Sulfur concentrations and isotope ratios in sediments from Kiel Bay, western Baltic Sea

The isotope-ratios of sulfur-components in several sedimentologically different cores of recent marine sediments from Kiel Bay (Baltic Sea) were investigated. In addition, quantitative determinations were made on total sulfur, sulfate, sulfide, chloride, organic carbon, iron and watercontent in the sediment or in the pore-water solution. The investigations gave the following results: 1. The sulfur in the sediment (about 0.3 -2 % of the dry sample) was for the most part introduced into the sediment after sedimentation. This confirms the results of Kaplan et al. (1963, doi:10.1016/0016-7037(63)90074-7). The yield of Sulfur from organic material is very small (in our samples about 5-10% of the total sulfur in the sediment). 2. The sulfur bound in the sediment is taken from the sulfate of the interstitial water. During normal sedimentation, the exchange of sulfate by diffusion significant for changes in the sulfur-content goes down to a sediment depth of 4-6 cm. In this way the sulfate consumed by reduction and formation of sulfide or pyrite is mostly replaced. The uppermost layer of the sediment is an partly open system for the sulfur. The diagenesis of the sulfur is allochemical. 3. The isotope-values of the sediment-sulfur are largely influenced by the sulfur coming into the sediment by diffusion and being bound by bacteriological reduction. Due to the prevailing reduction of 32S and reverse-diffusion of sulfate into the open sea-water, an 32S enrichment takes place in the uppermost layer of the sediment. delta34S-values in the sediment range between -15 and -35 ? while seawater-sulfate has +20 ?. No relationship could be established between sedimentological or chemical changes and isotope-ratios. In the cores, successive sandy and clayly layers showed no change in the delta-values. The sedimentation rate, however, seems to influence isotope-ratios. In one core with low sedimentationrates the delta34S-values varied between -29 and -33 ?, while cores with higher sedimentationrates showed values between -17 and -24 ?. 4. As sediment depth increases, the pore-water sulfate shows decreasing concentrations (in a depth of 30-40 cm we found between 20 and 70 % of the seawater-values), and increasing delta 34S-values (in one case reaching more than +60 ?). The concentration of sulfide in the pore-water increases with sediment-depth (reaching 80 mg S/l in one case). The (delta34S-values of the pore-water-sulfide in all cores show increases paralleling the sulfate sulfur, with a nearly constant delta-distance of 50-60 ? in all cores. This seems to confirm the genetic relationship between the two components.

Chemical analysis of water samples of station M1_1207, Red Sea (Table 1-3)

Two water samples and two sediment samples taken in 1965 by the R. V. "Meteor" in the area of the hot salt brine of the Atlantis II-Deep were chemically investigated, and in addition the sediment samples were subjected to X-ray and optical analysis. The investigation of the sulfur-isotope-ratios showed the same values for all water samples. This information combined with the Ca-sulfate solubility data leads us to conclude that, for the most part, the sulfate content of the salt brine resulted from mixing along the boundary with the normal seawater. In this boundary area gypsum or anhydrite is formed which sinks down to the deeper layers of the salt brine where it is redisolved when the water becomes undersaturated. In the laboratory, formation of CaS04 precipitate resulted from both the reheating of the water sample from the uppermost zone of the salt brine to the in-situ-temperature as well as by the mixing of the water sample with normal Red Sea water. The iron and manganese delivered by the hot spring is separated within the area of the salt brine by their different redox-potentials. Iron is sedimented to a high amount within the salt brine, while, as evidenced by its small amounts in all sediment samples, the more easily reducible manganese is apparently carried out of the area before sedimentation can take place. The very good layering of the salt brine may be the result of the rough bottom topography with its several progressively higher levels allowing step-like enlargements of the surface areas of each successive layer. Each enlargement results in larger boundary areas along which more effective heat transfer and mixing with the next layer is possible. In the sediment samples up to 37.18% Fe is found, mostly bound as very poorly crystallized iron hydroxide. Pyrite is present in only very small amounts. We assume that the copper is bound mostly as sulfide, while the zinc is most likely present in an other form. The sulfur-isotope-investigations indicate that the sulfur in the sediment, bound as pyrite and sulfides, is not a result of bacterical sulfate-reduction in the iron-rich mud of the Atlantis II-Deep, but must have been brought up with the hot brine.

Description of manganese nodules and crust collected from the Hakuho Maru Cruise KH-68-3, July-August, 1968, in Northwestern Pacific Ocean

The cores and dredges described in this report were taken on the KH-68-3 Expedition in July-August, 1968 by the Ocean Research Institute, University of Tokyo from the Hakuho Maru. A total of 16 cores and dredges sites have been were.

Composition of aerosols collected in the Western Russian Arctic in August-September 1991

In August-September 1991 during the SPASIBA expedition (Scientific Program on the Arctic and Siberian Aquatorium) aboard R/V Yakov Smirnitzky in the Laptev Sea ten samples of aerosols were collected by nylon nets. A combined approach including various analytical techniques, such as single-particle analysis, instrumental neutron activation analysis, and atomic absorption spectrophotometry, was used to study composition of the samples. Mass concentration of coarse-grained (>0.001 mm) insoluble fraction of aerosols ranged from 80 to 460 ng/m**3. In all the samples remains of land vegetation were found to be the dominant component. Organic carbon content of the aerosols ranged from 23 to 49%. Inorganic part of the samples was represented mainly by alumosilicates and quartz. Anthropogenic ''fly ash'' particles were observed in all the samples. Temporal variations of element concentrations resulted from differences in air masses entering the studied area.