Mineralogy and geochemistry of sediments of the Cretaceous/Tertiary boundary at DSDP Holes 62-465 and 62-465A

The complete Paleocene section begins with the basal Tertiary Globigerina eugubina Zone. This zone occurs at 465A-3-3, 4 cm to 465A-3-3, 144 cm and belongs to Lithologic Unit I (Site 465 report, this volume), a homogeneous, white, moderately to highly disturbed nannofossil ooze.

Chemical and isotope compositions of bottom sediments from ODP Leg 168, Eastern Flank of the Juan de Fuca Ridge

Ten sites were drilled in the eastern flank of the Juan de Fuca Ridge (North East Pacific) along a 100 km-long east-west transect during Leg ODP 168. This study focuses on the mineralogical and chemical study of sediments that overly basaltic basement through which seawater circulates. Silicate authigenesis was observed in the sediment layer just above basement at sites located more than 30 km from the ridge axis. This sediment alteration is particularly abundant at ODP Sites 1031 and 1029 where authigenic formation of Fe-Mg rich smectite and zeolite and the dissolution of biogenic calcite are observed. Comparison of the distribution of the alteration in the basal sediment collected along this transect suggests that diffusional transport of aqueous solutes from the basement into the overlying sediment cannot produce the mineralogical and chemical changes in the basal sediments at Sites 1031 located on a basement topographic high, and at Site 1029 located at about 50 km from the ridge axis on a buried basement area. Vertical advection of basement fluid though the sediment section is required to produce this alteration. These processes are still active at Site 1031, based on systematic variations in pore-water profiles and temperatures obtained from stable isotopic data on calcium carbonates and the nature of authigenic minerals. At Site 1029, there is no present-day advection of basement fluids though the sediment section, suggesting that this is a relic site for fluid flow.

Mineralogy and chemical composition of ODP Sites 129-800 and 129-801

Sites 800 and 801 in the Pigafetta Basin allow the sedimentary history over the oldest remaining Pacific oceanic crust to be established. Six major deposition stages and events are defined by the main lithologic units from both sites. Mineralogical and chemical investigations were run on a large set of samples from these units. The data enable the evolution of the sediments and their depositional environments to be characterized in relation to the paleolatitudinal motion of the sites. The upper part of the basaltic crust at Site 801 displays a complex hydrothermal and alteration evolution expressed particularly by an ochre siliceous deposit comparable to that found in the Cyprus ophiolite. The oldest sedimentary cover at Site 801 was formed during the Callovian-Bathonian (stage 1) with red basal siliceous and metalliferous sediments similar to those found in supraophiolite sequences, and formed near an active ridge axis in an open ocean. Biosiliceous sedimentation prevailed throughout the Oxfordian to Campanian, with rare incursions of calcareous input during the middle Cretaceous (stages 2, 4, and 5). The biosiliceous sedimentation was drastically interrupted during the Aptian-Albian by thick volcaniclastic turbidite deposits (stage 3). The volcanogenic phases are pervasively altered and the successive secondary mineral parageneses (with smectites, celadonite, clinoptilolite, phillipsite, analcime, calcite, and quartz) define a "mineral stratigraphy" within these deposits. From this mineral stratigraphy, a similar lithologic layer is defined at the top of the Site 800 turbidite unit and the bottom of the Site 801 turbidite unit. Then, the two sites appear to have been located at the same distal distance from a volcanic source (hotspot). They crossed this locality, at about 10°S, at different times (latest Aptian for Site 800, middle Albian for Site 801). The Cretaceous siliceous sedimentation stopped during the late Campanian and was followed by deposition of Cenozoic pelagic red clay (stage 6). This deep-sea facies, which formed below the carbonate compensation depth, contains variable zeolite authigenesis in relation to the age of deposition, and records the global middle Cenozoic hiatus events. At the surface, the red clay from this part of the Pacific shows a greater detrital component than its equivalents from the central Pacific deep basins.

