Síntese e caracterização de PSFC (Pr0,5Sr0,5Fe1-xCuxO3-δ, sendo x=0,2 e x=0,4) para aplicação como catodo de células a combustível de óxido sólido

The PSFC (Pr0.5Sr0.5Fe1-xCuxO3-δ) is a new mixed oxide perovskite and has been studied and evaluated the cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFCs), mainly due to its good compatibility with the electrolyte (CGO) and its high ionic conductivity and electronic in intermediate temperature. In this work, PSFC powders with two different compositions (Pr0,5Sr0,5Fe0,8Cu0,2O3- PSFC5582 and Pr0,5Sr0,5Fe0,6Cu0,4O3-PSFC5564) were synthesized by the citrate method using a new route. The powders obtained were characterized by thermal analysis (Differential Scanning Calorimetry and Thermogravimetry), and the material calcined at 800, 900 and 1000 °C for 5h were analyzed by X-ray diffractometry (XRD), with the Rietveld refinement of the diffraction data and dilatometry. PSFC5582 composite films were obtained by screen printing of powder calcined at 1000 °C. The films were deposited on substrate ceria doped with gadolinia (CGO) and then sintered at 1050 °C for 2h. The electrochemical performance of the electrodes was evaluated by impedance spectroscopy and the interface electrode/electrolyte was observed by scanning electron microscopy (SEM). The specific resistance area (ASR) was 0.44 Ω.cm² at 800 °C, slightly lower than those reported in the literature for cathodes containing cobalt. The thermal expansion coefficients of both the PSFC compositions were obtained and varied between 13 and 15 x 10-6 °C-1 , in a temperature range of 200 to 650 °C, demonstrating the good thermal compatibility of cathodes with Ce0,9Gd0,1O1,95 electrolytes (CET = 12 x 10-6 °C).

An effective three-dimensional ordered mesoporous CuCo2O4 as electrocatalyst for Li-O2 batteries

Three-dimensional ordered mesoporous (3DOM) CuCo₂O₄ materials have been synthesized via a hard template and used as bifunctional electrocatalysts for rechargeable Li-O₂ batteries. The characterization of the catalyst by X-ray diffractometry and transmission electron microscopy confirms the formation of a single-phase, 3-dimensional, ordered mesoporous CuCo₂O₄ structure. The as-prepared CuCo₂O₄ nanoparticles possess a high specific surface area of 97.1 m² g^{- 1} and a spinel crystalline structure. Cyclic voltammetry demonstrates that mesoporous CuCo₂O₄ catalyst enhances the kinetics for either oxygen reduction reaction (ORR) or oxygen evolution reaction (OER). The Li-O₂ battery utilizing 3DOM CuCo₂O₄ shows a higher specific capacity of 7456 mAh g^{- 1} than that with pure Ketjen black (KB). Moreover, the CuCo₂O₄-based electrode enables much enhanced cyclability with a 610 mV smaller discharge-recharge voltage gap than that of the carbon-only cathode at a current rate of 100 mA g^{- 1}. Such excellent catalytic performance of CuCo₂O₄ could be associated with its larger surface area and 3D ordered mesoporous structure. The excellent electrochemical performances coupled with its facile and cost-effective way will render the 3D mesoporous CuCo₂O₄ nanostructures as attractive electrode materials for promising application in Li-O₂ batteries.

Cold vapour generation electrothermal atomic absorption spectrometry and solid phase extraction based on a new nanosorbent for sensitive HG determination in environmental samples (sea water and river water)

Mercury is not an essential element for plant or animal life and it is a potential environmental toxic because of its tendency to form covalent bonds with organic molecules and the high stability of the Hg-C bond. Reports estimate a total mercury concentration in natural waters ranging from 0.2 to 100 ng L-1. Due to this fact, highly sensitive methods are required for direct determination of such extremely low levels. In this work, a rapid and simple method was developed for separation and preconcentration of mercury by flow injection solid phase extraction coupled with on-line chemical vapour generation electrothermal atomic absorption spectrometry. The system is based on chelating retention of the analyte onto the mini column filled with a mesoporous silica functionalized with 1,5 bis (di-2-pyridyl) methylene thiocarbohydrazide. The main aim of this work was to develop a precise and accurate method for the determination of the Hg. Under the optima conditions and 120 s preconcentration time, the detection limit obtained was 0.009 μg L-1, with RSDs 3.7 % for 0.2 μg L-1, 4.8 % for 1 μg L-1 and enrichment factor 4, Furthermore, the method proposed has permitted the determination of Hg with a reduction in the analysis time, the sample throughput was about 18 h-1, low consumption of reagents and sample volume. The method was applied to the determination of Hg in sea water and river water. For the quality control of the analytical performance and the validation of the newly developed method, the analysis of two certified samples, TMDA 54.4 Fortified Lake, and LGC6187 River sediment was addressed. The results showed good agreement with the certified values.

