Mechanics and dynamics of liposomes and cells studied by QCM and ECIS

The present thesis introduces a novel sensitive technique based on TSM resonators that provides quantitative information about the dynamic properties of biological cells and artificial lipid systems. In order to support and complement results obtained by this method supplementary measurements based on ECIS technique were carried out. The first part (chapters 3 and 4) deals with artificial lipid systems. In chapter 3 ECIS measurements were used to monitor the adsorption of giant unilamellar vesicles as well as their thermal fluctuations. From dynamic Monte Carlo Simulations the rate constant of vesicle adsorption was determined. Furthermore, analysis of fluctuation measurements reveals Brownian motion reflecting membrane undulations of the adherent liposomes. In chapter 4 QCM-based fluctuation measurements were applied to quantify nanoscopically small deformations of giant unilamellar vesicles with an external electrical field applied simultaneously. The response of liposomes to an external voltage with shape changes was monitored as a function of cholesterol content and adhesion force. In the second part (chapters 5 - 8) attention was given to cell motility. It was shown for the first time, that QCM can be applied to monitor the dynamics of living adherent cells in real time. QCM turned out to be a highly sensitive tool to detect the vertical motility of adherent cells with a time resolution in the millisecond regime. The response of cells to environmental changes such as temperature or osmotic stress could be quantified. Furthermore, the impact of cytochalasin D (inhibits actin polymerization) and taxol (facilitate polymerization of microtubules) as well as nocodazole (depolymerizes microtubules) on the dynamic properties of cells was scrutinized. Each drug provoked a significant reduction of the monitored cell shape fluctuations as expected from their biochemical potential. However, not only the abolition of fluctuations was observed but also an increase of motility due to integrin-induced transmembrane signals. These signals were activated by peptides containing the RGD sequence, which is known to be an integrin recognition motif. Ultimately, two pancreatic carcinoma cell lines, derived from the same original tumor, but known to possess different metastatic potential were studied. Different dynamic behavior of the two cell lines was observed which was attributed to cell-cell as well as cell-substrate interactions rather than motility. Thus one may envision that it might be possible to characterize the motility of different cell types as a function of many variables by this new highly sensitive technique based on TSM resonators. Finally the origin of the broad cell resonance was investigated. Improvement of the time resolution reveals the "real" frequency of cell shape fluctuations. Several broad resonances around 3-5 Hz, 15-17 Hz and 25-29 Hz were observed and that could unequivocally be assigned to biological activity of living cells. However, the kind of biological process that provokes this synchronized collective and periodic behavior of the cells remains to be elucidated.

Synthese und Untersuchung von neuen Alpha,Omega-funktionalisierten Lipopolymeren zum Aufbau von polymerunterstützten Lipiddoppelschichten

Ziel dieser Arbeit war es hydrophile Lipopolymere darzustellen, mit denen es möglich sein sollte polymerunterstützte Lipiddoppelschichten auf festen Substratoberflächen zu fixieren. Die Polymere sollten einen Oberflächenanker, eine lipophile Gruppe und ein hydrophiles Polymerrückgrat enthalten. Hierzu wurden Alpha,Omega-funktionalisierte Polymere ausgehend von lipophilen Initiatoren dargestellt. Ausgehend von hydrophoben 2-Brompropionsäureamiden konnte eine kontrollierte radikalische Polymerisation (ATRP) von verschiedenen Acrylamiden durchgeführt werden. So wurden verschiedene Copolymere aus Acrylamid, N-Isopropylacrylamid und N-(3-Dimethylaminopropyl)-acrylamid synthetisiert. Der Einbau des Oberflächenankers als Funktionalität erfolgte indirekt durch Polymerisation eines N-Acryloxysuccinimid Endblocks, welcher in einer anschließenden polymeranalogen Reaktion mit Cysteaminmethyldisulfid umgesetzt wurde.In Ladungsuntersuchungen (PCD) konnte das pH-abhängige Verhalten der Polymere untersucht werden. Der Knäuelkollaps (LCST) der Poly-(N-isopropylacrylamide) wurde mittels Turbidimetrie und DSC charakterisiert. Die Adsorption der Polymere auf Goldoberflächen wurde mit Hilfe der Oberflächenplasmonen Spektroskopie (SPS) aus wässriger Lösung nachgewiesen werden. Dabei bildeten sich ultradünne Filme von 15-20 Å Dicke aus. Kontaktwinkelmessungen wiesen diesen adsorbierten Polymerfilmen ein sehr hydrophiles Verhalten nach. In Lösung adsorbierten die Polymere auf Vesikeloberflächen. Auf ultradünnen Polymerfilmen adsorbierten die Vesikel, wobei mit Hilfe der SPS eine Dickenzunahme um etwa 50 Å nachgewiesen werden konnte. Die ultradünnen Filme der Poly(N-isopropylacrylamide) wiesen eine temperaturabhängige Attraktivität gegenüber Vesikeln auf. Durch gezielte Polystyrol-Entnetzung konnten strukturierte Träger erhalten werden.

