Determining relative rates of cellulose dissolution in ionic liquids through in situ viscosity measurement

Using in situ viscosity measurement, the rate of cellulose dissolution in a number of ionic liquids has been determined allowing their performance as solvents to be quantitatively assessed. 1-Butyl-3-methylimidazolium ethanoate was shown to dissolve cellulose faster than analogous ionic liquids with chloride or dimethylphosphate anions. Analysis of the data highlights the influence of both anion basicity and relative concentration on the rate of dissolution.

Microwave Irradiation for the Facile Synthesis of Transition-Metal Nanoparticles (NPs) in Ionic Liquids (ILs) from Metal-Carbonyl Precursors and Ru-, Rh-, and Ir-NP/IL Dispersions as Biphasic Liquid-Liquid Hydrogenation Nanocatalysts for Cyclohexene

Stable chromium, molybdenum, tungsten, manganese, rhenium, ruthenium, osmium, cobalt, rhodium, and iridium metal nanoparticles (MNPs) have been reproducibly obtained by facile, rapid (3 min), and energysaving 10 W microwave irradiation (MWI) under an argon atmosphere from their metal–carbonyl precursors [Mx(CO)y] in the ionic liquid (IL) 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIm][BF4]). This MWI synthesis is compared to UV-photolytic (1000 W, 15 min) or conventional thermal decomposition (180–2508C, 6–12 h) of [Mx(CO)y] in ILs. The MWIobtained nanoparticles have a very small (<5 nm) and uniform size and are prepared without any additional stabilizers or capping molecules as long-term stable M-NP/IL dispersions (characterization by transmission electron microscopy (TEM), transmission electron diffraction (TED), and dynamic light scattering (DLS)). The ruthenium, rhodium, or iridium nanoparticle/IL dispersions are highly active
and easily recyclable catalysts for the biphasic liquid–liquid hydrogenation of cyclohexene to cyclohexane with activities of up to 522 (mol product)(mol Ru)1h1 and 884 (mol product)(molRh)1h1 and give almost quantitative conversion within 2 h at 10 bar H2 and 908C. Catalyst poisoning experiments with CS2 (0.05 equiv per Ru) suggest a heterogeneous surface catalysis of RuNPs.

Dioxouranium(VI) extraction in microchannels using ionic liquids

The extraction of uranium(VI) from aqueous nitric acid solutions by tributylphosphate {TBP; 30%(v/v)} dissolved in the ionic liquid 1-butyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl}amide was investigated. The experiments were performed in a Teflon microchannel of 0.5 mm internal diameter, while the dioxouranium(VI) concentrations in the aqueous and the ionic liquid phases were determined by UV-Vis spectroscopy. The effects of initial nitric acid concentration (0.01-3 M), residence time, and phase flow rate ratio were studied. It was found that, with increasing nitric acid concentration, the percentage of dioxouranium(VI) extracted decreased and then increased again, while the extraction efficiency followed a slightly different trend. Overall mass transfer coefficients varied between 0.049 s and 0.312 s . © 2012 Elsevier B.V. All rights reserved.

Flow patterns and pressure drop of ionic liquid-water two-phase flows in microchannels

The two-phase flow of a hydrophobic ionic liquid and water was studied in capillaries made of three different materials (two types of Teflon, FEP and Tefzel, and glass) with sizes between 200µm and 270µm. The ionic liquid was 1-butyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl}amide, with density and viscosity of 1420kgm and 0.041kgms, respectively. Flow patterns and pressure drop were measured for two inlet configurations (T- and Y-junction), for total flow rates of 0.065-214.9cmh and ionic liquid volume fractions from 0.05 to 0.8. The continuous phase in the glass capillary depended on the fluid that initially filled the channel. When water was introduced first, it became the continuous phase with the ionic liquid forming plugs or a mixture of plugs and drops within it. In the Teflon microchannels, the order that fluids were introduced did not affect the results and the ionic liquid was always the continuous phase. The main patterns observed were annular, plug, and drop flow. Pressure drop in the Teflon microchannels at a constant ionic liquid flow rate, was found to increase as the ionic liquid volume fraction decreased, and was always higher than the single phase ionic liquid value at the same flow rate as in the two-phase mixture. However, in the glass microchannel during plug flow with water as the continuous phase, pressure drop for a constant ionic liquid flow rate was always lower than the single phase ionic liquid value. A modified plug flow pressure drop model using a correlation for film thickness derived for the current fluids pair showed very good agreement with the experimental data. © 2013 Elsevier Ltd.

