Measurement of water surface roughness and wind shear stress by the use of a pitot tube in a laboratory wave channel /

Mode of access: Internet.

Characterization of Chimney Flue Gas Flows : Flow Rate Measurements with Averaging Pitot Probes

Performance testing methods of boilers in transient operating conditions (start, stop and combustion power modulation sequences) need the combustion rate quantified to allow for the emissions to be quantified. One way of quantifying the combustion rate of a boiler during transient operating conditions is by measuring the flue gas flow rate. The flow conditions in chimneys of single family house boilers pose a challenge however, mainly because of the low flow velocity. The main objectives of the work were to characterize the flow conditions in residential chimneys, to evaluate the use of the Pitot-static method and the averaging Pitot method, and to develop and test a calibration method for averaging Pitot probes for low

Ultrasound velocity profile (UVP) measurements in shallow open-channel flows

1st European IAHR Congress, 6-4 May, Edinburgh, Scotland

Kipsilevyn kuivaamisessa tarvittavan puhallutettavan ilmamäärän ja ohjauksen optimointi

Tämä insinöörityö on tehty Saint-Gobain Rakennustuotteet Oy:n Kirkkonummen tehtaan kipsilevyjen kuivauksessa käytettävästä kuivurista. Kuivurissa on monta erilaista tekijää, jotka vaikuttavat kuivumiseen. Työssä keskitytään ilmavirtauksien optimoimiseen tasokohtaisesti kuivurin sisällä. Kuivurissa on kahdeksan tasoa, joilta jokaiselta voi tulla eri tavalla kuivuneita kipsilevyjä. Tämä johtuu tasoilla olevista erilaisista olosuhteista. Tasojen lisäksi on kuivurissa myös kuusi vyöhykettä, jotka ovat rakenteeltaan erilaisia. Tämän työn tarkoituksena on jakaa ilmavirtaukset tasokohtaisesti mahdollisimman tasaisiksi. Ilmavirtausten jakautumista voidaan muuttaa säätöpelleillä, joiden jälkeen ilmavirtaus kulkeutuu kanavia pitkin tasoille. Eri vyöhykkeiden säätöpellit ja ilmakanavat eroavat toisistaan, minkä takia säätöpeltien asennot eivät ole samoja eri vyöhykkeillä. Säätöpeltiä avaamalla tai sulkemalla lisätään tai vähennetään ilmavirtausta. Ilmavirtausten muutokset mitattiin ilmavirtausmittarilla ja pitot-putkella. Mittauspisteet sijaitsivat kuivurin sivuilla. Ensimmäisellä vyöhykkeellä ei ollut tasokohtaisia mittauspisteitä, minkä takia sieltä ei voinut mitata tasokohtaisia virtauksia. Toisella, kolmannella ja viidennellä vyöhykkeillä mittauspisteet olivat tuloilmapuolella. Neljännellä vyöhykkeellä mittauspisteet sijaitsivat poistoilmapuolella ja kuudennella vyöhykkeellä mittauspisteitä ei ollut tehty. Työn alussa käsitellään kuivauksen teoriaa ja siihen vaikuttavia tekijöitä. Keskiosassa kerrotaan kuivureiden toiminnasta yleisesti, minkä jälkeen tarkastellaan Kirkkonummen tehtaan kuivurin toimintaa. Loppuosassa esitellään mittaustulokset ilmavirtauksien jakautumisista tasoille. Tuloksissa kerrotaan, kuinka ilmavirtaukset jakautuivat tasoille eri vyöhykkeillä ennen työn aloittamista. Testimittauksien tuloksista havaitaan, miten ilmavirtaus jakaantuu silloin, kun säätöpellit ovat testimittauasennoissa. Testimittausten ansiosta saatiin selville, kuinka säätöpeltien asentoja tulisi muuttaa, jotta tasojen virtaukset olisivat yhtä suuria. Muutosten jälkeen ilmavirtauksista saatiin tasaisemmat.

