Reinigung der Vinorin-Synthase aus Zellkulturen von Rauvolfia serpentina

Abstrakt - DeutschThema: Reinigung der Vinorin-Synthase aus Zellkulturen von Rauvolfia serpentina Die Arbeit befaßte sich mit der Reinigung und Charakterisierung des Enzyms Vinorin-Synthase aus Zellkulturen von Rauvolfia serpentina. Dieses Acetyl-Coenzym-A-abhängige Enzym katalysiert im Biosyntheseweg des Alkaloids Ajmalin die Umwandlung von 16-epi-Vellosimin zu Vinorin. Mit Hilfe eines neu entwickelten Enzymaktivitätstests ist eine einfache und schnelle qualitative sowie quantitative Bestimmung der Aktivität der Vinorin-Synthase möglich. Das Molekulargewicht der Vinorin-Synthase wurde durch Größenausschlußchromatographie an Superdex 75 zu 43 kD ermittelt. Das entwickelte Reinigungsschema mit den vier säulenchromatographischen Reinigungsschritten Anionenaustauschchromatographie an SOURCE 30Q, Chromatographie an Hydroxyapatit, Anionenaustauschchromatographie an Mono Q und Chromatofokussierung an Mono P führte zu einer 340fachen Anreicherung der Vinorin-Synthase. Das nach der Reinigung durchgeführten gelelektrophoretischen Untersuchungen ermöglichten keine Zuordnung einer Bande zur Bande der Vinorin-Synthase. Mögliche Ursachen für die Nichtzuordnung einer Bande im SDS-Gel zur Vinorin-Synthase sind in einer möglichen Überlagerung eines Fremdprotein mit der Vinorin-Synthase, eine niedrige Expression der Vinorin-Synthase, die eine deutlich bessere Anreicherung erfordern würde oder der Aufbau des Proteins aus Untereinheiten, in die es während der Behandlung mit SDS zerfällt, gegeben.

Self-assembly of Tetraurea Calix[4]arenes

We have elaborated a multistep strategy to synthesize ABAB-type tetraureas. There are overall nine steps but they involve very simple chemistry. The sequence starts with a 1,3-dialkylation and this is the step in which a difference between distal phenolic units is introduced. The selective ipso-nitration in the next step is based on the difference in reactivity between free phenolic units and alkylated ones. The direct reaction of tetraamino calixarene with tolylisocyanate appears not to be an appropriate method to synthesize 1,3-ditolylurea calixarenes but can be used to get tetraureas of ABBB- and AABB-types in two steps with yields of about 60%. A complete regioselective dimerization was obtained with mono-loop derivatives in which two adjacent urea residues are covalently connected. As predicted/expected the loop prevents the formation of one regioisomer, and only the dimer in which the open-chain residue slips through the loop is formed. To synthesize mono-loop tetraureas 1,2-diBoc protected tetraamino calixarene was acylated with activated di-urethanes under high dilution conditions. Di-loop compounds were synthesized by two different ways. In the reaction of tetraamine and di-urethanes the yield is about 30-40%. The second method is based on the metathesis reaction within a suitable heterodimer. For this strategy, tetraurea derivatives with residues which have terminal double bonds were prepared. The exclusive formation of the heterodimer with tetratosylurea as template is the key point in this strategy. Metathesis followed by hydrogenation give exceptionally good yields (> 80%) of the loop compounds. All the NMR data for di-loop compounds confirm that the loops prevent the interaction of the urea residues which are connected and thus, as expected, the di-loop derivatives do not form homodimers. The heterodimer between di-loop compounds and tetratolylurea (open-chain tetraureas) was the only species observed for a 1:1 mixture in benzene or chloroform. The rational synthesis of bis-[2]catenanes was a consequence of the selective formation of one regioisomer of mono-loop derivatives and the exclusive formation of heterodimers by di-loop derivatives. The formation of interlocking-ring in the synthesis of bis-[2]catenanes is an additional evidence that one open-chain residue slips through the loop in mono- or di-loop derivatives. Exceptionally good yields in the synthesis of bis-[2]catenanes are due to the high preorganization in the dimer which undergoes the metathesis. This preorganization decreases the number of the wrong connections and favors the new connections to be formed. Although the procedure for working up the reaction mixture should be still improved, these results are promising. A C2-symmetrical bis-[2]catenane was successfully resolved by column chromatography using a chiral stationary phase. Thus it should be possible to separate a larger amount to obtain pure enantiomers for further studies.

