Effect Of Directionality Of Grinding Marks On Friction And Formation Of Transfer Layer

Surface texture influences friction and transfer layer formation during sliding. In the present investigation, basic studies were conducted using inclined pin-on-plate sliding tester to understand the effect of directionality of surface grinding marks of hard material on friction and transfer layer formation during sliding against soft materials. 080 M40 steel plates were ground to attain different surface roughness with unidirectional grinding marks. Then pins made of soft materials such as pure Al, pure Mg and Al-Mg alloy were slid against the prepared steel plates. Grinding angle (i.e., the angle between direction of sliding and grinding marks) was varied between 0 degrees and 90 degrees in the tests. Experiments were conducted under both dry and lubricated conditions on each plate in ambient environment. It was observed that the transfer layer formation and the coefficient of friction, which has two components adhesion and plowing - depend primarily on the directionality of grinding marks of the harder mating surface, and independent of surface roughness of the harder mating surface. For the case of pure Mg, stick-slip phenomenon was observed under dry condition for all grinding angles and it was absent upto 20 degrees grinding angles under lubricated condition. However, for the case of Al, it was observed only under lubricated conditions for angles exceeding 20 degrees. As regards the alloy, namely, Al-Mg alloy, it, was absent in both conditions. For the case of pure Mg and Al, it was observed that the amplitude of stick-slip motion primarily depends on plowing component of friction. The grinding angle effect on coefficient of friction was attributed to the variation of plowing component of friction with grinding angle.

Studies On Friction And Formation Of Transfer Layer In Hcp Metals

Surface texture plays an important role in the frictional behavior and transfer layer formation of contacting surfaces. In the present investigation, basic experiments were conducted using an inclined pin-on-plate sliding apparatus to better understand the role of surface texture on the coefficient of friction and the formation of a transfer layer. In the experiments, soft HCP materials such as pure Mg and pure Zn were used for the pins and a hardened 080 M40 steel was used for the plate. Two surface parameters of the steel plates—roughness and texture—were varied in tests that were conducted at a sliding speed of 2 mm/s in ambient conditions under both dry and lubricated conditions. The morphologies of the worn surfaces of the pins and the formation of the transfer layer on the counter surfaces were observed using a scanning electron microscope. In the experiments, the occurrence of stick-slip motion, the formation of a transfer layer, and the value of friction were recorded. With respect to the friction, both adhesion and plowing components were analyzed. Based on the experimental results, the effect of surface texture on the friction was attributed to differences in the amount of plowing. Both the plowing component of friction and the amplitude of stick-slip motion were determined to increase surface textures that promote plane strain conditions and decrease the textures that favor plane stress conditions.

Genetic diversity, aggressiveness and metalaxyl sensitivity of Pythium aphanidermatum populations infecting cucumber in Oman

Seventy three isolates of Pythium aphanidermatum obtained from cucumber from four different regions of Oman and 16 isolates of muskmelon from the Batinah region in Oman were characterized for aggressiveness, sensitivity to metalaxyl and genetic diversity using AFLP fingerprinting. Twenty isolates of P. aphanidermatum from diverse hosts from different countries were also included in the study. Most isolates from Oman were found to be aggressive on cucumber seedlings and all were highly sensitive to metalaxyl (EC50 < 0•80 µg mL−1). Isolates from cucumber and muskmelon were as aggressive as each other on both hosts (P > 0.05), which implies a lack of host specialization in P. aphanidermatum on these two hosts in Oman. AFLP analysis of all isolates using four primer-pair combinations resolved 152 bands, of which 61 (~40%) were polymorphic. Isolates of P. aphanidermatum from Oman and other countries exhibited high genetic similarity (mean = 94.1%) and produced 59 different AFLP profiles. Analysis of molecular variance indicated that most AFLP variation among populations of P. aphanidermatum in Oman was associated with geographical regions (FST = 0.118; P < 0.0001), not hosts (FST = -0.004; P = 0.4323). These data were supported by the high rate of recovery (24%) of identical phenotypes between cucumber and muskmelon fields in the same region as compared to the low recovery (10%) across regions in Oman, which suggests more frequent movement of Pythium inoculum among muskmelon and cucumber fields in the same region compared to movement across geographically separated regions. However, recovering clones among regions and different countries may imply circulation of Pythium inoculum via common sources in Oman and also intercontinental spread of isolates.

