Secagem do resíduo industrial da acerola em leito de jorro: estudos fluidodinâmicos e análise do desempenho do secador

In this research, the drying process of acerola waste was investigated by using a spouted bed drier. The process was conducted using high density polyethylene inert particles with the objective of producing an ascorbic acid-rich final product. The fruit waste was ground and used to prepare different water-maltodextrin suspensions. Initially, fluidynamical experiments were conducted in order to evaluate the feeding effect on the spouted bed drier fluidynamics behavior. The experimental planning 23 + 3 was used to investigate the effect of the following variables: solids concentration, drying air temperature, intermittence time, production efficiency, solids retention and product losses by elutriation of fine particles on drier walls. The effect of selected independent variables on the drier stability was also evaluated based on a parameter defined as the ratio between the feed suspension volume and the total inert particles volume. Finally, the powder quality was verified in experiments with fixed feed flow and varying air drying temperature, drying air velocity and intermittence time. It was observed that the suspension interferes in the spouted bed drier fluidynamics behavior, and higher air flow is necessary to stabilize the drier. The suspension also promotes the expansion of the spouted bed diameter, decreases the solid circulation and favors the air distribution at the flush area. All variables interfere in the spouted bed performance, and the solids concentration has a major effect on the material retention and losses. The intermittence time also has great effect on the stability and material retention. When it comes to production efficiency, the main effect observed was the drying air temperature. First order models were well adjusted to retention and losses data. The acerola powder presented ascorbic acid levels around 600 to 700 mg/100g. Similar moisture and ascorbic acid levels were obtained for powders obtained by spouted bed and spray drier. However, the powder production efficiency of the spray drier was lower when compared to spouted bed drier. When it comes to energetic analysis, the spray drier process was superior. The results obtained for spouted bed drier are promising and highly dependent on the operational parameters chosen, but in general, it is inferred that this drying process is adequate for paste and suspension drying

Avaliação térmica e desempenho do processo de secagem de misturas de graviola e leite em secador de leito de jorro

The soursop (A. muricata) is a fruit rich in minerals especially the potassium content. The commercialization of soursop in natura and processed has increased greatly in recent years. Drying fruit pulp in order to obtain the powdered pulp has been studied, seeking alternatives to ensure the quality of dehydrated products at a low cost of production. The high concentration of sugars reducing present in fruits causes problems of agglomeration and retention during fruit pulp drying in spouted bed dryers. On the other hand in relation to drying of milk and fruit pulp with added milk in spouted bed, promising results are reported in the literature. Based on these results was studied in this work drying of the pulp soursop with added milk in spouted bed with inert particles. The tests were based on a 24 factorial design were evaluated for the effects of milk concentration (30 to 50% m/m), drying air temperature (70 to 90 °C), intermittency time (10 to 14 min), and ratio of air velocity in relation to the minimum spout (1.2 to 1.5) on the rate of production, of powder moisture, yield, rate of drying and thermal efficiency of the process. There were physical and chemical analysis of mixtures, of powders and of mixtures reconstituted by rehydration powders. Were adjusted statistical models of first order to data the rate of production, yield and thermal efficiency, that were statistically significant and predictive. An efficiency greater than 40% under the conditions of 50% milk mixture, at 70 ° C the drying air temperature and 1.5 for the ratio between the air velocity and the minimum spout has been reached. The intermittency time showed no significant effect on the analyzed variables. The final product had moisture in the range of 4.18% to 9.99% and water activity between 0.274 to 0.375. The mixtures reconstituted by rehydration powders maintained the same characteristics of natural blends.

Avaliação da aplicação de modelos para a secagem de pastas e suspensões em leito de jorro com alimentação contínua