Mineralogy and geochemistry of Miocene tuff from ODP Hole 129-802A

Drilling at Ocean Drilling Program Site 802 in the central Mariana Basin, northwest Pacific Ocean, revealed an unexpected 222-m-thick sequence of well-cemented tuff of Miocene age. The deposits are unusual in that their source is presumably an unmapped seamount and they exhibit several peculiar petrological and mineralogical features. The well-developed secondary mineral sequence which includes analcime is rare in such relatively young, unburied deposits, in an area where there is little other evidence of hydrothermal activity. The massive tuff section also contains abundant fissure veins made of a rare silicate carbonate sulfate hydroxide hydrate of calcium, called thaumasite, which has not before been described in deep submarine deposits. The smectite-zeolite-thaumasite paragenesis coincides with the presence of chloride and calcium-enriched interstitial waters. The diagenetic evolution of the deposit appears to have been largely controlled by the depositional mode. The discharges of disaggregated and rejuvenated volcaniclasts seem to have been abrupt and repeated. The Miocene tuff at Site 802 thus provides new insights on the interactions between basaltic glass, biogenic phases, and seawater, in a specific deep-sea environment.

Geochemical and mineralogical analyses of clay-rich intervals in ODP Sites 166-1006 and 166-1007

The western flank of the Great Bahama Bank, drilled during ODP Leg 166 at seven sites, represents a prograding carbonate sequence from late Oligocene to Holocene [Eberli et al., Proc. ODP Init. Reports 166 (1997)]. The signatures of the detrital input and of diagenetic alteration are evident in clay enriched intervals from the most distal Sites 1006 and 1007 in the Straits of Florida. Mineralogical and chemical investigations (XRD, TEM, SEM, ICP-MS) run on bulk rocks and on the clay fractions enable the origin and evolution of silicate parageneses to be characterized. Plio-Pleistocene silt and clay interbeds contain detrital clay assemblages comprising chlorite, illite, interstratified illite smectite, smectite, kaolinite and palygorskite. The greater smectite input within late Pliocene units than in Pleistocene oozes may relate either varying source areas or change in paleoclimatic conditions and weathering intensity. The clay intervals from Miocene-upper Oligocene wackestone sections are fairly different, with prevalent smectite in the fine fraction, whose high crystallinity and Mg contents that point towards an authigenic origin. The lower Miocene section, below 1104 mbsf, at depths where compaction features are well developed, is particularly characterized by abundant authigenic Na-K-clinoptilolite filling foraminifer tests. The authigenic smectite and clinoptilolite paragenesis is recorded by the chemical trends, both of the sediment and the interstitial fluid. This diagenetic evolution implies Si- and Mg rich fluids circulating in deeper and older sequences. For lack of any local volcaniclastic input, the genesis of zeolite and the terms of water rock interaction are discussed. The location of the diagenetic front correlates with that of the seismic sequence boundary P2 dated as 23.2 Ma. This correspondence may allow the chronostratigraphic significance of some specific seismic reflections to be reassessed.

Geochemistry at DSDP Holes 80-550 amd 80-548

At Sites 548 and 550 of DSDP Leg 80 several condensed sedimentary sections contain various types of polymetallic crusts. The relationships between mineralogic and geochemical data in the sections have been studied in the context of the biostratigraphic and sedimentologic results. The diagenetic evolution during periods of low accumulation rate varies according to depth and sedimentary environment. At Site 548 on the continental margin, the phosphatic and manganiferous crusts are similar to those related to upwelling influences before Late Cretaceous deposition. At Site 550 the upper Paleocene cherts, deposited directly on oceanic crust, are overlain by pelagic brown clays containing diagenetic manganiferous concretions characterized by very high Sr and Ba contents. The origin of these small nodules is probably related to the authigenesis of fecal pellets. The upper Eocene indurated section is made up of authigenic zeolites, clays, and Fe-Mn phases and is similar to the volcanic-sedimentary deposits described in deep basins and seamounts of the Pacific. These crusts and a polynucleated nodule within the overlying sediments have geochemical characteristics (high Ni, Co, and Cu contents) similar to those formed in the deep ocean under volcanic influences during periods of low sedimentation rates or sedimentary hiatuses. Volcaniclastic material is ubiquitous and peculiarly abundant in Eocene sections and can be related to the volcanic formation of Iceland in the North Atlantic.

