Degradação de paracetamol empregando tecnologia oxidativa avançada baseada em fotocatálise heterogênea usando irradiação artificial e solar

In this work, the oxidation and mineralization of paracetamol, based in an advanced oxidative process promoted by heterogeneous photocatalysis, was evaluated. The action of two photocatalysts (titanium dioxide, and a composite based on the association between titanium dioxide and zinc phthalocyanine dye) was studied. First of all, experiments in laboratory scale were performed using as radiation font a 400 W high pressure mercury lamp. The mineralization of paracetamol, promoted by both photocatalysts, was evaluated working with 4L of solution containing 10 mg L-1 of paracetamol and 100 mg L-1 of photocatalyst. To find the best experimental conditions, the influence of hydrogen peroxide concentration and pH was evaluated for the reactions. The best results for the reactions in laboratory scale was obtained using 33,00 mg L-1 of hydrogen peroxide in natural pH (6,80). Under these conditions, 100% oxidation was reached in just 40 minutes of reaction using TiO2 P25, while the mineralization was 78%. Using the composite, the mineralization was 63% in 2 hours of reaction and a oxidation of almost 100% was reached after 60 minutes. A CPC reactor (compound parabolic concentrator) was employed in the expanded work scale, using the sun as irradiation source. In this case the experiments were performed using 50 L of aqueous solution containing 10 mg L-1 of paracetamol and 100 mg L-1 of photocatalyst. The assays were done at pH 3,00 and natural pH (6,80). The used concentration of hydrogen peroxide was 33,00 mg L-1, adopted after laboratory scale studies. The reaction at pH 3,00 shows to be more advantageous, since under natural pH (6,80), the use of deionized water was necessary to prepare the solutions, probably because the deleterious action of carbonate ions, known hydroxyl radical scavengers. Using solar irradiation, the reaction mediated by the composite was more efficient when compared with the assays under laboratory scale since the composite presents the advantage of promoting a better use of visible radiation. Under these conditions, the mineralization increased from 40% to 56% under pH 3,00. At natural pH the oxidation occurred more slowly and the mineralization decreased from 56% to 50%. Thus, the use of pH 3,00 will be more interesting in real scale applications, even if it is necessary the pH correction before the discard of the treated effluent to the environment.

Determinação voltamétrica de zinco empregando eletrodos quimicamente modificados com bismuto

This dissertation presents the development of voltammetric methods to zinc determination in multivitamin commercial samples, talc, and art materials for painting (soft pastel) combining an alkaline extraction with 1.0 mol L-1 NaOH aqueous solution and bismuth modified electrodes. Two electrodes were used to zinc quantification in the samples, bismuth film electrode (BiFE) plated in situ onto glassy carbon and carbon paste electrode chemically modified with strongly acidic ion exchange resin Amberlite® IR 120 and bismuth nanostructures (EPCAmbBi). It was verified that the best concentration of Bi3+ for Bi film deposition onto glassy carbon was 4.0 μmol L-1 using an 0.1 mol L-1 acetate buffer aqueous solution (pH = 4.5) as supporting electrolyte. The best condition to formation of Bi nanostructures in the EPC modified with 10 % Amberlite® IR 120 was the use of 30 s to pre-concentration (open circuit) in 0.5 mmol L-1 Bi3+ aqueous solution (pH 5.5) prepared with supporting electrolyte solution. The obtained analytical curve for Zn2+ using BiFE presented linear range from 0.5 to 5.0 μmol L-1, the limit of detection (LD) was 41 nmol L-1. For EPCAmbBi only one linear range was observed for the analytical curve varying the Zn2+ concentration from 0.05 to 8.2 μmol L-1, LD obtained in this curve it was equal to 10 nmol L-1. The EPCAmbBi presented the most intense and sharp anodic stripping peaks for Zn2+ presenting, therefore, a better voltammetric profile, with sensitivity higher than obtained with the BiFE. Moreover, the EPCAmbBi presented a LD lower than that obtained with the BiFE. Alkaline extraction was an efficient sample pretreatment to extract Zn2+ from solid samples, besides that, this procedure was less susceptible to interferences from Cu2+, since it remains at extracting vessel as insoluble Cu(OH)2. The combination of alkaline extraction with the EPCAmbBi is a simple, fast, efficient and low cost for the zinc determination in pharmaceutical formulations and art materials for painting (soft pastel) samples, which can be employed as a low-cost alternative method to the atomic absorption spectroscopy.

