Investigation of the vapor-phase grafting of styrene onto PFA

Poly(tetrafluoroethylene-co-perfluoropropyI vinyl ether), PFA, was grafted with styrene from the vapor phase using a simultaneous radiation grafting method. The graft yields were measured as a function of the dose and dose rate and were found to be initially linearly dependent on the dose and independent of the dose rate up to dose rates of similar to3 kGy/h. However, at a dose rate of 6.2 kGy/h, the slope of the yield-grafting time plot decreased. Raman depth profiles of the grafts showed that the polystyrene concentrations were greatest near the surface of the grafted samples and decreased with depth. The maximum penetration depth of the graft depended on the radiation dose for a fixed dose rate. Fmoc-Rink loading tests showed that the grafts displayed superior loading compared to grafts prepared from bulk styrene or from styrene solutions other than methanol.

Cooperative effects in the detection of a nitroaliphatic liquid explosive and na explosive taggant in the vapor phase by calix[4]arene-based carbazole-containing conjugated polymers

Two fluorescent molecular receptor based conjugated polymers were used in the detection of a nitroaliphatic liquid explosive (nitromethane) and an explosive taggant (2,3-dimethyl-2,3-dinitrobutane) in the vapor phase. Results have shown that thin films of both polymers display remarkably high sensitivity and selectivity toward these analytes. Very fast, reproducible, and reversible responses were found. The unique behavior of these supramolecular host systems is ascribed to cooperativity effects developed between the calix[4] arene hosts and the phenylene ethynylene-carbazolylene main chains. The calix[4]-arene hosts create a plethora of host-guest binding sites along the polymer backbone, either in their bowl-shaped cavities or between the outer walls of the cavity, to direct guests to the area of the transduction centers (main chain) at which favorable photoinduced electron transfer to the guest molecules occurs and leads to the observed fluorescence quenching. The high tridimensional porous nature of the polymers imparted by the bis-calixarene moieties concomitantly allows fast diffusion of guest molecules into the polymer thin films.

Growth of semi-polar GaN on high index silicon (11h) substrates by metal organic vapor phase epitaxy

Magdeburg, Univ., Fak. für Naturwiss., Diss., 2014

Effect of humidity and solvent vapor phase on cellulose esters films

In the present study the effect of relative humidity (RH) during spin-coating process on the structural characteristics of cellulose acetate (CA), cellulose acetate phthalate (C-A-P), cellulose acetate butyrate (CAB) and carboxymethyl cellulose acetate butyrate (CMCAB) films was investigated by means of atomic force microscopy (AFM), ellipsometry and contact angle measurements. All polymer solutions were prepared in tetrahydrofuran (THF), which is a good solvent for all cellulose esters, and used for spin-coating at RH of (35 +/- A 5)%, (55 +/- A 5)% or (75 +/- A 5)%. The structural features were correlated with the molecular characteristics of each cellulose ester and with the balance between surface energies of water and THF and interface energy between water and THF. CA, CAB, CMCAB and C-A-P films spin-coated at RH of (55 +/- A 5)% were exposed to THF vapor during 3, 6, 9, 60 and 720 min. The structural changes on the cellulose esters films due to THF vapor exposition were monitored by means of AFM and ellipsometry. THF vapor enabled the mobility of cellulose esters chains, causing considerable changes in the film morphology. In the case of CA films, which are thermodynamically unstable, dewetting was observed after 6 min exposure to THF vapor. On the other hand, porous structures observed for C-A-P, CAB and CMCAB turned smooth and homogeneous after only 3 min exposure to THF vapor.

Vapor phase composition as an indicator of thermal stability of the Sm, Eu, and Yb chlorides

The Sm, Eu, and Yb tri- and dichlorides were investigated by Knudsen effusion mass spectrometry. It was found out by the analysis of mass spectra and ionization efficiency curves that the vapor composition is complex due to the partial high temperature decomposition/disproportionation of the samples. Up to five vapor species were identified for both LnCl3 (LnCl3, LnCl2, Ln2Cl4, Ln2Cl5, and Ln2Cl6) and LnCl2 (LnCl3, LnCl2, LnCl, Ln, and Ln2Cl4). The quantitative evaluation of vapor composition was made. It indicates that the disproportionation of SmCl2 and EuCl2 is negligible in the temperature range studied whereas that of YbCl2 and the decomposition of SmCl3 and YbCl3 cannot be neglected.

