Alphanumeric LCD infrared control via computer’s parallel port

The present work will explain a method to achieve a remote controlled (via IR LED) alphanumeric Liquid Crystal Display. In modern times, the remote access of different devices has become quite popular, therefore, the aim of this project is to provide a useful tool that will integrate common and easy to access devices. The system includes a C language based user interface, an assembly language code for the AT89C51ED2 microcontroller instructions and some digital electronic circuits needed for the driving and control of both the LCD and the infrared communication, as well as the PC with a parallel port. The interaction of all the devices provides a whole system that can be helpful in different applications, or it can be separated into each one of its different stages to take the best advantage as possible.

Flow rate sprinkler development for site-specific irrigation

Due to the rapid depletion of water resources, water must be used more efficiently in agriculture to maintain current levels of yield in irrigated areas. The efficiency of irrigation systems can be increased by adjusting the amount of water applied to specific conditions of soil and crop, which may vary in a field. Taking into account spatial and temporal variability, it is evident that an equipment capable of providing different irrigation levels is necessary to meet the water requirement of the soil. This work aims to develop and evaluate a flow rate sprinkler to be used in center pivots or linear moving irrigation systems, with potential for utilization in irrigation scheduling. A prototype was developed by duplicating its calibrations, and discharge coefficient adjustment was carried out in the laboratory. To predict the flow rate, a successful model that represented the operation of the flow rate sprinkler was established. The calibration of the flow rate sprinkler prototype showed satisfactory statistical and technical results. Automation of the prototype was achieved by driving a step motor using communication from the parallel port of a microcomputer, which was controlled by a software developed for this purpose. The results were satisfactory and technically feasible.

Sistema de aquisição de dados em tempo real

Neste trabalho propus-me realizar um Sistema de Aquisição de Dados em Tempo Real via Porta Paralela. Para atingir com sucesso este objectivo, foi realizado um levantamento bibliográfico sobre sistemas operativos de tempo real, salientando e exemplificando quais foram marcos mais importantes ao longo da sua evolução. Este levantamento permitiu perceber o porquê da proliferação destes sistemas face aos custos que envolvem, em função da sua aplicação, bem como as dificuldades, científicas e tecnológicas, que os investigadores foram tendo, e que foram ultrapassando com sucesso. Para que Linux se comporte como um sistema de tempo real, é necessário configura-lo e adicionar um patch, como por exemplo o RTAI ou ADEOS. Como existem vários tipos de soluções que permitem aplicar as características inerentes aos sistemas de tempo real ao Linux, foi realizado um estudo, acompanhado de exemplos, sobre o tipo de arquitecturas de kernel mais utilizadas para o fazer. Nos sistemas operativos de tempo real existem determinados serviços, funcionalidades e restrições que os distinguem dos sistemas operativos de uso comum. Tendo em conta o objectivo do trabalho, e apoiado em exemplos, fizemos um pequeno estudo onde descrevemos, entre outros, o funcionamento escalonador, e os conceitos de latência e tempo de resposta. Mostramos que há apenas dois tipos de sistemas de tempo real o ‘hard’ que tem restrições temporais rígidas e o ‘soft’ que engloba as restrições temporais firmes e suaves. As tarefas foram classificadas em função dos tipos de eventos que as despoletam, e evidenciando as suas principais características. O sistema de tempo real eleito para criar o sistema de aquisição de dados via porta paralela foi o RTAI/Linux. Para melhor percebermos o seu comportamento, estudamos os serviços e funções do RTAI. Foi dada especial atenção, aos serviços de comunicação entre tarefas e processos (memória partilhada e FIFOs), aos serviços de escalonamento (tipos de escalonadores e tarefas) e atendimento de interrupções (serviço de rotina de interrupção - ISR). O estudo destes serviços levou às opções tomadas quanto ao método de comunicação entre tarefas e serviços, bem como ao tipo de tarefa a utilizar (esporádica ou periódica). Como neste trabalho, o meio físico de comunicação entre o meio ambiente externo e o hardware utilizado é a porta paralela, também tivemos necessidade de perceber como funciona este interface. Nomeadamente os registos de configuração da porta paralela. Assim, foi possível configura-lo ao nível de hardware (BIOS) e software (módulo do kernel) atendendo aos objectivos do presente trabalho, e optimizando a utilização da porta paralela, nomeadamente, aumentando o número de bits disponíveis para a leitura de dados. No desenvolvimento da tarefa de hard real-time, foram tidas em atenção as várias considerações atrás referenciadas. Foi desenvolvida uma tarefa do tipo esporádica, pois era pretendido, ler dados pela porta paralela apenas quando houvesse necessidade (interrupção), ou seja, quando houvesse dados disponíveis para ler. Desenvolvemos também uma aplicação para permitir visualizar os dados recolhidos via porta paralela. A comunicação entre a tarefa e a aplicação é assegurada através de memória partilhada, pois garantindo a consistência de dados, a comunicação entre processos do Linux e as tarefas de tempo real (RTAI) que correm ao nível do kernel torna-se muito simples. Para puder avaliar o desempenho do sistema desenvolvido, foi criada uma tarefa de soft real-time cujos tempos de resposta foram comparados com os da tarefa de hard real-time. As respostas temporais obtidas através do analisador lógico em conjunto com gráficos elaborados a partir destes dados, mostram e comprovam, os benefícios do sistema de aquisição de dados em tempo real via porta paralela, usando uma tarefa de hard real-time.