Avaliação das condições de precipitação do azul da Prússia sobre pó de grafite visando o desenvolvimento de eletrodos de pasta de carbono para a quantificação de nitrito

An amperometric FIA method for nitrite quantification based on nitrite electroreduction and employing a carbon paste electrode (CPE) chemically modified with iron hexacyanoferrate (HCF) as an amperometric detector was developed. The influence of experimental conditions on the preparation of the electrode materials was evaluated and the materials obtained in each study were used for the development of modified electrodes. The electrochemical sensors were prepared by a fast, simple, and inexpensive procedure, and the long-term performance of the electrodes were quite satisfactory as the stability was maintained over one year. HCF was an effective redox mediator for nitrite electroreduction in acidic media, allowing nitrite detection at +0.2 V vs. Ag/AgClsat, which is a potential free of possible interfering species that are normally present in food and water samples. The electrochemical cell used in the FIA system was similar to a batch injection analysis cell, enabling recirculation of the carrier solution. This is an attractive feature because it allows the use of a high flow rate (6 mL min-1) leading to high sensitivity and analysis speed, while keeping reagent consumption low. The proposed method had a detection limit of 9 μmol L-1 and was successfully employed for nitrite quantification in spiked water and sausage samples. The obtained results were in good agreement with those provided by the spectrophotometric official method. At a 95 % confidence level it was not observed statistical differences neither in nitrite content nor in the precision provided by both methods. The experimental conditions for the synthesis of HCF were optimized and the best electrode material was prepared by mixing FeCl3, K4[Fe(CN)6] and carbon powder subjected to an acid and thermal treatment (400 ºC), followed by ultrasonic agitation at 4 °C. This material was used to construct an electrode with improved analytical performance to reduce nitrite, which presented greater stability compared to HCF film electrodeposited on the EPC, showing that the preparation procedure of the electrode material is an effective strategy for the development of HCF modified electrodes.

Preparação de catalisadores para reações de esterificação do ácido oleico baseados em matrizes polímericas sulfonadas POLI(1- FENILETILENO) (PS) e POLI(1-CLOROETILENO) (PVC)

Chemical modification of polymer matrices is an alternative way to change its surface properties. The introduction of sulfonic acid groups in polymer matrices alter properties such as adhesion, wettability, biocampatibility, catalytic activity, among others. This paper describes the preparation of polymeric solid acid based on the chemical modification of poly (1-fenietileno) (PS) and Poly (1-chloroethylene) (PVC) by the introduction of sulfonic acid groups and the application of these polymers as catalysts in the esterification reaction of oleic acid with methanol. The modified materials were characterized by Infrared Spectroscopy, Elemental Analysis and titration acid-base of the acid groups. All techniques confirmed the chemical changes and the presence of sulfur associated with sulfonic acid groups or sulfates. The modified polymers excellent performance in the esterification reaction of oleic acid with methanol a degree of conversion higher than 90% for all investigated polymers (modified PS and PVC (5% w / w)), with a mass ratio of oleic acid: methanol 1:10 to 100 ° C. The best performance was observed for the modified PVC catalyst (PVCS) which showed low degree of swelling during the reactions is recovered by filtration different from that observed for polystyrene sulfonate (PSS). Given these facts, the PVCS was employed as a catalyst in the esterification reaction of oleic acid in different times and different temperatures to obtain the kinetic parameters of the reaction. Experimental data show a great fit for pseudo-homogeneous model of second order and activation energy value of 41.12 kJ mol -1, below that found in the literature for the uncatalyzed reaction, 68.65 kJ mol -1 .The PVCS exhibits good catalytic activity for 3 times of reuse, with a slight decrease in the third cycle, but with a conversion of about 78%. The results show that solid polymeric acid has good chemical stability for the application in esterification reaction of commercial importance with possible application in the biodiesel production. The advantages in use of this system are the increased reaction rate at about 150 times, at these test conditions, the replacement of sulfuric acid as a catalyst for this being the most corrosive and the possibility of reuse of the polymer for several cycles.

