Dynamic Tests of a Three-Span Continuous I-Beam Highway Bridge, HR-43, 1959

This paper presents the results of the static and dynamic testing of a three-span continuous I-beam highway bridge. Live load stress frequency curves for selected points are shown, and the static and dynamic load distribution to the longitudinal composite beam members are given. The bridge has four traffic lanes with a roadway width of 48 ft. Six longitudinal continuous WF beams act compositely with the reinforced concrete slab to carry the live load. The beams have partial length cover plates at the piers. Previous research has indicated that beams with partial length cover plates have a very low fatigue strength. It was found in this research that the magnitude of the stresses due to actual highway loads were very much smaller than those computed from specification loading. Also, the larger stresses which were measured occurred a relatively small number of times. These data indicate that some requirements for reduced allowable stresses at the ends of cover plates are too conservative. The load distribution to the longitudinal beams was determined for static and moving loads and includes the effect of impact on the distribution. The effective composite section was found at various locations to evaluate the load distribution data. The composite action was in negative as well as positive moment regions. The load distribution data indicate that the lateral distribution of live load is consistent with the specifications, but that there is longitudinal distribution, and therefore the specifications are too conservative.

Seismic design of highway bridge foundations.

"June 1986."

Report on a proposed highway bridge across the Columbia River at Astoria, Oregon, for the Port of Astoria, Oregon, Pacific County, Washington Oregon State Highway Commission [and] Washington Toll Bridge Authority, March 1955

Plans and cost estimates, by Tudor Engineering Company.--Traffic and revenue estimates, by Coverdale & Colpitts.

Report upon a traffic investigation for a proposed highway bridge between Easton and Phillipsburg, located at the foot of Bushkill street, Easton, Pennsylvania, to the Delaware river joint toll bridge commission, Pennsylvania-New Jersey, October 1935.

Mimeographed.

Feasibility Study of Dynamic Overload and Ultimate Load Tests of Full-Scale Highway Bridges, HR-160, 1973

As a result of the construction of the Saylorville Dam and Reservoir on the Des Moines River, six highway bridges are scheduled for removal. Five of these are old high-truss single-lane bridges, each bridge having several simple spans. The other bridge is a fairly modern (1955) double 4-span continuous beam-and-slab composite highway bridge. The availability of these bridges affords an unusual opportunity for study of the behavior of full-scale bridges. Because of the magnitude of the potential testing program, a feasibility study was initiated and the results are presented in this two-part final report. Part I summarizes the findings and Part II presents the supporting detailed information.

Rock Island Centennial Bridge, Final Report on Construction of the Mississippi River Bridge Between Rock Island, Illinois and Davenport, Iowa, 1945

The Rock Island Centennial Bridge spanning the Mississippi River between Rock Island, Illinois and Davenport, Iowa was opened to traffic on July 12, 1940. It is a thoroughly modern, four-lane highway bridge, adequate in every respect for present day high speed passenger and transport traffic. The structure is ideally situated to provide rapid transit between the business districts of Rock Island and Davenport and serves not only the local or shuttle traffic in the Tri-City Area, but also heavy through motor travel on U.S. Highways 67 and 150. The Centennial Bridge is notable in several respects. The main spans are box girder rib tied arches, a type rather unusual in America and permitting simplicity in design with pleasing appearance. The Centennial Bridge is the only bridge across the Mississippi providing for four lanes of traffic with separation of traffic in each direction. It is a toll bridge operating alongside a free bridge and has the lowest rates of toll of any toll bridge on the Mississippi River. It was financed entirely by the City of Rock Island with no obligation on the taxpayers; there was no federal or state participation in the financing. But perhaps the most outstanding feature of the new bridge is its great need. A few remarks on the communities served by the new structure, the services rendered, and some statistics on cross-river traffic in the Tri-City Area will emphasize the reasons for constructing the Centennial Bridge.

