Direct determination of calcium in milk by atomic absorption spectrometry using flow-injection analysis

A flow-injection system with sample and reagent addition by the synchronous merging zones approach for calcium determination in milk by flame AAS is proposed. Main parameters were optimized using a factorial design with central point. The optimum conditions were 2.5% (m/v) for La concentration, 8 mL min-1 for the carrier flow-rate, 20 cm for coiled reactor and 250 ìL for sample volume. Different sample preparation procedures were evaluated such as dilution in water or acid and microwave-assisted decomposition using concentrated or diluted acids. The optimized flow system was applied to determine Ca in eleven commercial milk samples and two standard reference materials diluted in water. Similar calcium levels were encountered comparing the results obtained by the proposed method (dilution in water) with those obtained using microwave-oven digestion. Results obtained in two standard reference materials were in agreement at 95% confidence level with those certified. Recoveries of spiked samples were in the 93% - 116% range. Relative standard deviation (n = 12) was < 5.4% and the sample throughput was 150 measurements per hour, corresponding to a consumption of 250 µL of sample and 6.25 mg La per determination.

Spectrophotometric determination of ofloxacin in pharmaceuticals and human urine

Three simple and sensitive spectrophotometric methods are described for the determination of ofloxacin (OFX) in pharmaceuticals and in spiked human urine. First and second methods are based on the measurement of absorbance of OFX in 0.1 M HCl at 293 nm (method A) and 0.1 M NaOH at 287 nm, respectively. The third method is based on the measurement of 2:1 complex formed between OFX and iron(III) in H2SO4 medium, the complex peaking at 420 nm (method C). The optimum conditions for all the three methods are optimized. Beer's law is obeyed over the ranges 0.63-12.5 using method A and method B, and 10-120 µg mL-1 using method C. The apparent molar absorptivity values are calculated to be 3.5 × 10(4), 2.76 × 10(4) and 2.51 × 10³ L mol-1cm-1 for method A, method B and method C, respectively. The Sandell sensitivity, limit of detection (LOD) and limit quantification (LOQ) values are also reported. All the methods were validated in accordance with current ICH guidelines. The developed methods were employed with high degree of precision and accuracy for the estimation of total drug content in commercial tablet formulations of DOX. The results obtained from human spiked urine are satisfactory and recovery values are in the range 95.5-106.6%.

Spectrophotometric determination of nevirapine using tetrathiocyanatocobalt(II) ion as a reagent

A simple and rapid spectrophotometric method for the determination of nevirapine is described. The method is based on the reaction of nevirapine with tetrathiocyanatocobalt(II) ion in buffer of pH 4 to form the corresponding complex. Beer's law is obeyed in the range of 0.2 - 2.0 µg mL-1 for nevirapine. The optical parameters such as molar absorptivity, Sandell's sensitivity, detection limit and quantitation limit were found to be 1.16× 10(4) Lmol-1cm-1, 2.09 X 10-3 µg cm-2, 0.073 µg mL-1 and 0.222 µg mL-1 respectively. The optimum reaction conditions and other analytical parameters were evaluated. The statistical evaluation of the method was examined by determining intra-day and inter-day precision. The proposed method has been successfully applied for the determination of nevirapine in pharmaceutical formulations.

Effect of temperature, wetness duration and cultivar on the development of anthracnose in guava fruits

The development of a large number of postharvest diseases is closely associated with fruit ripeness. Environmental conditions may affect both the pathogen development and the fruit ripening rate. The aim of this study was to determine the most favorable temperature and wetness duration to the development of anthracnose in guava fruits. Cultivars 'Kumagai' (white pulp) and 'Pedro Sato' (red pulp) were inoculated with a conidial suspension of Colletotrichum gloeosporioides and C. acutatum and incubated at constant temperature ranging from 10 to 35ºC and wetness duration of 6 and 24 hours. Disease severity and incidence were evaluated at every two days during 12 days. No infection occurred at 10 and 35ºC, regardless of the wetness duration. The optimum conditions for fruit infection were 26 and 27ºC for 'Kumagai' and 25 and 26ºC for 'Pedro Sato', adopting 24 hours of wetness. In general, the disease development in 'Kumagai' cultivar was more affected by the wetness period, compared to 'Pedro Sato'. Disease severity for 'Kumagai' fruits was maximal between 25 and 30ºC , depending on the Colletotrichum species. Regarding 'Pedro Sato', the mean diameter of lesions was greater in fruits stored at 20, 25 and 30ºC , compared to 'Kumagai' cultivar, depending on the wetness period and the species. The incubation period (between 6 and 7 days) and the latent period (between 8 and 10 days) were minimal at 30ºC. The data generated in this study will be useful either for the development of a disease warning system or for the increase in the shelf life of guavas in the postharvest.