In situ study of Ge(100) surfaces with tertiarybutylphosphine supply in vapor phase epitaxy ambient

GaInP nucleation on Ge(100) often starts by annealing of the Ge(100) substrates under supply of phosphorus precursors. However, the influence on the Ge surface is not well understood. Here, we studied vicinal Ge(100) surfaces annealed under tertiarybutylphosphine (TBP) supply in MOVPE by in situ reflection anisotropy spectroscopy (RAS), X-ray photoelectron spectroscopy (XPS), and low energy electron diffraction (LEED). While XPS reveals a P termination and the presence of carbon on the Ge surface, LEED patterns indicate a disordered surface probably due to by-products of the TBP pyrolysis. However, the TBP annealed Ge(100) surface exhibits a characteristic RA spectrum, which is related to the P termination. RAS allows us to in situ control phosphorus desorption dependent on temperature.

Impact of metal-organic vapor phase epitaxy environment on silicon bulk lifetime for III–V-on-Si multijunction solar cells

With the final goal of integrating III-V materials on silicon substrates for tandem solar cells, the influence of the Metal-Organic Vapor Phase Epitaxy (MOVPE) environment on the minority carrier properties of silicon wafers has been evaluated. These properties will essentially determine the photovoltaic performance of the bottom cell in a III-V-on-Si tandem solar cell. A comparison of the base minority carrier lifetimes obtained for different thermal processes carried out in a MOVPE reactor on Czochralski silicon wafers has been carried out. An important degradation of minority carrier lifetime during the surface preparation (i.e. H2 anneal) has been observed. Three different mechanisms have been proposed for explaining this behavior: 1) the introduction of extrinsic impurities coming from the reactor; 2) the activation of intrinsic lifetime killing impurities coming from the wafer itself; and finally, 3) the formation of crystal defects, which eventually become recombination centers. The effect of the emitter formation by phosphorus diffusion has also been evaluated. In this sense, it has been reported that lifetime can be recovered during the emitter formation either by the effect of the P on extracting impurities, or by the role of the atomic hydrogen on passivating the defects.

Characterization of design and economic sensitivity of vapor phase carbon adsorption systems to environmental uncertainties

Vapor phase carbon adsorption systems are used to remove aromatics, aliphatics, and halogenated hydrocarbons. The adsorption capacity of granular activated carbon is reduced when environmental parameters (temperature, pressure, and humidity) interfere with homogeneous surface diffusion and pore distribution dynamics. The purpose of this study was to investigate the effects of parametric uncertainties in adsorption efficiency. ^ Modified versions of the Langmuir isotherm in conjunction with thermodynamic equations described gaseous adsorption of single component influent onto microporous media. Experimental test results derived from Wang et al. (1999) simulated adsorption kinetics while the Myer and monsoon Langmuir constant accounted for isothermal gas compression and energetic heterogeneity under thermodynamic equilibrium conditions. Responsiveness of adsorption capacity to environmental uncertainties was analyzed by statistical sensitivity and modeled by breakthrough curves. Results indicated that extensive fluctuations in adsorption capacity significantly reduced carbon consumption while isothermal variations had a pronounced effect on saturation capacity. ^

Corrosion resistant and adsorbent plasma polymerized thin film

Adsorbent and corrosion resistant films are useful for sensor development. Therefore, the aim of this work is the production and characterization of plasma polymerized fluorinated organic ether thin films for sensor development. The polymerized reactant was methyl nonafluoro(iso)butyl ether. Infrared Spectroscopy showed fluorinated species and eventually CO but CH(n) is a minor species. Contact angle measurements indicated that the film is hydrophobic and organophilic but oleophobic. Optical microscopy reveals not only a good adherence on metals and acrylic but also resistance for organic solvents, acid and basic aqueous solution exposure. Double layer and intermixing are possible and might lead to island formation. Quartz Crystal Microbalance showed that 2-propanol permeates the film but there is no sensitivity to n-hexane. The microreactor manufactured using a 73 cm long microchannel can retain approximately 9 X 10(-4) g/cm(2) of 2-propanol in vapor phase. Therefore, the film is a good candidate for preconcentration of volatile organic compounds even in corrosive environment. (C) 2009 Elsevier B.V. All rights reserved.

Contradiction of quantum mechanics with local hidden variables for quadrature phase amplitude measurements

We demonstrate a contradiction of quantum mechanics with local hidden variable theories for continuous quadrature phase amplitude (position and momentum) measurements. For any quantum state, this contradiction is lost for situations where the quadrature phase amplitude results are always macroscopically distinct. We show that for optical realizations of this experiment, where one uses homodyne detection techniques to perform the quadrature phase amplitude measurement, one has an amplification prior to detection, so that macroscopic fields are incident on photodiode detectors. The high efficiencies of such detectors may open a way for a loophole-free test of local hidden variable theories.