A Continuous Span Aluminum Girder Concrete Deck Bridge - Part 2 of 2: Fatigue Tests of Aluminum Girders, Final Report, 1997

In 1957, the Iowa State Highway Commission, with financial assistance from the aluminum industry, constructed a 220-ft (67-m) long, four-span continuous, aluminum girder bridge to carry traffic on Clive Road (86th Street) over Interstate 80 near Des Moines, Iowa. The bridge had four, welded I-shape girders that were fabricated in pairs with welded diaphragms between an exterior and an interior girder. The interior diaphragms between the girder pairs were bolted to girder brackets. A composite, reinforced concrete deck served as the roadway surface. The bridge, which had performed successfully for about 35 years of service, was removed in the fall of 1993 to make way for an interchange at the same location. Prior to the bridge demolition, load tests were conducted to monitor girder and diaphragm bending strains and deflections in the northern end span. Fatigue testing of the aluminum girders that were removed from the end spans were conducted by applying constant-amplitude, cyclic loads. These tests established the fatigue strength of an existing, welded, flange-splice detail and added, welded, flange-cover plates and horizontal web plate attachment details. This part, Part 2, of the final report focuses on the fatigue tests of the aluminum girder sections that were removed from the bridge and on the analysis of the experimental data to establish the fatigue strength of full-size specimens. Seventeen fatigue fractures that were classified as Category E weld details developed in the seven girder test specimens. Linear regression analyses of the fatigue test results established both nominal and experimental stress-range versus load cycle relationships (SN curves) for the fatigue strength of fillet-welded connections. The nominal strength SN curve obtained by this research essentially matched the SN curve for Category E aluminum weldments given in the AASHTO LRFD specifications. All of the Category E fatigue fractures that developed in the girder test specimens satisfied the allowable SN relationship specified by the fatigue provisions of the Aluminum Association. The lower-bound strength line that was set at two standard deviations below the least squares regression line through the fatigue fracture data points related well with the Aluminum Association SN curve. The results from the experimental tests of this research have provided additional information regarding behavioral characteristics of full-size, aluminum members and have confirmed that aluminum has the strength properties needed for highway bridge girders.

Projecto de execução de fundações e estruturas de uma ponte em betão armado pré-esforçado

Este Trabalho refere-se ao Projecto de Execução de Fundações e Estruturas de uma Ponte Rodoviária em betão armado pré-esforçado, realizado no âmbito do Trabalho Final de Mestrado em Engenharia Civil – Especialização em Estruturas, do Instituto Superior de Engenharia de Lisboa. O Projecto de Execução é composto de Peças Escritas e Peças Desenhadas. Nas Peças Escritas estão incluídos: Memória Justificativa e Descritiva; Cálculos Justificativos e Anexos. A ponte é composta por dois tabuleiros paralelos com 10,28m de largura cada um e afastados entre si de 0,10m. A obra é constituída de 8 tramos; os tramos correntes com 31m de comprimento e os tramos extremos com 25 e 20m de comprimento, perfazendo um comprimento total de 231m. A obra foi parcialmente isolada dos sismos pela introdução, em todos os pilares, de aparelhos de apoio de elevado amortecimento sísmico do tipo HDRB (High Damping Rubber Bearings). Encontram-se particularmente discriminadas e detalhadas neste projecto as seguintes situações: - Cálculo do Pré-esforço e respectivas perdas; - Acção das sobrecargas rodoviárias; - Diferença de comportamento da obra na entrada em serviço e no longo prazo; - Análise sísmica e do isolamento sísmico; - Estudo dos efeitos diferidos: retracção e fluência. Tendo as abordagens de cálculo e as verificações de segurança seguido a regulamentação nacional em vigor, nomeadamente RSA e REBAP, foi no entanto feita uma aproximação às regras do “Capacity Design” previstas no EC8, em que se privilegia a actuação do projectista sobre o comportamento da estrutura, procurando uma resposta não linear da mesma, visando garantir que: - A rotura não ocorrerá nos elementos de fundação; - Nos pilares a dissipação de energia se faz através de rótulas plásticas, evitando-se roturas associadas a esforços transversos. A aplicação destas regras neste Projecto demonstrou haver um agravamento substancial na definição dos esforços a que devem resistir alguns dos componentes da estrutura, designadamente os pilares e as fundações, originando soluções de secções de betão e armaduras bem mais exigentes do que aqueles que resultariam da simples verificação de segurança, pela comparação entre esforços actuante e esforços resistentes “secção a secção”, imposta pela actual regulamentação nacional.