Synthesis and antibacterial study of some s-substituted aliphatic analogues of 2-mercapto-5-(1-(4-toluenesulfonyl) piperidin-4-yl)-1,3,4-oxadiazole

Purpose: To synthesize a series of analogues of 1,3,4-oxadiazole and to evaluate their antibacterial activity. Methods: Ethyl piperidin-4-carboxylate (1) was mixed with 4-toluenesulfonyl chloride (2) in benignant conditions to yield ethyl 1-(4-toluenesulfonyl)piperidin-4-carboxylate (3) and then 1-(4- toluenesulfonyl)piperidin-4-carbohydrazide (4). Intermolecular cyclization of 4 into 2-mercapto-5-(1-(4- toluenesulfonyl) piperidin-4-yl)-1,3,4-oxadiazole (5) was obtained on reflux with CS2 in the presence of KOH. Molecule 5 was stirred with alkyl halides, 6a-i, in DMF in the presence of LiH to synthesize the final compounds, 7a-i. The structures of these molecules were elucidated by Fourier transform infra-red (FTIR) spectroscopy, proton nuclear magnetic resonance (1H-NMR) and electron impact mass spectrometry (EI-MS). Antibacterial activity was evaluated against five bacterial strains, namely, Salmonella typhi, Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Bacillus subtilis, with ciprofloxacin used as standard antibacterial agent. Results: Out of nine synthesized derivatives, compound 7a was the most active against three bacterial strains, S. typhi, E. coli and P. aeruginosa, with minimum inhibitory concentration (MIC) of 9.11 ± 0.40, 9.89 ± 0.45 and 9.14 ± 0.72 μM, respectively, compared with 7.45 ± 0.58, 7.16 ± 0.58 and 7.14 ± 0.18 μM, respectively, for the reference standard (ciprofloxacin). Similarly, compounds 7a - 7c showed relatively good antibacterial activity against B. subtilis strain while compound 7e - 7g revealed good results against S. typhi bacterial strain. Conclusion: The results indicate that S-substituted derivatives of the parent compound are more effective antibacterial agents than the parent compound, even with minor differences in substituents

Modellazione e simulazione di un processo di produzione per l'industria 4.0

In un mondo in continua trasformazione cresce sempre più il numero delle aziende che hanno colto l’importanza della digitalizzazione dei processi produttivi. Alcune di esse si affidano ad esperti capaci di suggerire soluzioni per ottenere servizi di alta qualità e fruibilità con l’integrazione di sistemi gestionali. Il presente lavoro di tesi ha come obiettivo l’analisi del processo produttivo di una azienda che realizza armadi per stazioni di ricarica elettrica serie terra a colonna. Si compone di sei capitoli, il primo affronta il tema della Simulazione e le sue principali caratteristiche per analizzare un processo di produzione; il secondo esamina i linguaggi, le applicazioni e i modelli di simulazione; il terzo analizza e descrive le peculiarità e le caratteristiche del software utilizzato per la simulazione; il quarto capitolo affronta il tema dell’industria 4.0 spingendo all’innovazione nei sistemi produttivi per raggiungere una produzione del tutto automatizzata e interconnessa; nel quinto viene descritto il modello digitale per ottenere in modo preciso un oggetto fisico, così da avere una Simulazione precisa, infine, il sesto esamina la Simulazione e Modellizzazione come strumento per l’ottimizzazione del processo produttivo riguardante armadi per stazioni di ricarica elettrica serie terra a colonna. Il raggiungimento dell’uso della simulazione come supporto all’analisi dinamica di un processo consente di avere una panoramica complessiva di tutte le operazioni, rappresentando, così un vantaggio per le aziende che possono valutare con oggettività soluzioni progettuali alternative, di cui è difficile prevedere il comportamento, le prestazioni e l’impatto su altri sistemi. Questi risultati sono la risposta alle necessità di disporre strumenti per l’anticipazione, il dimensionamento e il contenimento dei rischi di progetto.