Expressions- und Funktionsanalysen von "Tetraspan Vesicle Membrane Proteins" in Caenorhabditis elegans

Tetraspan vesicle membrane proteins (TVPs) sind ubiquitäre Komponenten von Transportvesikeln. Bei den Säugetieren unterscheidet man drei Familien, die Physine, Gyrine und SCAMPs (secretory carrier-associated membrane proteins). Ihre Funktion ist weitgehend unbekannt, es wird jedoch vermutet, dass sie eine Rolle bei der Vesikelbildung und der Vesikelrezirkulierung spielen. In Caenorhabditis elegans existiert von jeder Familie jeweils nur ein einziges Polypeptid: für die Physine Synaptophysin (SPH-1), für die Gyrine Synaptogyrin (SNG-1) und für die SCAMPs SCAMP (SCM-1). Ziel der Arbeit war es die Verteilung der C. elegans TVPs zu untersuchen und ihre Funktion unter besonderer Berücksichtigung der vesikelvermittelten synaptischen Kopplung zu bestimmen. Wenn die C. elegans TVPs in humanen Epithelzellen synthetisiert werden, lokalisieren sie in zytoplasmatischen Vesikeln. In Kotransfektionsexperimenten wurde gezeigt, dass sie größtenteils in den gleichen Strukturen enthalten sind. In C. elegans synthetisierte TVP-Reporterkonstrukte können in unterschiedlichen Geweben nachgewiesen werden. Dabei ist SNG-1 fast ausschließlich in Neuronen zu finden. SPH-1 und SCM-1 hingegen weisen komplexe und teilweise überlappende Verteilungsmuster auf. Während für SPH-1 eine starke Fluoreszenz im Pharynx, auf der apikalen Seite der Darmzellen oberhalb des sog. terminal webs und in adluminalen Regionen von exkretorischen Geweben gefunden wurde, war SCM-1 stark in der Muskulatur und den Coelomozyten vertreten. Die Expression von SCM-1 in Pharynx und Darm war deutlich schwächer. Die C. elegans TVPs werden früh in der Entwicklung ab der Gastrulation (SPH-1 und SCM-1) bzw. ab der Neurulation im sog. Komma-Stadium (SNG-1) produziert. Um die Funktion der TVPs in C. elegans zu untersuchen, wurden TVP-Mutanten analysiert. Durch Kombination aller drei TVP-Gen-Mutanten wurden TVP-Dreifachmutanten generiert. Diese wiesen keinen offensichtlichen Defekt im Bewegungsmuster auf, entwickelten sich normal und bildeten ein normales Nervensystem aus. Auch auf unterschiedliche chemische und physikalische Reize in sensorischen Tests reagierten die TVP-Dreifachmutanten in gleicher Weise wie Wildtyptiere. Ebenso zeigen die TVP-Dreifachmutanten elektrophysiologisch unter normalen Bedingungen keine anormalen Reaktionsmuster. In ultrastrukturellen Untersuchungen wurde lediglich eine signifikant erhöhte Anzahl Clathrin-ummantelter Vesikel in cholinergen Synapsen gefunden. Erst unter Stressbedingungen, hervorgerufen durch den GABA-Antagonisten Pentylentetrazol (PTZ), wiesen sowohl die TVP-Dreifach- als auch die TVP-Einzelmutanten eine deutlich erhöhte Krampfbereitschaft auf. Zusammengenommen zeigen die Analysen, dass TVPs zwar für grundlegende neuronale Prozesse nicht notwendig sind, dass sie aber auf der anderen Seite vermutlich an alternativen redundanten Wegen der Neurotransmitterfreisetzung beteiligt sind.

