632 resultados para OpenOffice.org
Resumo:
The objective of this study was to quantify the effect of plonk on compressive behavior and mechanical attributes such as consistency, optimum moisture for compaction and maximum density of a Red-Yellow Latosol (Oxisol) to evaluate the effect of plonk and compaction state in splashed particles, from Lavras (MG) region. The plonk was obtained from an artisanal sugarcane brandy alembic. Undisturbed and disturbed soil samples were collected at 0 to 3 cm and 60 to 63 cm depths. Disturbed soil samples were used for soil characterization, determination of consistence limits and Normal Proctor essay after material incubation with plonk. Undisturbed soil samples were saturated with plonk or distilled water (control) during 48 hours for testing the compressibility and resistance to splash by using simulated rainfall. The plonk altered the consistence limits of studied layers. For the 0-3 cm layer, the plonk reduced the friable range, and for the 60-63 cm layer the effect was in the opposite direction. For both layers, the plonk increased Dmax and decreased Uoptimum. Regardless of the plonk treatment, both layers presented the same load support capacity. The compaction degree of samples influenced the splash erosion. The increase of the applied pressure over the samples resulted in increase of splash material quantity. At the 60-63 cm layer, the plonk treatment reduced the splash material quantity by increasing the applied pressure, mainly when the samples were at field capacity.
Resumo:
One of the main objectives of applying edible coatings on fruits surface is to create a protective film to reduce weight loss due to evaporation and transpiration and also to decrease the risk of fruit rot caused by environmental contamination, in order to improve the visual aspect. Therefore, it is possible to increase shelf life, and decrease post harvest losses. Persimmon is a much appreciated fruit, with high potential for export, but sensitive to handling and storage. This study aimed to evaluate the effect of applying the edible coating Megh Wax ECF-124 (18% of active composts, consisting of emulsion of carnauba wax, anionic surfactant, preservative and water) produced by Megh Industry and Commerce Ltda in three different concentrations (25, 50 and 100%) on post harvest quality of 'Fuyu' persimmon stored for 14 days. The attributes evaluated for quality were: firmness, pH, acidity, soluble solids, weight loss and color. The results showed that application of carnauba wax in different concentrations was effective on decreasing weight loss of persimmon cv. Fuyu and maintenance of color aspects. Treatment at lower concentration, 25%, showed lower rate of discharge, but high concentrations showed lower values of mass loss. Carnauba wax application showed a high potential for use on postharvest conservation, and can be applied together with other technologies, helping to maintain quality for export.
Resumo:
This article has the aim to expand the perspective of research in the field of morality. We present a proposal of morality study of outlaw teenagers according to Thinking Organizer Models Theory. Through the idea of complexity we search to understand the cognitive process in the elaboration of moral reasoning inside situations of conflict. With this perspective, we developed a research that aimed to identify which organizer models were applied by 20 outlaw male teenagers who abide by social punishment to solve the hypothetical moral conflicts. Through interviews we told them a situation of moral conflict that involved friendship relation, physical aggression and steal. We could identified several models which were joined in three categories. Such models reflected the diversity and regularity that are present inside the elaborated reasoning to solve the conflicts shown by us. We conclude that the diversity of organizer models identified shows the importance of the contents in the construction of moral reasoning.
Resumo:
A vast literature review on the insomnia epidemiology, the most common sleep disorder, using MEDLINE and LILACS last 30 years of data, was performed from January 2002 to November 2003. The key-words were: sleep initiation disorders, sleep maintenance disorders, early awakening disorder, insomnia, sleep disorders, insomnia prevalence, insomnia consequences. Several insomnia definition criteria and epidemiology researches methods, with data comparison difficulties, were noticed. In the future it will be necessary similar insomnia definition and epidemiology studies criteria.
Resumo:
The present investigation evaluated the effects of diazepam used to manage uncooperative behavior of child dental patients. Six participants received placebo or diazepam (0,3 mg/kg weight) before formal dental treatment at total 54 sessions that were all recorded in videotapes. The analysis of recorded child (crying, body and/or head movements, escape and avoidance) and dentist's behavior management procedures (distraction, explanation, positive reinforcement) indicates no differences by using a double-blind Wilcoxon design (p>0.05). It is suggested the necessity of methodological refinement in studies that combine psychological and pharmacological handling strategies.
Resumo:
The aim of this paper was to identify, according to gender, the indexes of Mental Health and the Psychosocial Risk Factors in workers at a state University. A sample of 400 was randomly selected, 253 female and 147 male. They were assessed by means of The Questionnaire SWS Survey (Self, Work and Social) (Ostermann & Gutiérrez, 1992), validated in Brazil by Guimarães and Macfadden (1999). Univariate, bivariate, multivariate statistics were assessed. Significant associations emerged from Mental Health and Gender, and Psychosocial Risk Factors and Gender. Women showed greater Psychosocial Risk Factors, Work and Social Stress, worst mental health than men (p < 0.05), which place them at greater risk for developing physical and/or mental illness.