Spin labile conducting metallopolymers : a new architecture for hybrid multifunctional materials

The synthesis of 3-ethynylthienyl- (2.07), 3-ethynylterthienyl- (2.19) substituted qsal [qsalH = N-(8-quinolyl)salicylaldimine] and 3,3' -diethynyl-2,2' -bithienyl bridging bisqsal (5.06) ligands are described along with the preparation and characterization of eight cationic iron(III) complexes containing these ligands with a selection of counteranions [(2.07) with: SCN- (2.08), PF6- (2.09), and CI04- (2.10); (2.19) with PF6 - (2.20); (5.06) with: cr (5.07), SeN- (5.08), PF6- (5.09), and CI04- (5.10)]. Spin-crossover is observed in the solid state for (2.08) - (2.10) and (5.07) - (5.10), including a ve ry rare S = 5/2 to 3/2 spin-crossover in complex (2.09). The unusal reduction of complex (2.10) produces a high-spin iron(I1) complex (2.12). Six iron(II) complexes that are derived from thienyl analogues of bispicen [bispicen = bis(2-pyridylmethyl)-diamine] [2,5-thienyl substituents = H- (3.11), Phenyl- (3.12), 2- thienyl (3.13) or N-phenyl-2-pyridinalimine ligands [2,5-phenyl substituents = diphenyl (3.23), di(2-thienyl) (3.24), 4-phenyl substituent = 3-thienyl (3.25)] are reported Complexes (3.11), (3.23) and (3.25) display thermal spin-crossover in the solid state and (3.12) remains high-spin at all temperatures. Complex (3.13) rearranges to form an iron(II) complex (3.14) with temperature dependent magnetic properties be s t described as a one-dimensional ferromagnetic chain, with interchain antiferromagnetic interactions and/or ZFS dominant at low temperatures. Magnetic succeptibility and Mossbauer data for complex (3.24) display a temperature dependent mixture of spin isomers. The preparation and characterization of two cobalt(II) complexes containing 3- ethynylthienyl- (4.04) and 3-ethynylterhienyl- (4.06) substituted bipyridine ligands [(4.05): [Co(dbsqh(4.04)]; (4.07): [Co(dbsq)2(4.06)]] [dbsq = 3,5-dbsq=3,5-di-tert-butylI ,2-semiquinonate] are reported. Complexes (4.05) and (4.07) exhibit thermal valence tautomerism in the solid state and in solution. Self assembly of complex (2.10) into polymeric spheres (6.11) afforded the first spincrossover, polydisperse, micro- to nanoscale material of its kind. . Complexes (2.20), (3.24) and (4.07) also form polymers through electrochemical synthesis to produce hybrid metaUopolymer films (6.12), (6.15) and (6.16), respectively. The films have been characterized by EDX, FT-IR and UV-Vis spectroscopy. Variable-temperature magnetic susceptibility measurements demonstrate that spin lability is operative in the polymers and conductivity measurements confirm the electron transport properties. Polymer (6.15) has a persistent oxidized state that shows a significant decrease in electrical resistance.

Thymine hydroperoxide as a potential source of singlet molecular oxygen in DNA

The decomposition of organic hydroperoxides into peroxyl radicals is a potential source of singlet molecular oxygen [O(2) ((1)Delta(g))] in biological systems. This study shows that 5-(hydroperoxymethyl)uracil (5-HPMU), a thymine hydroperoxide within DNA, reacts with metal ions or HOCl, generating O(2) ((1)Delta(g)). Spectroscopic evidence for generation of O(2) ((1)Delta(g)) was obtained by measuring (i) the bimolecular decay, (ii) the monomolecular decay, and (iii) the observation of D(2)O enhancement of O(2) ((1)Delta(g)) production and the quenching effect of NaN(3). Moreover, the presence of O(2) ((1)Delta(g)) was unequivocally demonstrated by the direct characterization of the near-infrared light emission. For the sake of comparison, O(2) ((1)Delta(g)) derived from the H(2)O(2)/HOCl system and from the thermolysis of the N,N`-di(2,3-dihydroxypropyl)-1,4-naphthalenedipropanamide endoperoxide was also monitored. More evidence of O(2) ((1)Delta(g)) generation was obtained by chemical trapping of O(2) ((1)Delta(g)) with anthracene-9,10-divinylsulfonate (AVS) and detection of the specific AVS endoperoxide by HPLC/MS/MS. The detection by HPLC/MS of 5-(hydroxymethyl)uracil and 5-formyluracil, two thymine oxidation products generated from the reaction of 5-HPMU and Ce(4+) ions, supports the Russell mechanism. These photoemission properties and chemical trapping clearly demonstrate that the decomposition of 5-HPMU generates O(2) ((1)Delta(g)) by the Russell mechanism and point to the involvement of O(2) ((1)Delta(g)) in thymidine hydroperoxide cytotoxicity. (C) 2009 Elsevier Inc. All rights reserved.

