7 resultados para Scanning and Transmission Electron Microscopies

em ArchiMeD - Elektronische Publikationen der Universität Mainz - Alemanha


Relevância:

100.00% 100.00%

Publicador:

Resumo:

Here, we present the adaptation and optimization of (i) the solvothermal and (ii) the metal-organic chemical vapor deposition (MOCVD) approach as simple methods for the high-yield synthesis of MQ2 (M=Mo, W, Zr; Q = O, S) nanoparticles. Extensive characterization was carried out using X-ray diffraction (XRD), scanning and transmission electron micros¬copy (SEM/TEM) combined with energy dispersive X-ray analysis (EDXA), Raman spectroscopy, thermal analyses (DTA/TG), small angle X-ray scattering (SAXS) and BET measurements. After a general introduction to the state of the art, a simple route to nanostructured MoS2 based on the decomposition of the cluster-based precursor (NH4)2Mo3S13∙xH2O under solvothermal conditions (toluene, 653 K) is presented. Solvothermal decomposition results in nanostructured material that is distinct from the material obtained by decomposition of the same precursor in sealed quartz tubes at the same temperature. When carried out in the presence of the surfactant cetyltrimethyl¬ammonium bromide (CTAB), the decomposition product exhibits highly disordered MoS2 lamellae with high surface areas. The synthesis of WS2 onion-like nanoparticles by means of a single-step MOCVD process is discussed. Furthermore, the results of the successful transfer of the two-step MO¬CVD based synthesis of MoQ2 nanoparticles (Q = S, Se), comprising the formation of amorphous precursor particles and followed by the formation of fullerene-like particles in a subsequent annealing step to the W-S system, are presented. Based on a study of the temperature dependence of the reactions a set of conditions for the formation of onion-like structures in a one-step reaction could be derived. The MOCVD approach allows a selective synthesis of open and filled fullerene-like chalcogenide nanoparticles. An in situ heating stage transmission electron microscopy (TEM) study was employed to comparatively investigate the growth mechanism of MoS2 and WS2 nanoparticles obtained from MOCVD upon annealing. Round, mainly amorphous particles in the pristine sample trans¬form to hollow onion-like particles upon annealing. A significant difference between both compounds could be demonstrated in their crystallization conduct. Finally, the results of the in situ hea¬ting experiments are compared to those obtained from an ex situ annealing process under Ar. Eventually, a low temperature synthesis of monodisperse ZrO2 nanoparticles with diameters of ~ 8 nm is introduced. Whereas the solvent could be omitted, the synthesis in an autoclave is crucial for gaining nano-sized (n) ZrO2 by thermal decomposition of Zr(C2O4)2. The n-ZrO2 particles exhibits high specific surface areas (up to 385 m2/g) which make them promising candidates as catalysts and catalyst supports. Co-existence of m- and t-ZrO2 nano-particles of 6-9 nm in diameter, i.e. above the critical particle size of 6 nm, demonstrates that the particle size is not the only factor for stabilization of the t-ZrO2 modification at room temperature. In conclusion, synthesis within an autoclave (with and without solvent) and the MOCVD process could be successfully adapted to the synthesis of MoS2, WS2 and ZrO2 nanoparticles. A comparative in situ heating stage TEM study elucidated the growth mechanism of MoS2 and WS2 fullerene-like particles. As the general processes are similar, a transfer of this synthesis approach to other layered transition metal chalcogenide systems is to be expected. Application of the obtained nanomaterials as lubricants (MoS2, WS2) or as dental filling materials (ZrO2) is currently under investigation.