Espalhamento e secagem de filme de amido-glicerol-fibra preparado por "tape-casting"

O objetivo deste trabalho foi avaliar processos de espalhamento e secagem de filme de amido-glicerol-fibras de celulose, preparado por "tape-casting". O espalhamento da suspensão foi avaliado a 50, 150 e 250 cm min-1, seguido de secagem em estufa com circulação forçada de ar, a 40 ou 70ºC; avaliou-se também o espalhamento da suspensão a 150 cm min-1, seguido da secagem do filme sobre suporte de "tape-casting" a 22ºC e 60% de umidade relativa, com velocidades do ar de 4, 6 e 8 m s-1 no túnel de secagem. Ensaios reológicos mostraram que o espalhamento das suspensões a temperaturas inferiores a 50ºC apresentou módulo de elasticidade superior ao módulo viscoso, em todo o espectro de frequências de oscilação. As microscopias mostraram filmes secos a 40 e 70ºC sem defeitos de formação, e cujas propriedades mecânicas não diferiam. A velocidade de espalhamento e a do ar não modificam o tempo de secagem nem as propriedades dos filmes. O tempo de secagem pode ser reduzido para aproximadamente duas horas, o que é importante para a produção dos filmes em larga escala.

Caracterização físico-química de filmes comestíveis de amido adicionado de acerola (Malphigia emarginata D.C.)

Edibles films are an alternative to synthetic materials used for packing food products. Barbados cherry is rich in vitamin C and carotenoids. The aim of this study was to characterize and develop films by casting from cassava starch, lyophilized Barbados cherry pulp and glycerol. The films were characterized with respect to thickness, water vapor permeability (WVP), water solubility, vitamin C, carotene and mechanical properties. The interaction of pulp and glycerol reduced film thickness. An increase in pulp concentration up to 60% increased WVP but beyond this concentration reduced both WVP and solubility leading to an increased level of vitamin C and β carotene in the films.

Characterization and in vitro release of cyclosporine-A from poly(D,L-lactide-co-glycolide implants obtained by solvent/extraction evaporation

Cyclosporine-A-loaded PLGA implants were developed intended for ocular route. Implants were prepared using solvent extraction/evaporation technique followed by casting of the cake into rods in a heated surface. XRD patterns showed that cyclosporine-A was completely incorporated into PLGA. FTIR and DSC results indicated alterations on drug molecular conformation aiming to reach the most stable thermodynamic conformation at polymer/drug interface. Implants provided controlled/sustained in vitro release of the drug. During the first 7 weeks, the drug release was controlled by the diffusion of the cyclosporine-A; and between 7-23 week period, the drug diffusion and degradation of PLGA controlled the drug release.

Ultrafiltration membranes from waste polyethylene terephthalate and additives: synthesis and characterization

The synthesis and characterization of asymmetric ultrafiltration membranes from recycled polyethylene terephthalate (PET) and polyvinylpyrrolidone (PVP) is reported. PET is currently used in many applications, including the manufacture of bottles and tableware. Monomer extraction from waste PET is expensive, and this process has not yet been successfully demonstrated on a viable scale. Hence, any method to recycle or regenerate PET once it has been used is of significant importance from scientific and environmental research viewpoints. Such a process would be a green alternative due to reduced raw monomer consumption and the additional benefit of reduced manufacturing costs. The membranes described here were prepared by a phase-inversion process, which involved casting a solution containing PET, m-cresol as solvent, and polyethylene glycol (PEG) of different molecular weights as additives. The membranes were characterized in terms of pure water permeability (PWP), molecular weight cut-off (MWCO), and flux and membrane morphology. The results show that the addition of PEG with high molecular weights leads to membranes with higher PWP. The presence of additives affects surface roughness and membrane morphology.

