5 resultados para rock powder
em ArchiMeD - Elektronische Publikationen der Universität Mainz - Alemanha
Resumo:
This PhD thesis concerns geochemical constraints on recycling and partial melting of Archean continental crust. A natural example of such processes was found in the Iisalmi area of Central Finland. The rocks from this area are Middle to Late Archean in age and experienced metamorphism and partial melting between 2.7-2.63 Ga. The work is based on extensive field work. It is furthermore founded on bulk rock geochemical data as well as in-situ analyses of minerals. All geochemical data were obtained at the Institute of Geosciences, University of Mainz using X-ray fluorescence, solution ICP-MS and laser ablation-ICP-MS for bulk rock geochemical analyses. Mineral analyses were accomplished by electron microprobe and laser ablation ICP-MS. Fluid inclusions were studied by microscope on a heating-freezing-stage at the Geoscience Center, University Göttingen. Part I focuses on the development of a new analytical method for bulk rock trace element determination by laser ablation-ICP-MS using homogeneous glasses fused from rock powder on an Iridium strip heater. This method is applicable for mafic rock samples whose melts have low viscosities and homogenize quickly at temperatures of ~1200°C. Highly viscous melts of felsic samples prevent melting and homogenization at comparable temperatures. Fusion of felsic samples can be enabled by addition of MgO to the rock powder and adjustment of melting temperature and melting duration to the rock composition. Advantages of the fusion method are low detection limits compared to XRF analyses and avoidance of wet-chemical processing and use of strong acids as in solution ICP-MS as well as smaller sample volumes compared to the other methods. Part II of the thesis uses bulk rock geochemical data and results from fluid inclusion studies for discrimination of melting processes observed in different rock types. Fluid inclusion studies demonstrate a major change in fluid composition from CO2-dominated fluids in granulites to aqueous fluids in TTG gneisses and amphibolites. Partial melts were generated in the dry, CO2-rich environment by dehydration melting reactions of amphibole which in addition to tonalitic melts produced the anhydrous mineral assemblages of granulites (grt + cpx + pl ± amph or opx + cpx + pl + amph). Trace element modeling showed that mafic granulites are residues of 10-30 % melt extraction from amphibolitic precursor rocks. The maximum degree of melting in intermediate granulites was ~10 % as inferred from modal abundances of amphibole, clinopyroxene and orthopyroxene. Carbonic inclusions are absent in upper-amphibolite facies migmatites whereas aqueous inclusion with up to 20 wt% NaCl are abundant. This suggests that melting within TTG gneisses and amphibolites took place in the presence of an aqueous fluid phase that enabled melting at the wet solidus at temperatures of 700-750°C. The strong disruption of pre-metamorphic structures in some outcrops suggests that the maximum amount of melt in TTG gneisses was ~25 vol%. The presence of leucosomes in all rock types is taken as the principle evidence for melt formation. However, mineralogical appearance as well as major and trace element composition of many leucosomes imply that leucosomes seldom represent frozen in-situ melts. They are better considered as remnants of the melt channel network, e.g. ways on which melts escaped from the system. Part III of the thesis describes how analyses of minerals from a specific rock type (granulite) can be used to determine partition coefficients between different minerals and between minerals and melt suitable for lower crustal conditions. The trace element analyses by laser ablation-ICP-MS show coherent distribution among the principal mineral phases independent of rock composition. REE contents in amphibole are about 3 times higher than REE contents in clinopyroxene from the same sample. This consistency has to be taken into consideration in models of lower crustal melting where amphibole is replaced by clinopyroxene in the course of melting. A lack of equilibrium is observed between matrix clinopyroxene / amphibole and garnet porphyroblasts which suggests a late stage growth of garnet and slow diffusion and equilibration of the REE during metamorphism. The data provide a first set of distribution coefficients of the transition metals (Sc, V, Cr, Ni) in the lower crust. In addition, analyses of ilmenite and apatite demonstrate the strong influence of accessory phases on trace element distribution. Apatite contains high amounts of REE and Sr while ilmenite incorporates about 20-30 times higher amounts of Nb and Ta than amphibole. Furthermore, trace element mineral analyses provide evidence for magmatic processes such as melt depletion, melt segregation, accumulation and fractionation as well as metasomatism having operated in this high-grade anatectic area.