Die Vielseitigkeit von Carbazol in pi-konjugierten Materialien: Makrozyklen, Doppelstrang-Strukturen und Donor-Akzeptor-Copolymere

In dieser Arbeit wurden die vielfältigen Anwendungsmöglichkeiten von Carbazol-reichen Verbindungen in unterschiedlichen Architekturen von pi-konjugierten Materialien untersucht. Die Darstellung der Makrozyklen in Kapitel 1 erfolgte über eine templatunterstützte Synthese, da die ausschließlich über ihre para-Position verknüpften Einheiten einen Zugang über ihre Geometrie nicht erlaubten. Cyclododeca-2,7-fluoren wurde als zyklische Modellverbindung für die zahlreichen bekannten linearen Oligo- und Polyfluorene dargestellt, um den Einfluss der Ringstruktur auf die optischen Eigenschaften dieser blau emittierenden Verbindungen zu untersuchen. Motiviert von den geringen Ausbeuten bei der Zyklisierung des Rings unter Yamamoto-Bedingungen wurde nach einer alternativen Kupplungsreaktion gesucht, die den Zugang zu größeren Substanzmengen erlaubt. Die Einführung von terminalen Ethinylgruppen an die zu verknüpfenden Bausteine erlaubte über die Glaser-Eglinton-Reaktion nicht nur eine Verbesserung der Reaktionsausbeute um den Faktor 10, sondern gleichzeitig auch die Erweiterung des Durchmessers auf rund 5 nm. Demonstriert wurde dies anhand der Darstellung von Cyclo[tetrakis(2,7-diethinyltriscarbazol)] und Cyclo[tetrakis(2,7-diethinyltrisfluoren)].rnDer zweite Abschnitt der Dissertation befasste sich mit ausgedehnten zweidimensionalen Strukturen, zu denen auch mehrsträngige Polymere zählen. Für die Darstellung eines Doppelstrang-Polymers mit hoher Periodizität in den beiden in regelmäßigen Abständen verknüpften Strängen wurde ein neues Konzept entwickelt, dass den Zugang zu solchen Verbindungen erlauben sollte. Dieses basierte auf einem vierfach funktionalisierten Carbazol-Makromonomer. Die Polymerisationen wurden in zwei Schritten über Glaser-Eglinton-Reaktionen durchgeführt. Um unkontrollierte Kupplungen zu vermeiden, wurden zwei der vier reaktiven Positionen am Monomer zunächst über Schutzgruppen maskiert und nach der ersten Polymerisation wieder aktiviert. Neben diesem Ansatz über oxidative Ethinylkupplungen wurde auch eine Organometall-Variante mit einem Platin-Komplex im Polymerrückgrat vorgestellt. rnIm dritten Kapitel wurde die Darstellung von Donor-Akzeptor-Polymeren mit niedriger Bandlücke für den Einsatz in organischen Solarzellen besprochen. Im Gegensatz zu den bisherigen Ansätzen in der Literatur wurden hier ganz gezielt Donor- und Akzeptor-Einheiten mit einer Länge von mindestens 1,5 nm synthetisiert und kombiniert, um zu untersuchen, welche Auswirkungen der Einsatz solcher Makromonomere auf die Eigenschaften der Materialien hat. Dabei bestand der Akzeptor-Baustein in drei Polymeren aus Bis[2,7-di-(4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl)-9,9,18,18-tetraoctylindeno[1,2-b]-yl]-indeno[1,2-b]fluoren-12,15-dion, während die Donor-Stärke durch den Übergang von einem reinen leiterverbrückten Carbazol-Monomer über eine gemischte Carbazol-Thiophen-Einheit hin zu einem reinen Thiophen-Precursor variiert wurde. Dabei zeigte das Polymer mit Thiophen als Donor den höchsten Zellwirkungsgrad von 0,41 %.rn

Development of a comprehensive on-line multidimensional high performance column liquid chromatography system for protein and peptide mapping with integrated size selective sample fractionation