This work studies the development, implementation and improvement of a macroscopic model to describe the behavior of the spouted bed dryer with continuous feeding for pastes and suspensions drying. This model is based on the CST model (Freire et al., 2009) and the model of Fernandes (2005), whose theoretical foundation is based on macroscopic mass and heat balances for the three phases involved in the process: gas, liquid and solid. Because this technique is quite relevant, the studies of modeling and simulation of spouted bed drying are essential in the analysis of the process as a whole, because through them it is possible to predict and understand the behavior of the process, which contributes significantly to more efficient project and operation. The development and understanding of the phenomena involved in the drying process can be obtained by comparing the experimental data with those from computer simulations. Such knowledge is critical for choosing properly the process conditions in order to obtain a good drying efficiency. Over the past few years, researches and development of works in the field of pastes and suspensions drying in spouted bed has been gaining ground in Brazil. The Particulate Systems Laboratory at Universidade Federal do Rio Grande do Norte, has been developing several researches and generating a huge collection of experimental data concerning the drying of fruit pulps, vegetables pastes, goat milk and suspensions of agro-industrial residues. From this collection, some data of goat milk and residue from acerola (Malpighia glabra L.) drying were collected. For the first time, these data were used for the development and validation of a model that can describe the behavior of spouted bed dryer. Thus, it was possible to model the dryer and to evaluate the influence of process variables (paste feeding, temperature and flow rate of the drying air) in the drying dynamics. We also performed water evaporation experiments in order to understand and to study the behavior of the dryer wall temperature and the evaporation rate. All these analysis will contribute to future works involving the implementation of control strategies in the pastes and suspensions drying. The results obtained in transient analysis were compared with experimental data indicating that this model well represents the process

Fluidodinâmica de sementes de brócolos em leito fluizado e leito de jorro

The spouted and fluidized bed technologies are usually employed in operations of drying, coating and granulation of particles by the chemical and pharmaceutical industries. The use of these techniques in agronomy is limited to the treatment of some species of seeds. In this work, the objective was to analyse the fluid-dynamics of fluidized and spouted beds when broccoli (Brassica oleracea L. var. Italica) seeds are used and also to verify the influence on seed germination after 60 min of seed exposition to spouting or fluidization, at room temperature. The fluid-dynamics was defined by the measurements of the bed pressure drop as a function of the air flow rate for different seeds loads. The experimental conditions were based on the physical properties of the seeds and were limited by the apparatus dimensions. The cone-cylindrical bed was constructed in plexyglass to permit flow visualization. The values of the parameters: maximum pressure drop, minimum spouting flow rate and pressure drop, and stable spout pressure drop were experimentally obtained from the fluid-dynamic analysis and were compared with the values calculated by empirical equations found in the literature. The same procedure was carried out with the fluidized bed and the important parameters for this regime were the air velocity and the bed pressure drop at minimum fluidization. The analysis of seed germination indicated that no damage was caused to the seeds by the spout or fluidization processes.

Análise experimental do comportamento fluidodinâmico e da secagem de sementes de linhaça (Linum usitatissimum L.) em leito de jorro

A linhaça é a semente da planta do linho (Linum usitatissimum L.), uma espécie polimorfa originária do linho, sendo considerada uma das 6 plantas atualmente reconhecidas pelo Instituto Nacional do Câncer dos Estados Unidos (US National Cancer Institute - NCI) por suas propriedades específicas no combate ao câncer. Parte desse reconhecimento deve-se a notável característica de ser a fonte mais rica de precursores de lignina (esteróide vegetal de ação análoga ao estrógeno de mamíferos) na dieta humana. A variedade utilizada neste trabalho foi a “Linseed” de cor marrom e o objetivo deste trabalho foi analisar a fluidodinâmica dessa partícula em leito de jorro, estabelecida pelas medidas de tomadas de queda de pressão no leito a partir das deflexões em relação às velocidades de ar crescente e decrescente, obtendo assim informações para a determinação de parâmetros correlacionados ao processo, como: velocidade de mínimo jorro, queda de pressão máxima, queda de pressão no jorro estável e queda de pressão no mínimo jorro. Estes valores foram comparados aos correspondentes valores obtidos por equações empíricas citadas na literatura. Foi também avaliado o comportamento da secagem da matéria prima, mediante um planejamento estatístico 2², tendo com as variáveis de entrada temperatura do gás (T_g) e o tempo de operação (t), para a quantificação das variáveis de resposta razão de umidade (Xr, adim.), germinação (G, %) e o índice de velocidade de germinação (IVG, t^-1) e analisadas estatisticamente pelo planejamento fatorial completo com três repetições no ponto central. A cinética de secagem das sementes de linhaça, previamente umidificadas, foi realizada nas temperaturas de 45, 55 e 65 °C, e dentre os três modelos propostos, o modelo de Midilli et al., foi que melhor descreveu aos dados experimentais. Para os parâmetros fluidodinâmicos observou-se que a correlação de Gorshtein e Mukhlenov (1965) apresentou os menores desvios para queda e pressão de mínimo jorro e jorro estável, Abdelrazek (1969) apresentou o menor desvio para a velocidade no mínimo jorro e Pallai e Németh (1969) descreveu adequadamente a queda de pressão máxima. Foi observado que a carga de sementes e a temperatura exerceram influência significativa nos parâmetros fluidodinâmicos em leito de jorro. Com base na análise do planejamento estatístico proposto pode-se concluir que os parâmetros de entrada temperatura do gás e tempo de operação exerceram influência significativa sobre todas as variáveis de resposta, sendo observada influência quadrática das variáveis de entrada ao se observar a significância da curvatura sobre os parâmetros: Razão de umidade, Germinação e Índice de Velocidade de Germinação, propondo-se modelos representativos destes parâmetros com a presença da curvatura, apresentando um coeficiente de determinação (R²) superior a 99 %.