Single polymers at surfaces: adsorption and detachment

This thesis is concerned with the adsorption and detachment of polymers at planar, rigid surfaces. We have carried out a systematic investigation of adsorption of polymers using analytical techniques as well as Monte Carlo simulations with a coarse grained off-lattice bead spring model. The investigation was carried out in three stages. In the first stage the adsorption of a single multiblock AB copolymer on a solid surface was investigated by means of simulations and scaling analysis. It was shown that the problem could be mapped onto an effective homopolymer problem. Our main result was the phase diagram of regular multiblock copolymers which shows an increase in the critical adsorption potential of the substrate with decreasing size of blocks. We also considered the adsorption of random copolymers which was found to be well described within the annealed disorder approximation. In the next phase, we studied the adsorption kinetics of a single polymer on a flat, structureless surface in the regime of strong physisorption. The idea of a ’stem-flower’ polymer conformation and the mechanism of ’zipping’ during the adsorption process were used to derive a Fokker-Planck equation with reflecting boundary conditions for the time dependent probability distribution function (PDF) of the number of adsorbed monomers. The numerical solution of the time-dependent PDF obtained from a discrete set of coupled differential equations were shown to be in perfect agreement with Monte Carlo simulation results. Finally we studied force induced desorption of a polymer chain adsorbed on an attractive surface. We approached the problem within the framework of two different statistical ensembles; (i) by keeping the pulling force fixed while measuring the position of the polymer chain end, and (ii) by measuring the force necessary to keep the chain end at fixed distance above the adsorbing plane. In the first case we treated the problem within the framework of the Grand Canonical Ensemble approach and derived analytic expressions for the various conformational building blocks, characterizing the structure of an adsorbed linear polymer chain, subject to pulling force of fixed strength. The main result was the phase diagram of a polymer chain under pulling. We demonstrated a novel first order phase transformation which is dichotomic i.e. phase coexistence is not possible. In the second case, we carried out our study in the “fixed height” statistical ensemble where one measures the fluctuating force, exerted by the chain on the last monomer when a chain end is kept fixed at height h over the solid plane at different adsorption strength ε. The phase diagram in the h − ε plane was calculated both analytically and by Monte Carlo simulations. We demonstrated that in the vicinity of the polymer desorption transition a number of properties like fluctuations and probability distribution of various quantities behave differently, if h rather than the force, f, is used as an independent control parameter.

Adsorption of macromolecules on interfaces studied by isothermal titration calorimetry

The mixing of nanoparticles with polymers to form composite materials has been applied for decades. They combine the advantages of polymers (e.g., elasticity, transparency, or dielectric properties) and inorganic nanoparticles (e.g., specific absorption of light, magneto resistance effects, chemical activity, and catalysis etc.). Nanocomposites exhibit several new characters that single-phase materials do not have. Filling the polymeric matrix with an inorganic material requires its homogeneous distribution in order to achieve the highest possible synergetic effect. To fulfill this requirement, the incompatibility between the filler and the matrix, originating from their opposite polarity, has to be resolved. A very important parameter here is the strength and irreversibility of the adsorption of the surface active compound on the inorganic material. In this work the Isothermal titration calorimetry (ITC) was applied as a method to quantify and investigate the adsorption process and binding efficiencies in organic-inorganic–hybrid-systems by determining the thermodynamic parameters (ΔH, ΔS, ΔG, KB as well as the stoichiometry n). These values provide quantification and detailed understanding of the adsorption process of surface active molecules onto inorganic particles. In this way, a direct correlation between the adsorption strength and structure of the surface active compounds can be achieved. Above all, knowledge of the adsorption mechanism in combination with the structure should facilitate a more rational design into the mainly empirically based production and optimization of nanocomposites.

The effect of elastic modulus and equilibrium vapor adsorption on capillary forces

Die Kapillarkraft entsteht durch die Bildung eines Meniskus zwischen zwei Festkörpen. In dieser Doktorarbeit wurden die Auswirkungen von elastischer Verformung und Flϋssigkeitadsorption auf die Kapillarkraft sowohl theoretisch als auch experimentell untersucht. Unter Verwendung eines Rasterkraftmikroskops wurde die Kapillarkraft zwischen eines Siliziumoxid Kolloids von 2 µm Radius und eine weiche Oberfläche wie n.a. Polydimethylsiloxan oder Polyisopren, unter normalen Umgebungsbedingungen sowie in variierende Ethanoldampfdrϋcken gemessen. Diese Ergebnisse wurden mit den Kapillarkräften verglichen, die auf einem harten Substrat (Silizium-Wafer) unter denselben Bedingungen gemessen wurden. Wir beobachteten eine monotone Abnahme der Kapillarkraft mit zunehmendem Ethanoldampfdruck (P) fϋr P/Psat > 0,2, wobei Psat der Sättigungsdampfdruck ist.rnUm die experimentellen Ergebnisse zu erklären, wurde ein zuvor entwickeltes analytisches Modell (Soft Matter 2010, 6, 3930) erweitert, um die Ethanoladsorption zu berϋcksichtigen. Dieses neue analytische Modell zeigte zwei verschiedene Abhängigkeiten der Kapillarkraft von P/Psat auf harten und weichen Oberflächen. Fϋr die harte Oberfläche des Siliziumwafers wird die Abhängigkeit der Kapillarkraft vom Dampfdruck vom Verhältnis der Dicke der adsorbierten Ethanolschicht zum Meniskusradius bestimmt. Auf weichen Polymeroberflächen hingegen hängt die Kapillarkraft von der Oberflächenverformung und des Laplace-Drucks innerhalb des Meniskus ab. Eine Abnahme der Kapillarkraft mit zunehmendem Ethanoldampfdruck hat demnach eine Abnahme des Laplace-Drucks mit zunehmendem Meniskusradius zur folge. rnDie analytischen Berechnungen, fϋr die eine Hertzsche Kontakt-deformation angenommen wurde, wurden mit Finit Element Methode Simulationen verglichen, welche die reale Deformation des elastischen Substrats in der Nähe des Meniskuses explizit berϋcksichtigen. Diese zusätzliche nach oben gerichtete oberflächenverformung im Bereich des Meniskus fϋhrt zu einer weiteren Erhöhung der Kapillarkraft, insbesondere fϋr weiche Oberflächen mit Elastizitätsmodulen < 100 MPa.rn