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Dendritic cells (DCs) are the most potent cell type for capture, processing, and presentation of antigens. They are able to activate naïve T cells as well as to initiate memory T-cell immune responses. T lymphocytes are key elements in eliciting cellular immunity against bacteria and viruses as well as in the generation of anti-tumor and anti-leukemia immune responses. Because of their central position in the immunological network, specific manipulations of these cell types provide promising possibilities for novel immunotherapies. Nanoparticles (NP) that have just recently been investigated for use as carriers of drugs or imaging agents, are well suited for therapeutic applications in vitro and also in vivo since they can be addressed to cells with a high target specificity upon surface functionalization. As a first prerequisite, an efficient in vitro labeling of cells with NP has to be established. In this work we developed protocols allowing an effective loading of human monocyte-derived DCs and primary antigen-specific T cells with newly designed NP without affecting biological cell functions. Polystyrene NP that have been synthesized by the miniemulsion technique contained perylenmonoimide (PMI) as a fluorochrome, allowing the rapid determination of intracellular uptake by flow cytometry. To confirm intracellular localization, NP-loaded cells were analyzed by confocal laser scanning microscopy (cLSM) and transmission electron microscopy (TEM). Functional analyses of NP-loaded cells were performed by IFN-γ ELISPOT, 51Chromium-release, and 3H-thymidine proliferation assays. In the first part of this study, we observed strong labeling of DCs with amino-functionalized NP. Even after 8 days 95% of DCs had retained nanoparticles with a median fluorescence intensity of 67% compared to day 1. NP loading did not influence expression of cell surface molecules that are specific for mature DCs (mDCs) nor did it influence the immunostimulatory capacity of mDCs. This procedure did also not impair the capability of DCs for uptake, processing and presentation of viral antigens that has not been shown before for NP in DCs. In the second part of this work, the protocol was adapted to the very different conditions with T lymphocytes. We used leukemia-, tumor-, and allo-human leukocyte antigen (HLA) reactive CD8+ or CD4+ T cells as model systems. Our data showed that amino-functionalized NP were taken up very efficiently also by T lymphocytes, which usually had a lower capacity for NP incorporation compared to other cell types. In contrast to DCs, T cells released 70-90% of incorporated NP during the first 24 h, which points to the need to escape from intracellular uptake pathways before export to the outside can occur. Preliminary data with biodegradable nanocapsules (NC) revealed that encapsulated cargo molecules could, in principle, escape from the endolysosomal compartment after loading into T lymphocytes. T cell function was not influenced by NP load at low to intermediate concentrations of 25 to 150 μg/mL. Overall, our data suggest that NP and NC are promising tools for the delivery of drugs, antigens, and other molecules into DCs and T lymphocytes.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