Iron-Promoted Nucleophilic Additions to Diimine-Type Ligands: A Synthetic and Structural Study

We report here three examples of the reactivity of protic nucleophiles with diimine-type ligands in the presence of FeII salts. In the first case, the iron-promoted alcoholysis reaction of one nitrile group of the ligand 2,3-dicyano-5,6-bis(2-pyridyl)-pyrazine (L1) permitted the isolation of an stable E-imido−ester, [Fe(L1‘)2](CF3SO3)2 (1), which has been characterized by spectroscopic studies (IR, ES-MS, Mössbauer), elemental analysis, and crystallographically. Compound 1 consists of mononuclear octahedrally coordinated FeII complexes where the FeII ion is in its low-spin state. The iron-mediated nucleophilic attack of water to the asymmetric ligand 2,3-bis(2-pyridyl)pyrido[3,4-b]pyrazine (L2) has also been studied. In this context, the crystal structures of two hydration−oxidation FeIII products, [Fe(L2‘)2](ClO4)3·3CH3CN (2) and trans-[FeL2‘‘Cl2] (3), are described. Compounds 2 and 3 are both mononuclear FeIII complexes where the metals occupy octahedral positions. In principle, L2 is expected to coordinate to metal ions through its bipyridine-type units to form a five-membered ring; however, this is not the case in compounds 2 and 3. In 2, the ligand coordinates through its pyridines and through the hydroxyl group attached to the pyrazine imino carbon after hydration, that is, in an N,O,N tridentate manner. In compound 3, the ligand has suffered further transformations leading to a very stable diamido complex. In this case, the metal ion achieves its octahedral geometry by means of two pyridines, two amido N atoms, and two axial chlorine atoms. Magnetic susceptibility measurements confirmed the spin state of these two FeIII species:  compounds 2 and 3 are low-spin and high-spin, respectively.

Ultrafast excited state dynamics controlling photochemical isomerization of N-methyl-4-[trans-2-(4-pyridyl)ethenyl]pyridinium coordinated to a {Re-1(CO)(3)(2,2 '-bipyridine)} chromophore

Two Multifunctional photoactive complexes [Re(Cl)(CO)(3)-(MeDpe(+))(2)](2+) and [Re(MeDpe(+))(CO)(3)(bpy)](2+) (MeDpe(+) = N-methyl-4-[trans-2-(4-pyridyl)ethenyl]pyridinium, bpy = 2,2'-bipyridine) were synthesized. characterized. and their redox and photonic properties were investigated by cyclic voltammetry: ultraviolet-visible-infrared (UV/Vis/IR) spectroelectrochemistry, stationary UV/Vis and resonance Raman spectroscopy; photolysis; picosecond time-resolved absorption spectroscopy in the visible and infrared regions: and time-resolved resonance Raman spectroscopy. The first reduction step of either complex Occurs at about -1.1 V versus Fc/Fc(+) and is localized at MeDpe(+). Reduction alone does not induce a trans -> cis isomerization of MeDpe(+). [Re(Cl)(CO)(3)(MeDPe(+))(2)](2+) is photostable, while [Re(MeDpe(+))(CO)(3)(bpy)](2+) and free MeDpe(+) isomerize under near-UV irradiation. The lowest excited state of [Re(Cl)(CO)(3)(MeDPe(+))(2)](2+) has been identified as the Re(Cl)(CO)(3) -> MeDpe(+) (MLCT)-M-3 (MLCT = metal-to-ligand charge transfer), decaying directly to the ground state with lifetimes of approximate to 42 (73%) and approximate to 430ps (27%). Optical excitation of [Re(MeDpe(+))(CO)(3)(bpy)](2+) leads to population of Re(CO)(3) -> MeDpe(+) and Re(CO)(3) -> bpy (MLCT)-M-3 states, from which a MeDpe(+) localized intraligand 3 pi pi* excited state ((IL)-I-3) is populated with lifetimes of approximate to 0.6 and approximate to 10 ps, respectively. The 3IL state undergoes a approximate to 21 ps internal rotation, which eventually produces the cis isomer on a much longer timescale. The different excited-state behavior of the two complexes and the absence of thermodynamically favorable interligand electron transfer in excited [Re(MeDpe(+))(CO)(3)(bpy)](2+) reflect the fine energetic balance between excited states of different orbital origin, which can be tuned by subtle Structural variations. The complex [Re(MeDpe+)(CO)(3)(bpy)](2+) emerges as a prototypical, multifunctional species with complementary redox and photonic behavior.

