Leaf transmission reduction using moving jaws for dynamic MLC IMRT

The aim of this work is to investigate to what extent it is possible to use the secondary collimator jaws to reduce the transmitted radiation through the multileaf collimator (MLC) during an intensity modulated radiation therapy (IMRT). A method is developed and introduced where the jaws follow the open window of the MLC dynamically (dJAW method). With the aid of three academic cases (Closed MLC, Sliding-gap, and Chair) and two clinical cases (prostate and head and neck) the feasibility of the dJAW method and the influence of this method on the applied dose distributions are investigated. For this purpose the treatment planning system Eclipse and the Research-Toolbox were used as well as measurements within a solid water phantom were performed. The transmitted radiation through the closed MLC leads to an inhomogeneous dose distribution. In this case, the measured dose within a plane perpendicular to the central axis differs up to 40% (referring to the maximum dose within this plane) for 6 and 15 MV. The calculated dose with Eclipse is clearly more homogeneous. For the Sliding-gap case this difference is still up to 9%. Among other things, these differences depend on the depth of the measurement within the solid water phantom and on the application method. In the Chair case, the dose in regions where no dose is desired is locally reduced by up to 50% using the dJAW method instead of the conventional method. The dose inside the chair-shaped region decreased up to 4% if the same number of monitor units (MU) as for the conventional method was applied. The undesired dose in the volume body minus the planning target volume in the clinical cases prostate and head and neck decreased up to 1.8% and 1.5%, while the number of the applied MU increased up to 3.1% and 2.8%, respectively. The new dJAW method has the potential to enhance the optimization of the conventional IMRT to a further step.

Visual acuity of dentists under simulated clinical conditions

OBJECTIVES This study examined the near visual acuity of dentists in relation to age and magnification under simulated clinical conditions. MATERIALS AND METHODS Miniaturized visual tests were performed in posterior teeth of a dental phantom head in a simulated clinical setting (dental chair, operating lamp, dental mirror). The visual acuity of 40 dentists was measured under the following conditions: (1) natural visual acuity, distance of 300 mm; (2) natural visual acuity, free choice of distance; (3) Galilean loupes, magnification of ×2.5; (4) Keplerian loupes, ×4.3; (5) operating microscope, ×4, integrated light; (6) operating microscope, ×6.4, integrated light. RESULTS The visual acuity varied widely between individuals and was significantly lower in the group ≥40 years of age (p < 0.001). Significant differences were found between all tested conditions (p < 0.01). Furthermore, a correlation between visual acuity and age was found for all conditions. The performance with the microscope was better than with loupes even with comparable magnification factors. Some dentists had a better visual acuity without optical aids than others with Galilean loupes. CONCLUSIONS Near visual acuity under simulated clinical conditions varies widely between individuals and decreases throughout life. Visual deficiencies can be compensated for with optical aids. CLINICAL RELEVANCE Newly developed miniaturized vision tests have allowed, in a clinically relevant way, to evaluate the influence of magnification and age on the near visual acuity of dentists.

Ecological validity of virtual reality daily living activities screening for early dementia: longitudinal study