We report on a strategy to prepare metal oxides including binary oxide and mixed metal oxide (MMO) in form of nanometer-sized particles using polymer as precursor. Zinc oxide nanoparticles are prepared as an example. The obtained zinc polyacrylate precursor is amorphous as confirmed by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The conversion from polymer precursor to ZnO nanocrystals by thermal pyrolysis was investigated by means of XRD, thermogravimetric analysis (TGA) and electron microscopy. The as-synthesized ZnO consists of many individual particles with a diameter around 40 nm as shown by scanning electron microscopy (SEM). The photoluminescence (PL) and electron paramagnetic (EPR) properties of the material are investigated, too. Employing this method, ZnO nanocrystalline films are fabricated via pyrolysis of a zinc polyacrylate precursor film on solid substrate like silicon and quartz glass. The results of XRD, absorption spectra as well as TEM prove that both the ZnO nanopowder and film undergo same evolution process. Comparing the PL properties of films fabricated in different gas atmosphere, it is assigned that the blue emission of the ZnO films is due to crystal defect of zinc vacancy and green emission from oxygen vacancy. Two kinds of ZnO-based mixed metal oxide (Zn1-xMgxO and Zn1-xCoxO) particles with very precise stoichiometry are prepared by controlled pyrolysis of the corresponding polymer precursor at 550 oC. The MMO crystal particles are typically 20-50 nm in diameter. Doping of Mg in ZnO lattice causes shrinkage of lattice parameter c, while it remains unchanged with Co incorporation. Effects of bandgap engineering are seen in the Mg:ZnO system. The photoluminescence in the visible is enhanced by incorporation of magnesium on zinc lattice sites, while the emission is suppressed in the Co:ZnO system. Magnetic property of cobalt doped-ZnO is checked too and ferromagnetic ordering was not found in our samples. An alternative way to prepare zinc oxide nanoparticles is presented upon calcination of zinc-loaded polymer precursors, which is synthesized via inverse miniemulsion polymerization of the mixture of the acrylic acid and zinc nitrate. The as-prepared ZnO product is compared with that obtained from polymer-salt complex method. The obtained ZnO nanoparticles undergo surface modification via a phosphate modifier applying ultrasonication. The morphology of the modified particles is checked by SEM. And stability of the ZnO nanoparticles in aqueous dispersion is enhanced as indicated by the zeta-potential results.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In der vorliegenden Arbeit wurden Materialien und Aufbauten für Hybrid Solarzellen entwickelt und erforscht. rnDer Vergleich zweier bekannter Lochleitermaterialien für Solarzellen in einfachen Blend-Systemen brachte sowohl Einsicht zur unterschiedlichen Eignung der Materialien für optoelektronische Bauelemente als auch neue Erkenntnisse in Bereichen der Langzeitstabilität und Luftempfindlichkeit beider Materialien.rnWeiterhin wurde eine Methode entwickelt, um Hybrid Solarzelle auf möglichst unkomplizierte Weise aus kostengünstigen Materialien darzustellen. Die „Eintopf“-Synthese ermöglicht die unkomplizierte Darstellung eines funktionalen Hybridmaterials für die optoelektronische Anwendung. Mithilfe eines neu entwickelten amphiphilen Blockcopolymers, das als funktionelles Templat eingesetzt wurde, konnten mit einem TiO2-Precursor in einem Sol-Gel Ansatz verschiedene selbstorganisierte Morphologien des Hybridmaterials erhalten werden. Verschiedene Morphologien wurden auf ihre Eignung in Hybrid Solarzellen untersucht. Ob und warum die Morphologie des Hybridsystems die Effizienz der Solarzelle beeinflusst, konnte verdeutlicht werden. Mit der Weiterentwicklung der „Eintopf“-Synthese, durch den Austausch des TiO2-Precursors, konnte die Solarzelleneffizienz von 0.15 auf 0.4 % gesteigert werden. Weiterhin konnte die Übertragbarkeit des Systems durch den erfolgreichen Austausch des Halbleiters TiO¬2 mit ZnO bewiesen werden.rn