Ternary metal complexes of anionic and neutral pyridoxine (vitamin B6) with 2,2'-bipyridine. Syntheses and x-ray structures of (pyridoxinato)bis(2,2'-bipyridyl)cobalt(III) perchlorate and chloro(2,2'-bipyridyl)(pyridoxine)copper(II) perchlorate hydrate

Ternary metal complexes involving vitamin B6 with formulas [CO",(PN-H)](anCdI [OC)'(bpy)(PN)Cl]C10(.bpHy 0 = 2,2'-bipyridine, PN = neutral pyridoxine, PN-H = anionic pyridoxine) have been prepared for the first time and characterized by means of magnetic and spectroscopic measurements. The crystal structures of the compounds have also been determined. [CO(PN-H)](CcryIsOta,l)lize s in the space group P2,/c with a = 18.900 (3) A, b = 8.764 (1) A, c = 20.041 (2) A,p = 116.05 (l)', and Z = 4 and [Cu(bpy)(PN)C1]C104-H20in the space group Pi with a = 12.136 (5) A, b = 13.283 (4) A,c = 7.195 (2) A, a = 96.91 (Z)', 0 = 91.25 (3)', y = 71.63 (3)', and Z = 2. The structures were solved by the heavy-atom method and refined by least-squares techniques to R values of 0.080 and 0.042 for 3401 and 2094 independent reflections, respectively. Both structures consist of monomeric units. The geometry around Co(II1) is octahedral and around Cu(I1) is distorted square pyramidal. In [CO(PN-H)]t(wCo IoxOy~ge)n~s ,fro m phenolic and 4-(hydroxymethyl) groups of PN-H and two nitrogens from each of two bpy's form the coordination sphere. In [Cu(bpy)(PN)C1]C104.H20o ne PN and one bpy, with the same donor sites, act as bidentate chelates in the basal plane, with a chloride ion occupying the apical position. In both structures PN and PN-H exist in the tautomeric form wherein pyridine N is protonated and phenolic 0 is deprotonated. However, a novel feature of the cobalt compound is that PN-H is anionic due to the deprotonation of the 4-(hydroxymethyl) group. The packing in both structures is governed by hydrogen bonds, and in the copper compound partial stacking of bpy's at a distance of -3.55 also adds to the stability of the system. Infrared, NMR, and ligand field spectroscopic results and magnetic measurements are interpreted in light of the structures.

Determinants of farmer retirement and farm succession in Finland

In the past decade, the Finnish agricultural sector has undergone rapid structural changes. The number of farms has decreased and the average farm size has increased when the number of farms transferred to new entrants has decreased. Part of the structural change in agriculture is manifested in early retirement programmes. In studying farmers exit behaviour in different countries, institutional differences, incentive programmes and constraints are found to matter. In Finland, farmers early retirement programmes were first introduced in 1974 and, during the last ten years, they have been carried out within the European Union framework for these programmes. The early retirement benefits are farmer specific and de-pend on the level of pension insurance the farmer has paid over his active farming years. In order to predict the future development of the agricultural sector, farmers have been frequently asked about their future plans and their plans for succession. However, the plans the farmers made for succession have been found to be time inconsistent. This study estimates the value of farmers stated succession plans in predicting revealed succession decisions. A stated succession plan exists when a farmer answers in a survey questionnaire that the farm is going to be transferred to a new entrant within a five-year period. The succession is revealed when the farm is transferred to a suc-cessor. Stated and revealed behaviour was estimated as a recursive Binomial Probit Model, which accounts for the censoring of the decision variables and controls for a potential correlation between the two equations. The results suggest that the succession plans, as stated by elderly farmers in the questionnaires, do not provide information that is significant and valuable in predicting true, com-pleted successions. Therefore, farmer exit should be analysed based on observed behaviour rather than on stated plans and intentions. As farm retirement plays a crucial role in determining the characteristics of structural change in agriculture, it is important to establish the factors which determine an exit from farming among eld-erly farmers and how off-farm income and income losses affect their exit choices. In this study, the observed choice of pension scheme by elderly farmers was analysed by a bivariate probit model. Despite some variations in significance and the effects of each factor, the ages of the farmer and spouse, the age and number of potential successors, farm size, income loss when retiring and the location of the farm together with the production line were found to be the most important determi-nants of early retirement and the transfer or closure of farms. Recently, the labour status of the spouse has been found to contribute significantly to individual retirement decisions. In this study, the effect of spousal retirement and economic incentives related to the timing of a farming couple s early retirement decision were analysed with a duration model. The results suggest that an expected pension in particular advances farm transfers. It was found that on farms operated by a couple, both early retirement and farm succession took place more often than on farms operated by a single person. However, the existence of a spouse delayed the timing of early retirement. Farming couples were found to co-ordinate their early retirement decisions when they both exit through agricultural retirement programmes, but such a co-ordination did not exist when one of the spouses retired under other pension schemes. Besides changes in the agricultural structure, the share and amount of off-farm income of a farm family s total income has also increased. In the study, the effect of off-farm income on farmers retirement decisions, in addition to other financial factors, was analysed. The unknown parameters were first estimated by a switching-type multivariate probit model and then by the simulated maxi-mum likelihood (SML) method, controlling for farmer specific fixed effects and serial correlation of the errors. The results suggest that elderly farmers off-farm income is a significant determinant in a farmer s choice to exit and close down the farm. However, off-farm income only has a short term effect on structural changes in agriculture since it does not significantly contribute to the timing of farm successions.