Background: Dementia is a multifaceted disorder that impairs cognitive functions, such as memory, language, and executive functions necessary to plan, organize, and prioritize tasks required for goal-directed behaviors. In most cases, individuals with dementia experience difficulties interacting with physical and social environments. The purpose of this study was to establish ecological validity and initial construct validity of a fire evacuation Virtual Reality Day-Out Task (VR-DOT) environment based on performance profiles as a screening tool for early dementia. Objective: The objectives were (1) to examine the relationships among the performances of 3 groups of participants in the VR-DOT and traditional neuropsychological tests employed to assess executive functions, and (2) to compare the performance of participants with mild Alzheimer’s-type dementia (AD) to those with amnestic single-domain mild cognitive impairment (MCI) and healthy controls in the VR-DOT and traditional neuropsychological tests used to assess executive functions. We hypothesized that the 2 cognitively impaired groups would have distinct performance profiles and show significantly impaired independent functioning in ADL compared to the healthy controls. Methods: The study population included 3 groups: 72 healthy control elderly participants, 65 amnestic MCI participants, and 68 mild AD participants. A natural user interface framework based on a fire evacuation VR-DOT environment was used for assessing physical and cognitive abilities of seniors over 3 years. VR-DOT focuses on the subtle errors and patterns in performing everyday activities and has the advantage of not depending on a subjective rating of an individual person. We further assessed functional capacity by both neuropsychological tests (including measures of attention, memory, working memory, executive functions, language, and depression). We also evaluated performance in finger tapping, grip strength, stride length, gait speed, and chair stands separately and while performing VR-DOTs in order to correlate performance in these measures with VR-DOTs because performance while navigating a virtual environment is a valid and reliable indicator of cognitive decline in elderly persons. Results: The mild AD group was more impaired than the amnestic MCI group, and both were more impaired than healthy controls. The novel VR-DOT functional index correlated strongly with standard cognitive and functional measurements, such as mini-mental state examination (MMSE; rho=0.26, P=.01) and Bristol Activities of Daily Living (ADL) scale scores (rho=0.32, P=.001). Conclusions: Functional impairment is a defining characteristic of predementia and is partly dependent on the degree of cognitive impairment. The novel virtual reality measures of functional ability seem more sensitive to functional impairment than qualitative measures in predementia, thus accurately differentiating from healthy controls. We conclude that VR-DOT is an effective tool for discriminating predementia and mild AD from controls by detecting differences in terms of errors, omissions, and perseverations while measuring ADL functional ability.

Primary care at Swiss universities - current state and perspective

Background There is increasing evidence that a strong primary care is a cornerstone of an efficient health care system. But Switzerland is facing a shortage of primary care physicians (PCPs). This pushed the Federal Council of Switzerland to introduce a multifaceted political programme to strengthen the position of primary care, including its academic role. The aim of this paper is to provide a comprehensive overview of the situation of academic primary care at the five Swiss universities by the end of year 2012. Results Although primary care teaching activities have a long tradition at the five Swiss universities with activities starting in the beginning of the 1980ies; the academic institutes of primary care were only established in recent years (2005 – 2009). Only one of them has an established chair. Human and financial resources vary substantially. At all universities a broad variety of courses and lectures are offered, including teaching in private primary care practices with 1331 PCPs involved. Regarding research, differences among the institutes are tremendous, mainly caused by entirely different human resources and skills. Conclusion So far, the activities of the existing institutes at the Swiss Universities are mainly focused on teaching. However, for a complete academic institutionalization as well as an increased acceptance and attractiveness, more research activities are needed. In addition to an adequate basic funding of research positions, competitive research grants have to be created to establish a specialty-specific research culture.

The significant effect of endometriosis on physical, mental and social wellbeing: results from an international cross-sectional survey.