Efeito da secagem em leito de jorro bidimensional sobre as propriedades físicas e tecnológicas do feijão preto (Phaseolus vulgaris, L.)

A secagem de feijão preto (Phaseolus vulgaris, L.) em leito de jorro bidimensional foi estudada num equipamento em escala piloto de 100cm de altura total, 10cm de largura e 40cm de comprimento. Um soprador centrífugo de 7cv foi utilizado para fornecer o ar responsável pela formação do jorro ao sistema e nenhum aquecimento adicional foi realizado, ficando a temperatura de operação em torno de 50ºC. Foi feito um estudo sobre a influência do tempo de secagem, da vazão de ar injetado no sistema e da carga de grãos em cada batelada sobre o tempo de cozimento, a capacidade de absorção, a densidade e o diâmetro da partícula. A taxa de secagem também foi estudada. Observou-se que em 6 horas a redução de umidade do grão é cerca de 60% e as condições operacionais estudadas não afetaram significativamente as propriedades físicas e tecnológicas do feijão.

Secagem do resíduo de acerola (Malphigia emarginata D.C.): estudo do processo e avaliação do impacto sobre o produto final

Brazil, one of the largest agricultural producers in the world, has managed in recent years to significantly improve its production. However, in response to this advance in the agro-industrial sector, the generation of agro-industrial residues has also increased. New technological alternatives have to be implemented in order to bring economic and rational use of this material and drying is one of the possible choices. Considering the great importance that bioactive compounds present for food science and technology, this research aims to evaluate the air-drying process of acerola residue in a tray convective drier under controlled temperature (60, 70 e 80ºC), air velocity (4.0, 5.0 e 6.0 m/s) and material width (0.5, 0.62 e 0.75 cm) by applying an experimental planning 23 + 3. Based on that, the impact on physical-chemical characteristics, color, bioactive compounds concentration and antioxidant activity of dried acerola waste was evaluated, having the in natura and freeze dried waste as control groups. Dried acerola residue presented natural pigments, mainly carotenoids (143.68 - 68.29 mg/g) and anthocyanins (290.92 - 90.11 mg/100 g), which explain the red and yellow instrumental color parameters observed. The acerola residue powder is also rich in phenolic compounds (3261.11 -2692.60 mgGAEeq/100g), proanthocyanidins (61.33-58.46 eq/100g), ascorbic acid (389.44 739.29 mg/100 g) and DPPH antioxidant activity (20.91 24.72 μg Trolox eq/g). Results show decreased concentration of phenolic compounds, anthocyanins, carotenoids, proanthocyanidins and ascorbic acid caused by the air-drying process. However, even after the observed drying losses, the acerola residue powder can be considered a high value food ingredient, considering the high bioactive compounds concentration found in the final product, as well as the colorimetric characterization and microbiological stability of the dried powder

Avaliacao de dados de secagem de suspensoes de polpas de frutas em leito de jorro com alimentacao intermitente

The objective of this work was the development and improvement of the mathematical models based on mass and heat balances, representing the drying transient process fruit pulp in spouted bed dryer with intermittent feeding. Mass and energy balance for drying, represented by a system of differential equations, were developed in Fortran language and adapted to the condition of intermittent feeding and mass accumulation. Were used the DASSL routine (Differential Algebraic System Solver) for solving the differential equation system and used a heuristic optimization algorithm in parameter estimation, the Particle Swarm algorithm. From the experimental data food drying, the differential models were used to determine the quantity of water and the drying air temperature at the exit of a spouted bed and accumulated mass of powder in the dryer. The models were validated using the experimental data of drying whose operating conditions, air temperature, flow rate and time intermittency, varied within the limits studied. In reviewing the results predicted, it was found that these models represent the experimental data of the kinetics of production and accumulation of powder and humidity and air temperature at the outlet of the dryer

