Chemical changes in argisols under irrigated grape production in the central São Francisco river valley, Brazil

This study compares the chemical composition of the solution and exchange complex of soil in a 3-year-old irrigated vineyard (Vitis vinifera L., Red Globe cultivar) with that of adjacent clearing in the native hyperxerophyllic 'caatinga' vegetation. The soils are classified as Plinthic Eutrophic Red-Yellow Argisol; according to Soil Taxonomy they are isohyperthermic Plinthustalfs. Detailed physiographic characterization revealed an impermeable gravel and cobble covering the crystalline rocks; the relief of this layer was more undulating than the level surface. Significant higher concentrations of extractable Na, K, Mg and Ca were observed within the vineyard. Lower soil acidity, higher Ca/Mg ratios, as well as lower sodium adsorption and Na/K ratios reflected additions of dolomitic lime, superphosphate and K-bearing fertilizers. As the water of the São Francisco River is of good quality for irrigation (C1S1), the increases in Na were primarily attributed to capillary rise from the saline groundwater table. None of the soil in the study area was found to be sodic. About 62% of the vineyard had an Ap horizon with salinity levels above 1.5dSm-1 (considered detrimental for grape production); according to average values for this horizon, a potential 13% reduction in grape production was predicted. Differences in chemical composition in function of distance to the collector canals were observed in the clearing, but not in the vineyard. The influence of differences in the elevations of the surface and impermeable layers, as well as pediment thickness, was generally weaker under irrigation. Under irrigation, soil moisture was greater in points of convergent surface waterflow; the effect of surface curvature on chemical properties, though less consistent, was also stronger in the vineyard.

QUANTIDADE DE FÓSFORO EXTRAÍDO PELAS SOLUÇÕES DE MEHLICH-1 E MEHLICH-3 EM RAZÃO DE DIFERENTES VELOCIDADES DE AGITAÇÃO, TEMPOS DE CONTATO E TEMPERATURAS

A extração de fósforo do solo pode ser comprometida pelas condições em que a análise é realizada e isso pode explicar a variabilidade nos resultados encontrados. O objetivo deste trabalho foi verificar a influência de desvios na velocidade de agitação, no tempo de contato e na temperatura sobre a extração do P pelos extratores Mehlich-1 (M-1) e Mehlich-3 (M-3) em amostras de solo. O estudo foi conduzido por meio de três experimentos executados com 11 amostras de solo provenientes da camada arável de Latossolo, Neossolo, Argissolo, Cambissolo, Planossolo, que são representativas das regiões geomorfológicas do Planalto e da Depressão Central do Estado do Rio Grande do Sul. Para todos os experimentos, adotou-se o delineamento experimental inteiramente casualizado em esquema fatorial 2 × 5 × 11, sendo dois extratores, cinco velocidades, temperaturas ou tempos de contato solo/solução e 11 tipos de solo, com quatro repetições. No primeiro experimento, a mistura solo:solução foi agitada em 80, 100, 120, 140 e 160 oscilações por min (opm). No segundo, após a agitação por 5 min, a mistura solo:solução foi deixada em repouso por períodos de tempo de oito, 12, 16, 20 e 24 h para retirada dos extratos. No terceiro, a temperatura de execução de todo o protocolo de análises foi mantida constante em 15, 20, 25, 30 e 35 °C. O aumento na velocidade de agitação de 120 até 160 opm aumentou a quantidade de P extraído pelos extratores. O aumento no tempo de contato antes da extração da alíquota elevou as quantidades de P extraído pelo M-1 e diminuiu para o M-3. Variações na temperatura não influenciaram significativamente o extrator M-1, mas o M-3 foi mais sensível a variações. Uma padronização na velocidade de agitação, no tempo de repouso e uma climatização dos laboratórios tornam-se necessárias para diminuir a interferência causada sobre as quantidades de P extraído pelos métodos M-1 e M-3 em amostras de solo.