Bionanocompósitos preparados por incorporação de nanocristais de celulose em polímeros biodegradáveis por meio de evaporação de solvente, automontagem ou eletrofiação

This review reports the preparation and characterization of bionanocomposites based on biodegradable polymers reinforced with cellulose nanocrystals (CNC) described in the literature. The outstanding potential of cellulose nanocrystals as reinforcement fillers of biodegradable polymers is presented with an emphasis on the solution casting process, which is an appropriate method to investigate the physico-chemical effects of the incorporation of CNC into the polymeric matrices. Besides solution casting, other small scale methods such as electrospinning and layer-by-layer are also covered.

PRELIMINARILY DEVELOPMENT OF A MOISTURE-ACTIVATED BIORESORBABLE POLYMERIC PLATFORM FOR DRUG DELIVERY

Bioresorbable polymeric films were prepared by solvent casting using a tyrosine-derived polycarbonate and metronidazole (MDZ) as the model drug at 2.5%, 5% and 10% (w/w). Drug loading did not affect the water uptake, drug release, polymer degradation or erosion profiles. All devices released approximately 85% (w/w) of the drug within a 1.5 h period. This may be attributed to the rapid water uptake of the polymer. An increase in the water uptake correlated with a linear rate increase of the polymer degradation (0.968 ≤ R2 ≤ 0.999). Moreover, MDZ presented a remarkable plasticizing effect for the polymer and drug loading exerted a significant impact on the mechanical properties of the obtained films. The results obtained can be used to further the development of novel biocompatible and biodegradable polymeric platforms for the delivery of metronidazole and other drugs in a broad range of pharmaceutical applications.

CARACTERIZAÇÃO E AVALIAÇÃO IN VITRO DE NANOCOMPÓSITOS DE POLI (L-ÁCIDO LÁTICO) E NANOTUBOS DE CARBONO DE PAREDES MÚLTIPLAS PURIFICADOS

Carbon nanotubes (CNT) have been studied for biomedical applications due to their unique properties. However, pristine CNT have structural features and impurities that can cause toxicity to biological systems. In this work, we describe a method to purify multiwalled carbon nanotubes (MWCNT) by chemical modification and subsequent attachment of hydroxyl and carboxyl groups to improve dispersion and to decrease toxic effects. Nanocomposites from poly (L-lactic acid) (PLLA) and nanotubes were produced by the solvent casting method and characterized and evaluated for cytocompatibility with Vero cells. The nanocomposite interactions with Vero cells demonstrated that the cells were able to adhere and sustain proliferation and showed favorable cytocompatibility. In vitro studies also revealed an increase in fibroblast cell viability in the nanocomposites, compared with neat PLLA.

INTERCROPPING CORN WITH A COMBINATION OF TREE SPECIES TO CONTROL WEEDS

ABSTRACT The combination of crop residues or crop extracts is often more advantageous in controlling weeds, than the application of each residue or extract singly. This suggests that in intercropping with maize, the combination of tree species can be more advantageous than species isolated in weed control. The objective of this study was to evaluate the effects of intercropping with a combination of leguminous on the weed growth and corn yield. A randomized-block design with split plots (cultivars in plots) and five replicates was established. The cultivars BR 205 and AG 1041 were subject to the following treatments: two weedings (A), intercropping with sabiá (B), gliricidia (C), gliricidia + sabiá (D) and no weeding (E). In the B and C, 30 viable seeds m-2 of the leguminous were sown. In the D, 15 seeds of each species were sown m-2. The legumes were sown by random casting during corn planting. The sequence of the best treatments in reducing the growth of weeds is A > B = C = D = E. The sequence of the best treatments when are considered the yields of baby corn, green corn and grain is A > B > C > D > E. The cultivars do not differ in regards to the reduction in weed growth. In terms of corn yield cultivar BR 205 is the best.