STUDY QUESTION To what extent do the management of endometriosis and the symptoms that remain after treatment affect the quality of life in women with the disease? SUMMARY ANSWER Many women with endometriosis had impaired quality of life and continued to suffer from endometriosis-associated symptoms even though their endometriosis has been managed in tertiary care centres. WHAT IS KNOWN ALREADY The existing literature indicates that quality of life and work productivity is reduced in women with endometriosis. However, most studies have small sample sizes, are treatment related or examine newly diagnosed patients only. STUDY DESIGN, SIZE, DURATION A cross-sectional questionnaire-based survey among 931 women with endometriosis treated in 12 tertiary care centres in 10 countries. PARTICIPANTS/MATERIALS, SETTING, METHODS Women diagnosed with endometriosis who had at least one contact related to endometriosis-associated symptoms during 2008 with a participating centre were enrolled into the study. The study investigated the effect of endometriosis on education, work and social wellbeing, endometriosis-associated symptoms and health-related quality of life, by using questions obtained from the World Endometriosis Research Foundation (WERF) GSWH instrument (designed and validated for the WERF Global Study on Women's Health) and the Short Form 36 version 2 (SF-36v2). MAIN RESULTS AND THE ROLE OF CHANCE Of 3216 women invited to participate in the study, 1450 (45%) provided informed consent and out of these, 931 (931/3216 = 29%) returned the questionnaires. Endometriosis had affected work in 51% of the women and affected relationships in 50% of the women at some time during their life. Dysmenorrhoea was reported by 59%, dyspareunia by 56% and chronic pelvic pain by 60% of women. Quality of life was decreased in all eight dimensions of the SF-36v2 compared with norm-based scores from a general US population (all P < 0.01). Multivariate regression analysis showed that number of co-morbidities, chronic pain and dyspareunia had an independent negative effect on both the physical and mental component of the SF-36v2. LIMITATIONS, REASONS FOR CAUTION The fact that women were enrolled in tertiary care centres could lead to a possible over-representation of women with moderate-to-severe endometriosis, because the participating centres typically treat more complex and referred cases of endometriosis. The response rate was relatively low. Since there was no Institute Review Board approval to do a non-responder investigation on basic characteristics, some uncertainty remains regarding the representativeness of the investigated population. WIDER IMPLICATIONS OF THE FINDINGS This international multicentre survey represents a large group of women with endometriosis, in all phases of the disease, which increases the generalizability of the data. Women still suffer from frequent symptoms, despite tertiary care management, in particular chronic pain and dyspareunia. As a result their quality of life is significantly decreased. A patient-centred approach with extensive collaboration across disciplines, such as pain specialists, psychologists, sexologists and social workers, may be a valuable strategy to improve the long-term care of women with endometriosis. STUDY FUNDING/COMPETING INTEREST(S) The WERF EndoCost study is funded by the World Endometriosis Research Foundation (WERF) through grants received from Bayer Schering Pharma AG, Takeda Italia Farmaceutici SpA, Pfizer Ltd and the European Society of Human Reproduction and Embryology. The sponsors did not have a role in the design and conduct of the study; collection, management, analysis and interpretation of the data; and preparation, review or approval of the manuscript. L.H. is the chief executive and T.D. was a board member of WERF at the time of funding. T.D. holds the Merck-Serono Chair in Reproductive Medicine and Surgery, and the Ferring Chair in Reproductive Medicine at the Katholieke Universiteit Leuven in Belgium and has served as consultant/research collaborator for Merck-Serono, Schering-Plough, Astellas and Arresto.

An electrophysiological investigation of emotional change: preliminary data

Many psychotherapy researchers agree that emotional change is critical to therapeutic progress. In emotion-focused and Gestalt therapy, one technique to foster emotional change is the empty chair dialogue. Psychotherapy research has yielded ample evidence that this technique helps to alleviate longstanding interpersonal grievances (‘unfinished business’) and facilitates emotional change. Until now, little is known about the neurophysiological correlates of such emotional change. The present study thus aims at adding a further level of analysis to psychotherapy research, and may enrich knowledge about mechanisms of change. Neurophysiological correlates of emotional change were investigated using multi-channel electroencephalography. Individuals experiencing ‘unfinished business’ were guided by experienced therapists to participate in an empty chair dialogue. Event-related brain potentials were recorded before and after the intervention while participants were viewing pictures of the person central to their interpersonal grievance as well as pictures of control persons. Event related potentials are compared regarding topography and overall signal strength. Preliminary results will be discussed regarding neurophysiological mechanisms of action potentially occurring during emotional change.

Space requirement of a prefabricated bar on two interforaminal implants: a prospective clinical study

OBJECTIVES This clinical study measured the dimensional changes of existing lower complete dentures due to the integration of a prefabricated implant bar. Additionally, the impact of this dimensional change on patient satisfaction and oral function was analyzed. METHODS Twenty edentulous patients (10 men/10 women; aged 65.9 ± 11.8 years) received two interforaminal implants. Subsequent to surgery, a chair side adapted, prefabricated bar (SFI Bar(®), C+M, Biel, Switzerland) was inserted, and the matrix was polymerized into the existing lower denture. The change of the denture's lingual dimension was recorded by means of a bicolored, silicone denture duplicate that was sectioned in the oro-vestibular direction in the regions of the symphysis (S) and the implants (I-left, I-right). On the sections, the dimensional increase was measured using a light microscope. Six months after bar insertion, patients answered a standardized questionnaire. RESULTS All dentures exhibited increased lingual volume, more extensively at S than at I (P = 0.001). At S, the median diagonal size of the denture was doubled (+4.33 mm), and at I, the median increase was 50% (I-left/-right = +2.66/+2.62 mm). The original denture size influenced the volume increase (P = 0.024): smaller dentures led to a larger increase. The amount of denture increase did not have negative impact on either self-perceived oral function or patient satisfaction. Approximately, 95% of the patients were satisfied with the treatment results. CONCLUSIONS The lingual size of a lower denture was enlarged by the integration of a prefabricated bar without any negative side effects. Thus, this attachment system is suitable to convert an existing full denture into an implant-supported overdenture.