Caracterização e avaliação da atividade fotocatalítica de catalisadores baseados no TiO2, sintetizados mediante hidrólise em uma mistura de solventes

This study involved the synthesis of photocatalysts based on titanium dioxide (TiO2). The photocatalysts were synthesized by the sol-gel method using three different proportions of acetone (25%, 50% and 75% v/v) in water/acetone mixtures, in order to control the hydrolysis of the precursor of titanium (titanium tetraisopropoxide). Aiming to investigate the structural, morphological and electronic changes provoked by the use of the solvent mixtures, different methodologies were used to characterize the oxides, such as X-ray diffraction (XRD), RAMAN spectroscopy, UV-Vis diffuse reflectance spectroscopy, and measurements of specific surface area (BET). XRD combined to RAMAN analyses revealed that the products are two-phase highly crystalline oxides involving anatase as main phase and brookite. Besides, the refined XRD using the method of Rietveld demonstrated that the presence of acetone during the synthesis influenced in the composition of the crystalline phases, increasing the proportion of the brookite phase between 13 and 22%. The band gap energy of these oxides practically did not suffer changes as function of the synthesis conditions. As shown by the isotherm, these photocatalysts are mesoporous materials with mean diameter of pores of 7 nm and approximately 20% of porosity. The surface area of the oxides prepared by hydrolysis in presence of acetone was 12% higher compared to the bare oxide. After characterized, these oxides had their photocatalytic activities evaluated by photodegradation of the azo dyes Ponceau 4R (P4R), Tartrazine (TTZ) and Reactive Red 120 (RR120), and also by the ability to mediate the photocatalytic production of hydrogen. Using the most efficient photocatalyst, the mineralization achieved for the dyes P4R, RR120 and TTZ was of respectively 83%, 79% and 56% in 120 minutes of reaction, while the discoloration of P4R e RR120 reached 100% and 94% for TTZ. In addition, the same photocatalyst in the presence of 0.5% w/w of Platinum and suspended in a 5:1 v/v water/methanol mixture, produced 56 mmol of gaseous hydrogen in five hours of experiment, corresponding to a specific rate of hydrogen production of 139.5 mmol h-1 g-1.

Aditivo polimérico derivado de fonte renovável para aplicação em cimento asfáltico de petróleo

This study evaluated the effects of incorporating an additive from an agro-industrial residue, after some chemical modification reactions, to petroleum asphalt cement (CAP) through the polymerization reaction of a viscous polyol obtained by bagasse biomass oxypropylation reaction sugarcane with anhydrides. The polyol is obtained by biomass oxypropylation reaction with propylene oxide, the reaction was performed in an autoclave sealed with pressure and temperature control using 25 mL of OP for every 5 grams of biomass 200°C, which time reaction was two hours. The reaction is revealed by varying the system pressure, initially at atmospheric pressure to reach a maximum pressure value and its subsequent return to atmospheric pressure. For the choice of the most suitable reaction time for polymerization of the polyol with pyromellitic anhydride, the reaction was also conducted in an autoclave sealed with temperature controller (150 ° C) using 20 g of polyol, 1 g of sodium acetate (catalyst) and 8 g of pyromellitic anhydride with the times 30 and 60 minutes. The polymerized materials with different times were characterized by determining the relative viscosity and percentage content of extractable in cyclohexane / ethanol. Given the results with the polymerized material 30 minutes showed the lowest percentage content of extractives and an increased viscosity relative indicating that this time is highlighted with respect to time 60 minutes, because the material is possibly in the form of a crosslinked polymer. Given the choice of time of 30 minutes other polymerization reactions were performed with various anhydrides and other conditions employed different proportions by mass of polyol anhydrides we were referred to as condition I (20 g anhydride and 8 g of polyol), II (20 g anhydride and 20 g of polyol) and III (8 g anhydride and 20 g of polyol). The FTIR spectra of polymeric materials with different polymerization conditions used to prove the occurrence of chemical modification due to the appearance of a characteristic band ester groups (1750 cm-1) present in the polymerized material. He chose to work with the condition III, as is the condition which employs a larger amount of polyol, and even with the smaller amount of anhydride used FTIR spectra revealed that the polymerization reaction was performed. Among the various anhydrides (phthalic, maleic and pyromellitic) of the different conditions used that stood out before the solubility test with solvents analyzed was polymerized material with pyromellitic anhydride because the polymerized material likely in the form of a crosslinked polymer because it was insoluble or poorly soluble in the solvents tested. Polymerization of the polyol with pyromellitic anhydride using condition III, that is, BCPP30, CSPP30, PCPP30 e BCPPG30, provided an increase in thermal stability relative to material in the form of polyol. Applicability tests concerning the incorporation of 16% m / m BCPP30, CSPP30, PCPP30 e BCPPG30 additive in relation to the mass of 600 g CAP showed through characterization tests used, softening point, elastic recovery and marshall dosage, it is possible to use BCPP30 as an additive the conventional CAP, because even with the incorporation of this new additive modified CAP met the specifications of the appropriate standard.