Calculation of viscoelastic properties of edible films: application of three models

The viscoelastic properties of edible films can provide information at the structural level of the biopolymers used. The objective of this work was to test three simple models of linear viscoelastic theory (Maxwell, Generalized Maxwell with two units in parallel, and Burgers) using the results of stress relaxation tests in edible films of myofibrillar proteins of Nile Tilapia. The films were elaborated according to a casting technique and pre-conditioned at 58% relative humidity and 22ºC for 4 days. The testing sample (15mm x 118mm) was submitted to tests of stress relaxation in an equipment of physical measurements, TA.XT2i. The deformation, imposed to the sample, was 1%, guaranteeing the permanency in the domain of the linear viscoelasticity. The models were fitted to experimental data (stress x time) by nonlinear regression. The Generalized Maxwell model with two units in parallel and the Burgers model represented the relaxation curves of stress satisfactorily. The viscoelastic properties varied in a way that they were less dependent on the thickness of the films.

Queratina de penas de frango: extração, caracterização e obtenção de filmes

Apresenta-se neste trabalho um processo brando de extração de queratina de penas de frango em solução aquosa contendo uréia, 2-mercaptoetanol e um surfactante (pH 9,0). Foram realizadas as determinações das massas molares, do perfil de aminoácidos e da estabilidade térmica da queratina extraída. Resultados preliminares relativos às propriedades mecânicas de filmes de queratina obtidos por casting também são apresentados. A extração proporcionou um rendimento de 94% em relação à queratina presente inicialmente nas penas secas. As massas molares dos compostos presentes na solução de queratina extraída foram determinadas por eletroforese e variaram entre 10 e 14.000 g mol-1. A termogravimetria da queratina extraída mostrou que o processo de extração não modificou a temperatura de degradação da queratina. Os filmes de queratina obtidos apresentaram propriedades que estão de acordo com dados da literatura.

Características físicas de filmes biodegradáveis produzidos a partir de amidos modificados de mandioca

Amidos de mandioca podem ser matérias-primas para a obtenção de filmes biodegradáveis, sendo que para a formação destes é necessária a elaboração de suspensões filmogênicas. Alguns processos de modificação do amido podem torná-lo miscível em água fria, e outros processos de modificação podem alterar as propriedades dos filmes, tornando-os mais fortes e flexíveis. O objetivo deste trabalho foi verificar as características físicas de filmes biodegradáveis elaborados com amidos modificados de mandioca pelo processo de casting (desidratação de uma solução filmogênica sobre placas de Petri). Os amidos modificados utilizados foram: cross linked; carboximetilamido (CMA) de baixa viscosidade e alta viscosidade e esterificado. A viscosidade é fator importante para a elaboração da suspensão filmogênica e foi avaliada utilizando-se o equipamento Rapid Visco Analyser (RVA). Os filmes elaborados foram comparados a um filme de PVC comercial com espessura de 0,0208 a 0,0217 mm. Os amidos foram caracterizados por avaliação da composição físico-química, granulometria, microscopia eletrônica e viscosidade (Rapid Visco Analyser). A análise por microscopia eletrônica dos filmes ressaltou as diferenças entre os diferentes amidos utilizados. O RVA mostrou que, com exceção do cross linked, todos os amidos modificados apresentaram certa solubilidade a frio, o que facilita o preparo das soluções filmogênicas, entretanto, todos os amidos modificados apresentaram redução acentuada da tendência à retrogradação, propriedade geralmente associada à formação de filmes. As espessuras dos filmes de amido variaram de 0,0551 a 0,1279 mm, cujas espessuras mínimas foram a dos filmes de amido cross linked. Os filmes mostraram-se transparentes, manuseáveis e bem homogêneos. Não houve interferência da espessura na permeabilidade ao vapor d'água, e os filmes com 5% de matéria-seca, independente do tipo de amido modificado, foram mais permeáveis que o PVC. Porém, quando se compara o filme biodegradável de amidos modificados com o filme comercial de PVC, ainda há muito que se trabalhar na formulação para melhorar várias propriedades deste tipo de embalagem, que tem amplo uso atualmente.