Binuclear cyclopalladated compounds with antitubercular activity: synthesis and characterization of [{Pd(C-2,N-dmba)(X)}(2)(mu-bpp)] (X = Cl, Br, NCO, N-3; bpp=1,3-bis(4-pyridyl)propane)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A Facile synthesis of 3-Methylene-4-aryl-1,3,4,5-tetrahydro-benzo[b][1,4] di-azepin-2-ones and 3-arylemethylene-4,5-dihydro-3H-benzo[b][1,4]diazepin-2-ylamines

A simple and convenient synthesis of 3-methylene-4-aryl-1,3,4,5-tetrahydro-benzo[b][1,4] diazepin-2-ones was accomplished by the SN2 nucleophilic substitution of the acetates of Baylis-Hillman adducts of acrylate with 1,2-phenylenediamines followed by base-mediated intramolecular cyclization. On the other hand similar substrates derived from the Baylis-Hillman adducts of acrylonitrile via Pinner’s reaction leads to 3-arylmethylene-4,5-dihydro-3H-benzo[b][1,4]diazepin-2-ylamines in good yields..

Quinolizine-2,4-diones by reversible dimerisation 2-pyridylketenes

Quinolizine-2,4-diones 11 are obtained by ash vacuum thermolysis (FVT) of 3-acyl-1,2,3-triazolo[1,5-a]pyridines 7. The reaction takes place via methyl- and phenyl(2-pyridyl)ketenes 10, which are directly observable by infrared spectroscopy in low temperature matrices. FVT of 11 regenerates the ketenes 10.

Synthesis and Coordination Chemistry of a New N-4-Polydentate Class of Pyridyl-Functionalized Scorpionate Ligands: Complexes of Fe-II, Zn-II, V-IV, Pd-II and Use for Heterobimetallic Systems

The new potentially N-4-multidentate pyridyl-functionalized scorpionates 4-((tris-2,2,2-(pyrazol-1-ypethoxy)methyl)pyridine (TpmPy, (1)) and 4-((tris-2,2,2-(3-phenylpyrazol-1-yl)ethoxy)methyl)pyridine (TpmPy(Ph), (2)) have been synthesized and their coordination behavior toward Fe-II, Ni-II, Zn-II, Cu-II, Pd-II, and V-III centers has been studied. Reaction of (1) with Fe(BF4)(2)center dot 6H(2)O yields [Fe(TpmPy)(2)](BF4)(2) (3), that, in the solid state, shows the sandwich structure with trihapto ligand coordination via the pyrazolyl arms, and is completely low spin (LS) until 400 K. Reactions of 2 equiv of (1) or (2) with Zn-II or Ni-II chlorides give the corresponding metal complexes with general formula [MCl2(TpmPy*)(2)] (M = Zn, Ni; TpmPy* = TpmPy, TpmPy(Ph)) (4-7) where the ligand is able to coordinate through either the pyrazolyl rings (in case of [Ni(TpmPy)(2)Cl-2 (5)) or the pyridyl-side (for [ZnCl2(TpmPy)(2)] (4), [ZnCl2(TpmPy(Ph))(2)] (6) and [NiCl2(TpmPy(Ph))(2)] (7)). The reaction of (1) with VCl3 gives [VOCl2(TpmPy)] (8) that shows the N-3-pyrazolyl coordination-mode. Moreover, (1) and react with cis-[PdCl2(CH3CN)(2)] to give the disubstituted complexes [PdCl2(TprnPy)(2)] (9) and [PdCl2(TpmPy(Ph))(2)] (10), respectively, bearing the scorpionate coordinated via the pyridyl group. Compounds (9) and (10) react with Fe(BF4)(2) to give the heterobimetallic Pd/Fe systems [PdCl2(mu-TpmPy)(2)-Fe](BF4)(2) (11) and [PdCl2(mu-TpmPy(Ph))(2)Fe-2(H2O)(6)]BF4)(4) (13), respectively. Compound (11) can also be formed from reaction of (3) with cis-[PdCl2(CH3CN)(2)], while reaction of (3) with Cu(NO3)(2).2.5H(2)O generates [Fe(mu-TpmPy)(2)-Cu(NO3)(2)](BF4)(2) (12), confirming the multidentate ability of the new chelating ligands. The X-ray diffraction analyses of compounds (1), (3), (4), (5), and (9) are also reported.

