Development and application of a GC system for NMHC analyses of air samples from the CARIBIC aircraft project

The subject of this thesis is the development of a Gaschromatography (GC) system for non-methane hydrocarbons (NMHCs) and measurement of samples within the project CARIBIC (Civil Aircraft for the Regular Investigation of the atmosphere Based on an Instrument Container, www.caribic-atmospheric.com). Air samples collected at cruising altitude from the upper troposphere and lowermost stratosphere contain hydrocarbons at low levels (ppt range), which imposes substantial demands on detection limits. Full automation enabled to maintain constant conditions during the sample processing and analyses. Additionally, automation allows overnight operation thus saving time. A gas chromatography using flame ionization detection (FID) together with the dual column approach enables simultaneous detection with almost equal carbon atom response for all hydrocarbons except for ethyne. The first part of this thesis presents the technical descriptions of individual parts of the analytical system. Apart from the sample treatment and calibration procedures, the sample collector is described. The second part deals with analytical performance of the GC system by discussing tests that had been made. Finally, results for measurement flight are assessed in terms of quality of the data and two flights are discussed in detail. Analytical performance is characterized using detection limits for each compound, using uncertainties for each compound, using tests of calibration mixture conditioning and carbon dioxide trap to find out their influence on analyses, and finally by comparing the responses of calibrated substances during period when analyses of the flights were made. Comparison of both systems shows good agreement. However, because of insufficient capacity of the CO2 trap the signal of one column was suppressed due to breakthroughed carbon dioxide so much that its results appeared to be unreliable. Plausibility tests for the internal consistency of the given data sets are based on common patterns exhibited by tropospheric NMHCs. All tests show that samples from the first flights do not comply with the expected pattern. Additionally, detected alkene artefacts suggest potential problems with storing or contamination within all measurement flights. Two last flights # 130-133 and # 166-169 comply with the tests therefore their detailed analysis is made. Samples were analyzed in terms of their origin (troposphere vs. stratosphere, backward trajectories), their aging (NMHCs ratios) and detected plumes were compared to chemical signatures of Asian outflows. In the last chapter a future development of the presented system with focus on separation is drawn. An extensive appendix documents all important aspects of the dissertation from theoretical introduction through illustration of sample treatment to overview diagrams for the measured flights.

Vibrational spectroscopic and electrochemical investigations of multi-centered heme proteins in biomimetic membrane architectures

Membrane proteins play a major role in every living cell. They are the key factors in the cell’s metabolism and in other functions, for example in cell-cell interaction, signal transduction, and transport of ions and nutrients. Cytochrome c oxidase (CcO), as one of the membrane proteins of the respiratory chain, plays a significant role in the energy transformation of higher organisms. CcO is a multi centered heme protein, utilizing redox energy to actively transport protons across the mitochondrial membrane. One aim of this dissertation is to investigate single steps in the mechanism of the ion transfer process coupled to electron transfer, which are not fully understood. The protein-tethered bilayer lipid membrane is a general approach to immobilize membrane proteins in an oriented fashion on a planar electrode embedded in a biomimetic membrane. This system enables the combination of electrochemical techniques with surface enhanced resonance Raman (SERRS), surface enhanced reflection absorption infrared (SEIRAS), and surface plasmon spectroscopy to study protein mediated electron and ion transport processes. The orientation of the enzymes within the surface confined architecture can be controlled by specific site-mutations, i.e. the insertion of a poly-histidine tag to different subunits of the enzyme. CcO can, thus, be oriented uniformly with its natural electron pathway entry pointing either towards or away from the electrode surface. The first orientation allows an ultra-fast direct electron transfer(ET) into the protein, not provided by conventional systems, which can be leveraged to study intrinsic charge transfer processes. The second orientation permits to study the interaction with its natural electron donor cytochrome c. Electrochemical and SERR measurements show conclusively that the redox site structure and the activity of the surface confined enzyme are preserved. Therefore, this biomimetic system offers a unique platform to study the kinetics of the ET processes in order to clarify mechanistic properties of the enzyme. Highly sensitive and ultra fast electrochemical techniques allow the separation of ET steps between all four redox centres including the determination of ET rates. Furthermore, proton transfer coupled to ET could be directly measured and discriminated from other ion transfer processes, revealing novel mechanistic information of the proton transfer mechanism of cytochrome c oxidase. In order to study the kinetics of the ET inside the protein, including the catalytic center, time resolved SEIRAS and SERRS measurements were performed to gain more insight into the structural and coordination changes of the heme environment. The electrical behaviour of tethered membrane systems and membrane intrinsic proteins as well as related charge transfer processes were simulated by solving the respective sets of differential equations, utilizing a software package called SPICE. This helps to understand charge transfer processes across membranes and to develop models that can help to elucidate mechanisms of complex enzymatic processes.