Resumo:
Within this work, a particle-polymer surface system is studied with respect to the particle-surface interactions. The latter are governed by micromechanics and are an important aspect for a wide range of industrial applications. Here, a new methodology is developed for understanding the adhesion process and measure the relevant forces, based on the quartz crystal microbalance, QCM. rnThe potential of the QCM technique for studying particle-surface interactions and reflect the adhesion process is evaluated by carrying out experiments with a custom-made setup, consisting of the QCM with a 160 nm thick film of polystyrene (PS) spin-coated onto the quartz and of glass particles, of different diameters (5-20µm), deposited onto the polymer surface. Shifts in the QCM resonance frequency are monitored as a function of the oscillation amplitude. The induced frequency shifts of the 3rd overtone are found to decrease or increase, depending on the particle-surface coupling type and the applied oscillation (frequency and amplitude). For strong coupling the 3rd harmonic decreased, corresponding to an “added mass” on the quartz surface. However, positive frequency shifts are observed in some cases and are attributed to weak-coupling between particle and surface. Higher overtones, i.e. the 5th and 7th, were utilized in order to derive additional information about the interactions taking place. For small particles, the shift for specific overtones can increase after annealing, while for large particle diameters annealing causes a negative frequency shift. The lower overtones correspond to a generally strong-coupling regime with mainly negative frequency shifts observed, while the 7th appears to be sensitive to the contact break-down and the recorded shifts are positive.rnDuring oscillation, the motion of the particles and the induced frequency shift of the QCM are governed by a balance between inertial forces and contact forces. The adherence of the particles can be increased by annealing the PS film at 150°C, which led to the formation of a PS meniscus. For the interpretation, the Hertz, Johnson-Kendall-Roberts, Derjaguin-Müller-Toporov and the Mindlin theory of partial slip are considered. The Mindlin approach is utilized to describe partial slip. When partial slip takes place induced by an oscillating load, a part of the contact ruptures. This results in a decrease of the effective contact stiffness. Additionally, there are long-term memory effects due to the consolidation which along with the QCM vibrations induce a coupling increase. However, the latter can also break the contact, lead to detachment and even surface damage and deformation due to inertia. For strong coupling the particles appear to move with the vibrations and simply act as added effective mass leading to a decrease of the resonance frequency, in agreement with the Sauerbrey equation that is commonly used to calculate the added mass on a QCM). When the system enters the weak-coupling regime the particles are not able to follow the fast movement of the QCM surface. Hence, they effectively act as adding a “spring” with an additional coupling constant and increase the resonance frequency. The frequency shift, however, is not a unique function of the coupling constant. Furthermore, the critical oscillation amplitude is determined, above which particle detach. No movement is detected at much lower amplitudes, while for intermediate values, lateral particle displacement is observed. rnIn order to validate the QCM results and study the particle effects on the surface, atomic force microscopy, AFM, is additionally utilized, to image surfaces and measure surface forces. By studying the surface of the polymer film after excitation and particle removal, AFM imaging helped in detecting three different meniscus types for the contact area: the “full contact”, the “asymmetrical” and a third one including a “homocentric smaller meniscus”. The different meniscus forms result in varying bond intensity between particles and polymer film, which could explain the deviation between number of particles per surface area measured by imaging and the values provided by the QCM - frequency shift analysis. The asymmetric and the homocentric contact types are suggested to be responsible for the positive frequency shifts observed for all three measured overtones, i.e. for the weak-coupling regime, while the “full contact” type resulted in a negative frequency shift, by effectively contributing to the mass increase of the quartz..rnThe interplay between inertia and contact forces for the particle-surface system leads to strong- or weak-coupling, with the particle affecting in three mentioned ways the polymer surface. This is manifested in the frequency shifts of the QCM system harmonics which are used to differentiate between the two interaction types and reflect the overall state of adhesion for particles of different size.rn
