Oxygen-isotope composition, temperature and depth of formation of chert at DSDP Leg 62 Holes

We measured oxygen-isotope compositions of 16 siliceous rocks from Deep Sea Drilling Project Sites 463, 464, 465, and 466 (Leg 62). Samples are from deposits that range in age from about 40 to 103 m.y. and that occur at sub-bottom depths of 9 to 461 meters. Mean d18O values range from 28.4 to 36.8 per mil and 36.0 ± 0.3 per mil for quartz-rich and opal-CTrich rocks, respectively. d18O values in chert decrease with increasing sub-bottom depth; the slope of the d18O/depth curve is less steep for Site 464 than for the other sites which indicates that chert at Site 464 formed at higher temperatures than chert at Sites 463, 465, and 466. Temperatures of formation of cherts were 7 to 42°C, using the silica-water fractionation factor of Knauth and Epstein (1976), or 19 to 56°C, using the equation of Clayton et al. (1972). Temperatures in the sediment where the cherts now occur are lower than their isotopically determined temperatures of formation, which means that the cherts record an earlier history when temperatures in the sediment section were greater. Estimated sediment temperatures when the cherts formed are comparable to, but generally slightly lower than, those calculated from Knauth and Epstein's equation. The isotopic composition of cherts is more closely related to environment of formation (diagenetic environment) or paleogeothermal gradients, than to paleoclimates (bottom-water temperatures). Opal-CT-rich rocks may better record paleo-bottom-water temperature. In Leg 62 cherts, better crystallinity of quartz corresponds to lower d18O values; this implies progressively higher temperatures of equilibration between quartz and water during maturation of quartz. The interrelationship of d18O and crystallinity is noted also in continental-margin deposits such as the Monterey Formation - but for higher temperatures. The apparent temperature difference between open-ocean and continental-margin deposits can be explained by the dominant control of temperature on silica transformation in the rapidly deposited continental-margin deposits, whereas time, as well as temperature, has a strong influence on the transformations in open-ocean deposits. Comparisons between the chemistry and d18O values of cherts reveal two apparent trends: both boron and SiO2 increase as d18O increases. However, the correspondence between SiO2 and d18O is only apparent, because the two cherts lowest in SiO2 are also the most deeply buried, so the trend actually reflects depth of burial. The correspondence between boron and d18O supports the conclusion that boron is incorporated in the quartz crystal structure during precipitation

Chemical composition of sediments from DSDP Hole 149

The diagenesis and geochemical evolution of deep-sea sediments are controlled by the interaction between sediments and their associated pore waters. With increasing depth, the pore water of Hole 149 (DSDP) exhibits a strong depletion in Mg and a corresponding enrichment in Ca, while the alkalinity remains relatively constant. Dissolved SiO2 is nearly constant in the upper 100 m of sediment, but is highly enriched in the deepest pore waters. The pore waters exhibit a depletion in K with increasing depth, and O18/O16 pore water ratios also decrease. The sediment section has three zones of sedimentary regimes with increasing depth in the drill hole: an upper 100 m section of detrital clays, a middle section enriched in calc-akalic volcanics which have undergone submarine weathering to a smectite phase, and a lower section of siliceous ooze which still has a diagenetic smectite phase. The quartz-feldspar ratios and O18/O16 composition of the silicate phases are in agreement with these interpretations. The submarine weathering of volcanics to a smectite can account for the observed pore water gradients. Volcanics release Ca and Mg to the pore waters causing the alkalinity values to increase. Smectite is formed, depletes the pore waters in Mg and O18 and causes the alkalinity to decrease. The net reaction allows for the observed relationship between pore water Ca and Mg gradients with little net change in alkalinity. Given the abundance of volcanics in many deep-sea sediments, especially in lower sections which often form near ridge crests, the submarine formation of smectite may be an additional oceanic Mg sink which has not yet been fully considered.

Mud, sand, heavy and light minerals composition in lower Cretaceous at DSDP Hole 93-603B

During the drilling of Hole 603B on Deep Sea Drilling Project Leg 93, an unexpected series of sand-, silt-, and claystone turbidites was encountered from Cores 603B-45 through -76 (1224-1512 m sub-bottom depth). Complete and truncated Bouma sequences were observed, some indicating deposition by debris flows. Sand emplacement culminated with the deposition of a 30-m-thick, unconsolidated sand unit (Cores 603B-48 through -45). The purpose of this preliminary study is to determine the nature of the heavy mineral suites of this sediment in order to make tentative correlations with onshore equivalents. The heavy mineralogy of Lower Cretaceous North American mid-Atlantic coastal plain sediment has been extensively studied. This sediment is classified as the Potomac Group, which has a varied heavy mineral suite in its lower part (Patuxent Formation), and a limited suite in its upper part (Patapsco Formation). The results of this study reveal a similar trend in the heavy mineral suites of sediment in Hole 603B. Hauterivian through lower Barremian sediment has a heavy mineral suite that is dominated by zircon, apatite, and garnet, with minor amounts of staurolite and kyanite. Beginning in the mid-Barremian, a new source of sediment becomes dominant, one which supplies an epidote-rich heavy mineral suite. The results of the textural analyses show that average grain size of the light mineral fraction increases upsection, whereas sorting decreases. The epidote-rich source may have delivered sediment with a slightly coarser mean grain size. This sediment may represent a more direct continental input at times of maximum turbidite activity (mid-Barremian) and during deposition of the upper, unconsolidated sand unit.