Concentrations and accumulation rates of chemical elements and sediment components in sediments of central equatorial Pacific, DSDP data

Accumulation rates of Mg, Al, Si, Mn, Fe, Ni, Cu, Zn, opal, and calcium carbonate have been calculated from their concentrations in samples from equatorial Deep Sea Drilling Project sites. Maps of element accumulation rates and of Q-mode factors derived from raw data indicate that the flux of trace metals to equatorial Pacific sediments has varied markedly through time and space in response to changes in the relative and absolute influence of several depositional influences: biogenic, detrital, authigenic, and hydrothermal sedimentation. Biologically derived material dominates the sediment of the equatorial Pacific. The distributions of Cu and Zn are most influenced by surface-water biological activity, but Ni, Al, Fe, and Mn are also incorporated into biological material. All of these elements have equatorial accumulation maxima similar to those of opal and calcium carbonate at times during the past 50 m.y. Detritus distributed by trade winds and equatorial surface circulation contributes Al, non-biogenic Si, Fe, and Mg to the region. Detrital sediment is most important in areas with a small supply of biogenic debris and low bulk-accumulation rates. Al accumulation generally increases toward the north and east, indicating its continental source and distribution by the northeast trade winds. Maxima in biological productivity during middle Eocene and latest Miocene to early Pliocene time and concomitant well-developed surface circulation contributed toward temporal maxima in the accumulation rates of Cu, Zn, Ni, and Al in sediments of those ages. Authigenic material is also important only where bulk-sediment accumulation rates are low. Ni, Cu, Zn, and sometimes Mn are associated with this sediment. Fe is almost entirely of hydrothermal origin. Mn is primarily hydrothermal, but some is probably scavenged from sea water by amorphous iron hydroxide floes along with other elements concentrated in hydrothermal sediments, Ni, Cu, and Zn. During the past 50 m.y. all of these elements accumulated over the East Pacific Rise at rates nearly an order of magnitude higher than those at non-rise-crest sites. In addition, factor analysis indicates that some of this material is carried substantial distances to the west of the rise crest. Accumulation rates of Fe in basal metalliferous sediments indicate that the hydrothermal activity that supplied amorphous Fe oxides to the East Pacific Rise areas was most intense during middle Eocene and late Miocene to early Pliocene time.

Uranium and thorium isotopes and sedimentation rates in metalliferous sediments from the western flank of the East Pacific Rise at 21°-22°S

Isotopic compositions of uranium (234U and 238U) and thorium (230Th and 232Th) were measured in metalliferous sediments from the western flank of the East Pacific Rise at 21°-22°S, in the area of hydrothermal activity and massive sulfide accumulation at the axis of the EPR. Concentration of 232Th (on the carbonate-free base) is consistent with composition of mafic extrusive rocks; isotope ratios 232Th/238U and 234U/238U indicate that about 70% of uranium passes into sediments from sea water with hydrothermal iron hydroxide. Mean sedimentation rates are calculated for seven cores by the nonequilibrium 230Th method with use of the constant concentration model. Flux of 230Th to bottom sediments is calculated and its mean value is used to determine sedimentation rate in four other cores. The constant flux model is used to calculate change of sedimentation rate with depth for seven cores over time interval of 100-300 ky. Sedimentation rates varied not much (0.3-0.6 cm/ky). The greatest changes occurred in two cores: one located near massive sulfide structures, and another near the spreading axis. Determinations of mean rates by the radiocarbon method and the nonequilibrium thorium method are in good agreement.

Chemical and mineral compositions of basalts from the Pacific Ocean, DSDP data

Mineral and chemical alterations of basalts were studied in the upper part of the ocean crust using data of deep-sea drilling from D/S Glomar Challenger in the main structures of the Pacific floor. Extraction of majority of chemical elements (including heavy metals) from basalts results mainly from their interaction with heated sea water. As a result mineralized hydrothermal solutions are formed. On entering the ocean they influence greatly on ocean sedimentation and ore formation.