Prospecção química e avaliação biológica de Banisteriopsis laevifolia (Malpighiaceae)

The Banisteriopsis genus is widespread in traditional medicine. This work aims to contribute with information about the chemical composition and on the evaluation of the biological activity of the essential oil, the ethanol extract of the leaves and partitions of the Banisteriopsis laevifolia. The phytochemical screeningtest of ethanol extract and partitions of leaves indicated the presence of flavonoids, terpenoids, saponins, phenols and steroids compounds. Nitrogenous compounds, characteristic of some species of this family, were not detected. Flavonoids were the predominant metabolite, with the highest concentrations on the partitions ethyl acetate and n-butanol. The antibacterial activity, antifungal and cytotoxicity of the essetial oil, ethanol extract and partitions were assyed by microdilution broth method (MBM), where the minimum inhibitory concentrations (MIC) were calculated. The ethanol extract and partitions did not inhibit growth against to Gram positive bacteria tested, with MIC less than 400 mg L-1. For the Gram negative bacteria tested, the hexane and hydroethanol partitios were more effective against F. nucleatum bacteria (MIC 100 ug mL-1). The ethanol extract showed antifungal activity with MIC of 31.2 mg L-1. Ethyl acetate and n-butanol partitions showed MIC 187.5 mg L-1 and 93.7 mg L-1, respectively, arousing interest for isolation studies. The antioxidant activity was evaluated by the DPPH free radical method. The ethanolic extract, ethyl acetate and n-butanol partitions were active, since they showed EC50 values (4.53 ug mL-1, 4.07 and 8.39 ug mL-1, respectively), values equivalent to the BHT (7.3 mg L-1). The analysis by HPLC-MS/MS of the most active fractions (ethyl acetate and n-butanol) identified phenolic compounds (flavonols and phenolic acids) which exert recognized biological activity. The GC-MS analysis of the essential oils from leaves collected in two periods studied (dry and wet), showed a small variation in the number of compounds. The major classes identified for the oil collected in the dry period were aliphatic alcohols (23,4%), terpenoids (18.7%), sterols (10.4%) and long-chain alkanes (9.2%) compounds. Terpenoids (26.8%) were the major class for the rain season. The major compounds (3Z) -hexenol, phytol and untriacontano are present in the two seasons but in different amounts (19.4%, 9.8% and 7.5% during the dry season, and 17.0 %, 14.9% and 15.3% in the rainy season, respectively). The essential oil from rainy season was not effective against to the oral bacteria Gram positive and Gram negative tested. However, showed significant antifungal activity with MIC 1000 mg L-1 against Candidas. Thus, the promising results with respect to biological assays of ethanolic extract and partitions from B. laevifolia contributed to the chemical and biological knowledge of the species B. laevifolia.