Laboratori Assistit per Ordinador mitjançant eines ofimàtiques convencionals

El projecte "Laboratori Asssit per Ordinador Mitjançant Eines Ofimàtiques Convencionals" ha estat realitzat en la facultat de Física de la Universitat de Barcelona durant els anys 2007 i 2008 (projecte biennal). El principal objectiu d’aquest projecte és demostrar la possibilitat d’utilitzar les eines informàtiques més habituals en la realització d’experiències de laboratori assistit per ordinador (LAO). En particular, es proposa la utilització del Excel © juntament amb les seves macros (Visual Basic para Aplicacions, VBA) en pràctiques de laboratori d’assignatures en l’àrea de Física Aplicada. Excel és un full de càlcul molt conegut i usat tant per professors com pels estudiants. En aquest treball mostrem exemples concrets que abasten les diferents tècniques de control i adquisició de dades: programació del port sèrie (RS- 232) i paral·lel, i interfase GPIB. La implementació d’aquestes tècniques es realitza mitjançant macros VBA de Excel. La resta de programació de l’aplicació LAO, la representació gràfica i el tractament de les dades, es realitza de forma molt simple a partir del maneig habitual d’un full de càlcul. La realització del projecte ha demostrat la conveniència d’aquesta metodologia. Actualment pràcticament la totalitat de les pràctiques LAO de les quals és responsable el Departament de Física Aplicada utilitzen la programació a través del full de càlcul. La resposta dels estudiants ha estat molt positiva. La combinació de les característiques d’aquesta eina juntament amb la programació VBA té un enorme potencial i representa, probablement, una forma senzilla d’introduir tant a l’alumne com al professor en el món de la programació.

Manipulator control board

The Mechatronics Research Centre (MRC) owns a small scale robot manipulator called aMini-Mover 5. This robot arm is a microprocessor-controlled, six-jointed mechanical armdesigned to provide an unusual combination of dexterity and low cost.The Mini-Mover-5 is operated by a number of stepper motors and is controlled by a PCparallel port via a discrete logic board. The manipulator also has an impoverished array ofsensors.This project requires that a new control board and suitable software be designed to allow themanipulator to be controlled from a PC. The control board will also provide a mechanism forthe values measured using some sensors to be returned to the PC.On this project I will consider: stepper motor control requirements, sensor technologies,power requirements, USB protocols, USB hardware and software development and controlrequirements (e.g. sample rates).In this report we will have a look at robots history and background, as well as we willconcentrate how stepper motors and parallel port work

Uma interface lab-made para aquisição de sinais analógicos instrumentais via porta paralela do microcomputador

A lab-made interface for acquisition of instrumental analog signals between 0 and 5 V at a frequency up to 670 kHz at the parallel port of a microcomputer is described. Since it uses few and small components, it was built into the connector of a printer parallel cable. Its performance was evaluated by monitoring the signals of four different instruments and similar analytical curves were obtained with the interface and from readings from the instrument' displays. Because the components are cheap (~U$35,00) and easy to get, the proposed interface is a simple and economical alternative for data acquisition in small laboratories for routine work, research and teaching.

Autoamostrador de baixo custo para análise por injeção em fluxo

This paper describes a homemade autosampler for flow injection analysis (FIA), constructed with two step motors from old floppy disk drives (5¼-inch). The autosampler was connected to a computer through the parallel port and the sampling process was controlled by software in Quick Basic. The performance of the system was assessed by the determination of ammonium, based on the gaseous diffusion into a bromocresol purple solution, following the spectrophotometric determination of change in absorbance. The easy and simple construction is the main characteristics of this equipment and analytical results with RSD lower than 1% were obtained.