The structures of ethyl 1,2,2-tricyano-3,3-dimethylcyclopropane-1-carboxylate and ethyl 2',3,3'-tricyanocyclohexanespirocyclopropane-2'-carboxylate

The crystal and molecular structures of C ,,H,IN302 (I) and C14HIsN302 (II) have been determined by direct methods using three-dimensional X-ray diffractometer data. Crystals of (I) are orthorhombic, space group Pna21, with a = 14.662(6), b = 10.492(5), c = 7.375 (3)A, Z = 4, V = 1134.5 A 3, D O = 1.25 (by flotation), D e = 1.269 Mgm -a, g(MoKa) = 0.085 mm -1. Crystals of (II) are monoclinic, space group P21/a, with a = 7.886 (5), b = 22.011 (8), c = 8.100 (3) A, fl = 103.12 (5) °, Z = 4, V = 1369.2 A 3, D O = 1.23 (by flotation), D e = 1.255 Mg m -3, g(Mo Kct) = 0.080 mm -1. Least-squares full-matrix refinement based on 782 (I) and 1400 independent reflections (II) converged at R = 0.040 (I) and 0.042 (II). The effect of electron-withdrawing substituents on the geometry of the cyclopropane ring is discussed.

Intrahepatic cholestasis of pregnancy : genetic background, epidemiology and hepatobiliary consequences

Intrahepatic cholestasis of pregnancy (ICP) is the most common cholestatic liver disease during pregnancy. The reported incidence varies from 0.4 to 15% of full-term pregnancies. The etiology is heterogeneous but familial clustering is known to occur. Here we have studied the genetic background, epidemiology, and long-term hepatobiliary consequences of ICP. In a register-based nation-wide study (n=1 080 310) the incidence of ICP was 0.94% during 1987-2004. A slightly higher incidence, 1.3%, was found in a hospital-based series (n=5304) among women attending the University Hospital of Helsinki in 1992-1993. Of these 16% (11/69) were familial and showed a higher (92%) recurrence rate than the sporadic (40%) cases. In the register-based epidemiological study, advanced maternal age and, to a lesser degree, parity were identified as new risk factors for ICP. The risk was 3-fold higher in women >39 years of age compared to women <30 years. Multiple pregnancy also associated with an elevated risk. In a genetic study we found no association of ICP with the genes regulating bile salt transport (ABCB4, ABCB11 and ATP8B1). The livers of postmenopausal women with a history of ICP tolerated well the short-term exposure to oral and transdermal estradiol, although the doses used were higher than those in routine clinical use. The response of serum levels of sex hormone-binding globulin (SHBG) to oral estradiol was slightly reduced in the ICP group. Transdermal estradiol had no effect on C-reactive protein (CRP) or SHBG. A number of liver and biliary diseases were found to be associated with ICP. Women with a history of ICP showed elevated risks for non-alcoholic liver cirrhosis (8.2 CI 1.9-36), cholelithiasis and cholecystitis (3.7 CI 3.2-4.2), hepatitis C (3.5 CI 1.6-7.6) and non-alcoholic pancreatitis (3.2 CI 1.7-5.7). In conclusion, ICP complicates around 1% of all full-term pregnancies in Finland and its incidence has remained unchanged since 1987. It is familial in 16% of cases with a higher recurrence rate. Although the cause remains unknown, several risk factors, namely advanced maternal age, parity and multiple pregnancies, can be identified. Both oral and transdermal regimens of postmenopausal hormone therapy (HT) are safe for women with a history of ICP when liver function is considered. Some ICP patients are at risk of other liver and biliary diseases and, contrary to what has been thought, a follow-up is warranted.

