Model for subchannel friction factors and flow redistribution in wire-wrapped rod bundles

The fuel element of LMFBR consists of a bundle of rods wrapped with an helical wire as spacer, surrounded by an hexagonal duct. In the present work, a semi-empirical model is developed to calculate bundle average and subchannel based friction factors and flow redistribution. The obtained results were compared to experimental data and they were considered satisfactory for wide range of geometrical parameters.

Parameter optimization of AC rectangular wave outputs for aluminum cold wire GTAW

The objective of this work was to optimize the parameter setup for GTAW of aluminum using an AC rectangular wave output and continuous feeding. A series of welds was carried-out in an industrial joint, with variation of the negative and positive current amplitude, the negative and positive duration time, the travel speed and the feeding speed. Another series was carried out to investigate the isolate effect of the negative duration time and travel speed. Bead geometry aspects were assessed, such as reinforcement, penetration, incomplete fusion and joint wall bridging. The results showed that currents at both polarities are remarkably more significant than the respective duration times. It was also shown that there is a straight relationship between welding speed and feeding speed and this relationship must be followed for obtaining sound beads. A very short positive duration time is enough for arc stability achievement and when the negative duration time is longer than 5 ms its effect on geometry appears. The possibility of optimizing the parameter selection, despite the high inter-correlation amongst them, was demonstrate through a computer program. An approach to reduce the number of variables in this process is also presented.

The pulsed wire anemometer: review and further developments

The purpose of the present paper is to review work that has been done on the pulsed wire anemometer technique and also suggest further developments that could be made in its range of application. The aper discusses the three types of probes that have been used in pulsed wire anemometry: the crossed wire velocity probe, the parallel wire wall shear stress probe and the parallel wire velocity probe. The work shows that the crossed wire and the parallel wire techniques can be used to make velocity, turbulence and wall shear stress measurements in highly turbulent flows without any upper restriction on turbulence level. Comments are also made on the potential of a parallel wire probe for use in highly turbulent flows that would enable higher order velocity cross-product terms to be measured.

Static pressure and wall shear stress distributions in air flow in a seven wire-wrapped rod bundle

An experimental investigation is performed in a turbulent flow in a seven wire-wrapped rod bundle, mounted in an open air facility. Static pressure distributions are measured on central and peripheral rods. By using a Preston tube, the wall shear stress profiles are experimentally obtained along the perimeter of the rods. The geometric parameters of the test section are P/D=1.20 and H/D=15. The measuring section is located at L/D=40 from the air inlet. It is observed that the dimensionless static pressure and wall shear stress profiles are nearly independent of the Reynolds number and strongly dependent of the wire-spacer position, with abrupt variations of the parameters in the neighborhood of the wires.

Evolução da pesquisa epidemiológica em atividade física no Brasil: revisão sistemática

OBJETIVO: Descrever a evolução da pesquisa epidemiológica em atividade física no Brasil. MÉTODOS: Revisão sistemática da literatura, realizada em bases de dados eletrônicas (Medline/PubMed, Lilacs, Ovid, Science Direct, BioMed Central e High Wire), em periódicos nacionais não indexados, por busca específica por autores e contato com pesquisadores. A seleção dos artigos teve como critérios de inclusão: amostra representativa de alguma população definida; tamanho da amostra de pelo menos 500 indivíduos; coleta de dados realizada no Brasil; mensuração de atividade física e relato dos resultados com base nessa variável. RESULTADOS: Foram incluídos 42 estudos. O primeiro artigo foi publicado em 1990, observando-se tendência de aumento de publicações a partir de 2000. Foi detectada disparidade regional nas publicações, com concentração de estudos nas regiões Sudeste e Sul. A maioria dos estudos (93%) utilizou questionários como instrumentos de pesquisa, cujos conteúdos variaram, assim como as definições operacionais de sedentarismo, dificultando a comparação dos resultados. CONCLUSÕES: Embora a literatura em epidemiologia da atividade física venha crescendo quantitativamente no Brasil, limitações metodológicas dificultam a comparação entre os estudos, tornando a padronização de instrumentos e definições essenciais para o avanço científico da área.

Endovascular techniques for placement of long-term chemotherapy catheters

PURPOSE: To analyze the results from using endovascular techniques to place long-term chemotherapy catheters when advancing the catheter using the external jugular vein is difficult due to obstructions or kinking. METHODS: Between July 1997 and August 2000, 320 long-term chemotherapy catheters were placed, and in 220 cases the external jugular vein was used as the primary venous approach. In 18 of these patients, correct positioning was not achieved and several endovascular techniques were then utilized to overcome these obstacles, including manipulation of a J-wire with a moveable core, venography, and the exchange wire technique. RESULTS: In 94.5% of the patients with difficulties in obtaining the correct positioning, we were able to advance the long-term catheter to the desired position with the assistance of endovascular techniques. CONCLUSIONS: Venography and endovascular guidance techniques are useful for the placement of long-term catheters in the external jugular vein.