Funktionelle Magnetresonanztomographie mittels simultaner EEG-Registrierung interiktaler Spikes bei fokaler Epilepsie: Vergleich der on-, off- mit der häufigkeitskorrelierten Datenanalyse

Obwohl die funktionelle Magnetresonanztomographie (fMRI) interiktaler Spikes mit simultaner EEG-Ableitung bei Patienten mit fokalen Anfallsleiden seit einigen Jahren zur Lokalisation beteiligter Hirnstrukturen untersucht wird, ist sie nach wie vor eine experimentelle Methode. Um zuverlässig Ergebnisse zu erhalten, ist insbesondere die Verbesserung des Signal-zu-Rausch-Verhältnisses in der statistischen Bilddatenauswertung von Bedeutung. Frühere Untersuchungen zur sog. event-related fMRI weisen auf einen Zusammenhang zwischen Häufigkeit von Einzelreizen und nachfolgender hämodynamischer Signalantwort in der fMRI hin. Um einen möglichen Einfluss der Häufigkeit interiktaler Spikes auf die Signalantwort nachzuweisen, wurden 20 Kinder mit fokaler Epilepsie mit der EEG-fMRI untersucht. Von 11 dieser Patienten konnten die Daten ausgewertet werden. In einer zweifachen Analyse mit dem Softwarepaket SPM99 wurden die Bilddaten zuerst ausschließlich je nach Auftreten interiktaler Spikes der „Reiz“- oder „Ruhe“-Bedingung zugeordnet, unabhängig von der jeweiligen Anzahl der Spikes je Messzeitpunkt (on/off-Analyse). In einem zweiten Schritt wurden die „Reiz“- Bedingungen auch differenziert nach jeweiliger Anzahl einzelner Spikes ausgewertet (häufigkeitskorrelierte Analyse). Die Ergebnisse dieser Analysen zeigten bei 5 der 11 Patienten eine Zunahme von Sensitivität und Signifikanzen der in der fMRI nachgewiesenen Aktivierungen. Eine höhere Spezifität konnte hingegen nicht gezeigt werden. Diese Ergebnisse weisen auf eine positive Korrelation von Reizhäufigkeit und nachfolgender hämodynamischer Antwort auch bei interiktalen Spikes hin, welche für die EEG-fMRI nutzbar ist. Bei 6 Patienten konnte keine fMRI-Aktivierung nachgewiesen werden. Mögliche technische und physiologische Ursachen hierfür werden diskutiert.

Bottle microresonators for applications in quantum optics and all-optical signal processing

This thesis reports on the experimental realization, characterization and application of a novel microresonator design. The so-called “bottle microresonator” sustains whispering-gallery modes in which light fields are confined near the surface of the micron-sized silica structure by continuous total internal reflection. While whispering-gallery mode resonators in general exhibit outstanding properties in terms of both temporal and spatial confinement of light fields, their monolithic design makes tuning of their resonance frequency difficult. This impedes their use, e.g., in cavity quantum electrodynamics (CQED) experiments, which investigate the interaction of single quantum mechanical emitters of predetermined resonance frequency with a cavity mode. In contrast, the highly prolate shape of the bottle microresonators gives rise to a customizable mode structure, enabling full tunability. The thesis is organized as follows: In chapter I, I give a brief overview of different types of optical microresonators. Important quantities, such as the quality factor Q and the mode volume V, which characterize the temporal and spatial confinement of the light field are introduced. In chapter II, a wave equation calculation of the modes of a bottle microresonator is presented. The intensity distribution of different bottle modes is derived and their mode volume is calculated. A brief description of light propagation in ultra-thin optical fibers, which are used to couple light into and out of bottle modes, is given as well. The chapter concludes with a presentation of the fabrication techniques of both structures. Chapter III presents experimental results on highly efficient, nearly lossless coupling of light into bottle modes as well as their spatial and spectral characterization. Ultra-high intrinsic quality factors exceeding 360 million as well as full tunability are demonstrated. In chapter IV, the bottle microresonator in add-drop configuration, i.e., with two ultra-thin fibers coupled to one bottle mode, is discussed. The highly efficient, nearly lossless coupling characteristics of each fiber combined with the resonator's high intrinsic quality factor, enable resonant power transfers between both fibers with efficiencies exceeding 90%. Moreover, the favorable ratio of absorption and the nonlinear refractive index of silica yields optical Kerr bistability at record low powers on the order of 50 µW. Combined with the add-drop configuration, this allows one to route optical signals between the outputs of both ultra-thin fibers, simply by varying the input power, thereby enabling applications in all-optical signal processing. Finally, in chapter V, I discuss the potential of the bottle microresonator for CQED experiments with single atoms. Its Q/V-ratio, which determines the ratio of the atom-cavity coupling rate to the dissipative rates of the subsystems, aligns with the values obtained for state-of-the-art CQED microresonators. In combination with its full tunability and the possibility of highly efficient light transfer to and from the bottle mode, this makes the bottle microresonator a unique tool for quantum optics applications.