How pantothenol intervenes in Coenzyme-A biosynthesis of Mycobacterium tuberculosis

Coenzyme A is an indispensable cofactor for all organisms and holds a central position in a number of pathways. Prokaryotic enzymes involved in the synthesis of CoA are quite different from their mammalian counterparts; hence, they are good targets for the development of antimicrobials to treat many diseases. There are antimicrobials that act by inhibiting CoA biosynthesis. It has been suggested that pantothenol exhibits antibacterial activity by competitively inhibiting pantothenate kinase, a key regulatory enzyme for CoA synthesis. Contrary to these suggestions, in this paper, we demonstrate that pantothenol acts as a substrate for Mycobacterium tuberculosis and Escherichia coli pantothenate kinases. The product, 4'-phosphopantothenol, thus formed inhibits competitively the utilization of 4'-phosphopantothenate by CoaBC. Thus, it is the failure of CoaBC to utilize 4'-phosphopantothenol as a substrate that accounts for the bactericidal activity of pantothenol. (C) 2007 Elsevier Inc. All rights reserved.

Effect of directionality of unidirectional grinding marks on friction and transfer layer formation of Mg on steel using inclined scratch test

Surface topography has been known to play an important role in the friction and transfer layer formation during sliding. In the present investigation, EN8 steel flats were ground to attain different surface roughness with unidirectional grinding marks. Pure Mg pins were scratched on these surfaces using an Inclined Scratch Tester to study the influence of directionality of surface grinding marks on coefficient of friction and transfer layer formation. Grinding angle (i.e., the angle between direction of scratch and grinding marks) was varied between 0 degrees and 90 degrees during the tests. Experiments were conducted under both dry and lubricated conditions. Scanning electron micrographs of the contact surfaces of pins and flats were used to reveal the surface features that included the morphology of the transfer layer. It was observed that the average coefficient of friction and transfer layer formation depend primarily on the directionality of the grinding marks but were independent of surface roughness on the harder mating surface. In addition, a stick-slip phenomenon was observed, the amplitude of which depended both on the directionality of grinding marks and the surface roughness of the harder mating surface. The grinding angle effect on the coefficient of friction, which consists of adhesion and plowing components, was attributed to the variation of plowing component of friction. (c) 2006 Elsevier B.V. All rights reserved.

Structural Studies of Analgesics and Their Interactions. V.* The Crystal and Molecular Structure of Metamizol Monohydrate

Metamizol, Na[Ct3H16N3045], C13H16N304S-Na +, a sulphonyl derivative of amidopyrine, is perhaps the most widely used non-narcotic analgetic and antiinflammatory pyrazolone derivative. The monohydrate of the compound crystallizes in the monoclinic space group P2Jc with eight molecules in a unit cell of dimensions a = 9.143 (3), b = 49.50 (2), c = 7.314 (2)/k and fl = 90.9 (1) °. The structure was solved by direct methods and refined to an R value of 0.080 for 4466 observed reflections. The two crystallographically independent molecules in the structure have similar dimensions. The elongated molecules are hydrophobic at one end and hydrophilic at the other with the middle portion partly hydrophobic and partly hydrophilic. The pyrazolone group in the structure has dimensions similar to those found in uncomplexed antipyrine and amidopyrine. The crystal structure can be described as consisting of double layers of metamizol molecules stacked perpendicular to the b axis. The adjacent double layers are separated by a layer of Naions and water molecules.

Syntheses, spectroscopy, structures, and conformations of .lambda.3-cyclotriphosphazanes: role of negative hyperconjugation

The reactions of As-chlorocyclotriphosphazane [EtNPCl], with phenols or trifluoroethanol yield the respective aryloxy- or trifluoroethoxy-containingX 3-cyclotriphosphazanes [EtNP(OR)]3 (R = C6H4Br-4 (2),C 6H5 (3C,6 H3-Mez-3,5 (4), C6H3Mez-2,6 (5), CH2CF3 (6)) as their cis-transisomericmixtures. The products have beencharacterized by IRand NMRspectroscopy. Thecrystalstructuresofboth thecis (2a) and trans(2b) isomer_softhep-bromophenoxy derivative have been determined by X-ray diffraction. Crystal data for 2a: triclinic, P1, a = 9.872(4) A, b = 13.438(6) A, c = 13.548(8) A, CY = 117.02(5)', 0 = 96.00(6)', y = 105.38(4)O, Z = 2, final R = 0.080. Crystal data for 2b: monoclinic, P21/n, a = 12.721(6) A, b = 13.468(7) A, c = 17.882(5) A, /3 = 101.62(3)O, Z = 4, final R = 0.066. The cis isomer exhibits a chair-triaxial conformation and the trans isomer a boat-triaxial conformation. Conformational preferences of X3-cyclotriphosphazanes have been probed by both MNDO and ab initio calculations on model systems [HNPXIp (X = H, F). In addition to vicinal lone pair repulsions, negative hyperconjugative interactions involving the nitrogen lone pairs and adjacent P-X Q* orbitals are found to be important (especially when X is an electronegative substituent) in determining the conformational preferences of X3-cyclotriphosphazanes. The calculations also show that the axial - equatorial conversion at phosphorus has a large activation barrier in these systems