Fluid dynamics of air in a packed bed: velocity profiles and the continuum model assumption

Air flow through packed beds was analyzed experimentally under conditions ranging from those that reinforce the effect of the wall on the void fraction to those that minimize it. The packing was spherical particles, with a tube-to-particle diameter ratio (D/dp) between 3 and 60. Air flow rates were maintained between 1.3 and 4.44 m3/min, and gas velocity was measured with a Pitot tube positioned above the bed exit. Measurements were made at various radial and angular coordinate values, allowing the distribution of air flow across the bed to be described in detail. Comparison of the experimentally observed radial profiles with those derived from published equations revealed that at high D/dp ratios the measured and calculated velocity profiles behaved similarly. At low ratios, oscillations in the velocity profiles agreed with those in the voidage profiles, signifying that treating the porous medium as a continuum medium is questionable in these cases.

Desenvolvimento de um circuito eletrônico experimental de anemômetro de fio quente

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo teórico e experimental das curvas características de um ventilador axial aplicado em pulverização agrícola

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo experimental de um reator de gaseificação em um leito fixo de açaí

Um leito de gaseificação de pequena escala foi projetado, construído e operado com o objetivo de investigar os parâmetros que influenciam o processo de gaseificação de um leito fixo de caroço de açaí. O reator é do tipo topo aberto downdraft estratificado, de dimensões de 15 cm de diâmetro interno por 1,5 m de altura, com isolamento térmico. O gás produzido foi coletado a jusante do leito de gaseificação e condensado para remoção de alcatrão, o qual foi posteriormente quantificado em titulador Karl Fisher. Após remoção do alcatrão o gás foi introduzido em um Micro GC para quantificação dos percentuais molares de H², CO, N² e CH⁴. O perfil de temperatura do leito foi medido com termopares tipo K posicionados ao longo do eixo longitudinal do leito em distâncias de 10 cm. A vazão de ar foi medida com auxilio de um tubo de Pitot e um micromanômetro. As aquisições dos dados de temperatura foram feitas por um data logger e vazão mássica do ar sendo feita usando comunicação RS232 do micromanômetro. Os procedimentos experimentais foram feitos ao longo de 4 horas de operação do leito de gaseificação, com consumo médio de biomassa de 1,6 kg/h, com 6 dados do perfil de temperatura, vazão mássica de ar, perda de carga do leito e concentração dos gases obtidos no processo de gaseificação e quantificação do teor de alcatrão condensável presente no gás. Verificou-se que o gaseificador de leito de açaí pode ser operado através de uma gama bastante ampla de taxas de fluxo de ar de 2 a 5 kg/h, com a quantidade de energia do gás produzido variando de 5 a 15 MJ/h. As concentrações típicas dos gases obtidos no leito foram de 13% de H², 11% de CO, 1,3% de CH⁴. A eficiência máxima de gás frio de 57% e teor médio de alcatrão de 155 g/m³.

Theoretical and experimental study of agricultural spraying using CFD

This paper presents a computational fluid dynamics (CFD) application about the axial fan design used in an agricultural spraying system with a theoretical and experimental analysis of comparative results between the characteristic curves of a fan for several rotations and numerical results for the influence of blade attack angle variation and optimization of the spraying system, both for a same rotation. Flow was considered three-dimensional, turbulent, isothermal, viscous and non-compressible in a steady state, disregarding any influence of the gravity field. The average turbulent field was obtained from the application of time average where the turbulence model required for closing the set of equations was the k-E model. Resolution of all connected phenomena was achieved with the help of a fluid dynamics computer, CFX, which uses the finite volumes technique as a numerical method. In order to validate the theoretical analysis, an experiment was conducted in a circular section of a horizontal wind tunnel, using a Pitot tube for pressure readings. The main results demonstrate that the methodology used, based on CFD techniques, is able to reproduce the phenomenological behavior of an axial fan in a spraying system because results were very reliable and similar to experimentally measured ones.

Methodology for instantaneous average exhaust gas mass flow rate measurement

This paper presents a new methodology for measurement of the instantaneous average exhaust mass flow rate in reciprocating internal combustion engines to be used to determinate real driving emissions on light duty vehicles, as part of a Portable Emission Measurement System (PEMS). Firstly a flow meter, named MIVECO flow meter, was designed based on a Pitot tube adapted to exhaust gases which are characterized by moisture and particle content, rapid changes in flow rate and chemical composition, pulsating and reverse flow at very low engine speed. Then, an off-line methodology was developed to calculate the instantaneous average flow, considering the ?square root error? phenomenon. The paper includes the theoretical fundamentals, the developed flow meter specifications, the calibration tests, the description of the proposed off-line methodology and the results of the validation test carried out in a chassis dynamometer, where the validity of the mass flow meter and the methodology developed are demonstrated.