Projecto de execução de uma obra de arte

Trabalho de Projecto para obtenção do grau de Mestre em Engenharia na Área de Especialização em Estruturas

Sistemas e soluções pós-tensão na reabilitação de obras de arte

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Civil

Simplified design method for energy dissipating devices in retrofitting of seismically isolated bridges

Abstract: Highway bridges have great values in a country because in case of any natural disaster they may serve as lines to save people’s lives. Being vulnerable under significant seismic loads, different methods can be considered to design resistant highway bridges and rehabilitate the existing ones. In this study, base isolation has been considered as one efficient method in this regards which in some cases reduces significantly the seismic load effects on the structure. By reducing the ductility demand on the structure without a notable increase of strength, the structure is designed to remain elastic under seismic loads. The problem associated with the isolated bridges, especially with elastomeric bearings, can be their excessive displacements under service and seismic loads. This can defy the purpose of using elastomeric bearings for small to medium span typical bridges where expansion joints and clearances may result in significant increase of initial and maintenance cost. Thus, supplementing the structure with dampers with some stiffness can serve as a solution which in turn, however, may increase the structure base shear. The main objective of this thesis is to provide a simplified method for the evaluation of optimal parameters for dampers in isolated bridges. Firstly, performing a parametric study, some directions are given for the use of simple isolation devices such as elastomeric bearings to rehabilitate existing bridges with high importance. Parameters like geometry of the bridge, code provisions and the type of soil on which the structure is constructed have been introduced to a typical two span bridge. It is concluded that the stiffness of the substructure, soil type and special provisions in the code can determine the employment of base isolation for retrofitting of bridges. Secondly, based on the elastic response coefficient of isolated bridges, a simplified design method of dampers for seismically isolated regular highway bridges has been presented in this study. By setting objectives for reduction of displacement and base shear variation, the required stiffness and damping of a hysteretic damper can be determined. By modelling a typical two span bridge, numerical analyses have followed to verify the effectiveness of the method. The method has been used to identify equivalent linear parameters and subsequently, nonlinear parameters of hysteretic damper for various designated scenarios of displacement and base shear requirements. Comparison of the results of the nonlinear numerical model without damper and with damper has shown that the method is sufficiently accurate. Finally, an innovative and simple hysteretic steel damper was designed. Five specimens were fabricated from two steel grades and were tested accompanying a real scale elastomeric isolator in the structural laboratory of the Université de Sherbrooke. The test procedure was to characterize the specimens by cyclic displacement controlled tests and subsequently to test them by real-time dynamic substructuring (RTDS) method. The test results were then used to establish a numerical model of the system which went through nonlinear time history analyses under several earthquakes. The outcome of the experimental and numerical showed an acceptable conformity with the simplified method.

Performance en fluage des assemblages antiglissement avec des surfaces métallisées dans les ponts en acier

Les éléments des ponts en acier sont exposés à de sévères conditions environnementales, tel l’épandage de sels déglaçant sur les routes. Ces éléments ont besoin d’un niveau suffisant de protection contre la corrosion afin de préserver leur intégrité à long terme. Une solution efficace, devenue populaire au Canada, est la métallisation. La métallisation est un revêtement anticorrosion formé par projection thermique de métal, généralement du zinc, sur la surface à protéger. La protection fournie au substrat d’acier est assurée par une barrière physique et une protection galvanique. Pour le calcul des assemblages boulonnés antiglissement, les codes de conception, tel le code Canadien sur le calcul des ponts routiers CAN/CSA S6-14, spécifient, en fonction des conditions des surfaces de contact désirées, un coefficient de glissement à utiliser. Actuellement, ces codes ne fournissent aucun coefficient de glissement entre deux surfaces métallisées. Donc, il est pratique courante pour les fabricants de ponts en acier de masquer les surfaces de contact des joints boulonnés avant de métalliser, ce qui est très couteux pour l’industrie puisque ce travail doit se faire manuellement. Récemment, des études ont évalué la résistance au glissement à court terme d’assemblages antiglissement ayant des surfaces de contact métallisées. Les résultats ont révélé une résistance au glissement supérieure aux assemblages sur acier nu grenaillés. Dans la présente recherche, la performance en fluage des assemblages antiglissement métallisés a été caractérisée pour s’assurer qu’une résistance en glissement de Classe B soit toujours valide à long terme. L’effet de la relaxation de la force de serrage sur la charge de glissement a aussi été évalué. Les résultats ont démontré une bonne performance en fluage. Aussi, les résultats ont révélé que la relaxation de la force de serrage n’a pas d’impact significatif sur la résistance au glissement des assemblages antiglissement métallisés. Les conclusions de cette étude pourraient bien influencer de futures révisions des codes de conception et avoir un impact sur l’industrie de l’acier en Amérique du Nord.Mots clés : Assemblage boulonné antiglissement, métallisation, pont routier en acier, fluage, relaxation