Doença aterosclerótica difusa desmascarada pela avaliação fisiológica invasiva da circulação coronária

Sabe-se que a aterosclerose coronária é um processo difuso, pouco visível à angiografia. Este artigo descreve um paciente com angina estável, três meses após infarto agudo do miocárdio (IAM), e uma lesão severa na artéria descendente anterior (ADA), evidenciada pela cinecoronariografia. A reserva de fluxo fracionada do miocárdio (FFR), obtida através de medidas pressóricas intracoronárias, foi 0,37 durante a hiperemia máxima, demonstrando claramente a existência de isquemia. Um stent foi implantado na ADA e, a despeito do excelente resultado angiográfico, a FFR pós-stent foi apenas 0,75, o limite mínimo abaixo do qual existe isquemia. Quando a corda guia pressórica (pressure wire - PW) foi lentamente recuada da porção distal da ADA para sua porção proximal, notou-se um aumento contínuo e gradativo na pressão intracoronária, o que indica claramente aterosclerose difusa e não estenose focal. Não se notava gradiente no local do stent. O paciente foi mantido em tratamento médico e permanece assintomático até o momento.

Contribuição a história natural do «Pararu» Scardafella squammata squammata(Lesson) (1)

The main wild doves of the region of Piracicaba (State of S. Paulo, Brazil) are Columba cayennensis sylvestris Vieillot, Oreopeleia montana montana (L.), Leptotila verreauxi decipiens Salvadori, Columbigallina talpacoti talpacoti. (Temminck) and Scardafella squammata squammata (Lesson). The last one is well known for the beauty of the coloration of its feathers and for the characteristic sounds produced when flying up. Of common occurrence around the local farms, that species can easily be recognized not only for the mentioned peculiarities as for the voice of the adults, which was translated into the Brazilian onomatopoeia by the expression "fogo-apagou". S. squammata's biology being not well known, the Author presents some notes on its nidification, behaviour of both sexes and of the young birds. The data were gotten in nature and with specimens kept in captivity, where the reproduction took place. In such a situation, the male dove used thin and small wooden shavings to build the nest, an artificial material unknown by him when in nature. This fact may be considered as another proof of the plasticity of the instinctive conduct of birds, not so marked as the one given by SCHIRCH (1931) concerning Synallaxis sp. (Furnariidae), which made use of wire pieces and also barbed wires in confectioning the nest. The copulation was sometimes verified, being preceded by the phenomena well known in other Columbidae species. The nest had its building ready just on the day in which the first egg was laid. As it generally happens amongst doves, the nest was not carefully made - a simple and shallow bowl (diameter = 10 cm), where two entirely white eggs were put.. .. ..(22,5-24,5 x 18,0-19,0 mm). The eclosion took place 14 days after the laying of the last egg. As soon as the young doves (at least the male one) can feed by themselves, they try to produce the characteristic species sounds. "Pararu", a common name oly applied to another species - Claravis godefrida (Temminck) - is reported, which is preferably used by people in this region to call the studied dove. No differences between the coloration of the fathers of the two sexes were observed. The female dove seemed to be a little thinner than the male. In addition, the slight differences between the sounds produced by the male and female are pointed out.

Ecology and natural history of Akodon lindberghi (Rodentia, Sigmodontinae) in southeastern Brazil

We studied the ecology and natural history of the globally threatened and poorly known Akodon lindberghi Hershkovitz, 1990 in Parque Nacional da Serra da Canastra (PNSC) and Juiz de Fora (JF), southeastern Brazil. From November 1998 to September 2001 a total of 131 individuals were captured in wire-cage live-traps and 52 by pitfalls traps. They were all marked and released at the site. The largest abundances were registered during the dry season, and most of the captures occurred in open habitats. The mean body mass of the two populations was significantly different (18.1 g at PNSC versus 13.1 g at JF; H = 46.2678, g.l.=2, p<0.001). In PNSC, individuals were reproductively active from August to February, and juveniles were present from May to August. The results suggest that the changes in vegetation structure caused by deforestation and intensive agricultural activities could increase the predation rate, affecting the mean body mass of the population.