Chemical analysis of water samples of station M1_1207, Red Sea (Table 1-3)

Two water samples and two sediment samples taken in 1965 by the R. V. "Meteor" in the area of the hot salt brine of the Atlantis II-Deep were chemically investigated, and in addition the sediment samples were subjected to X-ray and optical analysis. The investigation of the sulfur-isotope-ratios showed the same values for all water samples. This information combined with the Ca-sulfate solubility data leads us to conclude that, for the most part, the sulfate content of the salt brine resulted from mixing along the boundary with the normal seawater. In this boundary area gypsum or anhydrite is formed which sinks down to the deeper layers of the salt brine where it is redisolved when the water becomes undersaturated. In the laboratory, formation of CaS04 precipitate resulted from both the reheating of the water sample from the uppermost zone of the salt brine to the in-situ-temperature as well as by the mixing of the water sample with normal Red Sea water. The iron and manganese delivered by the hot spring is separated within the area of the salt brine by their different redox-potentials. Iron is sedimented to a high amount within the salt brine, while, as evidenced by its small amounts in all sediment samples, the more easily reducible manganese is apparently carried out of the area before sedimentation can take place. The very good layering of the salt brine may be the result of the rough bottom topography with its several progressively higher levels allowing step-like enlargements of the surface areas of each successive layer. Each enlargement results in larger boundary areas along which more effective heat transfer and mixing with the next layer is possible. In the sediment samples up to 37.18% Fe is found, mostly bound as very poorly crystallized iron hydroxide. Pyrite is present in only very small amounts. We assume that the copper is bound mostly as sulfide, while the zinc is most likely present in an other form. The sulfur-isotope-investigations indicate that the sulfur in the sediment, bound as pyrite and sulfides, is not a result of bacterical sulfate-reduction in the iron-rich mud of the Atlantis II-Deep, but must have been brought up with the hot brine.

(Table 1) Sulfur and oxygen isotopes from two anhydrite samples recovered from DSDP Hole 70-504B

The first anhydrite reported from oceanic basalts occurs in altered basalts drilled during DSDP Leg 70 from Hole 504B. Anhydrite has been identified in several samples, two of which were studied in detail. Anhydrite in Sample 504B-40-3 (130-135 cm), which was acquired at 310 meters sub-basement, occurs in a dolerite at the center of a vug rimmed by saponite and calcite. Red iron-hydroxide-rich alteration halos occur from 0 to 310 meters sub-basement; primary sulfides in these halos are oxidized, and the rocks have lost large amounts of sulfur. The anhydrite in this sample has a d34S value of 18.5 per mil, and it is interpreted to have formed from a fluid containing a mixture of seawater sulfate (20.9 per mil) and basaltic sulfur (0 per mil) released during the oxidation of primary sulfides. Anhydrite in Sample 504B-48-3 (14-18 cm), which was found at 376 meters sub-basement, occurs intergrown with gyrolite at the center of a 1-cm-wide vein that is rimmed by saponite and quartz. At sub-basement depths below 310 meters to the bottom of the Leg 70 section (562 m sub-basement), the rocks exhibit the effects of anoxic alteration with common secondary pyrite. Anhydrite in Sample 504B-48-3 (14-18 cm) has a d34S value of 36.7 per mil, and it is interpreted to have formed from seawater-derived fluids enriched in 34S through sulfate reduction. Temperatures of alteration calculated from oxygen isotope data range from 60 to 100°C. Sulfate reduction may have occurred in situ, or elsewhere at higher temperature, possibly deeper in the crust. The secondary mineral paragenetic sequence indicates a progressive decrease in Mg and increase in Ca in the circulating fluids. This eventually led to anhydrite formation late in the alteration process.

(Table 1, page 168) Iron, manganese, and phosphorus concentrations in Fe-Mn-concretions from the Gulf of Bothnia, northern Baltic Sea

Fe-Mn-concretions of a spheroidal type were found according to electron probe determinations to consist of alternating iron- and manganese-rich layers. This pattern was ascribed to seasonal variations in the physico-chemical conditions governing the precipitation of the hydrous oxides of iron and manganese. Calculations based on the rhythmic growth of the concretions investigated gave a mean accumulation rate of 0.15-0.20 mm/yr. The rather high phosphorus content (average 3.5 % P2O5) of the concretions was found to be concentrated in the iron-rich layers, probably as a result of the scavenging effect of ferric hydroxide.