Resumo:
The relationship between aggressiveness and peer acceptance-rejection were analyzed in 1281 elementary school children. Sociometric measure was based on three positive and three negative classmates choices. The aggressiveness scales gathered information about familiar, scholar and general situations. There were no statistically insignificant differences among the schools related to the sociometric and aggressiveness in familiar situation measures. The scales of the scholar and general aggressiveness formed two sub-groups, in which two schools showed less aggressiveness and the two other more aggressiveness. Scholar aggressiveness showed significant correlations with the sociometric status in all schools and the general aggressiveness in one of them, suggesting that the most social acceptance, the lesser the student's aggressiveness. As the correlations were low, extreme groups in acceptance-rejection conditions had been studied and the scales of scholar and general aggressiveness had differentiated these groups in only one school.
Resumo:
This study contemplates reports and reflections about gender and the interfaces with work, power and woman's political participation within the Bororo indigenous communities in Mato Grosso, Guarani/Kaiowá and Kadiwéu ones, in Mato Grosso do Sul. In the study with the Bororo community, the woman valorization occurred because she represents the guardian of the culture and of the traditional knowledge, and at the same time, she is an important speaker for the Bororo and the non indigenous society. In the case of Guarani/Kaiowá community, the most important facts are, on one side, the departure of the men and their wish to become city men, and on the other, the women who wish or need to keep the Guarani identity and live in the reserve. In the Kadiwéu community, the most important fact is the women political power and a role division between men and women, without the attribution of more value to one role or the other.
Resumo:
The copolymer poly (L-co-D,L lactic acid), PLDLA, has gained prominence in the field of temporary prostheses due to the fact that their time of degradation is quite compatible with the requirement in the case of osseous fracture. In this work the in vivo degradation of devices from copolymer, as a system of plates and screws, used in fixation of the tibia of rabbits was studied. The devices were implanted in 15 adult rabbits, albinos, New Zealand race, and they were used as control devices of alloys of titanium (Ti-6Al-4V/ V grade). The use of copolymers, synthesized in the laboratory, was tested in the repair of fracture in rabbits'tibias, being assessed in the following times: 2 weeks, 2 months and 3 months. Morphological analysis of tissue surrounding the plate and screw system, for 2 weeks of implantation, showed the presence of osteoblasts, indicating a pre bone formation. After 2 months there was new bone formation in the region in contact with the polymer. This bone growth occurred simultaneously with the process of PLDLA degradation, invading the region where there was polymer and after 3 months there was an intense degradation of the copolymer and hence greater tissue invasion compared to 2 months which characterized bone formation in a region where the polymer degraded. The in vivo degradation study of the devices for PLDLA by means of histological evaluations during the period of consolidation of the fracture showed the efficiency of plate and screw system, and it was possible to check formation of bone tissue at the implantation site, without the presence of inflammatory reaction
Resumo:
Dental materials that release fluoride have been shown to be effective in caries inhibition around restorations. Adhesive materials would also be effective in caries inhibition by sealing and protecting cavity margins from acidic demineralization. This in vitro study tested the hypothesis that composite restorations with a dentin adhesive system have a caries preventive effect similar to that of an adhesive material with fluoride - glass-ionomer cement - on root surfaces. Twenty roots from extracted sound third molars were embedded in polystyrene resin and ground flat. Standardized cavities were prepared in leveled root surfaces and randomly restored with (a) Chelon-Fil (Espe) or (b) Z100/SingleBond (3M). Baseline indentations were measured at 100, 200 and 300 mum from the occlusal margins of each restoration and the surface microhardness values were obtained using a Knoop diamond indenter. A 2.0 mm wide margin around the restorations was submitted to a pH-cycling model, at 37ºC. After that, surface microhardness was measured again, as it was before. The differences between baseline and final surface microhardness were considered for statistical analysis. The median values of differences were (a): -3.8; -0.3; -1.0; and (b): 3.3; 2.5; 1.7, for the distances of 100, 200 and 300 mum, respectively. The Kruskal-Wallis test did not show statistically significant difference between 100, 200 and 300 mum distances in each tested group. There was no difference between the studied materials at the distances of 200 and 300 mum. Chelon-Fil was statistically different from Z100/SingleBond, at 100 mum (p<0.05). Under the studied conditions, the glass-ionomer cement had a higher caries preventive effect than the composite/dentin adhesive restorations.
Resumo:
The aim of this study was to test fear, anxiety and control related to dental treatment. The subjects were 364 children with ages between 7 and 13 years. Three questionnaires with multiple choice questions were applied in groups of 10 children. The first instrument was the 15-item dental subscale from the Childrens Fear Survey Schedule9. The subjects rated their level of fear on a 5-point scale. The second survey instrument was the 20-item subscale from the State Trait Anxiety Inventory for Children16. This measure was used to capture how anxious the child was, in general. The third instrument was the Child Dental Control Assessment19. It contained 20 items to assess perceived control and 20 items to assess desired control. The results of the survey indicated that dental fear and anxiety were slightly higher for females when compared with male subjects (P < 0.05). Older children (11 to 13 years old) obtained higher fear scores than younger ones (7 to 9 years old). Concerning perceived control, the results indicate that younger children perceive more control than older ones. For desired control, the results indicate that younger children reported higher percentages than older ones. In this study, patients who had undergone anesthesia during treatment revealed higher fear scores when compared with those who had not. Dental fear etiology seems to be related to a procedure that may involve pain or lack of control.