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Nanopartikel durch Strukturfixierung mizellarer Assoziate aus amphiphilen, endgruppenfunktionalisierten Diblockcopolymeren Zwei unterschiedliche Diblockcopolymersysteme mit Molmassen unterhalb von Mw = 10 000 g/mol wurden über anionische Polymerisation synthetisiert. Ein hetero-telecheles a,w-Poly(dimethylsiloxan)-b-Poly(ethylenoxid) (PDMS-PEO) Diblockcopolymer wurde mit einer Methacrylatendgruppe am PDMS und entweder einer Benzyl-, Hydroxy- oder Carboxylatendgruppe am PEO funktionalisiert. Ein Poly(butadien)-b-Poly(ethylenoxid) (PB-PEO) Diblockcopolymer wurde am PEO ebenfalls entweder mit einer Benzyl-, Hydroxy- oder Carboxylatendgruppe funktionalisiert. In selektiven Lösungsmitteln wie Wasser oder Methanol bilden beide Diblockcopolymersysteme supramolekulare Strukturen mit sphärischer, zylindrischer oder toroider Geometrie aus, die mit statischer und dynamischer Lichtstreuung in Lösung und mit Rasterkraftmikroskopie (AFM) und Transmissionselektronenmikroskopie (TEM) auf der Oberfläche untersucht wurden. Durch Zusatz eines Vernetzers und Initiators wurden die selbstassoziierenden Mizellen des PDMS-PEO Diblockcopolymers permanent durch radikalische Polymerisation mit UV-Licht fixiert. Mizellen des PB-PEO Diblockcopolymers wurden über Bestrahlung mit gamma-Strahlen permanent fixiert. Die Untersuchung der resultierenden Nanopartikel beider Diblockcopolymersysteme mit AFM und TEM zeigte, daß diese sogar in nicht selektiven Lösungsmitteln wie Tetrahydrofuran formstabil bleiben.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In der eingereichten Arbeit wurde die Nutzung von nicht-wässrigen Emulsionen, bestehend aus zwei organischen, aprotischen Lösungsmitteln, zur Erzeugung verschiedener polymerer Nanopartikel beschrieben. Diese Zweiphasenmischungen und die Verwendung maßgeschneiderter Emulgatoren bestehend aus Poly(isopren-block-methylmethacrylat) ermöglichten den Zugang zu einer Vielzahl an Reaktionen und Prozessen, welche in wässrigen Emulsionen bisher nicht oder nur schwer möglich waren. Die Generierung von Partikeln auf Basis katalytischer Polymerisationen erfolgte unter Verwendung der Ringöffnenden Metathese-Polymerisation (ROMP), der Acyclischen Dien-Metathese-Polymerisation (ADMET), der Cyclopolymerisation von α,ω-Diinen und der Ni-katalysierten Polymerisation von Isocyaniden. Mittels ROMP konnten stabile Dispersionen erzeugt werden, welche Partikel mit verschiedensten Molekulargewichten, Größen und Morphologien enthielten. Diese Eigenschaften konnten durch die Wahl des Monomers, die Katalysatorkonzentration oder den Emulgatortyp beeinflusst werden. Des Weiteren wurden Partikel mit komplexen Morphologien wie Kern-Schale-Strukturen synthetisiert. Dazu erfolgte die Generierung von Partikeln aus Poly(urethan) oder Poly(norbornenderivaten), welche in situ und ohne intermediäre Aufarbeitung mit einer Schale aus Poly(methacrylat) versehen wurden. Der Nachweis dieser Strukturen gelang mittels verschiedener Schwermetall-Markierungsverfahren in der Transmissionselektronenmikroskopie. Schlussendlich erfolgte die Herstellung von hochvernetzten und molekular geprägten Poly(acrylsäure)-Partikeln. Hierbei wurden unterschiedliche pharmakologische Wirkstoffe und Farbstoffe in die Partikel eingebracht, um deren Migrationsverhalten und Wiederanbindung an die Partikel zu untersuchen. Weiterhin wurden die Partikel erfolgreich in Zellaufnahmeexperimenten eingesetzt.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Plasmons in metal nanoparticles respond to changes in their local environment by a spectral shift in resonance. Here, the potential of plasmonic metal nanoparticles for label-free detection and observation of biological systems is presented. Comparing the material silver and gold concerning plasmonic sensitivity, silver nanoparticles exhibit a higher sensitivity but their chemical instability under light exposure limits general usage. A new approach combining results from optical dark-field microscopy and transmission electron microscopy allows localization and quantification of gold nanoparticles internalized into living cells. Nanorods exposing a negatively charged biocompatible polymer seem to be promising candidates to sense membrane fluctuations of adherent cells. Many small nanoparticles being specific sensing elements can build up a sensor for parallel analyte detection without need of labeling, which is easy to fabricate, re-usable, and has sensitivity down to nanomolar concentrations. Besides analyte detection, binding kinetics of various partner proteins interacting with one protein of interest are accessible in parallel. Gold nanoparticles are able to sense local oscillations in the surface density of proteins on a lipid bilayer, which could not be resolved so far. Studies on the fluorescently labeled system and the unlabeled system identify an influence of the label on the kinetics.