Aplicação de espectroscopia no infravermelho médio e calibração multivariada para quantificação de adulterantes e teor em biodiesel de óleo de palma com óleo de soja, soja residual e diesel

In this work, it was developed and validated methodologies that were based on the use of Infrared Spectroscopy Mid (MIR) combined with multivariate calibration Square Partial Least (PLS) to quantify adulterants such as soybean oil and residual soybean oil in methyl and ethyl palm biodiesels in the concentration range from 0.25 to 30.00 (%), as well as to determine methyl and ethyl palm biodiesel content in their binary mixtures with diesel in the concentration range from 0.25 to 30.00 (%). The prediction results showed that PLS models constructed are satisfactory. Errors Mean Square Forecast (RMSEP) of adulteration and content determination showed values of 0.2260 (%), with mean error (EM) with values below 1.93 (%). The models also showed a strong correlation between actual and predicted values, staying above 0.99974. No systematic errors were observed, in accordance to ASTM E1655- 05. Thus the built PLS models, may be a promising alternative in the quality control of this fuel for possible adulterations or to content determination.

Modelagem molecular voltada para a construção de um nanobiossensor para detecção do herbicida Imazaquin

In this study, our goal was develop and describe a molecular model of the enzyme-inhibiting interaction which can be used for an optimized projection of a Microscope Force Atomic nanobiosensor to detect pesticides molecules, used in agriculture, to evaluate its accordance with limit levels stipulated in valid legislation for its use. The studied herbicide (imazaquin) is a typical member of imidazolinone family and is an inhibitor of the enzymatic activity of Acetohydroxiacid Synthase (AHAS) enzyme that is responsible for the first step of pathway for the synthesis of side-chains in amino acids. The analysis of this enzyme property in the presence of its cofactors was made to obtain structural information and charge distribution of the molecular surface to evaluate its capacity of became immobilized on the Microscopy Atomic Force tip. The computational simulation of the system, using Molecular Dynamics, was possible with the force-field parameters for the cofactor and the herbicides obtained by the online tool SwissParam and it was implemented in force-field CHARMM27, used by software GROMACS; then appropriated simulations were made to validate the new parameters. The molecular orientation of the AHAS was defined based on electrostatic map and the availability of the herbicide in the active site. Steered Molecular Dynamics (SMD) Simulations, followed by quantum mechanics calculations for more representative frames, according to the sequential QM/MM methodology, in a specific direction of extraction of the herbicide from the active site. Therefore, external harmonic forces were applied with similar force constants of AFM cantilever for to simulate herbicide detection experiments by the proposed nanobiosensor. Force value of 1391 pN and binding energy of -14048.52 kJ mol-1 were calculated.

Obtenção de triacetato de celulose a partir do bagaço de cana-deaçúcar para revestimento de micropartículas de goma gelana e avaliação do seu perfil de liberação in vitro e da mucoadesão ex vivo

Oral route of administration is considered to be the most comfortable, safe and greater adaptation for patients. But, oral route presents some disadvantages such as drugs bioavailability and side effects on the stomach. Some technologies are studied to soften and/or resolve these problems, such as coating with polymeric films, which are able to protect the pharmaceutical form of the acid stomachic environment and to act in the drug release, and mucoadhesive systems, which allow the pharmaceutical form remains a greater time interval in the intestine, increasing the effectiveness of the drug. Cellulose triacetate (CTA) films were produced from cellulose extracted from sugar cane bagasse. The films were prepared with different morphologies (with and without water, acting as non-solvent) and concentrations (3, 6.5 and 10%) of CTA and characterized using scanning electron microscopy (SEM), water vapor permeability (WVP), puncture resistance (PR), enzymatic digestion (DE), and mucoadhesive force evaluation (MF). Microscopy showed the formation of symmetric and asymmetric morphologies. WVP data showed that more concentrated films have higher values for WVP; moreover, asymmetric films had higher values than symmetric films. PR measurements showed that symmetric membranes are more resistant than asymmetric ones. More concentrated films were also more puncture resistant, except for symmetric membranes with CTA concentrations of 6.5 and 10% that did not show significant differences. All of the films presented large mucoadhesive capacities independent of their morphology and CTA concentration. From the results of WVP and RP, a symmetric filme with 6.5% CTA showed better ability and mechanical resistance, therefore, was selected to serve as coating of gellan gum (GG) particles incorporating ketoprofen (KET), which was confirmed by SEM. The selected film presented low values in measurements of the swelling index (SI) and in a dissolution test (DT). TGA analysis showed that the CTA coating does not influence the thermal stability of the particles and there is no incompatibility evidence between CTA, GG and KET. Coated particles released 100% of the ketoprofen in 24 h, while uncoated particles released the same amount in 4 h. The results of this study highlight the potential of CTA in the development of new controlled oral delivery systems.