Geochemistry at DSDP Leg 70 Holes

The hydrothermal mounds on the southern flank of the Galapagos Spreading Center are characterized by the following main features: 1) They are located over a young basement (0.5 to 0.85 m.y. of age) in a region known for its high sedimentation rate (about 5 cm/10**3 y.) because it is part of the equatorial high biological productivity zone. 2) They are located in a region with generally high heat flow (8 to 10 HFU). The highest heat-flow measurements (up to 10**3 HFU) correspond to mound peaks (Williams et al., 1979), where temperatures up to 15°C were measured during a dive of the submersible Alvin (Corliss et al., 1978). 3) They are often located on small vertical faults which displace the basement by a few meters (Lonsdale, 1977) and affect the 25- to 50-meter-thick sediment cover. Most of these characteristics have also been observed in the other three known cases of hydrothermal deposits with mineral parageneses similar to that of the Galapagos mounds. However, the case of the hydrothermal mounds south of the Galapagos Spreading Center is unique because of the unusual thickness of the hydrothermal deposits present. The mounds are composed of several, up to 4.5-meter-thick, layers of green clays which, in one case (Hole 509B), are overlain by about 1.4 meters of Mn-oxide crust. We suspect that such a large accumulation of hydrothermal products results from the "funnelling" of the hydrothermal solutions exiting from a highly permeable basement along the faults. This chapter reports a preliminary study of those green clays collected by hydraulic piston coring of the Galapagos mounds during Deep Sea Drilling Project (DSDP) Leg 70 of the D/V Glomar Challenger. Green clays have also been reported from three presently or recently active hydrothermal areas in or close to spreading centers.

Geochemistry, mineralogy and isotopes at DSDP Hole 62-464

The relationships between mineralogical and geochemical data on the three successive sedimentary facies at Deep Sea Drilling Project Site 464 are studied. The evolution of siliceous biogenic sediments is derived from the analyses of one Fe-Ti smectite concretion, and of siliceous aggregates occurring in the pelagic "brown clays." Along the sedimentary section, the trace elements enriching the authigenic silicates and the Fe-Mn oxyhydroxides vary, depending on the marine environment. The proportion of clays and carbonates into the siliceous deposits controls the diagenetic evolution of silica making up the quartz aggregates from the "brown clay" or the cristobalite cherts.

Geochemistry at DSDP Leg 73 Holes

In the South Atlantic, at Sites 519 to 523, the dissolution of calcareous oozes ended in the formation of red clays rich in iron and manganese. The early authigenesis of manganese oxides and clays is described in Miocene marly calcareous oozes. The mineralogical and geochemical influences of basaltic basement weathering are shown by the occurrence of palagonite, authigenic clays, and oxides in the basal sediments. The development of red clay facies can be inhibited by local topographic and paleoceanographic changes, as at Site 520.

Basal dolomitic sediments ofthe Tyrrhenian Sea

Basal dolomitic sediments were recovered at three drill sites in the Tyrrhenian Sea during Ocean Drilling Program (ODP) Leg 107 (Sites 650, 651, and 655). These sediments overlie the basaltic basement complex and are enriched in iron, and in some instances, also in manganese. The manganese enrichments, together with a very slight enrichment in trace transition elements, strongly suggest that the basal sediments have an affinity to deep-sea metalliferous deposits of hydrothermal origin. At Sites 651 and 655, the dolostones contain variable amounts of authigenic palygorskite, a Mgrich clay mineral. At Site 651, the basal sediments are 40 m thick and contain nonstoichiometric dolomite, sometimes Ca rich, but primarily Mg rich. The occurrence of Mg-rich dolomite with excess Mg up to 4% is unusual for the deep-sea environment; it may be associated with a hydrothermally driven flux of altered sea water through the directly underlying basement complex, which comprises basalt, dolerite, and serpentinized peridotite. Low-temperature alteration of the basement complex could produce solutions enriched in Mg. Oxygen-isotope equilibrium temperatures indicate that all of the studied dolomites formed under low-temperature conditions (i.e., < 70?C). The carbon-isotope compositions, together with the strong isotopic covariance, suggest that the Mg-rich dolomite precipitated more rapidly than the Carich dolomite. We suggest that the low-temperature, hydrothermal convection of Mg-rich solutions through the basal sediments in this back-arc basin environment (1) overcame kinetic problems related to the formation of massive dolostones, and (2) provided a mass-transport mechanism for dolomitization.