Optical characterization of sol-gel glasses derived from Eu3+ complex-forming precursors

Fabrication of new optical devices based upon the incorporation of rare earth ions via sol-gel methods depends on elimination of dopant ion clusters and residual hydroxyl groups from the final material. The optical absorption and/or luminescence properties of luminescent rare earth ions are influenced by the local bonding environment and the distribution of the rare-earth dopants in the matrix. Typically, dopants are incorporated into gel via dissolution of soluble species into the initial precursor sol. In this work, Eu3+ is used as optical probe, to assess changes in the local environment. Results of emission, excitation, fluorescence line narrowing and lifetimes studies of Eu3+-doped gels derived from Si(OCH3)4 and fluorinated/chelate Eu3+ precursors are presented. The precursors used in the sol-gel synthesis were: tris (6,6,7,7,8,8,8-heptafluoro-2,2-dimethyl-3,5-octanedionate) Eu(III), Eu (III) trifluoromethanesulfonate, Eu(III) acetylacetonate hydrate, Eu (III) trifluoroacetate trihidrate, tris (2,2,6,6-tetramethyl-3,5- heptanedionate) Eu(III) and Eu(NO3)3.6H2O. The results were interpreted in terms of the evolution of the Eu3+ fluorescence in systems varying from solution to the gels densified to 800ºC. The lifetimes studies indicate that the fluorinated precursors are effective at reducing the water content in densified gels.

Adsorção do complexo H[Ru(III)Cl2(H2EDTA)] sobre a superfície da sílica gel modificada com [3-(2-aminoetil) aminopropil]trimetoxissilano em soluções etanólicas

Silica gel was functionalized with [3-(2-aminoethyl)aminopropyl]trimethoxysilane group (SF-AEATS) and the characterization by chemical analysis (N) and infrared spectroscopy confirmed the functionalization. The capacity of the modified silica to adsorb the complex Ru(III)-EDTA from ethanolic solution was studied. The selectivity coefficients of the complex formed on the support obtained was (Gñ), 2,07 x 10(4) L/mol and the average number of ligand bonded by one metal ion on the support (ñ) was ~ 1.

A técnica da reflectância difusa aplicada ao estudo da fluorescência de 2,3-naftalimidas n-substituídas com grupos alquila incluídas em b-ciclodextrina e adsorvidas em celulose microcristalina

The solution fluorescence of N-alkyl-2,3-naphthalimides (1-4) in polar protic and aprotic solvents was compared to the emission from solid samples resulting from the imide complexation with b-cyclodextrin or adsorption on the surface of microcrystalline cellulose. Solid samples of the inclusion complex 2,3-naphthalimides/b-cyclodextrin show maximum for fluorescence emission significantly different to the observed in methanolic solution. Beside this, a clear effect on the alkyl chain length could be observed for these samples which is probably due to differences in probe location inside the cyclodextrin cavity. The constancy for fluorescence quantum yield and fluorescence lifetime for the imides 1 - 4 adsorbed on microcrystalline cellulose suggests that, independently of the polarity of the solvent used for sample preparation, the probe is preferentially located on the cellulose surface. An increase of fluorescence quantum yield and fluorescence lifetime for solid samples, when compared to the values obtained in solution for the different solvents employed in this study (acetonitrile, methanol and water), is fully in accordance with a decrease of the probe mobility due to inclusion in b-cyclodextrin or to adsorption on cellulose.

The determination of the stoichiometry of the mixed complex of vanadium with hydrogen peroxide and with 4-(2-Pyridilazo) Resorcinol

The present study reports details of the stoichiometric characterization of the mixed complex system, V(H2O2)PAR, formed when vanadium adequately reacts with hydrogen peroxide and with 4-(2-Pyridilazo)Resorcinol. Also the presence of polynuclear species was investigated in order to elucidate about unambiguous assignment of the molar absorptivity, stability constant and composition of the complex. Two mathematical treatments methods of the experimental results were employed. From the results it can be concluded that this system corresponds to a mononuclear complex with 1:1:1 stoichiometry.