Pinning down the solid-state polymorphism of the ionic liquid [bmim][PF6]

The solid-state polymorphism of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate, [bmim][PF6], has been investigated via low-temperature and high-pressure crystallisation experiments. The samples have been characterised by single-crystal X-ray diffraction, optical microscopy and Raman spectroscopy. The solid-state phase behaviour of the compound is confirmed and clarified with respect to previous phase diagrams. The structures of the previously reported gamma-form, which essentially exhibits a G'T cation conformation, as well as those of the elusive beta- and alpha-forms, are reported. Crystals of the beta-phase are twinned and the structure is heavily disordered; the cation conformation in this form is predominantly TT, though significant contributions from other less frequently encountered conformers are also observed at low temperature and high pressure. The cation conformation in the alpha-form is GT; the presence of the G'T conformer at 193 K in this phase can be eliminated on cooling to 100 K. Whilst X-ray structural data are overall in good agreement with previous interpretations based on Raman and NMR studies, they also reveal a more subtle interplay of intermolecular interactions, which give rise to a wider range of conformers than previously considered.

Rheological and heat transfer behaviour of the ionic liquid, [C(4)mim][NTf2]

Systematic experiments have been carried out on the thermal and rheological behaviour of the ionic liquid, 1-butyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl} imide, [C(4)mim][NTf2], and, for the first time, on the forced convective heat transfer of an ionic liquid under the laminar flow conditions. The results show that the thermal conductivity of the ionic liquid is similar to 0.13 W m(-1) K-1, which is almost independent of temperature between 25 and 40 degrees C. Rheological measurements show that the [C(4)mim][NTf2] liquid is a Newtonian fluid with its shear viscosity decreasing with increasing temperature according to the exponential law over a temperature range of 20-90 degrees C. The convective heat transfer experiments demonstrate that the thermal entrance length of the ionic liquid is very large due to its high viscosity and low thermal conductivity. The convective heat transfer coefficient is observed to be much lower than that of distilled water under the same conditions. The convective heat transfer data are also found to fit well to the convectional Shah's equation under the conditions of this work. (C) 2007 Elsevier Inc. All rights reserved.

High pressure CO2 absorption studies on imidazolium-based ionic liquids:Experimental and simulation approaches

A combined experimental-computational study on the CO absorption on 1-butyl-3-methylimidazolium hexafluophosphate, 1-ethyl-3-methylimidazolium bis[trifluoromethylsulfonyl]imide, and 1-butyl-3-methylimidazolium bis[trifluoromethylsulfonyl]imide ionic liquids is reported. The reported results allowed to infer a detailed nanoscopic vision of the absorption phenomena as a function of pressure and temperature. Absorption isotherms were measured at 318 and 338K for pressures up to 20MPa for ultrapure samples using a state-of-the-art magnetic suspension densimeter, for which measurement procedures are developed. A remarkable swelling effect upon CO absorption was observed for pressures higher than 10MPa, which was corrected using a method based on experimental volumetric data. The experimental data reported in this work are in good agreement with available literature isotherms. Soave-Redlich-Kwong and Peng-Robinson equations of state coupled with bi-parametric van der Waals mixing rule were used for successful correlations of experimental high pressure absorption data. Molecular dynamics results allowed to infer structural, energetic and dynamic properties of the studied CO+ionic liquids mixed fluids, showing the relevant role of the strength of anion-cation interactions on fluid volumetric properties and CO absorption. © 2012 Elsevier B.V.

On the scaling behavior of electric conductivity in [C(4)mim][NTf2]

In this work we examine, for the first time, the molar conductivity behavior of the deeply supercooled room temperature ionic liquid [C₄mim][NTf₂] in the temperature, pressure and volume thermodynamic space in terms of density scaling (TV^γ)⁻¹ combined with the equation of state (EOS). The exponent γ_σ determined from the Avramov model analysis is compared with the coefficient obtained from the viscosity studies carried out at moderate temperatures. Therefore, the experimental results presented herein provide the answer to the long-standing question regarding the validity of thermodynamic scaling of ionic liquids over a wide temperature range, i.e. from the normal liquid state to the glass transition point. Finally, we investigate the relationship between the dynamic and thermodynamic properties of [C₄mim][NTf₂] represented by scaling exponent γ and Grüneisen constant γ_G, respectively.