The measurement of Pitot pressure in high enthalpy expansion tubes

Expansion tubes operating at total flow enthalpies of 100 MJ kg(-1) or more have characteristical test times of 30-50 mus. Under these conditions, the response time of the Pitot pressure measuring device is critical when performing flow calibration studies. The conventional technique of using a commercial pressure transducer protected by shielding has not always proven to be effective, due to the relatively large (and variable) response time caused by the shielding. A device called the stress wave bar gauge has been designed and calibrated and shown to be an effective way to measure the Pitot pressure with a response time of only 2-3 mus.

Numerical analysis of gas and micro-particle interactions in a hand-held shock-tube device

A unique hand-held gene gun is employed for ballistically delivering biomolecules to key cells in the skin and mucosa in the treatment of the major diseases. One of these types of devices, called the Contoured Shock Tube (CST), delivers powdered micro-particles to the skin with a narrow and highly controllable velocity distribution and a nominally uniform spatial distribution. In this paper, we apply a numerical approach to gain new insights in to the behavior of the CST prototype device. The drag correlations proposed by Henderson (1976), Igra and Takayama (1993) and Kurian and Das (1997) were applied to predict the micro-particle transport in a numerically simulated gas flow. Simulated pressure histories agree well with the corresponding static and Pitot pressure measurements, validating the CFD approach. The calculated velocity distributions show a good agreement, with the best prediction from Igra & Takayama correlation (maximum discrepancy of 5%). Key features of the gas dynamics and gas-particle interaction are discussed. Statistic analyses show a tight free-jet particle velocity distribution is achieved (570 +/- 14.7 m/s) for polystyrene particles (39 +/- 1 mu m), representative of a drug payload.

Effectiveness Of The Endotracheal Tube Cuff On The Trachea: Physical And Mechanical Aspects.

The inflation pressure of the endotracheal tube cuff can cause ischemia of the tracheal mucosa at high pressures; thus, it can cause important tracheal morbidity and tracheal microaspiration of the oropharyngeal secretion, or it can even cause pneumonia associated with mechanical ventilation if the pressure of the cuff is insufficient. In order to investigate the effectiveness of the RUSCH® 7.5 mm endotracheal tube cuff, this study was designed to investigate the physical and mechanical aspects of the cuff in contact with the trachea. For this end, we developed an in vitro experimental model to assess the flow of dye (methylene blue) by the inflated cuff on the wall of the artificial material. We also designed an in vivo study with 12 Large White pigs under endotracheal intubation. We instilled the same dye in the oral cavity of the animals, and we analyzed the presence or not of leakage in the trachea after the region of the cuff after their deaths (animal sacrifice). All cuffs were inflated at the pressure of 30 cmH2O. We observed the passage of fluids through the cuff in all in vitro and in vivo experimental models. We conclude that, as well as several other cuff models in the literature, the RUSCH® 7.5 mm tube cuffs are also not able to completely seal the trachea and thus prevent aspiration of oropharyngeal secretions. Other prevention measures should be taken.

Human fallopian tube: a new source of multipotent adult mesenchymal stem cells discarded in surgical procedures

Background: The possibility of using stem cells for regenerative medicine has opened a new field of investigation. The search for sources to obtain multipotent stem cells from discarded tissues or through non-invasive procedures is of great interest. It has been shown that mesenchymal stem cells (MSCs) obtained from umbilical cords, dental pulp and adipose tissue, which are all biological discards, are able to differentiate into muscle, fat, bone and cartilage cell lineages. The aim of this study was to isolate, expand, characterize and assess the differentiation potential of MSCs from human fallopian tubes (hFTs). Methods: Lineages of hFTs were expanded, had their karyotype analyzed, were characterized by flow cytometry and underwent in vitro adipogenic, chondrogenic, osteogenic, and myogenic differentiation. Results: Here we show for the first time that hFTs, which are discarded after some gynecological procedures, are a rich additional source of MSCs, which we designated as human tube MSCs (htMSCs). Conclusion: Human tube MSCs can be easily isolated, expanded in vitro, present a mesenchymal profile and are able to differentiate into muscle, fat, cartilage and bone in vitro.