Antigen-dependent induction of a CD40 signal in peripheral B cells

Monoclonal antibodies have emerged as one of the most promising therapeutics in oncology over the last decades. The generation of fully human tumorantigen-specific antibodies suitable for anti-tumor therapy is laborious and difficult to achieve. Autoreactive B cells expressing those antibodies are detectable in cancer patients and represent a suitable source for human antibodies. However, the isolation and cultivation of this cell type is challenging. A novel method was established to identify antigen-specific B cells. The method is based on the conversion of the antigen independent CD40 signal into an antigen-specific one. For that, the artificial fusion proteins ABCos1 and ABCos2 (Antigen-specific B cell co-stimulator) were generated, which consist of an extracellular association-domain derived from the constant region of the human immunoglobulin (Ig) G1, a transmembrane fragment and an intracellular signal transducer domain derived of the cytoplasmic domain of the human CD40 receptor. By the association with endogenous Ig molecules the heterodimeric complex allows the antigen-specific stimulation of both the BCR and CD40. In this work the ability of the ABCos constructs to associate with endogenous IgG molecules was shown. Moreover, crosslinking of ABCos stimulates the activation of NF-κB in HEK293-lucNifty and induces proliferation in B cells. The stimulation of ABCos in transfected B cells results in an activation pattern different from that induced by the conventional CD40 signal. ABCos activated B cells show a mainly IgG isotype specific activation of memory B cells and are characterized by high proliferation and the differentiation into plasma cells. To validate the approach a model system was conducted: B cells were transfected with IVT-RNA encoding for anti-Plac1 B cell receptor (antigen-specific BCR), ABCos or both. The stimulation with the BCR specific Plac1 peptide induces proliferation only in the cotransfected B cell population. Moreover, we tested the method in human IgG+ memory B cells from CMV infected blood donors, in which the stimulation of ABCos transfected B cells with a CMV peptide induces antigen-specific expansion. These findings show that challenging ABCos transfected B cells with a specific antigen results in the activation and expansion of antigen-specific B cells and not only allows the identification but also cultivation of these B cells. The described method will help to identify antigen-specific B cells and can be used to characterize (tumor) autoantigen-specific B cells and allows the generation of fully human antibodies that can be used as diagnostic tool as well as in cancer therapy.