Resumo:
This study examined the influence of three polymerization cycles (1: heat cure - long cycle; 2: heat cure - short cycle; and 3: microwave activation) on the linear dimensions of three denture base resins, immediately after deflasking, and 30 days after storage in distilled water at 37± 2ºC. The acrylic resins used were: Clássico, Lucitone 550 and Acron MC. The first two resins were submitted to all three polymerization cycles, and the Acron MC resin was cured by microwave activation only. The samples had three marks, and dimensions of 65 mm in length, 10 mm in width and 3 mm in thickness. Twenty-one test specimens were fabricated for each combination of resin and cure cycle, and they were submitted to three linear dimensional evaluations for two positions (A and B). The changes were evaluated using a microscope. The results indicated that all acrylic resins, regardless of the cure cycle, showed increased linear dimension after 30 days of storage in water. The composition of the acrylic resin affected the results more than the cure cycles, and the conventional acrylic resin (Lucitone 550 and Clássico) cured by microwave activation presented similar results when compared with the resin specific for microwave activation.
Resumo:
The aim of this study was to compare two methods of surface roughness analysis, perfilometry and spectrophotometry, applied to the surface of ionomeric materials (Chelon Fil, Vitremer and Dyract), submitted to different surface finishing treatments. For the perfilometric analysis, sixty specimens of each material were made and randomly separated into three experimental groups. The average surface roughness (Ra, mm) was measured on each specimen by a surface perfilometer (Mitutoyo Surftest 211). The spectrophotometric analysis consisted in quantifying the dye impregnated in the samples. The dyes used were 0.5% fuchsin and 0.5% erythrosin. Data were submitted to variance analysis (ANOVA) and t-Student test at a 0.05 significance level. There was no linear correlation between average roughness and superficial deposition of dye. Perfilometric analysis revealed that 12- and 30-bladed carbide burs caused the roughest surface of Chelon Fil, followed by Sof-Lex discs and mylar band. There were no significant differences between the specimens submitted to finishing and polishing with Sof-Lex discs and the control group (mylar band) for Vitremer, nevertheless, the highest Ra values were obtained when 12- and 30-bladed burs were used. For Dyract, there was no significant difference between the three treatments. The mean values of superficial deposition of dye for Chelon Fil, Vitremer and Dyract were: 1.7261, 1.4759, 1.3318, respectively. There were no significant differences between the restorative materials when different finishing and polishing systems were used.
Resumo:
The aim of this study was to determine the effectiveness and reliability of laser fluorescence measurements in relation to occlusal caries diagnosis. DIAGNOdent 2095 (Kavo, Biberach, Germany), which has been developed especially for caries diagnosis, was utilized. Five (5) teeth were examined in the pilot test; after that, ten (10) teeth were examined in order to calibrate both examiners. Data were obtained from 66 teeth (36 molars and 30 premolars), totalizing 144 sites identified through photographs of the occlusal surfaces. Reproducibility was evaluated in 10 teeth. The interexaminer Spearman correlation (r) was 0.89 and the intra-examiner, 0.93 and 0.97 (examiner A and B, respectively). Validation was carried out by histological examination (stereomicroscope). For the two examiners the sensitivity of the device was relatively high, varying from 0.81 to 1.00, while specificity varied according to which validation criterion was used (0.77 - 0.86: enamel lesion / 0.52 - 0.59: dentin lesion). It was concluded that DIAGNodent presented good capacity of identifying any alteration of the dental surface, nevertheless it presents the disadvantage of accomplishing many false-positive diagnosis when the validation criterion is dentin lesion.
Estudo comparativo dos métodos de estimativa da idade óssea de Greulich & Pyle e Tanner & Whitehouse
Resumo:
The purpose of this study was to verify whether the Greulich & Pyle (GP), Greulich & Pyle Visual (GPV) and Tanner & Whitehouse (TW) methods for estimating skeletal age could be applied in the Brazilian population, and which of these three methods could be considered more reliable when compared with the chronological age of the individuals. This study was based on one hundred and sixty volunteers (80 females and 80 males) with ages between 6 years and 10 months and 14 years and 9 months. The results showed that for the GP method, the correlations with chronological age were 0.95 for males and 0.97 for females. For the GPV method, the correlations were 0.96 and 0.97, respectively and for TW, 0.96 and 0.97. The results showed that the Greulich & Pyle, Greulich & Pyle Visual and Tanner & Whitehouse methods presented high correlation values when compared with the chronological age of the individuals. Corrective factors were established to make these methods applicable to the Brazilian population.