Utilização de um eletrodo de grafite-epóxi recoberto com [Zn(FEN)3][tetratris(4-clorofenil) borato]2 sensível a zinco(II) em meio 1,10-fenantrolina como eletrodo indicador em titulações potenciométricas de precipitação

The construction and analytical evaluation of a coated graphite-epoxy electrode sensitive to the zinc-1,10-phenantroline complex based on the [Zn(fen)3][tetrakis(4-chlorophenyl)borate]2 incorporated into a poly(vinylchloride) (PVC) matrix are described. A thin membrane film of this ion-pair, dibutylphthalate (DBPh) and PVC were deposited directly onto an electrically conductive graphite-epoxy support located inside a Perspex® tube. The best PVC polymeric membrane contains 65% (m/m) DBPh, 30% (m/m) PVC and 5% (m/m) of the ion-pair. This electrode shows a response of 19.5 mV dec-1 over the zinc(II) concentration range of 1.0 x 10-5 to 1.0 x 10-3 mol L-1 in 1,10-phenantroline medium, at pH 6.0. The response time was less than 20 seconds and the lifetime of this electrode was more than four months (over 1200 determinations by each polymeric membrane). It was successfully used as an indicator electrode in the potentiometric precipitation titration of zinc(II) ions.

Phase diagram and complex patterns in the modeling of the bromate-oxalic acid-Ce-acetone oscillating reaction

Simulations have been carried out on the bromate - oxalic acid - Ce(IV) - acetone oscillating reaction, under flow conditions, using Field and Boyd's model (J. Phys. Chem. 1985, 89, 3707). Many different complex dynamic behaviors were found, including simple periodic oscillations, complex periodic oscillations, quasiperiodicity and chaos. Some of these complex oscillations can be understood as belonging to a Farey sequence. The many different behaviors were systematized in a phase diagram which shows that some regions of complex patterns were nested with one inside the other. The existence of almost all known dynamic behavior for this system allows the suggestion that it can be used as a model for some very complex phenomena that occur in biological systems.

Síntese e caracterização estrutural do ligante isatina-3-(N4-benziltiossemicarbazona) e do seu complexo de mercúrio(II)

The reaction of 4-(phenyl)thiosemicarbazide with isatin yielded a new ligand, isatin-3-(N4-benzylthiosemicarbazone). Isatin-3-(N4-benzylthiosemicarbazone) deprotonated in ethanol/KOH reacts with an ethanolic solution of Hg(NO3)2 to give a mercury complex. The compounds were characterized by IR and X-ray single crystal structure determination. The X-ray studies revealed that the complex possesses a tetrahedral geometry with two deprotonated thiosemicarbazone ligands coordenated. The ligand and its mercury complex crystallize in the monoclinic (P2(1)/c) and triclinic (P-1) crystal system, respectively.

Electrocatalytic oxidation of methanol by the [Ru3O(OAc)6(py)2(CH3OH)]3+cluster: improving the metal-ligand electron transfer by accessing the higher oxidation states of a multicentered system

The [Ru3O(Ac)6(py)2(CH3OH)]+ cluster provides an effective electrocatalytic species for the oxidation of methanol under mild conditions. This complex exhibits characteristic electrochemical waves at -1.02, 0.15 and 1.18 V, associated with the Ru3III,II,II/Ru3III,III,II/Ru 3III,III,III /Ru3IV,III,III successive redox couples, respectively. Above 1.7 V, formation of two RuIV centers enhances the 2-electron oxidation of the methanol ligand yielding formaldehyde, in agreement with the theoretical evolution of the HOMO levels as a function of the oxidation states. This work illustrates an important strategy to improve the efficiency of the oxidation catalysis, by using a multicentered redox catalyst and accessing its multiple higher oxidation states.

Determination of aluminum in food samples after preconcentration as aluminon complex on microcrystalline naphthalene by spectrophotometry

A sensitive preconcentration procedure for spectrophotometeric determination of aluminum was developed. Aluminum as aluminon complex is adsorbed on microcrystalline naphthalene. The naphthalene containing the complex is dissolved in 3 mL of acetone and its absorbance is measured at 544 nm. The effect of various factors on the preconcentration of aluminum was investigated. The calibration graph was linear in the range of 1-60 mg L-1. The limit of detection was 0.52 mg L-1 and relative standard deviation for the determination of 5 mg L-1 was 2.65%. The proposed solid phase extraction procedure was applied to determination of aluminum in food samples.