Aufbau einer kontinuierlichen, mehrdimensionalen Hochleistungs-flüssigchromatographie-Anlage für die Trennung von Proteinen und Peptiden mit integrierter größenselektiver ProbenfraktionierungEs wurde eine mehrdimensionale HPLC-Trennmethode für Proteine und Peptide mit einem Molekulargewicht von <15 kDa entwickelt.Im ersten Schritt werden die Zielanalyte von höhermolekularen sowie nicht ionischen Bestandteilen mit Hilfe von 'Restricted Access Materialien' (RAM) mit Ionenaustauscher-Funktionalität getrennt. Anschließend werden die Proteine auf einer analytischen Ionenaustauscher-Säule sowie auf Reversed-Phase-Säulen getrennt. Zur Vermeidung von Probenverlusten wurde ein kontinuierlich arbeitendes, voll automatisiertes System auf Basis unterschiedlicher Trenngeschwindigkeiten und vier parallelen RP-Säulen aufgebaut.Es werden jeweils zwei RP-Säulen gleichzeitig, jedoch mit zeitlich versetztem Beginn eluiert, um durch flache Gradienten ausreichende Trennleistungen zu erhalten. Während die dritte Säule regeneriert wird, erfolgt das Beladen der vierte Säule durch Anreicherung der Proteine und Peptide am Säulenkopf. Während der Gesamtanalysenzeit von 96 Minuten werden in Intervallen von 4 Minuten Fraktionen aus der 1. Dimension auf die RP-Säulen überführt und innerhalb von 8 Minuten getrennt, wobei 24 RP-Chromatogramme resultieren.Als Testsubstanzen wurden u.a. Standardproteine, Proteine und Peptide aus humanem Hämofiltrat sowie aus Lungenfibroblast-Zellkulturüberständen eingesetzt. Weiterhin wurden Fraktionen gesammelt und mittels MALDI-TOF Massenspektrometrie untersucht. Bei einer Injektion wurden in den 24 RP-Chromatogrammen mehr als 1000 Peaks aufgelöst. Der theoretische Wert der Peakkapazität liegt bei ungefähr 3000.

Pore structure and column efficiency of silica monoliths in high performance liquid chromatography (HPLC)

Five different methods were critically examined to characterize the pore structure of the silica monoliths. The mesopore characterization was performed using: a) the classical BJH method of nitrogen sorption data, which showed overestimated values in the mesopore distribution and was improved by using the NLDFT method, b) the ISEC method implementing the PPM and PNM models, which were especially developed for monolithic silicas, that contrary to the particulate supports, demonstrate the two inflection points in the ISEC curve, enabling the calculation of pore connectivity, a measure for the mass transfer kinetics in the mesopore network, c) the mercury porosimetry using a new recommended mercury contact angle values. rnThe results of the characterization of mesopores of monolithic silica columns by the three methods indicated that all methods were useful with respect to the pore size distribution by volume, but only the ISEC method with implemented PPM and PNM models gave the average pore size and distribution based on the number average and the pore connectivity values.rnThe characterization of the flow-through pore was performed by two different methods: a) the mercury porosimetry, which was used not only for average flow-through pore value estimation, but also the assessment of entrapment. It was found that the mass transfer from the flow-through pores to mesopores was not hindered in case of small sized flow-through pores with a narrow distribution, b) the liquid penetration where the average flow-through pore values were obtained via existing equations and improved by the additional methods developed according to Hagen-Poiseuille rules. The result was that not the flow-through pore size influences the column bock pressure, but the surface area to volume ratio of silica skeleton is most decisive. Thus the monolith with lowest ratio values will be the most permeable. rnThe flow-through pore characterization results obtained by mercury porosimetry and liquid permeability were compared with the ones from imaging and image analysis. All named methods enable a reliable characterization of the flow-through pore diameters for the monolithic silica columns, but special care should be taken about the chosen theoretical model.rnThe measured pore characterization parameters were then linked with the mass transfer properties of monolithic silica columns. As indicated by the ISEC results, no restrictions in mass transfer resistance were noticed in mesopores due to their high connectivity. The mercury porosimetry results also gave evidence that no restrictions occur for mass transfer from flow-through pores to mesopores in the small scaled silica monoliths with narrow distribution. rnThe prediction of the optimum regimes of the pore structural parameters for the given target parameters in HPLC separations was performed. It was found that a low mass transfer resistance in the mesopore volume is achieved when the nominal diameter of the number average size distribution of the mesopores is appr. an order of magnitude larger that the molecular radius of the analyte. The effective diffusion coefficient of an analyte molecule in the mesopore volume is strongly dependent on the value of the nominal pore diameter of the number averaged pore size distribution. The mesopore size has to be adapted to the molecular size of the analyte, in particular for peptides and proteins. rnThe study on flow-through pores of silica monoliths demonstrated that the surface to volume of the skeletons ratio and external porosity are decisive for the column efficiency. The latter is independent from the flow-through pore diameter. The flow-through pore characteristics by direct and indirect approaches were assessed and theoretical column efficiency curves were derived. The study showed that next to the surface to volume ratio, the total porosity and its distribution of the flow-through pores and mesopores have a substantial effect on the column plate number, especially as the extent of adsorption increases. The column efficiency is increasing with decreasing flow through pore diameter, decreasing with external porosity, and increasing with total porosity. Though this tendency has a limit due to heterogeneity of the studied monolithic samples. We found that the maximum efficiency of the studied monolithic research columns could be reached at a skeleton diameter of ~ 0.5 µm. Furthermore when the intention is to maximize the column efficiency, more homogeneous monoliths should be prepared.rn