Acoustic and Volumetric Properties of Diluted Solutions of Water in Ionic Liquids

Herein, we report the densities and speeds of sound in binary mixtures of three hydrophobic and one hydrophilic ionic liquids: 1-butyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide, [C4mim][NTf2], 1-butyl-1-methylpyrrolidinium bis[(trifluoromethyl)sulfonyl]imide, [C4mpyr][NTf2], 1-propyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide, [C3mim][NTf2] and 1-ethyl-3-methylimidazolium thiocyanate, [C2mim][SCN], with water at 298.15 K and 0.1 MPa. The concentration range of water, which encompassed relatively small values well below the saturation point, is often regarded as an impurity for hydrophobic ionic liquids. On the basis of experimental results the molar volume, adiabatic molar compressibility, partial molar volume and apparent molar volume, as well as, partial molar and apparent molar isentropic compressibility properties were then calculated. Interesting results are obtained using the solutions based on the hydrophilic [C2mim][SCN], since these mixtures are characterized by relatively low density and high values of speed of sound. Furthermore, the partial molar volumes and partial molar adiabatic compressibilities of water in solution with [C2mim][SCN] are the lowest among the investigated in mixtures with ionic liquids. However, in the case of the hydrophobic ionic liquid solutions, only small differences are observed for molar adiabatic compressibilities with the change of the cation structure, i.e. for water + [C4mim][NTf2] or + [C4mpyr][NTf2]. A more pronounced difference has been observed for the partial molar compressibility of water in solutions with these two ionic liquids.

Olefin / Paraffin separation using Task-Specific Materials based on Ionic Liquids: Advances in Gas Processing

In this work, 1-hexene was extracted from its mixtures with n-hexane in varying ratios using a task specific ionic liquid. Herein, the ionic liquid (IL) 1-butyl-3-methylimidazolium nitrate, [BMIM][NO3], was used and examined with and without the addition of a metal salt. The impact of water on both selectivity and distribution coefficient was also tested. Four potential metal salts were investigated, the results of which demonstrate that the dissolution of transition-metal salts in the IL improves the separation of 1-hexene from n-hexane through metal-olefin complexation. Additionally, the presence of water in IL solutions containing metal salt enhances this selectivity. Finally, UNIFAC was used to correlate the experimental LLE data with good accuracy.

Process for the preparation of heterocyclyl chalcogenones via reaction of elemental sulfur, selenium, or tellurium with heterocyclic cationic species.

Heterocyclic chalcogenones were prepd. by reaction of S, Se, or Te with ionic liqs. or salts [I; Ra = (substituted) alkyl, cycloalkyl, aryl, aralkyl, alkylaryl; Q = (unsatd.) (substituted) linker to form a ring of 5-10 members; X- = anion selected from conjugate bases of HX having a pKa value of >2.5]. Thus, 1-butyl-3-methylimidazolium acetate was heated with stoichiometric S at 75° for 48 h to give 1-butyl-3-methylimidazole-2-thione. [on SciFinder(R)]

Regenerated cellulose matrix-encapsulated active substances and method therefor.

The process involves encapsulation or immobilization of the active solid substance in a cellulose framework by regenerating cellulose dissolved in an ionic liq. solvent in a regenerating soln. The active substance can be initially present in the ionic liq. or in the regenerating solvent either as a soln. or dispersion. The invention is applicable to mol. encapsulation and to entrapping of larger particles including enzymes, nanoparticles and macroscopic components, and to the formation of bulk materials with a wide range of morphol. forms. Thus, carbamoylmethylphosphine oxide (I) encapsulated in a cellulose matrix was realized by adding I to a 10% soln. of cellulose in 1-butyl-3-methylimidazolium chloride (ionic liq.) under vigorous stirring and then removing the ionic liq. with water. [on SciFinder(R)]

Ionic liquid reconstituted cellulose composites as solid support matrices with good transparency for biocatalytic reaction.