Secagem de grãos de girassol em leito fixo e em leito de jorro

This work studies two methods for drying sunflower grains grown in the western region of Rio Grande do Norte, in the premises of the Instituto Federal de Educação, Ciência e Tecnologia do Rio Grande do Norte - IFRN - Campus Apodi. This initiative was made because of the harvested grain during the harvest, being stored in sheds without any control of temperature, humidity etc. Therewith, many physical, chemical and physiological characteristics are compromised and grains lose much quality for oil production as their germination power. Taking into account that most of the stored grain is used for replanting, the studied methods include drying of grains in a thin layer using an oven with air circulation (fixed bed) and drying in a spouted bed. It was studied the drying of grains in natura, i.e., newly harvested. The fixed bed drying was carried out at temperatures of 40, 50, 60 and 70°C. Experiments in spouted bed were performed based on an experimental design, 2² + 3, with three replications at the central point, where the independent variables were grains load (1500, 2000 and 2500 g) and the temperature of the inlet air (70, 80, and 90 °C), obtaining the drying and desorption equilibrium isotherms. Previously, the characteristic curves of the bed were obtained. Both in the fixed bed as in the spouted bed, drying and desorption curves were obtained by weighing the grains throughout the experiments and measurements of water activity, respectively. The grains drying in the spouted bed showed good results with significant reduction of processing time. The models of FICK and PAGE were fitted to the experimental data, models which will represent the drying of grains both in the fixed bed as in the spouted bed. The desorption curves showed no influence of the processing temperature in the hygroscopic characteristics of the grains. The models of GAB, OSWIN and LUIKOV could well represent the desorption isotherms

Jambolão (Syzygium cumini) desidratado por liofilização e secagem em leito de jorro: avaliação do impacto do processo de secagem e caracterização do potencial funcional do produto final

Tropical fruits have been extensively studied due to their functional potential attributed to the presence of natural bioactive compounds. The exotic fruit jambolan (Syzygium cumini) has been reported for its appreciable amount of phenolic compounds, especially anthocyanins and antioxidant capacity. Nevertheless, there are hardly any derived jambolan products in the Brazilian market. In addition to that, considerable volumes of fruit are lost due to their high perishability. Dried fruits have become an important fruit market segment due to its weight and volume reduction and decreased transportation and storage costs. Thus, this study evaluated the jambolan pulp submitted to spouted bed drying (JLJ) and lyophilization (JLI), besides assessing the drying impact on the final product. In order to achieve this, the process performance was calculated and compared, as well the physicochemical and bioactive characteristics (moisture, water activity (aw), solubility, hygroscopicity, density, color, structure through images obtained by scanning electron microscopy (SEM), concentration of bioactive (total phenolic compounds (TPC), anthocyanins, proanthocyanidins and ascorbic acid) and antioxidant activity. The results showed drying efficiency higher than 60% for both products and that JLJ group showed higher moisture and water activity when compared to the JLI group (p<0.05). The two types of drying were able to produce stable final product in the microbiological point of view, given that both showed aw < 0.6. The final products exhibited high solubility (73.7 to 81.6%) and low hygroscopicity (9.8 to 11.6%), desirable characteristics for dehydrated foods. Despite the losses caused by drying, the dried jambolan pulp by both methods showed high TPC (468.6 to 534.0 mg GAE/100g dm), anthocyanins (from 491.9 to 673.4 mg. eq. cyanidin-3-glicoside/100g dm), proanthocyanidins (66.9 to 76.6 mg QTE/g dm) and ascorbic acid (156.4 to 186.8 mg/100 g dm). Taken together, the results of this study reveal spouted dried and freeze dried jambolan pulp as bioactive-rich natural products with suitable physicochemical and functional characteristics to be used as food ingredients. The data also demonstrate the drying techniques as rational strategies for the exploitation of the exotic fruit jambolan

Estudo da secagem do feijão verde (Vigna unguiculata L. Walp) - análise experimental do processo combinado leito fixo/leito de jorro