The release of zinc and lead from mine tailings

Mining and processing of metal ores are important causes of soil and groundwater contamination in many regions worldwide. Metal contaminations are a serious risk for the environment and human health. The assessment of metal contaminations in the soil is therefore an important task. A common approach to assess the environmental risk emanating from inorganic contaminations to soil and groundwater is the use of batch or column leaching tests. In this regard, the suitability of leaching tests is a controversial issue. In the first part of this work the applicability and comparability of common leaching tests in the scope of groundwater risk assessment of inorganic contamination is reviewed and critically discussed. Soil water sampling methods (the suction cup method and centrifugation) are addressed as an alternative to leaching tests. Reasons for limitations of the comparability of leaching test results are exposed and recommendations are given for the expedient application of leaching tests for groundwater risk assessment. Leaching tests are usually carried out in open contact with the atmosphere disregarding possible changes of redox conditions. This can affect the original metal speciation and distribution, particularly when anoxic samples are investigated. The influence of sample storage on leaching test results of sulfide bearing anoxic material from a former flotation dump is investigated in a long-term study. Since the oxidation of the sulfide-bearing samples leads to a significant overestimation of metal release, a feasible modification for the conduction of common leaching tests for anoxic material is proposed, where oxidation is prevented efficiently. A comparison of leaching test results to soil water analyzes have shown that the modified saturation soil extraction (SSE) is found to be the only of the tested leaching procedures, which can be recommended for the assessment of current soil water concentrations at anoxic sites if direct investigation of the soil water is impossible due to technical reasons. The vertical distribution and speciation of Zn and Pb in the flotation residues as well as metal concentrations in soil water and plants were investigated to evaluate the environmental risk arising from this site due to the release of metals. The variations in pH and inorganic C content show an acidification of the topsoil with pH values down to 5.5 in the soil and a soil water pH of 6 in 1 m depth. This is due to the oxidation of sulfides and depletion in carbonates. In the anoxic subsoil pH conditions are still neutral and soil water collected with suction cups is in equilibrium with carbonate minerals. Results from extended x-ray absorption fine-structure (EXAFS) spectroscopy confirm that Zn is mainly bound in sphalerite in the subsoil and weathering reactions lead to a redistribution of Zn in the topsoil. A loss of 35% Zn and S from the topsoil compared to the parent material with 10 g/kg Zn has been observed. 13% of total Zn in the topsoil can be regarded as mobile or easily mobilizable according to sequential chemical extractions (SCE). Zn concentrations of 10 mg/L were found in the soil water, where pH is acidic. Electron supply and the buffer capacity of the soil were identified as main factors controlling Zn mobility and release to the groundwater. Variable Pb concentrations up to 30 µg/L were observed in the soil water. In contrast to Zn, Pb is enriched in the mobile fraction of the oxidized topsoil by a factor of 2 compared to the subsoil with 2 g/kg Pb. 80% of the cation exchange capacity in the topsoil is occupied by Pb. Therefore, plant uptake and bioavailability are of major concern. If the site is not prevented from proceeding acidification in the future, a significant release of Zn, S, and Pb to the groundwater has to be expected. Results from this study show that the assessment of metal release especially from sulfide bearing anoxic material requires an extensive comprehension of leaching mechanisms on the one hand and on weathering processes, which influence the speciation and the mobility of metals, on the other hand. Processes, which may change redox and pH conditions in the future, have to be addressed to enable sound decisions for soil and groundwater protection and remediation.