Reactivity Of Pph3 Toward Ru2cl(O2cme)4 - Synthesis And X-Ray Crystal-Structure Of [Ru(O2cme)(Mecn)2(Pph3)2](Clo4)

A new ruthenium(II) complex of the type [Ru(O2CMe)(MeCN)2(PPh3)2](CiO4) (1) has been isolated from a reaction between Ru2Cl(O2CMe), and PPh3 in MeCN followed by the addition of NaClO4. The structure of 1 is determined by single crystal X-ray studies. The crystal belongs to the monoclinic space group C2/m with the following unit cell dimensions for the C42H39N2O6P2ClRu(M = 866.15): a = 23.295(1)angstrom, b = 23.080(1)angstrom, c = 9.159(1)angstrom, beta = 107.32(1)-degrees, V = 4701(1)angstrom3, Z = 4, D(c) = 1.224 gcm-3, lambda(Mo - K-alpha) = 0.7107 angstrom, mu(Mo - K-alpha) = 4.09 cm-1, T = 293K, R = 0.081 (R(w) = 0.094) for 2860 reflections with I greater-than-or-equal-to 3-sigma(I) and g = 0.015853. In the complex cation, the symmetry about the metal centre is essentially octahedral showing the presence of a chelating acetato, two cis-oriented MeCN and two trans-disposed PPh3 ligands. The mechanistic aspects of the core cleavage reaction are discussed.

Response of Materials during sliding on various surface textures

In the present investigation, basic studies were conducted using Inclined pin-on-plate sliding Tester to understand the role of surface texture of hard material against soft materials during sliding. Soft materials such as Al-Mg alloy, pure Al and pure Mg were used as pins and 080 M40 steel was used as plate in the tests. Two surface parameters of steel plates — roughness and texture — were varied in tests. It was observed that the transfer layer formation and the coefficient of friction which has two components, namely adhesion and plowing component, are controlled by the surface texture of harder material. For the case of Al-Mg alloy, stick-slip phenomenon was absent under both dry and lubricated conditions. However, for the case of Al, it was observed only under lubricated conditions while for the case of Mg, it was observed under both dry and lubricated conditions. Further, it was observed that the amplitude of stick-slip motion primarily depends on plowing component of friction. The plowing component of friction was highest for the surface that promotes plane strain conditions near the surface and was lowest for the surface that promotes plane stress conditions near the surface.

Efficient synthesis of carbonyl compounds: oxidation of azides and alcohols catalyzed by vanadium pentoxide in water using tert-butylhydroperoxide

Catalytic amount of vanadium reagent with tert-butylhydroperoxide as the oxidant was found to be an excellent oxidizing agent in aqueous medium. Vanadium pentoxide with aq tert-butylhydroperoxide readily oxidizes primary benzylic azides to the corresponding acids and secondary benzylic azides to the corresponding ketones in excellent yields. Further, vanadium pentoxide and aq tert-butylhydroperoxide combination turned out to be an effective catalyst for the oxidation of alcohols. Using vanadium pentoxide and aq tert-butylhydroperoxide primary alcohols were oxidized to the corresponding acids, whereas secondary alcohols underwent a smooth transformation to furnish corresponding ketones in excellent yields. All the oxidations are performed in water. (C) 2011 Elsevier Ltd. All rights reserved.

Mixed ionic and electronic conduction in zirconia and its applications in metallurgy

Mixed ionic and electronic conduction in Zr02-based solid electrolytes was studied.The effect of impurities and second-phase particles on the mixed conduction parameter, P,, was measured for different types of ZrOZ electrolytes. The performance of solid-state sensors incorporating ZrOZ electrolytes is sometimes limited by electronic conduction in ZrOZ, especially at temperatures >I800 K. Methods for eliminating or minimizing errors in measured emf due to electronically driven transport of oxygen anions are discussed. Examples include probes for monitoring oxygen content in liquid steel as well as the newly developed sulfur sensor based on a ZrOz(Ca0) + CaS electrolyte. The use of mixed conducting ZrOZ as a semipermeable membrane or chemically selective sieve for oxygen at high temperatures is discussed. Oxygen transport from liquid iron to CO + C& gas mixtures through a ZrOZ membrane driven by a chemical potential gradient, in the absence of electrical leads or imposed potentials, was experimentally observed.