Genexpressionsanalyse der fötalen Wachstumsfuge des Rindes

Erkrankungen des Skelettapparats wie beispielsweise die Osteoporose oder Arthrose gehören neben den Herz-Kreislauferkrankungen und Tumoren zu den Häufigsten Erkrankungen des Menschen. Ein besseres Verständnis der Bildung und des Erhalts von Knochen- oder Knorpelgewebe ist deshalb von besonderer Bedeutung. Viele bisherige Ansätze zur Identifizierung hierfür relevanter Gene, deren Produkte und Interaktionen beruhen auf der Untersuchung pathologischer Situationen. Daher ist die Funktion vieler Gene nur im Zusammenhang mit Krankheiten beschrieben. Untersuchungen, die die Genaktivität bei der Normalentwicklung von knochen- und knorpelbildenden Geweben zum Ziel haben, sind dagegen weit weniger oft durchgeführt worden. rnEines der entwicklungsphysiologisch interessantesten Gewebe ist die Epiphysenfuge der Röhrenknochen. In dieser sogenannten Wachstumsfuge ist insbesondere beim fötalen Gewebe eine sehr hohe Aktivität derjenigen Gene zu erwarten, die an der Knochen- und Knorpelbildung beteiligt sind. In der vorliegenden Arbeit wurde daher aus der Epiphysenfuge von Kälberknochen RNA isoliert und eine cDNA-Bibliothek konstruiert. Von dieser wurden ca. 4000 Klone im Rahmen eines klassischen EST-Projekts sequenziert. Durch die Analyse konnte ein ungefähr 900 Gene umfassendes Expressionsprofil erstellt werden und viele Transkripte für Komponenten der regulatorischen und strukturbildenden Bestandteile der Knochen- und Knorpelentwicklung identifiziert werden. Neben den typischen Genen für Komponenten der Knochenentwicklung sind auch deutlich Bestandteile für embryonale Entwicklungsprozesse vertreten. Zu ersten gehören in erster Linie die Kollagene, allen voran Kollagen II alpha 1, das mit Abstand höchst exprimierte Gen in der fötalen Wachstumsfuge. Nach den ribosomalen Proteinen stellen die Kollagene mit ca. 10 % aller auswertbaren Sequenzen die zweitgrößte Gengruppe im erstellten Expressionsprofil dar. Proteoglykane und andere niedrig exprimierte regulatorische Elemente, wie Transkriptionsfaktoren, konnten im EST-Projekt aufgrund der geringen Abdeckung nur in sehr geringer Kopienzahl gefunden werden. Allerdings förderte die EST-Analyse mehrere interessante, bisher nicht bekannte Transkripte zutage, die detaillierter untersucht wurden. Dazu gehören Transkripte die, die dem LOC618319 zugeordnet werden konnten. Neben den bisher beschriebenen drei Exonbereichen konnte ein weiteres Exon im 3‘-UTR identifiziert werden. Im abgeleiteten Protein, das mindestens 121 AS lang ist, wurden ein Signalpeptid und eine Transmembrandomäne nachgewiesen. In Verbindung mit einer möglichen Glykosylierung ist das Genprodukt in die Gruppe der Proteoglykane einzuordnen. Leicht abweichend von den typischen Strukturen knochen- und knorpelspezifischer Proteoglykane ist eine mögliche Funktion dieses Genprodukts bei der Interaktion mit Integrinen und der Zell-Zellinteraktion, aber auch bei der Signaltransduktion denkbar. rnDie EST-Sequenzierungen von ca. 4000 cDNA-Klonen können aber in der Regel nur einen Bruchteil der möglichen Transkripte des untersuchten Gewebes abdecken. Mit den neuen Sequenziertechnologien des „Next Generation Sequencing“ bestehen völlig neue Möglichkeiten, komplette Transkriptome mit sehr hoher Abdeckung zu sequenzieren und zu analysieren. Zur Unterstützung der EST-Daten und zur deutlichen Verbreiterung der Datenbasis wurde das Transkriptom der bovinen fötalen Wachstumsfuge sowohl mit Hilfe der Roche-454/FLX- als auch der Illumina-Solexa-Technologie sequenziert. Bei der Auswertung der ca. 40000 454- und 75 Millionen Illumina-Sequenzen wurden Verfahren zur allgemeinen Handhabung, der Qualitätskontrolle, dem „Clustern“, der Annotation und quantitativen Auswertung von großen Mengen an Sequenzdaten etabliert. Beim Vergleich der Hochdurchsatz Blast-Analysen im klassischen „Read-Count“-Ansatz mit dem erstellten EST-Expressionsprofil konnten gute Überstimmungen gezeigt werden. Abweichungen zwischen den einzelnen Methoden konnten nicht in allen Fällen methodisch erklärt werden. In einigen Fällen sind Korrelationen zwischen Transkriptlänge und „Read“-Verteilung zu erkennen. Obwohl schon simple Methoden wie die Normierung auf RPKM („reads per kilo base transkript per million mappable reads“) eine Verbesserung der Interpretation ermöglichen, konnten messtechnisch durch die Art der Sequenzierung bedingte systematische Fehler nicht immer ausgeräumt werden. Besonders wichtig ist daher die geeignete Normalisierung der Daten beim Vergleich verschieden generierter Datensätze. rnDie hier diskutierten Ergebnisse aus den verschiedenen Analysen zeigen die neuen Sequenziertechnologien als gute Ergänzung und potentiellen Ersatz für etablierte Methoden zur Genexpressionsanalyse.rn