Oxygen-containing polycyclic aromatic hydrocarbons (OPAHs) and their parent-PAHs in soil

In spite of the higher toxicity of oxygen-containing polycyclic aromatic hydrocarbons (OPAHs) than of their parent-PAHs, there are only a few studies of the concentrations, composition pattern, sources and fate of OPAHs in soil, the presumably major environmental sink of OPAHs. This is related to the fact that there are only few available methods to measure OPAHs together with PAHs in soil. rnThe objectives of my thesis were to (i) develop a GC/MS-based method to measure OPAHs and their parent-PAHs in soils of different properties and pollution levels, (ii) apply the method to soils from Uzbekistan and Slovakia and (iii) investigate into the fate of OPAHs, particularly their vertical transport in soilrnI optimized and fully evaluated an analytical method based on pressurized liquid extraction, silica gel column chromatographic fractionation of extracted compounds into alkyl-/parent-PAH and OPAH fractions, silylation of hydroxyl-/carboxyl-OPAHs with N,O-bis(trimethylsilyl)trifluoracetamide and GC/MS quantification of the target compounds. The method was targeted at 34 alkyl-/parent-PAHs, 7 carbonyl-OPAHs and 19 hydroxyl-/carboxyl-OPAHs. I applied the method to 11 soils from each of the Angren industrial region (which hosts a coal mine, power plant, rubber factory and gold refinery) in Uzbekistan and in the city of Bratislava, the densely populated capital of Slovakia.rnRecoveries of five carbonyl-OPAHs in spike experiments ranged between 78-97% (relative standard deviation, RSD, 5-12%), while 1,2-acenaphthenequinone and 1,4-naphtho-quinone had recoveries between 34-44%% (RSD, 19-28%). Five spiked hydroxyl-/carboxyl-OPAHs showed recoveries between 36-70% (RSD, 13-46%), while others showed recoveries &amp;amp;lt;10% or were completely lost. With the optimized method, I determined, on average, 103% of the alkyl-/parent-PAH concentrations in a certified reference material.rnThe ∑OPAHs concentrations in surface soil ranged 62-2692 ng g-1 and those of ∑alkyl-/parent-PAHs was 842-244870 ng g-1. The carbonyl-OPAHs had higher concentrations than the hydroxyl-/carboxyl-OPAHs. The most abundant carbonyl-OPAHs were consistently 9-fluorenone (9-FLO), 9,10-anthraquinone (9,10-ANQ), 1-indanone (1-INDA) and benzo[a]anthracene-7,12-dione (7,12-B(A)A) and the most abundant hydroxyl-/carboxyl-OPAH was 2-hydroxybenzaldehyde. The concentrations of carbonyl-OPAHs were frequently higher than those of their parent-PAHs (e.g., 9-FLO/fluorene &amp;amp;gt;100 near a rubber factory in Angren). The concentrations of OPAHs like those of their alkyl-/parent-PAHs were higher at locations closer to point sources and the OPAH and PAH concentrations were correlated suggesting that both compound classes originated from the same sources. Only for 1-INDA and 2-biphenylcarboxaldehyde sources other than combustion seemed to dominate. Like those of the alkyl-/parent-PAHs, OPAH concentrations were higher in topsoils than subsoils. Evidence of higher mobility of OPAHs than their parent-PAHs was provided by greater subsoil:topsoil concentration ratios of carbonyl-OPAHs (0.41-0.82) than their parent-PAHs (0.41-0.63) in Uzbekistan. This was further backed by the consistently higher contribution of more soluble 9-FLO and 1-INDA to the ∑carbonyl-OPAHs in subsoil than topsoil at the expense of 9,10-ANQ, 7,12-B(A)A and higher OPAH/parent-PAH concentration ratios in subsoil than topsoil in Bratislava.rnWith this thesis, I contribute a suitable method to determine a large number of OPAHs and PAHs in soil. My results demonstrate that carbonyl-OPAHs are more abundant than hydroxyl-/carboxyl-OPAHs and OPAH concentrations are frequently higher than parent-PAH concentrations. Furthermore, there are indications that OPAHs are more mobile in soil than PAHs. This calls for appropriate legal regulation of OPAH concentrations in soil.