en ellos con agentes alcalinos, y su restauración mediante el método de laminación fundamentalmente con papel de origen vegetal. Sin embargo, no se ha explorado con éxito la posibilidad de reforzar la celulosa dañada, y el problema sigue sin encontrar una solución satisfactoria. Hasta el día de hoy, el desarrollo de tratamientos basados en biotecnología en la conservación del patrimonio documental ha sido muy escaso, aunque la capacidad de ciertas bacterias de producir celulosa lleva a plantear su uso en el campo de la conservación y restauración del papel. La celulosa bacteriana (CB) es químicamente idéntica a la celulosa vegetal, pero su organización macroscópica es diferente. Sus propiedades únicas (alto grado de cristalinidad, durabilidad, resistencia y biocompatibilidad) han hecho de este material un excelente recurso en diferentes campos. En el desarrollo de esta tesis se ha estudiado el uso de la celulosa bacteriana, de alta calidad, generada por Gluconacetobacter sucrofermentans CECT 7291, para restaurar documentos deteriorados y consolidar los que puedan estar en peligro de degradación, evitando así su destrucción y proporcionando al papel que se restaura unas buenas propiedades mecánicas, ópticas y estructurales. Se desarrollan asimismo protocolos de trabajo que permitan la aplicación de dicha celulosa. En primer lugar se seleccionó el medio de cultivo que proporcionó una celulosa adecuada para su uso en restauración. Para ello se evaluó el efecto que tienen sobre la celulosa generada las fuentes de carbono y nitrógeno del medio de cultivo, manteniendo como parámetros fijos la temperatura y el pH inicial del medio, y efectuando los ensayos en condiciones estáticas. Se evaluó, también, el efecto que tiene en la CB la adición de un 1% de etanol al medio de cultivo. Las capas de celulosa se recolectaron a cuatro tiempos distintos, caracterizando en cada uno de ellos el medio de cultivo (pH y consumo de fuente de carbono), y las capas de CB (pH, peso seco y propiedades ópticas y mecánicas). La mejor combinación de fuentes de carbono y nitrógeno resultó ser fructosa más extracto de levadura y extracto de maíz, con o sin etanol, que proporcionaban una buena relación entre la producción de celulosa y el consumo de fuente de carbono, y que generaban una capa de celulosa resistente y homogénea. La adición de etanol al medio de cultivo, si bien aumentaba la productividad, causaba un descenso apreciable de pH. Las capas de CB obtenidas con los medios de cultivo optimizados se caracterizaron en términos de sus índices de desgarro y estallido, propiedades ópticas, microscopía electrónica de barrido (SEM), difracción de rayos-X, espectroscopía infrarroja con transformada de Fourier (FTIR), grado de polimerización, ángulos de contacto estáticos y dinámicos, y porosimetría de intrusión de mercurio. Por otro lado hay que tener en cuenta que el material restaurado debe ser estable con el tiempo. Por ello esta misma caracterización se efectuó tras someter a las capas de CB a un proceso de envejecimiento acelerado. Los resultados mostraron que la CB resultante tiene un elevado índice de cristalinidad, baja porosidad interna, buenas propiedades mecánicas, y alta estabilidad en el tiempo. Para desarrollar los protocolos de trabajo que permitan la restauración con esta celulosa optimizada, se comienzó con un proceso de selección de los papeles que van a ser restaurados. Se eligieron tres tipos de papeles modelo, hechos con pasta mecánica, química y filtro (antes y después de ser sometidos a un proceso de envejecimiento acelerado), y tres libros viejos adquiridos en el mercado de segunda mano. Estos ejemplares a restaurar se caracterizaron también en términos de sus propiedades mecánicas y fisicoquímicas. El primer protocolo de restauración con CB que se evaluó fue el denominado laminación. Consiste en aplicar un material de refuerzo al documento mediante el uso de un adhesivo. Se seleccionó para ello la CB producida en el medio de cultivo optimizado con un 1% de etanol. Se aplicó un método de purificación alcalino (1 hora a 90 °C en NaOH al 1%) y como adhesivo se seleccionó almidón de trigo. El proceso de laminación se efectuó también con papel japonés (PJ), un material habitualmente utilizado en conservación, para comparar ambos materiales. Se concluyó que no hay diferencias significativas en las características estudiadas entre los dos tipos de materiales de refuerzo. Se caracterizó el material reforzado y, también, después de sufrir un proceso de envejecimiento acelerado. Los papeles laminados con CB mostraban diferencias más marcadas en las propiedades ópticas que los restaurados con PJ, con respecto a los originales. Sin embargo, el texto era más legible cuando el material de restauración era la CB. La mojabilidad disminuía con ambos tipos de refuerzo, aunque en los papeles laminados con CB de manera más marcada e independiente del material a restaurar. Esto se debe a la estructura cerrada de la CB, que también conduce a una disminución en la permeabilidad al aire. Este estudio sugiere que la CB mejora la calidad del papel deteriorado, sin alterar la información que contiene, y que esta mejora se mantiene a lo largo del tiempo. Por tanto, la CB puede ser utilizada como material de refuerzo para laminar, pudiendo ser más adecuada que el PJ para ciertos tipos de papeles. El otro método de restauración que se estudió fue la generación in situ de la CB sobre el papel a restaurar. Para ello se seleccionó el medio de cultivo sin etanol, ya que el descenso de pH que causaba su presencia podría dañar el documento a restaurar. El método de purificación elegido fue un tratamiento térmico (24 horas a 65 °C), menos agresivo para el material a restaurar que el tratamiento alcalino. Se seleccionó la aplicación del medio de cultivo con la bacteria mediante pincel sobre el material a restaurar. Una vez caracterizado el material restaurado, y éste mismo tras sufrir un proceso de envejecimiento acelerado, se concluyó que no hay modificación apreciable en ninguna característica, salvo en la permeabilidad al aire, que disminuye de manera muy evidente con la generación de CB, dando lugar a un material prácticamente impermeable al aire. En general se puede concluir que ha quedado demostrada la capacidad que tiene la celulosa generada por la bacteria Gluconacetobacter sucrofermentans CECT 7291 para ser utilizada como material de refuerzo en la restauración del patrimonio documental en papel. Asimismo