A VHDL-based protocol controller for NCAP processors

This work presents the development of an IEEE 1451.2 protocol controller based on a low-cost FPGA that is directly connected to the parallel port of a conventional personal computer. In this manner it is possible to implement a Network Capable Application Processor (NCAP) based on a personal computer, without parallel port modifications. This approach allows supporting the ten signal lines of the 10-wire IEEE 1451.2 Transducer Independent Interface (TII), that connects the network processor to the Smart Transducer Interface Module (STIM) also defined in the IEEE 1451.2 standard. The protocol controller is connected to the STIM through the TII's physical interface, enabling the portability of the application at the transducer and network processor level. The protocol controller architecture was fully developed in VHDL language and we have projected a special prototype configured in a general-purpose programmable logic device. We have implemented two versions of the protocol controller, which is based on IEEE 1451 standard, and we have obtained results using simulation and experimental tests. (c) 2008 Elsevier B.V. All rights reserved.

Manipulação remota de um braço mecânico (Scorbot ER - III) utilizando a rede mundial de computadores

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Implementação de um nó IEEE 1451, baseado em ferramentas abertas e padronizadas, para aplicações em ambientes de instrumentação distribuída

Pós-graduação em Engenharia Elétrica - FEIS

Second Welland Canal - Book 3, Survey Map 21 - Village of Port Colborne

Survey map of the Second Welland Canal created by the Welland Canal Company showing the areas in and around Port Colborne. Identified structures associated with the Canal include Lighthouse, Pier Light, Old Lock House, Collector's Office, Harbour Master's House, Canal Boundary, Back Ditch, Reserved Back Ditch, Basin, Light-Keeper's House and Ferry Recess. The surveyors' measurements and notes can be seen in red and black ink and pencil. Local area landmarks and businesses are also identified and include Gordon's Woodyard, Welland Rail Road, Welland Railway Elevator and Proposed Elevator, W.R.R. Flour Shed, Roman Catholic Church, School House, Sandhills, Lake Erie, and the High Water Mark. Streets running parallel to Canal include King St., West St., East St., Queen St., Hamilton St., and the Road Allowance are labelled. Streets running perpendicular to Canal include Kent St., Victoria St., Adelaide St., SugarLoaf St., George St., Alexandrina St., William St., Fort Erie St., Lake Rd., and New Road to Dutch Settlement are also labelled. Property owners and leasers as well as buildings on lots are also idenitified and noted as follows: Adams estate, J. Towhig, J.C. Kerr, Mrs. Hill, S. Cooke, Mrs. Yocum, W.T. Cooke, P. Wintermute, J. Shickluna, William Cooke, J. McChesney, John Beatty, W. Robertson, John Gordon, T. Armstrong, John Harper, George Keefer, Estate of James Black, Thomas Park, N. Higgins, S. Hopkins, and L.G. Cartier. Map of the Village of Port Colborne. Being Lot No. 27 and part of Lot No. 28 in the 1st Con. Township of HUMBERSTONE. Scale 2 Chs. per Inch. land shaded in RED Owned by DEPT. Do. Do. BLUE Sold to the COUNTY of WELLAND

Second Welland Canal - Book 3, Survey Map 20 - Village of Port Colborne

Survey map of the Second Welland Canal created by the Welland Canal Company showing the areas in and around Port Colborne and Grantham Township. Identified structures associated with the Canal include Basin, Guard Lock, Two Lock Tender Houses, Lock House Lot, Collectors Office House, Towing Path, North and South Back Ditches, and land reserved for future improvemnt of basin. Surveyor measurements and notes can be seen in red and black ink as well as pencil. Local area landmarks dentified include Bridge, Rail Road Swing Bridge, Spoil Bank, Water Tank, Frazer Street Railway Station, Buffalo and Lake Huron Rail Road, Welland Rail Road, and land reserved for "Gardens for Lock Tenders". Local businesses identified include A.K Scholfield Store House Lot and Wharf, two stores and a tavern. Roads running parallel to Canal include King St., "present Travel Road", and the Southern Road Allowance. Roads running perpendicular to Canal include Kent St., Charlotte St., Clarence St., Princess St., Elgin St., George St., Frazer St., Alma St., Eastern Road Allowance. Properties and property owners are also identified and include P. White, John Flynn, George McMicking, Charles Carter, William H. Merritt, A.K. Scholfield, F. Gallgher, Ed McCabe, M. Smith, E. Lawder, J. Hanley, J. Harris, P. Gibbons, M. McGoveran, M. Madden, J. Hardison, T. Nihan, D. Gibbons, J. Cross, William Mellanby, Elis Gordon, Jane McCardy, L.G. Carter, T. Greenwood, C. Armstrong, J. McGillivray, T. Schofield, Mrs. Lanue, D. Mc_______, K. Minor, J. Manly and John McRae.