Do Low-shrink Composites Reduce Polymerization Shrinkage Effects?

Progress in polymer science has led to continuous reduction of polymerization shrinkage, exemplified by a new generation of ""low-shrink composites"". The common inference that shrinkage stress effects will be reduced in teeth restored with such restoratives with lower shrinkage was tested in extracted human premolars. Mesio-occluso-distal slot-shaped cavities were cut and restored with a conventional (SupremePlus) or low-shrink (RefleXions, Premise, Kalore, and LS) composite (N = 5). We digitized the coronal surfaces before and 10 min after restoration to determine cuspal deflection from the buccal and lingual volume change/area. We also determined the main properties involved (total shrinkage, post-gel shrinkage, degree of conversion, and elastic modulus), as well as microleakage, to verify adequate bonding. It was shown that, due to shrinkage stresses, buccal and lingual surfaces pulled inward after restoration (9-14 microns). Only Kalore and LS resulted in significantly lower tooth deformation (ANOVA/Student-Newman-Keuls post hoc, p = 0.05). The other two low-shrink composites, despite having the lowest and highest total shrinkage values, did not cause significant differences in cuspal deflection. Deflection seemed most related to the combination of post-gel shrinkage and elastic modulus. Therefore, even for significantly lower total shrinkage values, shrinkage stress is not necessarily reduced.

Towards cryogenic liquid –vapor energy storage units for space applications

Dissertation to obtain the Doctoral degree in Physics Engineering

Supramolecular polymers azo-containing : photo-responsive block copolymer elastomers and homopolymers

Beaucoup d'efforts dans le domaine des matériaux polymères sont déployés pour développer de nouveaux matériaux fonctionnels pour des applications spécifiques, souvent très sophistiquées, en employant des méthodes simplifiées de synthèse et de préparation. Cette thèse porte sur les polymères photosensibles – i.e. des matériaux fonctionnels qui répondent de diverses manières à la lumière – qui sont préparés à l'aide de la chimie supramoléculaire – i.e. une méthode de préparation qui repose sur l'auto-assemblage spontané de motifs moléculaires plus simples via des interactions non covalentes pour former le matériau final désiré. Deux types de matériaux photosensibles ont été ciblés, à savoir les élastomères thermoplastiques à base de copolymères à blocs (TPE) et les complexes d'homopolymères photosensibles. Les TPEs sont des matériaux bien connus, et même commercialisés, qui sont généralement composés d’un copolymère tribloc, avec un bloc central très flexible et des blocs terminaux rigides qui présentent une séparation de phase menant à des domaines durs isolés, composés des blocs terminaux rigides, dans une matrice molle formée du bloc central flexible, et ils ont l'avantage d'être recyclable. Pour la première fois, au meilleur de notre connaissance, nous avons préparé ces matériaux avec des propriétés photosensibles, basé sur la complexation supramoléculaire entre un copolymère tribloc simple parent et une petite molécule possédant une fonctionnalité photosensible via un groupe azobenzène. Plus précisément, il s’agit de la complexation ionique entre la forme quaternisée d'un copolymère à blocs, le poly(méthacrylate de diméthylaminoéthyle)-poly(acrylate de n-butyle)-poly(méthacrylate de diméthylaminoéthyle) (PDM-PnBA-PDM), synthétisé par polymérisation radicalaire par transfert d’atomes (ATRP), et l'orange de méthyle (MO), un composé azo disponible commercialement comportant un groupement SO3 -. Le PnBA possède une température de transition vitreuse en dessous de la température ambiante (-46 °C) et les blocs terminaux de PDM complexés avec le MO ont une température de transition vitreuse élevée (140-180 °C, en fonction de la masse molaire). Des tests simples d'élasticité montrent que les copolymères à blocs complexés avec des fractions massiques allant de 20 à 30% présentent un caractère élastomère. Des mesures d’AFM et de TEM (microscopie à force atomique et électronique à ii transmission) de films préparés à l’aide de la méthode de la tournette, montrent une corrélation entre le caractère élastomère et les morphologies où les blocs rigides forment une phase minoritaire dispersée (domaines sphériques ou cylindriques courts). Une phase dure continue (morphologie inversée) est observée pour une fraction massique en blocs rigides d'environ 37%, ce qui est beaucoup plus faible que celle observée pour les copolymères à blocs neutres, dû aux interactions ioniques. La réversibilité de la photoisomérisation a été démontrée pour ces matériaux, à la fois en solution et sous forme de film. La synthèse du copolymère à blocs PDM-PnBA-PDM a ensuite été optimisée en utilisant la technique d'échange d'halogène en ATRP, ainsi qu’en apportant d'autres modifications à la recette de polymérisation. Des produits monodisperses ont été obtenus à la fois pour la macroamorceur et le copolymère à blocs. À partir d'un seul copolymère à blocs parent, une série de copolymères à blocs partiellement/complètement quaternisés et complexés ont été préparés. Des tests préliminaires de traction sur les copolymères à blocs complexés avec le MO ont montré que leur élasticité est corrélée avec la fraction massique du bloc dur, qui peut être ajustée par le degré de quaternisation et de complexation. Finalement, une série de complexes d'homopolymères auto-assemblés à partir du PDM et de trois dérivés azobenzènes portant des groupes (OH, COOH et SO3) capables d'interactions directionnelles avec le groupement amino du PDM ont été préparés, où les dérivés azo sont associés avec le PDM, respectivement, via des interactions hydrogène, des liaisons ioniques combinées à une liaison hydrogène à travers un transfert de proton (acidebase), et des interactions purement ioniques. L'influence de la teneur en azo et du type de liaison sur la facilité d’inscription des réseaux de diffraction (SRG) a été étudiée. L’efficacité de diffraction des SRGs et la profondeur des réseaux inscrits à partir de films préparés à la méthode de la tournette montrent que la liaison ionique et une teneur élevée en azo conduit à une formation plus efficace des SRGs.