se han desarrollado dos métodos de aplicación, uno ex situ y otro in situ, para efectuar esta tarea de restauración. ABSTRACT The preservation of bibliographic and documentary heritage is one of the biggest challenges that libraries and archives around the world have to face. The search for solutions to the problem of degraded paper has historically been focused from two predominants lines of work: the conservation of these documents by the neutralization of acids in them with alkaline agents, and their restoration by lining them with, basically, cellulose from vegetal sources. However, the possibility of strengthening the damaged cellulose has not been successfully explored, and the problem still persists. Until today, the development of biotechnology-based treatments in documentary heritage conservation has been scarce, although the ability of certain bacteria to produce cellulose takes to propose its use in the field of conservation and restoration of paper. The bacterial cellulose (BC) is chemically identical to the plant cellulose, but its macroscopic organization is different. Its unique properties (high degree of crystallinity, durability, strength and biocompatibility), makes it an excellent resource in different fields. The use of high-quality BC generated by Gluconacetobacter sucrofermentans CECT 7291 to restore damaged documents and to consolidate those that may be at risk of degradation, has been studied in this thesis, trying to prevent the document destruction, and to get reinforced papers with good mechanical, optical and structural properties. Protocols that allow the implementation of the BC as a reinforcing material were also developed. First of all, in order to select the culture medium that provides a cellulose suitable for its use in restoration, it has been evaluated the effect that the carbon and nitrogen sources from the culture medium have on the generated BC, keeping the temperature and the initial pH of the medium as fixed parameters, and performing the culture without shaking. The effect of the addition of 1% ethanol to the culture medium on BC properties was also evaluated. The cellulose layers were collected at four different times, characterizing in all of them the culture medium (pH and carbon source consumption), and the BC sheets (pH, dry weight and optical and mechanical properties). The best combination of carbon and nitrogen sources proved to be fructose plus yeast extract and corn steep liquor, with or without ethanol, which provided a good balance between the cellulose production and the consumption of carbon source, and generating BC sheets homogeneous and resistant. The addition of ethanol to the culture medium increased productivity but caused a noticeable decrement in pH. The BC layers generated with these optimized culture media, have been characterized in terms of tear and burst index, optical properties, scanning electron microscopy (SEM), X-ray diffraction, infrared Fourier transform spectroscopy (FTIR), polymerization degree, static and dynamic contact angles, and mercury intrusion porosimetry. Moreover it must be kept in mind that the restored materials should be stable over time. Therefore, the same characterization was performed after subjecting the layers of BC to an accelerated aging process. The results showed that the BC sheets obtained have a high crystallinity index, low internal porosity, good mechanical properties, and high stability over time. To develop working protocols to use this optimized BC in paper restoration, the first step was to select the samples to restore. Three types of model papers, made from mechanical pulp, chemical pulp and filter paper (before and after an accelerated aging process), and three old books purchased in the second hand market, were chosen. These specimens to be restored were also characterized in terms of its mechanical and physicochemical properties. The first protocol of restoration with BC to be evaluated is called linning. It consists on applying a reinforcing material to the document using an adhesive. The BC produced in the optimized culture medium with 1% ethanol was selected. An alkali purification method (1 hour at 90 °C in 1% NaOH) was applied, and wheat starch was selected as adhesive. The linning process was also carried out with Japanese paper (JP), a material commonly used in conservation, in order to compare both materials. It was concluded that there are no significant differences in the characteristics studied of the two types of reinforcing materials. The reinforced materials were characterized before and after undergoing to an accelerated aging. Papers lined with BC showed more marked differences in the optical properties that papers restored with JP. However, the text was more readable when BC was the reinforcing material. Wettability decreased with both types of reinforcement, although in the papers linned with BC it happened more marked and independently of the sample to restore. This is due to the closed structure of BC, which also leads to a decrement in air permeance. This study suggests that BC improves the deteriorated paper quality, without altering the information on it, and that this improvement is maintained over time. Therefore, the BC may be used as reinforcing material for linning, being more suitable than the JP to restore certain types of papers. The other restoration method to be evaluated was the in situ generation of BC over the paper to restore. For this purpose the culture medium without ethanol was selected, as the pH decrement caused by his presence would damage the document to restore. As purification method a heat treatment (24 hours at 65 °C) was chosen, less aggressive to the material to restore than the alkaline treatment. It was decided to apply the culture medium with the bacteria onto the material to restore with a brush. The reinforced material was characterized before and after an accelerated aging process. It was concluded that there was no substantial change in any characteristic, except for air permeance, which decreases very sharply after the generation of BC, getting a substantially air impermeable material. In general, it can be concluded that the ability of BC produced by Gluconacetobacter sucrofermentans CECT 7291 for its use as a reinforcing material in the restoration of paper documentary heritage, has been demonstrated. Also, two restoration methods, one ex situ and another in situ have been developed.

