Structure property relations in complex copolymer systems

A thorough investigation was made of the structure-property relation of well-defined statistical, gradient and block copolymers of various compositions. Among the copolymers studied were those which were synthesized using isobornyl acrylate (IBA) and n-butyl acrylate (nBA) monomer units. The copolymers exhibited several unique properties that make them suitable materials for a range of applications. The thermomechanical properties of these new materials were compared to acrylate homopolymers. By the proper choice of the IBA/nBA monomer ratio, it was possible to tune the glass transition temperature of the statistical P(IBA-co-nBA) copolymers. The measured Tg’s of the copolymers with different IBA/nBA monomer ratios followed a trend that fitted well with the Fox equation prediction. While statistical copolymers showed a single glass transition (Tg between -50 and 90 ºC depending on composition), DSC block copolymers showed two Tg’s and the gradient copolymer showed a single, but very broad, glass transition. PMBL-PBA-PMBL triblock copolymers of different composition ratios were also studied and revealed a microphase separated morphology of mostly cylindrical PMBL domains hexagonally arranged in the PBA matrix. DMA studies confirmed the phase separated morphology of the copolymers. Tensile studies showed the linear PMBL-PBA-PMBL triblock copolymers having a relatively low elongation at break that was increased by replacing the PMBL hard blocks with the less brittle random PMBL-r-PMMA blocks. The 10- and 20-arm PBA-PMBL copolymers which were studied revealed even more unique properties. SAXS results showed a mixture of cylindrical PMBL domains hexagonally arranged in the PBA matrix, as well as lamellar. Despite PMBL’s brittleness, the triblock and multi-arm PBA-PMBL copolymers could become suitable materials for high temperature applications due to PMBL’s high glass transition temperature and high thermal stability. The structure-property relation of multi-arm star PBA-PMMA block copolymers was also investigated. Small-angle X-ray scattering revealed a phase separated morphology of cylindrical PMMA domains hexagonally arranged in the PBA matrix. DMA studies found that these materials possess typical elastomeric behavior in a broad range of service temperatures up to at least 250°C. The ultimate tensile strength and the elastic modulus of the 10- and 20-arm star PBA-PMMA block copolymers are significantly higher than those of their 3-arm or linear ABA type counterparts with similar composition, indicating a strong effect of the number of arms on the tensile properties. Siloxane-based copolymers were also studied and one of the main objectives here was to examine the possibility to synthesize trifluoropropyl-containing siloxane copolymers of gradient distribution of trifluoropropyl groups along the chain. DMA results of the PDMS-PMTFPS siloxane copolymers synthesized via simultaneous copolymerization showed that due to the large difference in reactivity rates of 2,4,6-tris(3,3,3-trifluoropropyl)-2,4,6-trimethylcyclotrisiloxane (F) and hexamethylcyclotrisiloxane (D), a copolymer of almost block structure containing only a narrow intermediate fragment with gradient distribution of the component units was obtained. A more dispersed distribution of the trifluoropropyl groups was obtained by the semi-batch copolymerization process, as the DMA results revealed more ‘‘pure gradient type’’ features for the siloxane copolymers which were synthesized by adding F at a controlled rate to the polymerization of the less reactive D. As with trifluoropropyl-containing siloxane copolymers, vinyl-containing polysiloxanes may be converted to a variety of useful polysiloxane materials by chemical modification. But much like the trifluoropropyl-containing siloxane copolymers, as a result of so much difference in the reactivities between the component units 2,4,6-trivinyl-2,4,6-trimethylcyclotrisiloxane (V) and hexamethylcyclotrisiloxane (D), thermal and mechanical properties of the PDMS-PMVS copolymers obtained by simultaneous copolymerization was similar to those of block copolymers. Only the copolymers obtained by semi-batch method showed properties typical for gradient copolymers.