Plasmonic nanoparticles as sensors : a novel approach to quantify adsorption and diffusion kinetics

Biosensors find wide application in clinical diagnostics, bioprocess control and environmental monitoring. They should not only show high specificity and reproducibility but also a high sensitivity and stability of the signal. Therefore, I introduce a novel sensor technology based on plasmonic nanoparticles which overcomes both of these limitations. Plasmonic nanoparticles exhibit strong absorption and scattering in the visible and near-infrared spectral range. The plasmon resonance, the collective coherent oscillation mode of the conduction band electrons against the positively charged ionic lattice, is sensitive to the local environment of the particle. I monitor these changes in the resonance wavelength by a new dark-field spectroscopy technique. Due to a strong light source and a highly sensitive detector a temporal resolution in the microsecond regime is possible in combination with a high spectral stability. This opens a window to investigate dynamics on the molecular level and to gain knowledge about fundamental biological processes.rnFirst, I investigate adsorption at the non-equilibrium as well as at the equilibrium state. I show the temporal evolution of single adsorption events of fibrinogen on the surface of the sensor on a millisecond timescale. Fibrinogen is a blood plasma protein with a unique shape that plays a central role in blood coagulation and is always involved in cell-biomaterial interactions. Further, I monitor equilibrium coverage fluctuations of sodium dodecyl sulfate and demonstrate a new approach to quantify the characteristic rate constants which is independent of mass transfer interference and long term drifts of the measured signal. This method has been investigated theoretically by Monte-Carlo simulations but so far there has been no sensor technology with a sufficient signal-to-noise ratio.rnSecond, I apply plasmonic nanoparticles as sensors for the determination of diffusion coefficients. Thereby, the sensing volume of a single, immobilized nanorod is used as detection volume. When a diffusing particle enters the detection volume a shift in the resonance wavelength is introduced. As no labeling of the analyte is necessary the hydrodynamic radius and thus the diffusion properties are not altered and can be studied in their natural form. In comparison to the conventional Fluorescence Correlation Spectroscopy technique a volume reduction by a factor of 5000-10000 is reached.

Modeling and simulation of fibrinogen and its adsorption behavior

In this thesis different approaches for the modeling and simulation of the blood protein fibrinogen are presented. The approaches are meant to systematically connect the multiple time and length scales involved in the dynamics of fibrinogen in solution and at inorganic surfaces. The first part of the thesis will cover simulations of fibrinogen on an all atom level. Simulations of the fibrinogen protomer and dimer are performed in explicit solvent to characterize the dynamics of fibrinogen in solution. These simulations reveal an unexpectedly large and fast bending motion that is facilitated by molecular hinges located in the coiled-coil region of fibrinogen. This behavior is characterized by a bending and a dihedral angle and the distribution of these angles is measured. As a consequence of the atomistic detail of the simulations it is possible to illuminate small scale behavior in the binding pockets of fibrinogen that hints at a previously unknown allosteric effect. In a second step atomistic simulations of the fibrinogen protomer are performed at graphite and mica surfaces to investigate initial adsorption stages. These simulations highlight the different adsorption mechanisms at the hydrophobic graphite surface and the charged, hydrophilic mica surface. It is found that the initial adsorption happens in a preferred orientation on mica. Many effects of practical interest involve aggregates of many fibrinogen molecules. To investigate such systems, time and length scales need to be simulated that are not attainable in atomistic simulations. It is therefore necessary to develop lower resolution models of fibrinogen. This is done in the second part of the thesis. First a systematically coarse grained model is derived and parametrized based on the atomistic simulations of the first part. In this model the fibrinogen molecule is represented by 45 beads instead of nearly 31,000 atoms. The intra-molecular interactions of the beads are modeled as a heterogeneous elastic network while inter-molecular interactions are assumed to be a combination of electrostatic and van der Waals interaction. A method is presented that determines the charges assigned to beads by matching the electrostatic potential in the atomistic simulation. Lastly a phenomenological model is developed that represents fibrinogen by five beads connected by rigid rods with two hinges. This model only captures the large scale dynamics in the atomistic simulations but can shed light on experimental observations of fibrinogen conformations at inorganic surfaces.