Determinação de teor de biodieseis de algodão e pinhão manso em misturas com diesel usando espectroscopia no infravermelho médio e quadrados mínimos parciais

Biodiesel is a renewable fuel derived from vegetable oils or animal fats, which can be a total or partial substitute for diesel. Since 2005, this fuel was introduced in the Brazilian energy matrix through Law 11.097 that determines the percentage of biodiesel added to diesel oil as well as monitoring the insertion of this fuel in market. The National Agency of Petroleum, Natural Gas and Biofuels (ANP) establish the obligation of adding 7% (v/v) of biodiesel to diesel commercialized in the country, making crucial the analytical control of this content. Therefore, in this study were developed and validated methodologies based on the use of Mid Infrared Spectroscopy (MIR) and Multivariate Calibration by Partial Least Squares (PLS) to quantify the methyl and ethyl biodiesels content of cotton and jatropha in binary blends with diesel at concentration range from 1.00 to 30.00% (v/v), since this is the range specified in standard ABNT NBR 15568. The biodiesels were produced from two routes, using ethanol or methanol, and evaluated according to the parameters: oxidative stability, water content, kinematic viscosity and density, presenting results according to ANP Resolution No. 45/2014. The built PLS models were validated on the basis of ASTM E1655-05 for Infrared Spectroscopy and Multivariate Calibration and ABNT NBR 15568, with satisfactory results due to RMSEP (Root Mean Square Error of Prediction) values below 0.08% (<0.1%), correlation coefficients (R) above 0.9997 and the absence of systematic error (bias). Therefore, the methodologies developed can be a promising alternative in the quality control of this fuel.

O ensino de química na educação de jovens e adultos do ensino médio no município de Itumbiara-GO

For this study, a research was conducted in order to answer the question "What chemistry teaching has been developed in the Youth and Adult Education (EJA) ?". The research provides an overview of the object to the proposed changes, leading students to live with different realities and investigating the issue of contextualization based on the daily lives of these students related to the subject of chemistry. The methodology focuses ethnographic research of the case study, in which a case is studied in depth using the participant observation. In the survey data a mixed qualitative and quantitative approach was used. The work involved 6 schools that offer adult education high school; 6 directors of these schools; 6 coordinators who work in adult education; 6 Chemistry teachers and 123 students of the EJA, level high school, enrolled in the 1st, 2nd, 3rd and 4th periods. The first stage of the research consisted of questionnaires in schools where everyone involved responded closed and open questions applied to each specific group. In the second stage two schools were selected in order to conduct a deeper knowledge of adult education through practical activities of Chemistry and subsequent interview conducted in groups with students. Three teachers were also interviewed to enable a deepening of issues relating to EJA and Chemistry Teaching. The interviews were analyzed by the technique of Discursive Textual Analysis (ATD). The main issues addressed in the questionnaires and interviews were on the school structure, reasons that lead students to drop out or remained in adult education and those who make the stay, the view of those involved of the importance of chemistry discipline for students of EJA and how this should be offered. It is necessary that we need to promote changes in the chemistry class and its activities, respecting the experiences and experience already gained by the student during his life story. Another factor to be highlighted is the need for ongoing training of teachers working in adult education. Note that your continued education is given more by the experience and the ways in which they try to overcome adverse situations. The Chemistry subject taught is not agree with the principles of EJA and practiced curriculum is just an adaptation or content reduction from the regular curriculum. The improvement in chemistry teaching of EJA will take place through a dialogue between those involved in the process, clearer educational policies and willingness to implement change. Thus the teaching of chemistry contribute to the students of the EJA are actually scientifically literate and integrated into society.