Beeinflussung der Grenzflächenspannung zwischen den Schmelzen "unverträglicher" Homopolymere durch Copolymere

Im Rahmen dieser Arbeit wurde am System Polyethylenoxid / Polypropylenoxid (PEO / PPO) der Einfluß von Copolymeren auf die Grenzflächenspannung Sigma von Homopolymerblends untersucht. Als Additive dienten Triblockcopolymere EO-block-PO-block-EO bzw. PO-block-EO-block-PO, Diblockcopolymere S-block-EO sowie statistische Copolymere EO-ran-PO. Die Additive wurden so ausgewählt, daß sich Paare von Additiven jeweils in genau einer Eigenschaft (Zusammensetzung, Kettenlänge, Blockanordnung) unterscheiden, in allen anderen Parametern jedoch vergleichbar sind. Die Grenzflächenspannung wurde experimentell mit Hilfe der Pendant-Drop-Methode in Abhängigkeit von der Temperatur ermittelt, wobei das Polymer mit der höheren Dichte, PEO, die Tropfenphase und PPO die Matrixphase bildet. Das Additiv wurde bei Messung der Grenzflächenspannung der ternären Systeme in unterschiedlichen Konzentrationen entweder einer oder beiden Homopolymerphasen zugegeben. Die Konzentrationsabhängigkeit von Sigma lässt sich sowohl mit dem Modell von Tang und Huang als auch mit einem Langmuir-analogen Ansatz gut beschreiben.Um den Zusammenhang zwischen sigma und dem Phasenverhalten zu untersuchen, wurden für einige der ternären Systeme Trübungskurven bei 100°C aufgenommen. Der Vergleich zwischen den Phasendiagrammen und den korrespondierenden Werten von sigma weist darauf hin, dass ein Additiv sigma gerade dann wirksam reduziert, wenn es einem Homopolymer zugefügt wird, mit dem es nur begrenzt verträglich ist, da dann die Triebkraft zur Anlagerung an der Grenzfläche besonders ausgeprägt ist. Das bereits bekannte Phänomen, wonach der Wert der Grenzflächenspannung davon abhängig sein kann, in welcher der Phasen das Additiv zu Beginn der Messung vorliegt, wurde ausführlich untersucht. Es wird angenommen, dass das System nicht in jedem Fall das thermodynamische Gleichgewicht erlangt und der beobachtete Effekt auf das Erreichen stationärer Zustände zurückzuführen ist. Dieses Verhalten kann mit einem Modell beschrieben werden, in welches das Viskositätsverhältnis der Homopolymere sowie der Verteilungskoeffizient des Copolymers zwischen den Homopolymerphasen eingehen. Aus Löslichkeitsparametern wurde der binäre Wechselwirkungsparameter Chi PEO/PPO = 0.18 abgeschätzt und mit diesem die theoretischen Werte für sigma zwischen PEO und PPO nach den Modellen von Roe bzw. Helfand und Tagami berechnet. Der Vergleich mit den experimentellen Daten des binären Systems zeigt, dass beide Ansätze sigma-Werte liefern, die in der Größenordnung der experimentellen Daten liegen, hierbei erweist sich der Ansatz von Roe als besonders geeignet. Die Temperaturabhängigkeit der Grenzflächenspannung wird jedoch durch beide Ansätze unzutreffend wiedergegeben. Mit dem Modell von Helfand und Tagami wurden eine Grenzflächendicke von 7.9 Å und das Dichteprofil der Grenzfläche berechnet. Für die Copolymere EO92PO56EO92 und S9EO22 (die Indices geben die Zahl der Monomereinheiten an) können die Grenzflächenüberschusskonzentrationen, die kritische Mizellenkonzentration sowie der einem Additivmolekül an der Grenzschicht zur Verfügung stehende Platz bestimmt werden.Der Vergleich unterschiedlicher Copolymere hinsichtlich ihrer Fähigkeit, sigma wirkungsvoll herabzusetzen, zeigt, dass im Fall von Triblockcopolymeren die Anordnung der Blöcke gegenüber der Zusammensetzung eine untergeordnete Rolle spielt. Mit zunehmender Kettenlänge nimmt die Effektivität als Compatibilizer sowohl bei Blockcopolymeren als auch bei statistischen Copolymeren zu.