Influence of defects and disorder on anomalous Hall effect and spin Seebeck effect on permalloy and Heusler compounds

In dieser Arbeit wurden dünne Schichten von Heusler-Verbindungen hergestellt und auf ihre Transporteigenschaften hin untersucht.rnDer Anomale Hall-Effekt (AHE) ist dabei von besonderem Interesse. Er ist ein seit langer Zeit bekannter, jedoch noch nicht vollständig verstandener Transport-Effekt. Die meisten Veröffentlichungen theoretischer Arbeiten konzentrieren sich auf den Einfluss eines bestimmten Beitrags zum AHE. Tatsächlich gemessene experimentelle Daten können jedoch oft nicht in Einklang mit idealisierten Annahmen gebracht werden. rnDie vorliegende Arbeit diskutiert die Ergebnisse, welche aus Messungen von Materialien mit niedrigem Restwiderstand erhalten wurden. rnrnAls prototypische Materialien wurden hier hyphenation Heusler-Verbindungen untersucht. Als Material mit einer komplexen Topologie der Fermi-Fläche zeichnet sich dort der Einfluss von Defekten und der Unordnung der Kristallstruktur deutlich ab.rnrnDurch Verwendung von Filmen mit unterschiedlichem Grad der Unordnung können verschiedene Streumechanismen unterschieden werden. Für Co$_{2}$FeSi$_{0.6}$Al$_{0.4}$ and Co$_{2}$FeGa$_{0.5}$Ge$_{0.5}$ zeigt sich ein positiver AHE bei einer Unordnung vom Typ B2 und bei einer induzierten temperaturabh"angigen Streuung, wo hingegen eine Typ DO$_{3}$-Unordnung zusammen mit anderen möglichen intrinsischen Beiträgen einen negativen Effekt hervorruft.rnrnDarüber hinaus wurden die magneto-optische Kerr-Effekte (MOKE) dieser Verbindungen untersucht. Hierfür wurden Beiträge erster Ordnung als Funktion der intrinsischen und extrinsischen Parameter qualitativ analysiert. Auf den Einfluss der kristallinen Ordnung auf Beiträge zweiter Ordnung des MOKE-Signals wird ebenfalls eingegangen.rnrnDes Weiteren wurden dünne Schichten der Heusler-Verbindung Co$_{2}$MnAl auf MgO- und Si-Subs-traten (beide (100)) mit Hochfrequenz-Mag-netron-Sputtern erzeugt. Die zusammensetzung sowie die magnetischen und Transport-Eigenschaften wurden hinsichtlich unterschiedlicher Abscheidebedingungen systematisch untersucht.rnrnInsbesondere zeigt der AHE-Widerstand ein außerordentliches temperaturunabhängiges Verhalten in einem Bereich moderater Magnetfeldstärken von 0 bis 0.6,T. Hierf"ur wurde der nicht-diagonale Transport bei Temperaturen bis zu 300,$^{circ}$C analysiert. Die Daten zeigen die Eignung des Materials für Hall-Sensoren auch oberhalb der Raumtemperatur.rnrnJüngst wurde der Spin Seebeck-Effekt (SSE) entdeckt. Der Effekt aus dem Bereich der Spin-Kaloritronik erzeugt eine Spin-Spannung'' aufgrund eines Temperaturgradienten in magnetischen Materialien. Hier werden vorläufige Messungen des SSE in Ni$_{80}$Fe$_{20}$ und in Heusler-Verbindungen präsentiert.rn

Software tools and efficient algorithms for the feature detection, feature tracking, event localization, and visualization of large sets of atmospheric data