Time-Efficiency Analysis Comparing Digital and Conventional Workflows for Implant Crowns: A Prospective Clinical Crossover Trial

PURPOSE To compare time-efficiency in the production of implant crowns using a digital workflow versus the conventional pathway. MATERIALS AND METHODS This prospective clinical study used a crossover design that included 20 study participants receiving single-tooth replacements in posterior sites. Each patient received a customized titanium abutment plus a computer-aided design/computer-assisted manufacture (CAD/CAM) zirconia suprastructure (for those in the test group, using digital workflow) and a standardized titanium abutment plus a porcelain-fused-to-metal crown (for those in the control group, using a conventional pathway). The start of the implant prosthetic treatment was established as the baseline. Time-efficiency analysis was defined as the primary outcome, and was measured for every single clinical and laboratory work step in minutes. Statistical analysis was calculated with the Wilcoxon rank sum test. RESULTS All crowns could be provided within two clinical appointments, independent of the manufacturing process. The mean total production time, as the sum of clinical plus laboratory work steps, was significantly different. The mean ± standard deviation (SD) time was 185.4 ± 17.9 minutes for the digital workflow process and 223.0 ± 26.2 minutes for the conventional pathway (P = .0001). Therefore, digital processing for overall treatment was 16% faster. Detailed analysis for the clinical treatment revealed a significantly reduced mean ± SD chair time of 27.3 ± 3.4 minutes for the test group compared with 33.2 ± 4.9 minutes for the control group (P = .0001). Similar results were found for the mean laboratory work time, with a significant decrease of 158.1 ± 17.2 minutes for the test group vs 189.8 ± 25.3 minutes for the control group (P = .0001). CONCLUSION Only a few studies have investigated efficiency parameters of digital workflows compared with conventional pathways in implant dental medicine. This investigation shows that the digital workflow seems to be more time-efficient than the established conventional production pathway for fixed implant-supported crowns. Both clinical chair time and laboratory manufacturing steps could be effectively shortened with the digital process of intraoral scanning plus CAD/CAM technology.

The role of the G20 in WTO governance

Report by Professor Sungjoon Cho, Associate Professor of Law, Chicago-Kent College of Law (Chair), and Charlotte Sieber-Gasser, Doctoral Research Fellow, World Trade Institute, University of Bern, Session 27, WTO Public Forum 2010: The Forces Shapping World Trade, pp.29-33. In the course of the financial crisis, the global geography of power has shifted from G8 to G20. The latter, although representing roughly two thirds of global trade, consists of relatively a small number of global players and is consequently excluding many others from decision-making at the international stage. Nevertheless, the G20 has been successful in its reaction to the financial crisis and became therewith an important new player within the international community. When highlighting how the G20 might interfere with the WTO, the panel voiced concerns over the political legitimacy of the G20, given the limited number of members and the global impact of its decisions. It agreed on the impression that although the G20 intends to extend its debates from the financial sector to world economy in general, it has so far little achieved in this direction, particularly when it comes to moving the Doha agenda forward. It remains, thus, open how the G20 will evolve in the coming few years, and what mandates it will shed or adopt. So far, the G20 has complemented the WTO and international financial institutions in handling the financial crisis. Yet, even if there is little evidence pointing towards a less cooperative role in the future, the desirability of a G20 commitment in WTO trade negotiations has yet to be debated. The panel concluded by providing ideas on how the potential of the G20 might be used to serve global interests even better in the future. In their concluding remarks, the panellists agreed that it remains to be seen whether or not the G20 will further broaden its agenda. Given the ebbing away of the financial crisis there is even the question whether the G20 will remain an important international forum for financial collaboration, or whether it has already served its cause and will eventually disappear from the international stage. The Chair concluded the well attended and lively panel with voicing the hope that the two international bodies – the G20 and the WTO – will work in a positive way together in the future and face the challenges and opportunities in their collaboration to the benefit of everyone.