Enthalpy-driven ring-opening polymerization of highly strained macrocyclic biaryl-ether-ketones

Highly strained macrocyclic ether-ketones obtained by nickel-catalyzed cyclization of linear precursor oligomers undergo ring-opening polyinerization via ether exchange in the presence of nucleophilic initiators such as fluoride or phenoxide anions. Strain enthapies of these macrocycles, from DSC analyses of their exothermic ring-opening polymerization are in the range 50-90 kJ mol(-1). Melt-phase polymerization generally affords slightly cross-linked materials, but solution-phase polymerization at high macrocycle concentrations gives fully soluble, high molar mass polymers with inherent viscosities of up to 1.78 dL g(-1). Sequence-analysis of the resulting polymers by C-13 NMR shows that alternating or random monomer sequences may be obtained, depending on whether one or both aromatic rings adjacent to the ether linkages are activated toward nucleophilic attack.

Copolimeros de propileno-etileno com baixos teores de etileno : estrutura, morfologia e propriedades

A estrutura básica predomínante encontrada em todos os copolímeros foi a de longos blocos de polipropileno cristalizáveis, separados por unidades isoladas de etileno, que atuaram como defeitos cristalínos, reduzindo o grau de cristalínidade, além da perfeição e da espessura dos cristais. O gradual aumento do teor de etileno nas amostras origínais, até aproximadamente5 moI % provocou redução progressiva no comprimento dos blocos de propileno em ambas as frações cristalizável e elastomérica. Acima daquela concentração, o etileno mostrou por principal efeito a elevação do teor de borracha de etileno-propileno(EPR), refletíndo-seem pronunciado aumento da resistência ao impacto dos copolímeros, com pouca alteração do comprimento das seqüências propiJênicas nas frações cristaJizáveJe elastomérica. A estrutura e a morfologia da borracha EPR gerada foram analisadas, observando-se sua excepcional dispersão na fase contínua cristalína. Análise das curvas de fusão por DSC, utilizando-se conceitos cínéticos, demonstrou a existência de uma energia de ativação aparente de fusão, associada à introdução de unidades etilênicas nas cadeias, e relacionada ao processo de fusão dos cristais poliméricos. A redução de cristalínidade das amostras e o aumento de mobilidade de cadeia da fase amorfa para teores crescentes de etileno resultaram em redução da rigidez dos copolímeros. Propriedades ópticas, como "haze" e brilho mostraram-se dependentesdo balanço entre o teor de cristais e o teor de borracha. Um balanço global das propriedades analisadas sugere uma composição ótima para aplicações típicas de copolímeros de propileno-etileno aquela com teores de etileno entre 4 e 6 moI % (aproximadamente 3 -4 % em massa).