Green bean is considered as one of most traditional Brazilian Northeast dishes. Green beans drying preliminary experiments show that combine processes, fixed-bed/spouted bed, resulted in dehydrated beans with uniform humidity and the recovery of the beans properties after their rehydration. From this assays was defined an initial humidity suited for the spouted bed process. A fixed-bed pre-drying process until a level of 40% humidity gave the best results. The spouted bed characteristic hydrodynamic curves were presented for different beans loads, where changes in the respective beans physical properties were evidenced during the fluidynamic assay, due simultaneous drying process. One 22 factorial experimental design was carried out with three repetition in the central point, considering as entry variables: drying air velocity and temperature. The response variables were the beans brakeage, water fraction evaporated during 20 and 50 minutes of drying and the humidity ratio. They are presented still the modeling of the drying of the green beans in fine layer in the drier of tray and the modeling of the shrinking of the beans of the drying processes fixed-bed and spouted bed

Secagem de misturas de polpa de frutas tropicais em leito de jorro

Drying of fruit pulps in spouted beds of inert particles has been indicated as a viable technique to produce fruit powders. Most of the processes employed to produce dried fruit pulps and juices, such as Foam Mat, encapsulation by co-crystallization and spray drying utilize adjuvant and additives (such as thickeners, coating materials, emulsifiers, acidulants, flavors and dyes), which is not always desirable. The fruit pulp composition exerts an important effect on the fruit powder production using a spouted bed. In the study by Medeiros (2001) it was concluded that lipids, starch and pectin contents play an important role on the process performance, enhancing the powder production; however, the drying of fruit pulps containing high content of reducing sugars (glucose and fructose) is practically unviable. This work has the objective of expanding the studies on drying of fruit pulps in spouted bed with aid of adjuvant (lipids, starch and pectin) aiming to enhance the dryer performance without jeopardizing the sensorial quality of the product. The optimum composition obtained by Medeiros (2001) was the basis for preparing the mixtures of pulps. The mixture formulations included pulps of mango (Mangifera indica), umbu (Spondias tuberosa) and red mombin (Spondia purpurea) with addition of cornstarch, pectin and lipids. Different products were used as lipids source: olive and Brazil nut oils, coconut milk, heavy milk, powder of palm fat and palm olein. First of all, experiments were conducted to define the best formulation of the fruit pulps mixture. This definition was based on the drying performance obtained for each mixture and on the sensorial characteristics of the dry powder. The mixture formulations were submitted to drying at fixed operating conditions of drying and atomizing air flow rate, load of inert particles, temperature and flow rate of the mixture. The best results were obtained with the compositions having powder of palm fat and palm olein in terms of the drying performance and sensorial analysis. Physical and physicochemical characteristics were determined for the dry powders obtained from the mixtures formulations. Solubility and reconstitution time as well as the properties of the product after reconstitution were also evaluated. According to these analyses, the powder from the mixtures formulations presented similar characteristics and compatible quality to those produced in other types of dryers. Considering that the palm olein is produced in Brazil and that it has been used in the food industry substituting the palm fat powder, further studies on drying performance were conducted with the composition that included the palm olein. A complete factorial design of experiments 23, with three repetitions at the central point was conducted to evaluate the effects of the air temperature, feeding flow rate and intermittence time on the responses related to the process performance (powder collection efficiency, material retained in the bed and angle of repose of the inert particles after the process) and to the product quality (mean moisture content, loss of vitamin C and solubility). Powder production was uniform for the majority of the experiments and the higher efficiency with lower retention in the bed (59.2% and 1.8g, respectively) were obtained for the air temperature of 80°C, mixture feed rate of 5ml/min in intervals of 10 min. The statistical analysis of the results showed that the process variables had individual or combined significant influences on the powder collection efficiency, material retention in the bed, powder moisture content and loss of vitamin C. At the experimental ranges of this work, the angle of repose and solubility were not influenced by the operating variables. From the results of the experimental design, statistical models were obtained for the powder moisture content and loss of vitamin C