Estudo fitoquímico e biológico das folhas de Banisteriopsis argyrophylla (A. Juss.) B. Gates (Malpighiaceae)

With the increasing fungi resistance compared with existing drugs on the market and the side effects reported by some compounds with antioxidant properties and enzymatic inhibitors, in particular against α-amylase and α-glucosidase, the discovery of new compounds with biological potential, becomes a need. In this context, natural products can be an important source for the discovery of new active molecular architectures. Then, this study aimed to evaluate the antioxidant activity, the enzymatic inhibitory activity of α-amylase and α-glucosidase, the antifungal and cytotoxic activities of ethanolic extract (EE) the leaves of Banisteriopsis argyrophylla (Malpighiaceae) and their fractions, obtained by liquid-liquid extraction using solvents of increasing polarity. The antioxidant activity was evaluated by the free radical DPPH scavenging method (2,2-diphenyl-1-picrylhydrazyl) and the ethyl acetate fractions (FAE) and n-butanol (FB) were the most active, confirmed by the peak current and the oxidation potential obtained by differential pulse voltammetry (DPV). The inhibitory activity of the α-amylase and α-glucosidase was analyzed considering the reactions between substrates α-(2-chloro-4-nitrophenyl)-β-1,4-galactopiranosilmaltoside (Gal-α-G2-CNP) and 4-nitrophenyl-α-D-glucopyranoside (p-NPG), respectively. Initially, it was found that the EE showed considerable activity against α-amylase (EC50 = 2.89±0.1 μg m L–1) compared to the acarbose used as positive control (EC50 = 0.08±0.1 μg mL–1) and that did not showed promising activity against the α-glucosidase. After this observation we evaluated the inhibitory activity of α-amylase fractions, with FAE (EC50 = 2.33±0.1 μg mL–1) and FB (EC50 = 2.57 ± 0.1 μg mL–1) showing the best inhibitions. The antifungal activity was evaluated against Candida species, and the FAE had better antifungal potential (MIC's between 93.75 and 11.72 μg mL–1) compared with amphotericin as positive standard (MIC = 1.00 and 2.00 μg L–1 for C. parapsilosis and C. krusei used as controls, respectively). The EE (CC50 = 360.00 ± 12 μg mL–1) and fractions (CC50's> 270.00 μg mL–1) were considerably less toxic to Vero cells than the cisplatin used as positive control (CC50 = 7.01 ± 0 6 μg mL–1). The FAE showed the best results for the activities studied, this fraction was submitted to ultra performance liquid chromatography coupled with mass spectrometry (UPLC-MS)), and the following flavonoids have been identified: (±)-catechin, quercetin-3-O-β-D-Glc/ quercetin-3-O-β-D-Gal, quercetin-3-O-β-L-Ara, quercetin-3-O-β-D-Xyl, quercetin-3-O-α-L-Rha, kaempferol-3-O-α-L-Rha, quercetin-3-O-(2''-galoil)-α-L-Rha, quercetin-3-O-(3''-galoil)-α-L-Rha and kaempferol-3-O-(3''-galoil)-α-L-Rha,. FAE was submitted to column chromatography using C18 phase, and (±)-catechin was isolated (FAE-A1, 73 mg) and three fractions consisting of a mixture of flavonoids were obtained (FAE-A2, FAE-A3 and FAE-A4). These compounds were identified by thin layer chromatography (TLC) and (–)-ESI-MS. The (±)-catechin fraction showed an MIC = 2.83 μg ml–1 in assay using C. glabrata, with amphotericin as positive control. The fractions FAE-A2, FAE-A3, FAE-A4, showed less antifungal potential in tested concentrations. The identified flavonoids are described in the literature, regarding their antioxidant capacity and (±)-catechin, quercetin-3-O-Rha and kaempferol-3-O-Rha are described as α-amylase inhibitors. Thus, B. argyrophylla is an important species that produces compounds with antioxidant potential that can be related to the traditional use as anti-inflammatory and also has antifungal compounds and inhibitors of α-amylase. Therefore, these leaves are promising resources for the production of new drugs.