Bleached kraft pulp production from Pinus tecunumanii (Eguiluz e Perry)

The use of 12-year-old Pinus tecunumanii (Eguiluz e Perry) grown in Colombia was evaluated for bleached kraft pulp production. Kraft pulps of kappa number 30 ± 1 were produced, and oxygen delignified and bleached to 90% ISO with ECF processes. The bleached pulps produced under optimum conditions were evaluated with regard to their strength properties. Pinus tecunumanii wood required low effective alkali charge to reach the desired kappa number and the unbleached pulp showed high oxygen delignification efficiency and bleachability when a OD(EO)DED sequence was used. The bleached pulps presented good physical-mechanical properties, which are comparable to those obtained with more traditional pines such as Pinus taeda and Pinus radiata. The results demonstrate that this tropical pine species is a suitable raw material for bleached kraft pulp production

Calibration of angles of nozzles and deposition of an axial-flow sprayer on dwarf cashew

The study aimed to determine an optimum angle for the nozzles axial-flow sprayers a deposition for better vertical distribution focused on cashew. In laboratory tests were conducted adjusting the angle of the nozzle axial-flow sprayers. The experimental design was randomized blocks in a 2x3 factorial with four replications. The treatment for this test were two settings (with and without the adjustment of the angles of the nozzles ) and tree application volumes 273, 699 and 954 L ha-¹.The study was conducted in an orchard of dwarf cashew, with eight years of age. It was concluded that the volumetric distribution profile showed better vertical distribution uniformity when the angles of the nozzles were regulated for the canopy, the adjustment of the angles of the nozzles for the canopy provided greater deposition of droplets, the increased volume of application resulted in higher depositions in the leaves of the crop.

Estimated production and evapotranspiration of irrigated bean cultivars

The current study intended to determine the optimum water depth, yield and evapotranspiration (ETc) for bean cultivars. The experiment was conducted in the Campus of Unit I of the Triângulo Mineiro Federal Education and Technology Institute in Uberaba, MG, in a completely randomized design with three replications. The treatments consisted of four water-replacing levels in the soil (70, 100, 130 and 160% of the crop evapotranspiration) and four bean cultivars (Pérola, BRSMG Madrepérola, BRSMG Majestoso and IAC Alvorada). The average values of ETc obtained for soil water balance for the cultivars Pérola, BRSMG Madrepérola, BRSMG Majestoso and IAC Alvorada were, respectively, of 5.25 mm day-1, 4.59 mm day-1, 4.54 mm day-1 and 4.77 mm day-1. The water depths which provided the highest yields were for the cultivars Pérola, BRSMG Madrepérola, BRSMG Majestoso and IAC Alvorada of 451.61 mm, 454.41 mm, 504.71 mm and 344.30 mm, respectively. The maximum yields found were 4597.87 kg ha-1 (Pérola), 4546.27 kg ha-1 (BRSMG Madrepérola), 4253.39 kg ha-1 (BRSMG Majestoso) and 3958.50kg ha-1 (IAC Alvorada).

Management zones using fuzzy clustering based on spatial-temporal variability of soil and corn yield

Clustering soil and crop data can be used as a basis for the definition of management zones because the data are grouped into clusters based on the similar interaction of these variables. Therefore, the objective of this study was to identify management zones using fuzzy c-means clustering analysis based on the spatial and temporal variability of soil attributes and corn yield. The study site (18 by 250-m in size) was located in Jaboticabal, São Paulo/Brazil. Corn yield was measured in one hundred 4.5 by 10-m cells along four parallel transects (25 observations per transect) over five growing seasons between 2001 and 2010. Soil chemical and physical attributes were measured. SAS procedure MIXED was used to identify which variable(s) most influenced the spatial variability of corn yield over the five study years. Basis saturation (BS) was the variable that better related to corn yield, thus, semivariograms models were fitted for BS and corn yield and then, data values were krigged. Management Zone Analyst software was used to carry out the fuzzy c-means clustering algorithm. The optimum number of management zones can change over time, as well as the degree of agreement between the BS and corn yield management zone maps. Thus, it is very important take into account the temporal variability of crop yield and soil attributes to delineate management zones accurately.

Evaluation of the indirect fluorescent antibody test and modified agglutination test for detection of antibodies against Toxoplasma gondii in experimentally infected pigs

The study determined the sensitivity and specificity of the indirect fluorescent antibody test (IFAT) and modified agglutination test (MAT) for anti-Toxoplasma gondii antibody detection by analyzing sera from 46 experimentally infected pigs. Values for sensitivity were 95.7% (confidence interval 95%: 84.0-99.2%) and for specificity 97.8% (confidence interval 95%: 87.0-99.9%) in both tests. There was an optimum agreement of results between IFAT and MAT evidenced by a Kappa test of 0.86. These results validate these tests for the detection of T. gondii infection in pigs. IFAT and MAT despite methodologies with different characteristics and readings have similar accuracy in pig serum samples.

Venous hemogasometry of equines finalists in 90 km endurance races

Front of exercise, the organic systems may suffer water-electrolyte and acid-base imbalances, particularly in the case of blood gases, demonstrating variations from different causes, whether respiratory and/or metabolic. Understanding the physiological adaptations to exercise is essential in the search for the optimum performance. In this way, this study measured the venous blood gases (pO2, pCO2), as well as the oxygen saturation (SatO2) in healthy equines, Arabian horses finalists in 90km endurance races. A total of fourteen Arabian horses were evaluated, nine males and five females, between six and 12 years old, finalists in 90km endurance races. There was a significant reduction in pO2, pCO2 and SatO2 after the exercise, however, the values remained within the normality range, and did not change the athletic performance of the animals, indicating a temporary alteration, assuming thus a character of physiological response to the exercise performed. The equines, finalists in 90 Km endurance races, demonstrated efficient ventilatory process, without any alterations in the athletic performance, being adapted to the type of exercise imposed.