Status of Early 19th-Century Names Authored in Parallel by Wied and Schinz for South American Reptiles and Amphibians, with Designations of Three Nomina Protecta

Prince Maximilian zu Wied's great exploration of coastal Brazil in 1815-1817 resulted in important collections of reptiles, amphibians, birds, and mammals, many of which were new species later described by Wied himself The bulk of his collection was purchased for the American Museum of Natural History in 1869, although many ""type specimens"" had disappeared earlier. Wied carefully identified his localities but did not designate type specimens or type localities, which are taxonomic concepts that were not yet established. Information and manuscript names on a fraction (17 species) of his Brazilian reptiles and amphibians were transmitted by Wied to Prof. Heinrich Rudolf Schinz at the University of Zurich. Schinz included these species (credited to their discoverer ""Princ. Max."") in the second volume of Das Thierreich ... (1822). Most are junior objective synonyms of names published by Wied. However, six of the 17 names used by Schinz predate Wied's own publications. Three were manuscript names never published by Wied because he determined the species to be previously known. (1) Lacerta vittata Schinz, 1822 (a nomen oblitum) = Lacerta striata sensu Wied (a misidentification, non Linnaeus nec sensu Merrem) = Kentropyx calcarata Spix, 1825, herein qualified as a nomen protectum. (2) Polychrus virescens Schinz, 1822 = Lacerta marmorata Linnaeus, 1758 (now Polychrus marmoratus). (3) Scincus cyanurus Schinz, 1822 (a nomen oblitum) = Gymnophthalmus quadrilineatus sensu Wied (a misidentification, non Linnaeus nec sensu Merrem) = Micrablepharus maximiliani (Reinhardt and Lutken, ""1861"" [1862]), herein qualified as a nomen protectum. Qualifying Scincus cyanurus Schinz, 1822, as a nomen oblitum also removes the problem of homonymy with the later-named Pacific skink Scincus cyanurus Lesson (= Emoia cyanura). The remaining three names used by Schinz are senior objective synonyms that take priority over Wied's names. (4) Bufo cinctus Schinz, 1822, is senior to Bufo cinctus Wied, 1823; both, however, are junior synonyms of Bufo crucifer Wied, 1821 = Chaunus crucifer (Wied). (5) Agama picta Schinz, 1822, is senior to Agama picta Wied, 1823, requiring a change of authorship for this poorly known species, to be known as Enyalius pictus (Schinz). (6) Lacerta cyanomelas Schinz, 1822, predates Teius cyanomelas Wied, 1824 (1822-1831) both nomina oblita. Wied's illustration and description shows cyanomelas as apparently conspecific with the recently described but already well-known Cnemidophorus nativo Rocha et al., 1997, which is the valid name because of its qualification herein as a nomen protectum. The preceding specific name cyanomelas (as corrected in an errata section) is misspelled several ways in different copies of Schinz's original description (""cyanom las,"" ""cyanomlas,"" and cyanom""). Loosening, separation, and final loss of the last three letters of movable type in the printing chase probably accounts for the variant misspellings.

IS ORDINARY ELECTRIC DRILLS` VENTING PORT A POTENTIAL SOURCE OF SURGICAL INFECTION?

Objective: To evaluate the potential risk of surgical contamination by the venting port of ordinary electric drills (ED) employed in orthopaedic surgeries. Materials and Methods: an experimental laboratory, randomized study was developed to analyze EDs in surgical practice and new cleaned and sterilized equipment, which were contaminated with Bacillus atrophaeus spores at a concentration of 84 X 10(6) UFC. The air generated by the engine of each drill was collected and cultivated on sterile agar plates. Results: Positive culture was identified in two ED in surgical practice, as well as a positive culture to Bacillus atrophaeus with 1 CFU growth (1, 19 X 10(-8)). Conclusion: In the conditions of the experiment, the air generated by the venting port of the ED`s engine does not consist of a source of contamination for the surgical site.

Harmonic identification using parallel neural networks in single-phase systems

In this paper, artificial neural networks are employed in a novel approach to identify harmonic components of single-phase nonlinear load currents, whose amplitude and phase angle are subject to unpredictable changes, even in steady-state. The first six harmonic current components are identified through the variation analysis of waveform characteristics. The effectiveness of this method is tested by applying it to the model of a single-phase active power filter, dedicated to the selective compensation of harmonic current drained by an AC controller. Simulation and experimental results are presented to validate the proposed approach. (C) 2010 Elsevier B. V. All rights reserved.