Data sets describing the state of the earth's atmosphere are of great importance in the atmospheric sciences. Over the last decades, the quality and sheer amount of the available data increased significantly, resulting in a rising demand for new tools capable of handling and analysing these large, multidimensional sets of atmospheric data. The interdisciplinary work presented in this thesis covers the development and the application of practical software tools and efficient algorithms from the field of computer science, aiming at the goal of enabling atmospheric scientists to analyse and to gain new insights from these large data sets. For this purpose, our tools combine novel techniques with well-established methods from different areas such as scientific visualization and data segmentation. In this thesis, three practical tools are presented. Two of these tools are software systems (Insight and IWAL) for different types of processing and interactive visualization of data, the third tool is an efficient algorithm for data segmentation implemented as part of Insight.Insight is a toolkit for the interactive, three-dimensional visualization and processing of large sets of atmospheric data, originally developed as a testing environment for the novel segmentation algorithm. It provides a dynamic system for combining at runtime data from different sources, a variety of different data processing algorithms, and several visualization techniques. Its modular architecture and flexible scripting support led to additional applications of the software, from which two examples are presented: the usage of Insight as a WMS (web map service) server, and the automatic production of a sequence of images for the visualization of cyclone simulations. The core application of Insight is the provision of the novel segmentation algorithm for the efficient detection and tracking of 3D features in large sets of atmospheric data, as well as for the precise localization of the occurring genesis, lysis, merging and splitting events. Data segmentation usually leads to a significant reduction of the size of the considered data. This enables a practical visualization of the data, statistical analyses of the features and their events, and the manual or automatic detection of interesting situations for subsequent detailed investigation. The concepts of the novel algorithm, its technical realization, and several extensions for avoiding under- and over-segmentation are discussed. As example applications, this thesis covers the setup and the results of the segmentation of upper-tropospheric jet streams and cyclones as full 3D objects. Finally, IWAL is presented, which is a web application for providing an easy interactive access to meteorological data visualizations, primarily aimed at students. As a web application, the needs to retrieve all input data sets and to install and handle complex visualization tools on a local machine are avoided. The main challenge in the provision of customizable visualizations to large numbers of simultaneous users was to find an acceptable trade-off between the available visualization options and the performance of the application. Besides the implementational details, benchmarks and the results of a user survey are presented.

The importance of visual and olfactory stimuli during flower visits in Apis mellifera

Flowers attract honeybees using colour and scent signals. Bimodality (having both scent and colour) in flowers leads to increased visitation rates, but how the signals influence each other in a foraging situation is still quite controversial. We studied four basic questions: When faced with conflicting scent and colour information, will bees choose by scent and ignore the “wrong” colour, or vice versa? To get to the bottom of this question, we trained bees on scent-colour combination AX (rewarded) versus BY (unrewarded) and tested them on AY (previously rewarded colour and unrewarded scent) versus BX (previously rewarded scent and unrewarded colour). It turned out that the result depends on stimulus quality: if the colours are very similar (unsaturated blue and blue-green), bees choose by scent. If they are very different (saturated blue and yellow), bees choose by colour. We used the same scents, lavender and rosemary, in both cases. Our second question was: Are individual bees hardwired to use colour and ignore scent (or vice versa), or can this behaviour be modified, depending on which cue is more readily available in the current foraging context? To study this question, we picked colour-preferring bees and gave them extra training on scent-only stimuli. Afterwards, we tested if their preference had changed, and if they still remembered the scent stimulus they had originally used as their main cue. We came to the conclusion that a colour preference can be reversed through scent-only training. We also gave scent-preferring bees extra training on colour-only stimuli, and tested for a change in their preference. The number of animals tested was too small for statistical tests (n = 4), but a common tendency suggested that colour-only training leads to a preference for colour. A preference to forage by a certain sensory modality therefore appears to be not fixed but flexible, and adapted to the bee’s surroundings. Our third question was: Do bees learn bimodal stimuli as the sum of their parts (elemental learning), or as a new stimulus which is different from the sum of the components’ parts (configural learning)? We trained bees on bimodal stimuli, then tested them on the colour components only, and the scent components only. We performed this experiment with a similar colour set (unsaturated blue and blue-green, as above), and a very different colour set (saturated blue and yellow), but used lavender and rosemary for scent stimuli in both cases. Our experiment yielded unexpected results: with the different colours, the results were best explained by elemental learning, but with the similar colour set, bees exhibited configural learning. Still, their memory of the bimodal compound was excellent. Finally, we looked at reverse-learning. We reverse-trained bees with bimodal stimuli to find out whether bimodality leads to better reverse-learning compared to monomodal stimuli. We trained bees on AX (rewarded) versus BY (unrewarded), then on AX (unrewarded) versus BY (rewarded), and finally on AX (rewarded) and BY (unrewarded) again. We performed this experiment with both colour sets, always using the same two scents (lavender and rosemary). It turned out that bimodality does not help bees “see the pattern” and anticipate the switch. Generally, bees trained on the different colour set performed better than bees trained on the similar colour set, indicating that stimulus salience influences reverse-learning.