Diazafluoren-9-yliden als Bindungsmotiv für Metallfragmente in kreuzkonjugierten π-Systemen

In der vorliegenden Dissertation wurden kreuzkonjugierte organische Verbindungen basierend auf Diazafluorenmethyliden- sowie Dipyridylmethyliden-Bausteinen synthetisiert, die zum einen photoredoxaktive Metallfragmente komplexieren können und zum anderen erweiterte π-konjugierte Pfade auf der Grundlage von Alkineinheiten ermöglichen. Das kreuzkonjugierte Motiv wurde über die Kupplung von Alkineinheiten an halogenierte Methyliden-Einheiten, den so genannten Dibromolefinen, zugänglich gemacht. Zur Synthese von Dibromolefinen wurden verschiedene Methoden untersucht. Literaturbekannte Methoden wie die Wittig-Reaktion und ihre Modifikationen sowie die Corey-Fuchs-Reaktion konnten für die Diazafluoreneinheit nicht erfolgreich angewendet werden. Bei einer mikrowellenunterstützten Reaktion konnte sowohl ausgehend von Diazafluoren-9-on als auch von Di-2-pyridylketon eine Dibromolefinierung (55 % und 65 %) erreicht werden. Die Eignung der Mikrowellenstrahlung für Dibromolefinierungsreaktionen nach Corey und Fuchs wurde weiterhin an verschiedenen Aldehyden und Ketonen untersucht. In den meisten Fällen konnten gute bis sehr gute Ergebnisse erzielt werden. Durch die erfolgreiche Synthese von Dibromolefinen über Mikrowellensynthese wurde die Realisierung von diversen π-konjugierten Systemen möglich. Dies erfolgte exemplarisch durch die Kupplung der Alkine 5-Ethinyl-2,2’-bipyridin, 1-(Ferrocenylethinyl)-4-(ethinyl)benzol, Tri(tolyl)propin sowie der TIPS- und TMS-Acetylene. Neben der Vielfalt an Möglichkeiten zur Funktionalisierung von Dipyridyl- und Diazafluorenbausteinen zeigte sich zudem, dass sogar räumlich anspruchsvolle Verbindungen wie die geminale angeordneten voluminösen Tri(tolyl)propinyl-Substituenten an der Doppelbindung erfolgreich synthetisiert werden können. Die Koordinationseigenschaften der neu synthetisierten Verbindungen konnten durch Umsetzungen der Diazafluoren- und Dipyridylverbindungen mit PdCl2 und [RuCl2(bpy)2] erfolgreich gezeigt werden. Im Hinblick auf die Herstellung von Funktionsmaterialien eignen sich die Endiin-Strukturmotive aufgrund von diversen Variationsmöglichkeiten wie Koordination von Übergangsmetallen sowie Funktionalisierung der Peripherie gut. Dadurch können die elektronischen Eigenschaften wie die Absorption oder elektrochemische Potentiale der Verbindungen modifiziert werden. Die UV/Vis-Spektren der neu synthetisierten Verbindungen zeigen, dass Absorptionen in längerwelligen Bereichen durch Verlängerung des Konjugationspfades gesteuert werden können. Zudem lassen sich weitere photophysikalische Eigenschaften wie MC-, LC-, LMCT- oder MLCT-Übergänge durch Koordination von Metallen generieren. Die elektrochemischen Potentiale der Dipyridyl- und Diazafluorenbausteine konnten durch Anbindung von verschiedenen Substituenten beeinflusst werden. Es zeigte sich, dass sich die Reduktionswellen im Vergleich zu denen der Ketone zu niedrigeren Potentialen verschieben, wenn Alkine an die Dipyridylmethyliden- und Diazafluorenmethyliden-Bausteine geknüpft wurden. Zudem konnte beobachtet werden, dass die Signale nicht immer reversibel sind. Insbesondere die Dipyridylverbindungen zeichneten sich durch irreversible Reduktionswellen aus. Die Realisierung von π-konjugierten Systemen gelang auch mit cyclischen kohlenstoffbasierten Verbindungen. Über das separat synthetisierte 2,2’-Diethinyltolan konnte eine cyclische Verbindung, ein dehydroannulen-radialenisches System, erfolgreich hergestellt werden. Die Koordination von redoxaktiven Metallzentren wie [Ru(bpy)2] konnte für diese Verbindung ebenfalls erfolgreich gezeigt werden. Die elektronische Wechselwirkung zwischen dem Metallzentrum und dem dehydroannulenischen System könnte sowohl über theoretische Methoden (zeitabhängige Dichtefunktionaltheorie) als auch experimentell wie z. B. über transiente Absorptionsspektroskopie untersucht werden. Diese zukünftig durchzuführenden Untersuchungen können Aufschluss über die Ladungstransferraten und -dauer geben. Im Hinblick auf die Realisierung von Modellverbindungen für molekulare Drähte wurden lineare Systeme basierend auf der Diazafluoreneinheit synthetisiert. Zur Synthese von derartigen Systemen war es zunächst notwendig, die Dibromolefine unsymmetrisch zu alkinylieren. Die unsymmetrische Substitution gestaltete sich als Herausforderung, da eine Einfachkupplung mit einem Acetylen nicht möglich war. In den meisten Fällen wurden zweifach substituierte Spezies mit den identischen Alkinen erhalten. Die besten Ausbeuten konnten durch die konsekutive Zugabe von TIPS-Acetylen und darauffolgend TMS-Acetylen in die Reaktionsmischung erhalten werden. Offenbar spielt der räumliche Anspruch des Erstsubstituenten in diesem Zusammenhang eine Rolle. Die selektive Entschützung der unterschiedlich silylierten Verbindungen erfolgte mit K2CO3 in MeOH/THF (1:1). Die oxidative Homokupplungsreaktion erfolgte ohne Isolierung der entschützten Spezies, da diese instabil ist und zur Polymerisation neigt. Aufgrund der Instabilität der entschützten Spezies sowie möglichen Nebenreaktionen waren die Ausbeuten sowohl bei der TIPS-geschützten Verbindung als auch bei der TTP-geschützten Verbindung gering. Versuche, lineare Systeme von dipyridylbasierten Verbindungen zu erhalten, schlugen fehl. Die π-konjugierten Systeme lassen aufgrund der effektiven Überlappung der beteiligten π-Orbitale hohe Ladungsträgermobilitäten vermuten. Die im Rahmen dieser Arbeit synthetisierten Verbindungen könnten mit Schwefelverbindungen die Anbindung an Elektroden zulassen, worüber die Leitfähigkeiten der Verbindungen gemessen werden könnten.