Ternary surface complex: coadsorption of Cu(II), Zn(II), Cd(II) and nitrilotris(methylenephosphonic) acid onto boehmite

This work studies the effect of NTMP (nitrilotris(methylenephosphonic acid)) on the adsorption of Cu(II), Zn(II), and Cd(II) onto boehmite in the pH range 5-9.5. The data were analyzed using the 2-pK constant capacitance model (CCM) assuming ternary surface complex formation. Under stoichiometric conditions, NTMP is more effective for removing Cu(II) than Zn(II) from solution and the contribution of ternary surface complexes are important to model the adsorption of both metals. Under nonstoichiometric conditions and high surface loading with a Me(II)/NTMP ratio of 1:5, Cu(II) and Zn(II) adsorption is significantly suppressed. In the case of Cd(II) the free metal adsorption is the most dominant species.

Preparation and immobilization of diNOsarcobalt(III) complex in zeolite y for the catalyzed production of hydrogen peroxide

A complex cation, diNOsarcobalt(III), [Co(diNOsar)]3+, (diNOsar = 1,8-dinitro-3,6,10,13,16,19-hexaazabicyclo-[6.6.6]eicosane), was synthesized and immobilized in the cavities of a Y zeolite by the reaction of precursor species in the pores of the zeolite. The encapsulated material was compared to the compound diNOsarcobalt(III) chloride, [Co(diNOsar)]Cl3. Both diNOsarcobalt(III) chloride and the zeolite-encapsulated complex, [Co(diNOsar)]3+/zeolite, were obtained in high yield and characterized by ultraviolet-visible and infrared spectroscopy. X-ray diffraction demonstrated the incorporation of the complex cation into the pores of the zeolite. The catalytic production of hydrogen peroxide from oxygenated water confirmed the successful synthesis of the complex diNOsarcobalt(III) immobilized in the zeolite.

Garlic viral complex: identification of Potyviruses and Carlavirus in Central Brazil

Garlic viruses often occur in complex infections in nature. In this study, a garlic virus complex, collected in fields in Brazil, was purified. RT-PCR was performed using specific primers designed from the consensus regions of the coat protein genes of Onion yellow dwarf virus, a garlic strain (OYDV-G) and Leek yellow stripe virus (LYSV). cDNA of Garlic common latent virus (GCLV) was synthesized using oligo-dT and random primers. By these procedures individual garlic virus genomes were isolated and sequenced. The nucleotide sequence analysis associated with serological data reveals the presence of two Potyvirus OYDV-G and LYSV, and GCLV, a Carlavirus, simultaneously infecting garlic plants. Deduced amino acid sequences of the Brazilian isolates were compared with related viruses reported in different geographical regions of the world. The analysis showed closed relations considering the Brazilian isolates of OYDV-G and GCLV, and large divergence considering LYSV isolate. The detection of these virus species was confirmed by specific reactions observed when coat protein genes of the Brazilian isolates were used as probes in dot-blot and Southern blot hybridization assays. In field natural viral re-infection of virus-free garlic was evaluated.

Variability of the 3' terminal of the polymerase gene of Grapevine leafroll-associated virus 3 isolates from Vale do São Francisco, Brazil

Many viral diseases, including leafroll, which is of great economic importance, affect grapevines (Vitis spp.). A complex of eight viruses [Grapevine leafroll-associated virus (GLRaV) -1 to 8] is associated with this disease. The objective of this study was to compare the variability of the 3' terminal region of the polymerase gene of three isolates of GLRaV-3 (Grapevine leafroll-associated virus-3), from Submédio do Vale do Rio São Francisco (Petrolina-PE) with that of other isolates available at the GenBank, including an isolate from North America and another from Southern Brazil. The viral RNA was extracted from three infected ELISA reactive plants and a fragment of 340 bp was amplified, by RT-PCR, using primers that recognize that portion of the polymerase gene found between nucleotides 8267 and 8606. The three isolates from Vale do Rio São Francisco named Pet-1, Pet-2 and Pet-3, showed similarities ranging from 98% and 94%, respectively to the isolates from North America (AF037268) and Southern Brazilian (AF438411). Considering the whole genome, the main variation found was one amino acid change at position 2766 (F2766Y). These preliminary data indicate the existence of a natural variation among GLRaV-3 isolates from grapevines. This could be due to the vegetative propagation and long cycle of the plant, associated with the error-prone nature of RNA-dependent RNA polymerase.