High-strength resorbable brushite bone cement with controlled drug-releasing capabilities

Brushite cements differ from apatite-forming compositions by consuming a lot of water in their setting reaction whereas apatite-forming cements consume little or no water at all. Only such cement systems that consume water during setting can theoretically produce near-zero porosity ceramics. This study aimed to produce such a brushite ceramic and investigated whether near elimination of porosity would prevent a burst release profile of incorporated antibiotics that is common to prior calcium phosphate cement delivery matrices. Through adjustment of the powder technological properties of the powder reactants, that is particle size and particle size distribution, and by adjusting citric acid concentration of the liquid phase to 800 mM, a relative porosity of as low as 11% of the brushite cement matrix could be achieved (a 60% reduction compared to previous studies), resulting in a wet unprecompacted compressive strength of 52 MPa (representing a more than 100% increase to previously reported results) with a workable setting time of 4.5 min of the cement paste. Up to 2 wt.% of vancomycin and ciprofloxacin could be incorporated into the cement system without loss of wet compressive strength. It was found that drug release rates could be controlled by the adjustable relative porosity of the cement system and burst release could be minimized and an almost linear release achieved, but the solubility of the antibiotic (vancomycin > ciprofloxacin) appeared also to be a crucial factor.

A study of some constituents in human female saliva

Changes in the concentration of some constituents in women's saliva during the menstrual cycle were studied. Saliva was used because it is easier to collect than other body fluids and is continuously available for analysis. Glucose, the enzyme 17-Acetyl-D-glucosaminidase (NAG) and Calcium which are saliva constituents and belong to three different chemical groups were selected for the study. Several analytical techniques were investigated. The fluorometric assay procedure was found to be the best because of its specificity and sensitivity for the estimation of these constituents. resides the fluorametric method a spectrophotometric method was used in the NAG determination and an atomic absorption method in the calcium estimation. Glucose was estimated by an enzymatic method. This is based on the reaction of glucose with the enzymes glucose oxidase and peroxidase to yield hydrogen peroxide, which in turn oxidises a non-fluorescent substrate, p-hydroxyphenylacetic acid, to a highly fluorescent product. The saliva samples in this determination had to be centrifuged at high speed, heated in a boiling water bath, centrifuged again and then treated with a mixture of cation and anion resins to remove the substances that inhibited the enzyme system. In the determination of the NAG activity the saliva samples were diluted with citric acid/phosphate buffer, and then centrifuged at high speed. The assay was based on the enzymic hydrolysis of the non-fluorescent substrate 4-Methyl-umbelli1eryl-p-D-glucosaminide to the highly fluorescent 4-Methyl-umbelliferone• Calcium was estimated by a fluorometric procedure based upon the measurement of the fluorescence produced by the complex formed between calcein blue and calcium, at pH 9 - 13. From the results obtained from the analysis of saliva samples of several women it was found that glucose showed a significant increase in its level around the expected time of ovulation. This was found in seven cycles out of ten. Similar results were found with the enzyme NAG. No significant change in the calcium levels was observe& at any particular time of the cycle. The levels of the glucose, the activity of the enzyme NAG and the concentration of the calcium were found to change daily, and to differ from one subject to another and in the same subject from cycle to cycle. The increase observed it salivary glucose levels and the enzyme NAG activity could be monitored to predict the time of ovulation.

Local and systemic delivery of a novel group of inhibitors of transglutaminase enzyme: A potential approach for treating of catheter-related complications and liver fibrosis

The present thesis investigates targeted (locally and systemically) delivery of a novel group of inhibitors of enzyme transglutaminases (TGs). TGs are a widely distributed group of enzymes that catalyse the formation of isopeptide bonds between the y-carboxamide group of protein-bound glutamines and the a-amino group of protein-bound lysines or polyamines. The first group of the novel inhibitors tested were the tluorescently labelled inhibitors of Factor XIIIa (FXIIIa). These small, non-toxic inhibitors have the potential to prevent stabilisation of thrombi by FXIIIa and consequently increase the natural rate of thrombolysis, in addition it reduces staphylococcal colonisation of catheters by inhibiting their FXIIIa¬mediated cross-linking to blood clot proteins on the central venous catheter (CVCs) surface. The aim of this work was to incorporate the FXIIIa inhibitor either within coating of polyurethane (PU) catheters or to integrate it into silicone catheters, so as to reduce the incidence of thrombotic occlusion and associated bacterial infection in CVCs. The initial work focused on the incorporation of FXIIIa inhibitors within polymeric coatings of PU catheters. After defining the key characteristics desired for an effective polymeric-coating, polyvinylpyrrolidone (PVP), poly(lactic-co-glycolic acid) (PLGA) or their combination were studies as polymers of choice for coating of the catheters_ The coating was conducted by dip-coating method in a polymer solution containing the inhibitor. Upon incubation of the inhibitor-and polymer-coated strips in buffer, PVP was dissolved instantly, generating fast and significant drug release, whilst PLGA did not dissolve, yielding a slow and an insufficient amount of drug release. Nevertheless, the drug release profile was enhanced upon employing a blend solution of PVP and PLGA. The second part of the study was to incorporate the FXIIIa inhibitor into a silicone elastomer; results demonstrated that FXIIIa inhibitor can be incorporated and released from silicone by using citric acid (CA) and sodium bicarbonate (SB) as additives and the drug release rate can be controlled by the amount of incorporated additives in the silicone matrix. Furthermore, it was deemed that the inhibitor was still biologically active subsequent to being released from the silicone elastomer strips. Morphological analysis confirmed the formation of channels and cracks inside the specimens upon the addition of CA and SB. Nevertheless, the tensile strength, in addition to Young's modulus of silicone elastomer strips, decreased constantly with an increasing amount of amalgamated CA/ SB in the formulations. According to our results, incorporation of FXIIIa inhibitor into catheters and other medical implant devices could offer new perspectives in preventing bio-material associated infections and thrombosis. The use of tissue transglutaminase (T02) inhibitor for treating of liver fibrosis was also investigated. Liver fibrosis is characterized by increased synthesis and decreased degradation of the extracellular matrix (ECM). Transglutaminase-mediated covalent cross-linking is involved in the stabilization of ECM in human liver fibrosis. Thus, TG2 inhibitors may be used to counteract the decreased degradation of the ECM. The potential of a liposome based drug delivery system for site specific delivery of the fluorescent TG2 inhibitor into the liver was investigated; results indicated that the TG2 inhibitor can be successfully integrated into liposomes and delivered to the liver, therefore demonstrating that liposomes can be employed for site-specific delivery of TG2 inhibitors into the liver and TG2 inhibitor incorporating liposomes could offer a new approach in treating liver fibrosis and its end stage disease cirrhosis.

Modelling a biochemical reaction with computational fluid dynamics

Earlier investigations (Cartland Glover et al., 2004) into the use of computational fluid dynamics (CFD) for the modelling of gas-liquid and gas-liquid-solid flow allowed a simple biochemical reaction model to be implemented. A single plane mesh was used to represent the transport and reaction of molasses, the mould Aspergillus niger and citric acid in a bubble column with a height to diameter aspect ratio of 20:1. Two specific growth rates were used to examine the impact that biomass growth had on the local solids concentration and the effect this had on the local hydrodynamics of the bubble column.