Laboratory and Field Testing of an Accelerated Bridge Construction Demonstration Bridge: US Highway 6 Bridge over Keg Creek, RB02-012, 2013

The US Highway 6 Bridge over Keg Creek outside of Council Bluffs, Iowa is a demonstration bridge site chosen to put into practice newly-developed Accelerated Bridge Construction (ABC) concepts. One of these new concepts is the use of prefabricated high performance concrete (HPC) bridge elements that are connected, in place, utilizing advanced material closure-pours and quick-to-install connection details. The Keg Creek Bridge is the first bridge in the US to utilize moment-resisting ultra-high performance concrete (UHPC) joints in negative moment regions over piers. Through laboratory and live load field testing, performance of these transverse joints as well as global bridge behavior is quantified and examined. The effectiveness of the structural performance of the bridge is evaluated to provide guidance for future designs of similar bridges throughout the US.

Standard Specifications for Highway and Bridge Construction, 2012

When referenced, the 2012 edition of the Iowa Department of Transportation’s (Iowa DOT) Standard Specifications for Highway and Bridge Construction shall be used for contract work awarded by the Iowa DOT. They may also be incorporated by reference in other contract work on secondary, urban, local systems, or other contract work in which the Iowa DOT has an interest. As modified by the General Supplemental Specifications, these Standard Specifications represent the minimum requirements and may be modified by Supplemental Specifications, Developmental Specifications, and Special Provisions on specific contracts. These Standard Specifications have been written so the Contractor’s responsibilities are indicated by plain language using the Imperative Mood and Active Voice form. Sentences are of the form: Construct isolation joints at all points where driveways meet other walks, curbs, or fixtures in the surface. Ensure finished members are true to detailed dimensions and free from twists, bends, open joints, or other defects resulting from faulty fabrication or defective work. Personnel preparing the JMF shall be Iowa DOT certified in bituminous mix design. The Contracting Authority’s responsibilities are (with some exceptions) indicated by the use of the modal verb “will”. Sentences are of the form: The Engineer will obtain and test density samples for each lot according to Materials I.M. 204. Payment will be the contract unit price for Fabric Reinforcement per square yard (square meter). These standard specifications contain dual units of measure: the United States Standard measure (English units) and the International System of Units (SI or “metric” units). The English units are expressed first then followed by the metric units in parentheses. The measurements expressed in the two systems are not necessarily equal. In some cases the measurements in metric units is a “hard” conversion of the English measurement; i.e. the metric unit has been approximated with a rounded, rationalized metric measurement that is easy to work with and remember. The proposal form will identify whether the work was designed and shall be constructed in English or metric units.

Iowa’s Bridge and Highway Climate Change and Extreme Weather Vulnerability Assessment Pilot, HEPN-707, 2015

The Iowa Department of Transportation (DOT) is responsible for approximately 4,100 bridges and structures that are a part of the state’s primary highway system, which includes the Interstate, US, and Iowa highway routes. A pilot study was conducted for six bridges in two Iowa river basins—the Cedar River Basin and the South Skunk River Basin—to develop a methodology to evaluate their vulnerability to climate change and extreme weather. The six bridges had been either closed or severely stressed by record streamflow within the past seven years. An innovative methodology was developed to generate streamflow scenarios given climate change projections. The methodology selected appropriate rainfall projection data to feed into a streamflow model that generated continuous peak annual streamflow series for 1960 through 2100, which were used as input to PeakFQ to estimate return intervals for floods. The methodology evaluated the plausibility of rainfall projections and credibility of streamflow simulation while remaining consistent with U.S. Geological Survey (USGS) protocol for estimating the return interval for floods. The results were conveyed in an innovative graph that combined historical and scenario-based design metrics for use in bridge vulnerability analysis and engineering design. The pilot results determined the annual peak streamflow response to climate change likely will be basin-size dependent, four of the six pilot study bridges would be exposed to increased frequency of extreme streamflow and would have higher frequency of overtopping, the proposed design for replacing the Interstate 35 bridges over the South Skunk River south of Ames, Iowa is resilient to climate change, and some Iowa DOT bridge design policies could be reviewed to consider incorporating climate change information.