(Table 1) Summary of basalt unit thickness, vesicularity, number of flow units, and average porosity at ODP Site 135-839

An inflatable drill-string packer was used at Site 839 to measure the bulk in-situ permeability within basalts cored in Hole 839B. The packer was inflated at two depths, 398.2 and 326.9 mbsf; all on-board information indicated that the packer mechanically closed off the borehole, although apparently the packer hydraulically sealed the borehole only at 398.2 mbsf. Two pulse tests were run at each depth, two constant-rate injection tests were run at the first set, and four were run at the second. Of these, only the constant-rate injection tests at the first set yielded a permeability, calculated as ranging from 1 to 5 * 10**-12 m**2. Pulse tests and constant-rate injection tests for the second set did not yield valid data. The measured permeability is an upper limit; if the packer leaked during the experiments, the basalt would be less permeable. In comparison, permeabilities measured at other Deep Sea Drilling Project and Ocean Drilling Program sites in pillow basalts and flows similar to those measured in Hole 839B are mainly about 10**-13 to 10**-14 m**2. Thus, if our results are valid, the basalts at Site 839 are more permeable than ocean-floor basalts investigated elsewhere. Based on other supporting evidence, we consider these results to be a valid measure of the permeability of the basalts. Temperature data and the geochemical and geotechnical properties of the drilled sediments all indicate that the site is strongly affected by fluid flow. The heat flow is very much less than expected in young oceanic basalts, probably a result of rapid fluid circulation through the crust. The geochemistry of pore fluids is similar to that of seawater, indicating seawater flow through the sediments, and sediments are uniformly underconsolidated for their burial depth, again indicating probable fluid flow. The basalts are highly vesicular. However, the vesicularity can only account for part of the average porosity measured on the neutron porosity well log; the remainder of the measured porosity is likely present as voids and fractures within and between thin-bedded basalts. Core samples, together with porosity, density, and resistivity well-log data show locations where the basalt section is thin bedded and probably has from 15% to 35% void and fracture porosity. Thus, the measured permeability seems reasonable with respect to the high measured porosity. Much of the fluid flow at Site 839 could be directed through highly porous and permeable zones within and between the basalt flows and in the sediment layer just above the basalt. Thus, the permeability measurements give an indication of where and how fluid flow may occur within the oceanic crust of the Lau Basin.

Sample information and classification of lower Miocene gravity-flow types of sediment core CRP-1 (Table 1)

Nineteen samples of the Cape Roberts-1 drillcore were taken from Miocene- age deposits, from 90.25 - 146.50 metres below seafloor (mbsf) for thin section and laser grain-size analysis. Using the grain-size distribution, detailed core logging, X-radiography and thin-section analysis of microstructures, coupled with a statistical grouping of the grain-size data, three main styles of gravity-flow sedimentation were revealed. Thin (centimetre-scale) muddy debris-flow deposits are the most common and are possibly tirggered by debris rain-out from sea-ice These deposits are characterised by very poorly sorted, faintly laminated muddy sandstones with coarse granules toward their base. Contacts are gradational to sharp. Variations on this style of mass-wasting deposit are rhythmically stacked sequences of pebbly-coarse sandstones representing successive thin debris-flow events. These suggest very high sedimentation rates on an unstable slope in a shallow-water proximal glacimarine environment. Sandy-silty turbidites appear more common in the lower sections of the core, below approximately 141.00 mbsf, although they occur occasionally with the debris flow deposits The turbidites are characterised by inversely to normally graded, well-laminated siltstones with occasional lonestones, and represent a more distal shallow-water glacimarine environment.

Heat flow determinations of ODP Hole 111-504B

Hole 504B in the eastern equatorial Pacific has been the focus of five scientific drilling expeditions since it was first drilled in 1979. During these five legs, a series of temperature logs has been obtained over a time span of almost 8 yr, documenting the geothermal and hydrologic state of the oceanic crust in this region. Immediately following reentry at the onset of ODP Leg 111 operations, a high-resolution temperature probe was lowered into the borehole and a precise record of temperature vs. depth in Hole 504B was recorded down to 1300 mbsf. As was observed during previous legs, the temperature gradient in the upper 400 m was reduced, indicating that downhole flow of cool ocean waters through the casing continued, though at a diminished rate. As subhydrostatic pressures in the upper basement have gradually diminished, the volume of flow has decayed from an estimated 6000-7000 L/hr in late 1979 to about 80 L/hr during Leg 111. At depths below 480 mbsf, a predominantly conductive heat transfer environment enabled the temperature gradient log to be analyzed with respect to lithology on both fine and broad scales. Anomalies in the gradient log in the cased section through the sedimentary column were found to correspond to biostratigraphic age markers and/or sharp changes in sediment composition and texture. Broad variations in temperature gradient within the basement correlated with large-scale porosity trends. Conductive heatflow estimates depict a systematic reduction with depth, ranging from approximately 196 mW/m**2 in the sediments to 120 ± 17 mW/m**2 at 1300 mbsf. Possible causes for this observation were examined from several perspectives, but none was suitably convincing. A fluid instability analysis indicated the likely existence of convection cells within the borehole and substantiated the hypothesis of mixing within the borehole postulated from isotopic and chemical studies of borehole waters. However, such mixing of borehole fluids does not provide an adequate explanation for the heatflow variations, and the disparity between surficial and deep values of heat flow remains unresolved.

Isotope analysis and heat flow measurements of Maria S. Merian cruise MSM21/4 on the western Svalbard margin

Methane hydrate is an ice-like substance that is stable at high-pressure and low temperature in continental margin sediments. Since the discovery of a large number of gas flares at the landward termination of the gas hydrate stability zone off Svalbard, there has been concern that warming bottom waters have started to dissociate large amounts of gas hydrate and that the resulting methane release may possibly accelerate global warming. Here, we can corroborate that hydrates play a role in the observed seepage of gas, but we present evidence that seepage off Svalbard has been ongoing for at least three thousand years and that seasonal fluctuations of 1-2°C in the bottom-water temperature cause periodic gas hydrate formation and dissociation, which focus seepage at the observed sites.