Resumo:
Die vorliegende Arbeit wurde im Rahmen eines Stipendiums des interdisziplinärenrnGraduiertenkollegs 826 „Spurenanalytik von Elementspezies: Methodenentwicklung und Anwendungen“, gefördert durch die Deutsche Forschungsgemeinschaft (DFG) und das Land Rheinland-Pfalz, angefertigt. Dabei sollten neue Erkenntnisse über die Wechselwirkung zwischen Neptunium und natürlichem Tongestein mit Hinblick auf die Endlagerung wärmeentwickelnder radioaktiver Abfälle in einem geologischen Tiefenlager gewonnen werden. Auf Grund seiner langen Halbwertszeit von mehr als zwei Millionen Jahren wird Np-237 einen signifikanten Anteil an der Radiotoxizität dieser Abfälle nach Lagerzeiten von mehr als 1000 Jahren haben. Np tritt in Lösung unter umweltrelevanten Bedingungen in den Oxidationsstufen +IV und +V auf. Auf Grund der guten Löslichkeit und daher höheren Mobilität ist Np(V) als die gefährlichere Spezies einzustufen. In den Migrationsstudien wurdernOpalinuston (OPA) aus Mont Terri, Schweiz, als natürliches Referenzmaterial verwendet. Der Fokus dieser Arbeit lag dabei auf der Speziation von Np an der Mineraloberfläche mittels synchrotronbasierter Röntgenabsorptionsspektroskopie (EXAFS/XANES).rnDie Wechselwirkung zwischen Np(V) und OPA wurde zunächst in Batch- und Diffusionsexperimenten in Abhängigkeit verschiedener experimenteller Parameter (u.a. pH, Temperatur, Hintergrundelektrolyt, Einfluss von Huminsäure, Konkurrenz mit U(VI), aerobe/anaerobe Bedingungen) untersucht. Die Untersuchung der Np-Speziation erfolgt zum einen an Pulverproben aus Batch-Experimenten unter aeroben und anaeroben Bedingungen, welche mittels EXAFS-Spektroskopie untersucht wurden. Zum anderen wurden ortsaufgelöste μ-XANES-Messungen an Np-Anreicherungen auf OPA-Dünnschliffen und in Diffusionsproben durchgeführt. Durch Kombination der Spektroskopie mit μ-Rötngenfluoreszenzmapping (XRF) und μ-Röntgenbeugung (XRD) konnten zudem Erkenntnisse über die Elementverteilung von Np und anderen im Opalinuston enthaltenen Elementen sowie über kristalline Mineralphasen im Umfeld von Bereichen erhöhter Np-Konzentration erhalten werden.rnSowohl Sorptionsexperimente als auch die spektroskopischen Untersuchungen zeigten eine teilweise Reduktion von Np(V) zu Np(IV) bei der Wechselwirkung mit OPA. Dabei konnte Pyrit als eine der redoxaktiven Phasen identifiziert werden. In diesem Zusammenhang ist die Bildung schwerlöslicher Np(IV)-Spezies mit Hinblick auf die Endlagerung positiv zu bewerten.
Resumo:
Die vorliegende Arbeit wurde im Rahmen des BMWi-Verbundprojektes Wechselwirkung und Transport von Aktiniden im natürlichen Tongestein unter Berücksichtigung von Huminstoffen und Tonorganika – Wechselwirkung von Neptunium und Plutonium mit natürlichem Tongestein“ durchgeführt. Um die langfristige Sicherheit der nuklearen Endlager beurteilen zu können, muss eine mögliche Migration der radiotoxischen Abfälle in die Umwelt betrachtet werden. Wegen seiner langen Halbwertszeit (24000 a) leistet Pu-239 einen wesentlichen Beitrag zur Radiotoxizität abgebrannter Kernbrennstoffe in einem Endlager. Das redox-sensitive Pu tritt in Lösung unter umweltrelevanten Bedingungen in den Oxidationsstufen +III bis +VI auf und kann nebeneinander in bis zu vier Oxidationsstufen vorliegen. Tonsteinformationen werden als mögliches Wirtsgestein für Endlager hoch-radioaktiver Abfälle betrachtet. Deshalb sind ausführliche Informationen zur Mobilisierung und Immobilisierung des Pu durch/in das Grundwasser aus einem Endlager von besonderer Bedeutung. In dieser Arbeit wurden neue Erkenntnisse über die Wechselwirkung zwischen Pu und dem natürlichen Tongestein Opalinuston (OPA, Mont Terri, Schweiz) mit Hinblick auf die Endlagerung wärmeentwickelnder radioaktiver Abfälle in einem geologischen