Secagem de misturas de polpa de frutas tropicais em leito de jorro

Drying of fruit pulps in spouted beds of inert particles has been indicated as a viable technique to produce fruit powders. Most of the processes employed to produce dried fruit pulps and juices, such as Foam Mat, encapsulation by co-crystallization and spray drying utilize adjuvant and additives (such as thickeners, coating materials, emulsifiers, acidulants, flavors and dyes), which is not always desirable. The fruit pulp composition exerts an important effect on the fruit powder production using a spouted bed. In the study by Medeiros (2001) it was concluded that lipids, starch and pectin contents play an important role on the process performance, enhancing the powder production; however, the drying of fruit pulps containing high content of reducing sugars (glucose and fructose) is practically unviable. This work has the objective of expanding the studies on drying of fruit pulps in spouted bed with aid of adjuvant (lipids, starch and pectin) aiming to enhance the dryer performance without jeopardizing the sensorial quality of the product. The optimum composition obtained by Medeiros (2001) was the basis for preparing the mixtures of pulps. The mixture formulations included pulps of mango (Mangifera indica), umbu (Spondias tuberosa) and red mombin (Spondia purpurea) with addition of cornstarch, pectin and lipids. Different products were used as lipids source: olive and Brazil nut oils, coconut milk, heavy milk, powder of palm fat and palm olein. First of all, experiments were conducted to define the best formulation of the fruit pulps mixture. This definition was based on the drying performance obtained for each mixture and on the sensorial characteristics of the dry powder. The mixture formulations were submitted to drying at fixed operating conditions of drying and atomizing air flow rate, load of inert particles, temperature and flow rate of the mixture. The best results were obtained with the compositions having powder of palm fat and palm olein in terms of the drying performance and sensorial analysis. Physical and physicochemical characteristics were determined for the dry powders obtained from the mixtures formulations. Solubility and reconstitution time as well as the properties of the product after reconstitution were also evaluated. According to these analyses, the powder from the mixtures formulations presented similar characteristics and compatible quality to those produced in other types of dryers. Considering that the palm olein is produced in Brazil and that it has been used in the food industry substituting the palm fat powder, further studies on drying performance were conducted with the composition that included the palm olein. A complete factorial design of experiments 23, with three repetitions at the central point was conducted to evaluate the effects of the air temperature, feeding flow rate and intermittence time on the responses related to the process performance (powder collection efficiency, material retained in the bed and angle of repose of the inert particles after the process) and to the product quality (mean moisture content, loss of vitamin C and solubility). Powder production was uniform for the majority of the experiments and the higher efficiency with lower retention in the bed (59.2% and 1.8g, respectively) were obtained for the air temperature of 80°C, mixture feed rate of 5ml/min in intervals of 10 min. The statistical analysis of the results showed that the process variables had individual or combined significant influences on the powder collection efficiency, material retention in the bed, powder moisture content and loss of vitamin C. At the experimental ranges of this work, the angle of repose and solubility were not influenced by the operating variables. From the results of the experimental design, statistical models were obtained for the powder moisture content and loss of vitamin C

Estudo da secagem de polpa de coco verde em leito de jorro e viabilidade de sua utilização na indústria

Pós-graduação em Engenharia e Ciência de Alimentos - IBILCE

Estudo das características físico-químicas e funcionalidade de bagaços de frutas tropicais desidratados em leito de jorro

Fruits are rich sources of bioactive compounds, including phenolic compounds. Tropical fruit cultivation is an important productive segment in Brazilian Northeast. Its industrialization generates solid wastes as co-products, with potential environmental impact. Considering the recognized bioactive content of fruit and its derivatives, this research has the objective of investigating acerola (Malpighia glabra L.), cajá-umbu (Spondia ssp), jambolan (Syzygium cumini) and pitanga (Eugenia uniflora) dried wastes obtained by spouted bed drier. It was analyzed the physical-chemical composition, solubility and microphotographic aspect of these dried wastes. Besides this, it was also evaluated the bioactive content, antioxidant activity and inhibitory activity against aamylase and a-glycosidase enzymes of water and ethanol (70%, 80% e 100% v/v) extracts prepared from fruit dried wastes, as well as their possible correlations. The dried fruit wastes showed high phenolic (606.04 to 3074.6 mg GAE eq/100 g sample), anthocyanin (478.7 mg/100 g for jambolan) and ascorbic acid (2748.03 mg/100 g for acerola) contents, as well as high antioxidant DPPH activity (14.27 a 36.30 mg Trolox eq/g sample). The extracts exhibited moderate to high a-amylase inhibition (23.97% a 76.58%) and high α-glycosidase inhibition, which 99.32% peak was reached for ethanol 70% pitanga extracts. It was also observed great positive correlation between phenolic content and DPPH activity (0.97 for acerola), anthocyanin (0.95 for jambolan) and α- glycosidase inhibition (0.98 for acerola). The α-glycosidase inhibition also correlated well with the antioxidant activity for all fruit extracts. The results show that these dried fruit wastes are valuable material for further applications as functional ingredients