Estudo de nanocompósitos formados por PLA e nanopartículas de celulose.

Devido à preocupação com o meio ambiente e o volume crescente de resíduos plástico em aterros sanitários, os polímeros biodegradáveis estão sendo estudados extensivamente. Um deles é o PLA. Apesar de possuir propriedades comparáveis a polímeros commodities e polímeros de engenharia, ainda é necessário melhorar certas características do PLA, como resistência ao impacto. Para isso, a nanocelulose (NC) pode ser usada sem alterações significativas na biodegradação polimérica. Este estudo teve como objetivo obter a nanocelulose, caracteriza-la e incorpora-la ao poli(ácido láctico) (PLA), assim como, estudar as propriedades térmicas, morfológicas e mecânicas do compósito obtido. A NC foi obtida por hidrólise ácida utilizando ácido fosfórico e posteriormente foi silanizada com três silanos distintos. As nanopartículas foram caracterizadas por Birrefringência, Microscopia Eletrônica de Transmissão (MET), Termogravimetria (TG), Potencial Zeta, Espectroscopia Vibracional de Absorção no Infravermelho com Transformada de Fourier (FTIR) e Difração de Raio X (DRX). Com as imagens obtidas pelo MET foi possível medir o tamanho das partículas de NC. E então obter a razão de aspecto de 82 e o limite de percolação de 1,1% em massa, confirmando a morfologia de nanofibra. De acordo as analises TG\'s, a presença de NC silanizada aumentou o início da degradação térmica. Os compósitos, contendo 3% em massa de NC, foram obtidos por fusão em câmara de mistura e moldados por injeção. Os compósitos foram caracterizados por FTIR, Cromatografia de Permeação em Gel (GPC), TG, Calorimetria Exploratória Diferencial (DSC), Microscopia Eletrônica de Varredura (MEV-FEG), Impacto e Tração. As análises dos compósitos mostraram que a NC atuou como agente de nucleação, facilitando a cristalização do PLA, além de a NC ter atuado como reforço na matriz polimérica melhorando as propriedades mecânicas.

Síntese e caracterização de complexos de Co(II) e Ni(II) com l-dopa, carbidopa e benzimidazol

Were synthesized in this work in the following aqueous solution coordination compounds: [Ni(LDP)(H2O)2Cl2].2H2O, [Co(LDP)Cl2].3H2O, [Ni(CDP)Cl2].4H2O, [Co(CDP)Cl2].4H2O, [Ni(BDZ)2Cl2].4H2O and [Co(BDZ)2Cl2(H2O)2]. These complexes were synthesized by stoichiometric addition of the binder in the respective metal chloride solutions. Precipitation occurred after drying the solvent at room temperature. The characterization and proposed structures were made using conventional analysis methods such as elemental analysis (CHN), absorption spectroscopy in the infrared Fourier transform spectroscopy (FTIR), X-ray diffraction by the powder method and Technical thermoanalytical TG / DTG (thermogravimetry / derivative thermogravimetry) and DSC (differential scanning calorimetry). These techniques provided information on dehydration, coordination modes, thermal performance, composition and structure of the synthesized compounds. The results of the TG curve, it was possible to establish the general formula of each compound synthesized. The analysis of X-ray diffraction was observed that four of the synthesized complex crystal structure which does not exhibit the complex was obtained from Ldopa and carbidopa and the complex obtained from benzimidazole was obtained crystal structures. The observations of the spectra in the infrared region suggested a monodentate ligand coordination to metal centers through its amine group for all complexes. The TG-DTG and DSC curves provide important information and on the behavior and thermal decomposition of the synthesized compounds. The molar conductivity data indicated that the solutions of the complexes formed behave as a nonelectrolyte, which implies that chlorine is coordinated to the central atom in the complex.