Tiefenlager gewonnen.rnDer Fokus der Arbeit lag dabei auf der Bestimmung der Speziation von Pu an der Mineraloberfläche nach Sorptions- und Diffusionsprozessen mittels verschiedener synchrotronbasierter Methoden (µ-XRF, µ-XANES/EXAFS, µ-XRD, XANES/EXAFS). rnDie Wechselwirkung zwischen Pu und OPA wurde zunächst in Batch- und Diffusionsexperimenten in Abhängigkeit verschiedener experimenteller Parameter (u.a. pH, Pu-Oxidationsstufe) untersucht. In Sorptionsexperimenten konnte gezeigt werden, dass einige Parameter (z.B. Temperatur, Huminsäure) einen deutlichen Einfluss auf die Sorption von Pu haben.rnDie Speziationsuntersuchungen wurden zum einen an Pulverproben aus Batchexperimenten und zum anderen an OPA-Dünnschliffen bzw. Diffusionsproben in Abhängigkeit verschiedener experimenteller Parameter durchgeführt. Die EXAFS-Messungen an der Pu LIII-Kante der Pulverproben ergaben, dass eine innersphäriche Sorption von Pu(IV) an Tongestein unabhängig von dem Ausgangsoxidationszustand des Plutoniums in Lösung stattgefunden hat. Durch die Kombination der ortsaufgelösten Methoden wurde erstmalig mittels μ-XRF die Verteilung von Pu und anderen in OPA enthaltenen Elementen bestimmt. µ-XANES-Spektren an Pu-Anreicherungen auf OPA-Dünnschliffen und in Diffusionsproben bestätigen, dass das weniger mobile Pu(IV) die dominierende Spezies nach den Sorptions- und Diffusionsprozessen ist. Darüber hinaus wurde zum ersten Mal ein Diffusionsprofil von Pu in OPA mittels µ-XRF gemessen. Die Speziationsuntersuchungen mittels μ-XANES zeigten, dass das eingesetzte Pu(V) entlang seines Diffusionspfades zunehmend zu Pu(IV) reduziert wird. Mit µ-XRD wurde Illit als dominierende Umgebung, in der Pu angereichert wurde, identifiziert und Siderit als eine redoxaktive Phase auftreten kann. Die Ergebnisse dieser Arbeit zeigen, dass die Sicherheit von OPA als Wirtsgestein eines Endlagers hoch-radioaktiver Abfälle positiv zu bewerten ist. rn
Resumo:
Fine powders commonly have poor flowability and dispersibility due to interparticle adhesion that leads to formation of agglomerates. Knowing about adhesion in particle collectives is indispensable to gain a deeper fundamental understanding of particle behavior in powders. Especially in pharmaceutical industry a control of adhesion forces in powders is mandatory to improve the performance of inhalation products. Typically the size of inhalable particles is in the range of 1 - 5 µm. In this thesis, a new method was developed to measure adhesion forces of particles as an alternative to the established colloidal probe and centrifuge technique, which are both experimentally demanding, time consuming and of limited practical applicability. The new method is based on detachment of individual particles from a surface due to their inertia. The required acceleration in the order of 500 000 g is provided by a Hopkinson bar shock excitation system and measured via laser vibrometry. Particle detachment events are detected on-line by optical video microscopy. Subsequent automated data evaluation allows obtaining a statistical distribution of particle adhesion forces. To validate the new method, adhesion forces for ensembles of single polystyrene and silica microspheres on a polystyrene coated steel surface were measured under ambient conditions. It was possible to investigate more than 150 individual particles in one experiment and obtain adhesion values of particles in a diameter range of 3 - 13 µm. This enables a statistical evaluation while measuring effort and time are considerably lower compared to the established techniques. Measured adhesion forces of smaller particles agreed well with values from colloidal probe measurements and theoretical predictions. However, for the larger particles a stronger increase of adhesion with diameter was observed. This discrepancy might be induced by surface roughness and heterogeneity that influence small and large particles differently. By measuring adhesion forces of corrugated dextran particles with sizes down to 2 µm it was demonstrated that the Hopkinson bar method can be used to characterize more complex sample systems as well. Thus, the new device will be applicable to study a broad variety of different particle-surface combinations on a routine basis, including strongly cohesive powders like pharmaceutical drugs for inhalation.