An experimental investigation of the effects of nozzle ellipticity on the flow structure of co-flow jet diffusion flames

The flow structure of cold and ignited jets issuing into a co-flowing air stream was experimentally studied using a laser Doppler velocimeter. Methane was employed as the jet fluid discharging from circular and elliptic nozzles with aspect ratios varying from 1.29 to 1.60. The diameter of the circular nozzle was 4.6 mm and the elliptic nozzles had approximately the same exit area as that of the circular nozzle. These non-circular nozzles were employed in order to increase the stability of attached jet diffusion flames. The time-averaged velocity and r.m.s. value of the velocity fluctuation in the streamwise and transverse directions were measured over the range of co-flowing stream velocities corresponding to different modes of flame blowout that are identified as either lifted or attached flames. On the basis of these measurements, attempts were made to explain the existence of an apparent optimum aspect ratio for the blowout of attached flames observed at higher values of co-flowing stream velocities. The insensitivity of the blowout limits of lifted flames to nozzle geometry observed in our previous work at low co-flowing stream velocities was also explained. Measurements of the fuel concentration at the jet centerline indicated that the mixing process was enhanced with the 1.38 aspect ratio jet compared with the 1.60 aspect ratio jet. On the basis of the obtained experimental data, it was suggested that the higher blowout limits of attached flames for an elliptic jet of 1.38 aspect ratio was due to higher entrainment rates.

Pressure Drop in Vertical Core-Annular Flow

An experimental apparatus for the study of core annular flows of heavy oil and water at room temperature has been set up and tested at laboratory scale. The test section consists of a 2.75 cm ID galvanized steel pipe. Tap water and a heavy oil (17.6 Pa.s; 963 kg/m³) were used. Pressure drop in a vertical upward test section was accurately measured for oil flow rates in the range 0.297 - 1.045 l/s and water flow rates ranging from 0.063 to 0.315 l/s. The oil-water input ratio was in the range 1-14. The measured pressure drop comprises gravitational and frictional parts. The gravitational pressure drop was expressed in terms of the volumetric fraction of the core, which was determined from a correlation developed by Bannwart (1998b). The existence of an optimum water-oil input ratio for each oil flow rate was observed in the range 0.07 - 0.5. The frictional pressure drop was modeled to account for both hydrodynamic and net buoyancy effects on the core. The model was adjusted to fit our data and shows excellent agreement with data from another source (Bai, 1995).

Optimal design of 3R manipulators by using classical techniques and simulated annealin

In this paper, the optimum design of 3R manipulators is formulated and solved by using an algebraic formulation of workspace boundary. A manipulator design can be approached as a problem of optimization, in which the objective functions are the size of the manipulator and workspace volume; and the constrains can be given as a prescribed workspace volume. The numerical solution of the optimization problem is investigated by using two different numerical techniques, namely, sequential quadratic programming and simulated annealing. Numerical examples illustrate a design procedure and show the efficiency of the proposed algorithms.

Influence of environmental factors on seed germination and seedling emergence of yellow sweet clover (Melilotus officinalis)

Laboratory and greenhouse experiments were conducted to determine the effects of drought and salinity stress, temperature, pH and planting depth on yellow sweet clover (Melilotus officinalis) germination and emergence. Base, optimum and ceiling germination temperatures were estimated as 0, 18.47 and 34.60 ºC, respectively. Seed germination was sensitive to drought stress and completely inhibited at a potential of -1 MPa, but it was tolerant to salinity. Salinity stress up to 90 mM had no effect over the M. officinalis seed germination, but the germination decreased by increasing the salt concentration. The drought and salinity required for 50% inhibition of maximum germination were 207 mM and -0.49 MPa, respectively. High percentage of seed germination (>92%) was observed at pH = 5-6 and decreased to 80% at acidic medium (pH 4) and to 42% at alkaline medium (pH 9) pH. Maximum seedling emergence occurred when the seeds were placed at 2 cm depth and decreased when increasing the depth of planting; no seed emerged from depths of 10 cm.

Efficiency of a reduced herbicide rate for Brachiaria brizantha control in sugarcane

At different growth stages, weeds present different sensitivities to herbicides. Thus, the registered herbicide rate may be reduced under specific conditions, while maintaining satisfactory weed control. This study evaluated the efficiency of reduced rates of the formulated herbicide mixture Velpar K WG® (hexazinone + diuron) + Volcane® (MSMA) for Brachiaria brizantha control at different growth stages. Optimum weed control efficiency was obtained when applying 50% of the recommended rate in younger plants (plants with one to four leaves). In late applications, it is necessary to increase the herbicide rates and, under these conditions, 90% of the recommended rate for (diuron + hexazinone) + MSMA was estimated to be the most economical one.