Um chronographo de construção simples, permittindo registrar intervallos de tempo de 1 a 60 segundos

Descriptive memorial of a chronograph made from a common chronoscop (Eastman Timer). The chronoscop has been modified in order to permit to adjust distinct cog-wheels, everyone in its turn, to the axis of the seconds hand. Each of these cog-wheels holds a definite number of teeth accordingly with the time interval ones desire to record. A wheel with 20 teeth, for instance, is available for recording time in periods of each three seconds, another wheel with 6 teeth, will reckon time in intervals of 10 seconds and so on. These wheels may be interchanged most easily, which enables, with the same apparatus, to have at hand a time recorder for any time interval between one and sixty seconds. To register the time the apparatus is connected with a dry cell. A wire is attached to a binding post on the metal case of the apparatus, another wire being connected with an isolated binding post placed in front of the cog-wheel and fastened to a platinum point allowing open or shut the circuit, every time one of the cogs of the wheel comes into contact with this platinum point. A signal magnet is placed also in the circuit for writing the time intervals on the revolving drum.

Quince 'CPP': new dwarf rootstock for pear trees on organic and high density planting

In Brazil, pear production presents the same incipient situation over the last 15 years, due mostly to low production technology. In this context, this study aimed to evaluate the development, growth and production of the pear tree cultivars Cascatense, Tenra and Hosui grafted on 'CPP' quince rootstock, using 'FT' pear as interstem. This trial was carried out in Guarapuava, State of Paraná, Southern region of Brazil, by five productive cycles. The pear trees were planted in September of 2004, spaced at 1.0 x 4.0 m (2,500 trees ha-1), trained to the modified central leader, on a Four-wire trellis, with drip irrigation and cultivated under organic production system. The following variables were evaluated: sprouting, anthesis, yield, fruit weight, soluble solids content, titratable acidity, pulp firmness, canopy area per plant and per hectare and trunk diameter. The pear tree cv. Tenra was outstanding most of the years for fruit yield, and, consequently, showed the highest accumulated yield over the period (51.6 t ha-1), followed by the cultivars Cascatense (39.7 t ha-1) and Hosui (18.7 t ha-1). All pear cultivars presented suitable physical-chemical characteristics for commercial purposes, with minimal average soluble solids content of 11% at harvest. The maximum canopy area per hectare was attained for cv. Cascatense (3063.2 m²), that was considered insufficient for a high yield. These results suggest the needs for studies with higher density planting and other training systems, searching optimize canopy volume. One of the most limiting factors in the organic pear orchard was the incidence of pear dieback caused by Botriosphaeria dothidea, severe more often in pear trees cv. Hosui.

Metodologia para o crescimento de esferas monocristalinas de metais nobres

This paper describes in detail a technique employed to grow quasi-spherical single crystals of noble metals for electrochemical applications, using platinum as an example. The metal beads were formed by melting the extremity of a wire in an oxygen / butane flame. X-ray techniques were used to check the crystallization and to determine the orientation of the crystals. Treatment with a pure hydrogen flame followed by a cooling procedure in a hydrogen / argon atmosphere were used for conditioning the well-defined platinum single crystal surfaces. Finally, electrochemical characterization of the Pt(111), Pt(110) and Pt(100) surfaces was done in diluted sulfuric acid solution in the hydrogen adsorption / desorption potential region.

Titulações potenciométricas de cátions metálicos tendo como eletrodo indicador o sistema Cu/Cu(II)-EDTA

In potentiometric titrations of metal cations with EDTA the Hg/HgY2- system is usually used to detect the end point. However, the use of mercury has been discouraged in analytical procedures due to its toxicity. In this work the Cu/CuY2- system was used as indicator electrode for potentiometric titrations of some metal cations with EDTA. The solutions of Cu2+, Cd2+, Mn2+, Co2+ and Zn2+ were titrated with Na2EDTA solution in the presence of a small concentration of the CuY2- complex using a copper wire as indicator electrode. The potentiometric titrations with the Cu/CuY2- system showed good correlation when compared with an Hg/HgY2- system.

Montagem de uma prensa para fios de sódio metálico

Several organic chemistry labs in Brazil suffers from the absence of a safe method to extrude sodium wire, used to obtain anhydrous solvents such as THF or ethyl ether. This technical note presents the assembly instructions for a sodium wire press, similar to the one that has been used for the past four years in our laboratory without any maintenance.

Determination of Mn2+ ion by solution scanometry as a new, simple and inexpensive method

In this research, scanometry was used as a new, simple, fast and inexpensive method for a colorimetric determination of Mn2+ ion in water samples and thermocouple wire through the use of periodate reagent in an acidic medium. The results showed the oxidization of colorless Mn2+ ion by periodate and the formation of a purplish MnO4- ion. The system had a linear range of 1.0 to 70.0 µg mL-1 Mn2+ ion with a detection limit of 0.314 µg mL-1 and a relative standard deviation of 2.77% for G color value. This method has the capability to determine low levels of Mn2+ ion in thermocouple wire and water samples.