Rod-coil copolymer structures

Skalenargumente werden verwendet, um Rod-Coil Copolymere mit fester Zusammensetzung von steifen Stäbchen und flexiblen Ketten zu studieren. In einem selektiven Lösungsmittel, in dem sich nur die Ketten lösen, bildet ein Rod-Coil Multiblock zylinderförmige Micellen aus aggregierten Stäbchen verbunden durch Kettenstücke. Die Stäbchen aggregieren, um Energie zu gewinnen. Dieser Prozeß wird durch den Entropieverlust der flexiblen Ketten ausgeglichen. Das Adsorptionsverhalten von Aggregaten aus parallel aneinandergelagerten, einzelnen Rod-Coil Diblöcken in selektivem Lösungsmittel wird anhand von erweiterten Skalenbetrachtungen diskutiert. Wenn ein solches Aggregat mit den Stäbchen parallel zur Oberfläche adsorbiert, verschieben sich die Stäbchen gegeneinander. Zusätzlich werden die Stabilität der adsorbierten Aggregate und andere mögliche Konfigurationen untersucht. Um einen Rod-Coil Multiblock mit variabler Zusammensetzung zu studieren, wird eine Feldtheorie entwickelt. Jedes Segment kann entweder steif oder flexibel sein. Das System zeigt drei Phasenzustände, offene Kette, amorphe Globule und flüssig-kristalline Globule. Beim Übergang von amorpher zu flüssig-kristalliner Globule steigt der Anteil an steifen Segmenten rapide an. Dieser Übergang wird durch die isotrope Wechselwirkung zwischen den steifen Segmenten und die anisotrope Oberflächenenergie der Globule verursacht.

Structure and properties of composite polyolefin materials

This thesis is based on three main studies, all dealing with structure-property investigation of semicrystalline polyolefin-based composites. Low density poly(ethylene) (LDPE) and isotactic poly(propylene) (iPP) were chosen as parts of the composites materials and they were investigated either separately (as homoploymers), either in blend systems with the composition LDPE/iPP 80/20 or as filled matrix with layered silicate (montmorillonite). The beneficial influence of adding ethylene-co-propylene polymer of amorphous nature, to low density poly(ethylene)/isotactic poly(propylene) (80/20) blend is demonstrated. This effect is expressed by the major improvement of mechanical properties of ternary blends as examined at a macroscopic size scale by means of tensile measurements. The structure investigation also reveals a clear dependence of the morphology on adding ethylene-copropylene polymer. Both the nature and the content of ethylene-co-propylene polymer affect structure and properties. It is further demonstrated that the extent of improvement in mechanical properties is to be related to the molecular details of the compatibilizer. Combination of high molecular weight and high ethylene content is appropriate for the studied system where the poly(ethylene) plays the role of matrix. A new way to characterize semicrystalline systems by means of Brillouin spectroscopy is presented in this study. By this method based on inelastic light scattering, we were able to measure the high frequency elastic constant (c11) of the two microphases in the case where the spherulites size is exhibit size larger than the size of the probing phonon wavelength. In this considered case, the sample film is inhomogeneous over the relevant length scales and there is an access to the transverse phonon in the crystalline phase yielding the elastic constant c44 as well. Isotactic poly(propylene) is well suited for this type of investigation since its morphology can be tailored through different thermal treatment from the melt. Two distinctly different types of films were used; quenched (low crystallinity) and annealed (high crystallinity). The Brillouin scattering data are discussed with respect to the spherulites size, lamellae thickness, long period, crystallinity degree and well documented by AFM images. The structure and the properties of isotactic poly(propylene) matrix modified by inorganic layered silicate, montmorillonite, are discussed with respect to the clay content. Isotactic poly(propylene)-graft-maleic anhydride was used as compatibilizer. It is clearly demonstrated that the property enhancement is largely due to the ability of layered silicate to exfoliate. The intimate dispersion of the nanometer-thick silicate result from a delicate balance of the content ratio between the isotactic poly(propylene)-graft-maleic anhydride compatibilizer and the inorganic clay.