Sedimentology and geochemistry of ODP Leg 129 siliceous deposits

Siliceous deposits drilled on Ocean Drilling Program Leg 129 accumulated within a few degrees of the equator during the Jurassic through early Tertiary, as constrained by paleomagnetic data. During the Jurassic and Early Cretaceous, radiolarian ooze, mixed with a minor amount of pelagic clay, was deposited near the equator, and overall accumulation rates were moderate to low. At a smaller scale, in more detail, periods of relatively higher accumulation rates alternated with periods of very low accumulation rates. Higher rates are represented by radiolarite and limestone; lower rates are represented by radiolarian claystone. Our limited data from Leg 129 suggests that accumulation of biogenic deposits was not symmetrical about the equator or consistent over time. In the Jurassic, sedimentation was siliceous; in the Cretaceous there was significant calcareous deposition; in the Tertiary claystone indicates significantly lower accumulation rates at least the northern part of the equatorial zone. Accumulation rates for Leg 129 deposits in the Cretaceous were higher in the southern part of the equatorial zone than in the northern part, and the southern side of this high productivity zone extended to approximately 15°S, while the northern side extended only to about 5°N. Accumulation rates are influenced by relative contributions from various sediment sources. Several elements and element ratios are useful for discriminating sedimentary sources for the equatorial depositional environments. Silica partitioning calculations indicate that silica is dominantly of biogenic origin, with a detrital component in the volcaniclastic turbidite units, and a small hydrothermal component in the basal sediments on spreading ridge basement of Jurassic age at Site 801. Iron in Leg 129 sediments is dominantly of detrital origin, highest in the volcaniclastic units, with a minor hydrothermal component in the basal sediments at Site 801. Manganese concentrations are highest in the units with the lowest accumulation rates. Fe/Mn ratios are >3 in all units, indicating negligible hydrothermal influence. Magnesium and aluminum concentrations are highest in the volcaniclastic units and in the basal sediments at Site 801. Phosphorous is very low in abundance and may be detrital, derived from fish parts. Boron is virtually absent, as is typical of deep-water deposits. Rare earth element concentrations are slightly higher in the volcaniclastic deposits, suggesting a detrital source, and lower in the rest of the lithologic units. Rare earth element abundances are also low relative to "average shale." Rare earth element patterns indicate all samples are light rare earth element enriched. Siliceous deposits in the volcaniclastic units have patterns which lack a cerium anomaly, suggesting some input of rare earth elements from a detrital source; most other units have a distinct negative Ce anomaly similar to seawater, suggesting a seawater source, through adsorption either onto biogenic tests or incorporation into authigenic minerals for Ce in these units. The Al/(Al + Fe + Mn) ratio indicates that there is some detrital component in all the units sampled. This ratio plotted against Fe/Ti shows that all samples plot near the detrital and basalt end-members, except for the basal samples from Site 801, which show a clear trend toward the hydrothermal end-member. The results of these plots and the association of high Fe with high Mg and Al indicate the detrital component is dominantly volcaniclastic, but the presence of potassium in some samples suggests some terrigenous material may also be present, most likely in the form of eolian clay. On Al-Fe-Mn ternary plots, samples from all three sites show a trend from biogenic ooze at the top of the section downhole to oceanic basalt. On Si-Fe-Mn ternary plots, the samples from all three sites fall on a trend between equatorial mid-ocean spreading ridges and north Pacific red clay. Copper-barium ratios show units that have low accumulation rates plot in the authigenic field, and radiolarite and limestone samples that have high accumulation rates fall in the biogenic field.

Mineralogy and geochemistry of sedimentary deposits at DSDP Leg 55 Holes

The four holes (including a re-entry hole) drilled at Site 433 allow determination of the sedimentary sequence of Suiko Seamount in the Emperor chain. The holes are in a small graben basin situated within a lateral lagoon on the seamount. The sedimentary deposits range from the Paleocene to the upper Pliocene and are not uniform and continuous. A major hiatus exists at the top of the lower Eocene reef sediment, below the lower and upper Miocene pelagic sediments. The depositional history and succession of environments are shown by mineralogical and geochemical changes in the sediments.

Description and geochemistry of DSDP Leg 55 Holes

One of the objectives of Leg 55 was to investigate the Tertiary history of sedimentation and environment on the Emperor Seamounts after their volcanic activity. For the three first sites, 430, 431, and 432, drilled on Ojin, Nintoku, and Yömei Seamounts, the Neogene sedimentary deposits are not well represented and are not typical pelagic sediments. Except for two holes (430A and 432), where we found calcareous oozes, the sediments are heterogeneous sands, gravels, and pebbly mudstones with a wide range in grain size and composition. Two phenomena characterize these deposits: the inheritance of volcaniclastic material and its alteration, and the authigenesis of secondary minerals including silicates, phosphates, and ferromanganese oxides formed under volcanic influence in a marine environment.