Phase transitions in biodegradable films based on blends of gelatin and poly (vinyl alcohol)

The aim of this work was to study the effect of the hydrolysis degree (HD) and the concentration (C PVA) of two types of poly (vinyl alcohol) (PVA) and the effect of the type and the concentration of plasticizers on the phase properties of biodegradable films based on blends of gelatin and PVA, using a response-surface methodology. The films were made by casting and the studied properties were their glass (Tg) and melting (Tm) transition temperatures, which were determined by diferential scanning calorimetry (DSC). For the data obtained on the first scan, the fitting of the linear model was statistically significant and predictive only for the second melting temperature. In this case, the most important effect on the second Tm of the first scan was due to the HD of the PVA. In relation to the second scan, the linear model could be fit to Tg data with only two statistically significant parameters. Both the PVA and plasticizer concentrations had an important effect on Tg. Concerning the second Tm of the second scan, the linear model was fit to data with two statistically significant parameters, namely the HD and the plasticizer concentration. But, the most important effect was provoked by the HD of the PVA.

Mechanical and water vapor permeability properties of biodegradables films based on methylcellulose, glucomannan, pectin and gelatin

Mimic biological structures such as the cell wall of plant tissues may be an alternative to obtain biodegradable films with improved mechanical and water vapor barrier properties. This study aims to evaluate the mechanical properties and water vapor permeability (WVP) of films produced by using the solvent-casting technique from blended methylcellulose, glucomannan, pectin and gelatin. First, films from polysaccharides at pH 4 were produced. The film with the best mechanical performance (tensile strength = 72.63 MPa; elongation = 9.85%) was obtained from methylcellulose-glucomannan-pectin at ratio 1:4:1, respectively. Then, gelatin was added to this polysaccharide blend and the pH was adjusted to 4, 5 and 6. Results showed significant improvement in WVP when films were made at pH 5 and at polysaccharides/gelatin ratio of 90/10 and 10/90, reaching 0.094 and 0.118 g.mm/h.m².kPa as values, respectively. Films with the best mechanical properties were obtained from the blend of polysaccharides, whereas WVP was improved from the blend of polysaccharides and gelatin at pH 5.

Effect of modified clays on the structure and functional properties of biofilms produced with zein

The purpose of this study was to evaluate changes in the structure and some functional properties of biofilms added with modified clays (Cloisite® 15A and Cloisite® 30B) prepared by the casting method. The analysis of the microstructure of the films, scanning electron microscopy (SEM), Optical microscopy (MO), and Infrared Spectroscopy (FTIR) indicated that the addition of clay in the films resulted in the formation of a heterogeneous microstructure, microcomposite or tactoid. Due to the formation of a microcomposite structure, functional properties of the films added with both clays such as opacity, solubility, and permeability to water vapor (PVA), were not better than those of the control film. Thus, it was concluded that although it is possible to produce a film added with modified clays using the casting method, it was not possible to obtain intercalation or exfoliation in a nanocomposite, which would result in improved functional properties.

Development and characterization of orally-disintegrating films for propolis delivery

This study aimed at evaluating the effect of different concentrations of hydrolyzed collagen (HC) on the properties of an orally disintegrating film containing propolis ethanol extract (PEE) as an active component. The films were evaluated in terms of total phenols, mechanical properties, solubility, contact angle, disintegration time, and microstructure. The films were prepared by casting with 2 g of protein mass (gelatin and HC), 30 g of sorbitol/100 g of protein mass, and 100 g of PEE/100 g of protein mass. HC was incorporated at concentrations of 0, 10, 20, and 30 g/100 g of protein mass. It was found that increased concentrations of HC reduced tensile strength and increased elongation; however, all films showed plastic behavior. An increase in solubility at 25 ºC, a reduction in the contact angle, and disintegration time were also observed. Thus, higher concentrations of collagen led to more hydrophilic and more soluble polymeric matrices that showed shorter dissolution time, favoring the use of these materials as carriers for active compounds to be delivered in the oral cavity.