Disclosed are composites comprising regenerated cellulose, a first active substance, a second active substance, and a linker. Thus, microcryst. cellulose was dissolved in 1-butyl-3-methylimidazolium chloride using microwave pulse heating at 120-150°, cooled to 60° to form a super-cooled liq., 20% (based on cellulose) poly(L-lysine hydrobromide) was added therein, homogenized, cast onto a glass plate, the resulting film soaked in water for at least 24 h to leach residual from the film to give a reconstituted cellulose film, showing good transparency. [on SciFinder(R)]

Síntese e estudos estruturais de novos materiais luminescentes

A presente dissertação teve como objectivo a síntese, caracterização e estudo das propriedades luminescentes de complexos livres e/ou imobilizados no material mesoporoso MCM-41. Na primeira parte estudaram-se complexos do tipo, Eu(NTA)3L2, onde NTA corresponte ao β-dicetonato 1-(2-naftoil)-3,3,3-trifluoro-acetonato, e L2 aos ligandos bidentados de azoto derivados do pirazolilpiridina e L aos ligandos monodentados (etil-4-piridilacetato, água, piridina e metilfenilsulfóxido). Alguns destes ligandos foram imobilizados e/ou impregnados no MCM-41, tendo-se posteriormente complexado o fragmento Eu(NTA)3. Na segunda parte estudou-se o efeito do contra-ião no complexo C[Eu(NTA)4], usando os catiões (C): tetrabutilamónio [NBu4]+, 1-butil-3-metilimidazolilo [C4mim]+ e 1-butil-3-metilpiridínio [C4mpy]+. O anião [Eu(NTA)4]- foi imobilizado no MCM-41 derivatizado com grupos 1-propil-3-metilimidazolilo. Todos os complexos preparados foram caracterizados pelas técnicas de análise elementar, termogravimetria, espectroscopias vibracionais (Infravermelho e Raman) e de ressonância magnética nuclear, e os materiais preparados foram adicionalmente analisados por difracção de raios-X de pós e ressonância magnética nuclear de estado sólido. Foram também estudadas as propriedades fotoluminescentes dos compostos, e para facilitar a análise dos resultados, nalguns casos foram preparados e caracterizados os compostos análogos de gadolínio.

Novos materiais com polioxotungstatos substituídos com metais d e f

The present work reports studies on the new compounds obtained by the combination of polyoxoanions derived from the Keggin and Lindquist structures with several cations. The studies were first focused on the monolacunary Keggin polyoxoanions [PW11O39M(H2O)]n- (M = FeIII, MnIII and n = 4; M = CoII and n = 5) and its combination with the organic cation 1-butyl-3-methylimidazolium (Bmim+). The association of Bmim+ cation with the polyoxoanion [PW11O39Fe(H2O)]4- allowed to isolate for the first time both the monomeric and the dimeric [PW11O39Fe)2O]10- anions, with the same cation and using simple bench techniques by pH manipulation. Studies regarding the stability of these inorganic species in solution indicated that both species are present in solution in equilibrium. However, the inability to up until now isolate the dimeric unit through simple bench methods, lead to the hypothesis that the cation had a role to play in the selective precipitation of either the monomer or the dimer. Repetition of the same procedures with the polyoxoanions [SiW11O39Fe(H2O)]5- and [PW11O39M(H2O)]n- (M = FeIII, MnIII and n = 4; M = Co and n = 5), afforded only the corresponding monomeric compounds, (Bmim)5[SiW11O39FeIII(H2O)]· 4H2O (3), (Bmim)5[PW11O39CoII(H2O)]· 0.5 H2O, (4) and (Bmim)5[PW11O39MnIII(H2O)]· 0.5 H2O (5). Moreover, the combination of Bmim+ and the polyoxotungstate [PW11O39Co(H2O)]5- afforded two different crystal structures, depending on the synthetic conditions. Thus, a ratio Bmim+:POM of 5:1 and the presence of K+ cations (due to addition of KOH) led to a formula Na2K(Bmim)2[PW11.2O39Co0.8(H2O)]·7H2O (4a), whilst a ratio Bmim:POM of 7:1 led to the formation of a crystal with the chemical formula Na2(Bmim)8[PW11O39Co(H2O)]2·3H2O (4b). Electrochemical studies were performed with carbon paste electrodes modified with BmimCl to investigate the influence of the Bmim+ cation in the performance of the electrodes. The voltametric measurements obtained from solutions containing the anions [PW11O39]7- and [SiW11O39]8- are presented. Results pointed to an improvement of the acquired voltametric signal with a slight addition of BmimCl (up to 2.5% w/w), specially in the studies regarding pH variation. Additional synthesis were carried out with both the cations Omim+ and THTP+.