Spectroscopic Investigation on the Formation of a Dinuclear Me(2)SO-Ru(2)-Mercaptopyridine Bridged Complex: [Ru(2)Cl(3)(mu-pyS)(mu-dmso)(dmso)(4)]center dot 2H(2)O

A dinuclear ruthenium(II) complex double-bridged by an N-aromatic ligand 2-mercaptopyridine (2-pyridinethiol or 2-pyridyl mercaptan) and a methyl sulfoxide (dmso) have been characterized by X-ray crystallography. The reported compound with formula [Ru(2)Cl(3) (mu-pyS)(mu-dmso)(dmso)(4)] center dot 2H(2)O, [C(15)H(36)Cl(3)NO(7)S(6)Ru(2)] (P2/c, a = 13.8175(2) angstrom, b = 10.5608(2) angstrom, c = 21.3544 (3) angstrom, beta = 106.090(1)degrees, V = 2,994.05(8) angstrom(3), Z = 4) represents a seven-membered ring system with both rutheniums in an octahedral geometry. All the hydrogen bonds (C-H-Cl) and the van der Waals contacts give rise to three-dimensional network in the structure and add stability to the dinuclear compound. To our knowledge, this is the first time that the formation of a dinuclear ruthenium(II) complex double-bridged by an N-aromatic ligand 2-mercaptopyridine and dmso have been reported. The study also provided valuable insight into bioinorganic chemistry as continuing efforts are being made to develop metal-based cancer chemotherapeutics. A major feature of this paper is the resolution of a double bridged ruthenium structure which contributes to a better understanding of ruthenium reactivity.