Single polymers at surfaces: adsorption and detachment

This thesis is concerned with the adsorption and detachment of polymers at planar, rigid surfaces. We have carried out a systematic investigation of adsorption of polymers using analytical techniques as well as Monte Carlo simulations with a coarse grained off-lattice bead spring model. The investigation was carried out in three stages. In the first stage the adsorption of a single multiblock AB copolymer on a solid surface was investigated by means of simulations and scaling analysis. It was shown that the problem could be mapped onto an effective homopolymer problem. Our main result was the phase diagram of regular multiblock copolymers which shows an increase in the critical adsorption potential of the substrate with decreasing size of blocks. We also considered the adsorption of random copolymers which was found to be well described within the annealed disorder approximation. In the next phase, we studied the adsorption kinetics of a single polymer on a flat, structureless surface in the regime of strong physisorption. The idea of a ’stem-flower’ polymer conformation and the mechanism of ’zipping’ during the adsorption process were used to derive a Fokker-Planck equation with reflecting boundary conditions for the time dependent probability distribution function (PDF) of the number of adsorbed monomers. The numerical solution of the time-dependent PDF obtained from a discrete set of coupled differential equations were shown to be in perfect agreement with Monte Carlo simulation results. Finally we studied force induced desorption of a polymer chain adsorbed on an attractive surface. We approached the problem within the framework of two different statistical ensembles; (i) by keeping the pulling force fixed while measuring the position of the polymer chain end, and (ii) by measuring the force necessary to keep the chain end at fixed distance above the adsorbing plane. In the first case we treated the problem within the framework of the Grand Canonical Ensemble approach and derived analytic expressions for the various conformational building blocks, characterizing the structure of an adsorbed linear polymer chain, subject to pulling force of fixed strength. The main result was the phase diagram of a polymer chain under pulling. We demonstrated a novel first order phase transformation which is dichotomic i.e. phase coexistence is not possible. In the second case, we carried out our study in the “fixed height” statistical ensemble where one measures the fluctuating force, exerted by the chain on the last monomer when a chain end is kept fixed at height h over the solid plane at different adsorption strength ε. The phase diagram in the h − ε plane was calculated both analytically and by Monte Carlo simulations. We demonstrated that in the vicinity of the polymer desorption transition a number of properties like fluctuations and probability distribution of various quantities behave differently, if h rather than the force, f, is used as an independent control parameter.

A soft-tetramer model for diblock copolymer melts: structure formation and geometric characterization

The ability of block copolymers to spontaneously self-assemble into a variety of ordered nano-structures not only makes them a scientifically interesting system for the investigation of order-disorder phase transitions, but also offers a wide range of nano-technological applications. The architecture of a diblock is the most simple among the block copolymer systems, hence it is often used as a model system in both experiment and theory. We introduce a new soft-tetramer model for efficient computer simulations of diblock copolymer melts. The instantaneous non-spherical shape of polymer chains in molten state is incorporated by modeling each of the two blocks as two soft spheres. The interactions between the spheres are modeled in a way that the diblock melt tends to microphase separate with decreasing temperature. Using Monte Carlo simulations, we determine the equilibrium structures at variable values of the two relevant control parameters, the diblock composition and the incompatibility of unlike components. The simplicity of the model allows us to scan the control parameter space in a completeness that has not been reached in previous molecular simulations.The resulting phase diagram shows clear similarities with the phase diagram found in experiments. Moreover, we show that structural details of block copolymer chains can be reproduced by our simple model.We develop a novel method for the identification of the observed diblock copolymer mesophases that formalizes the usual approach of direct visual observation,using the characteristic geometry of the structures. A cluster analysis algorithm is used to determine clusters of each component of the diblock, and the number and shape of the clusters can be used to determine the mesophase.We also employ methods from integral geometry for the identification of mesophases and compare their usefulness to the cluster analysis approach.To probe the properties of our model in confinement, we perform molecular dynamics simulations of atomistic polyethylene melts confined between graphite surfaces. The results from these simulations are used as an input for an iterative coarse-graining procedure that yields a surface interaction potential for the soft-tetramer model. Using the interaction potential derived in that way, we perform an initial study on the behavior of the soft-tetramer model in confinement. Comparing with experimental studies, we find that our model can reflect basic features of confined diblock copolymer melts.

Hyperbranched polyglycerols as building blocks for complex amphiphilic structures: synthesis, characterization and applications

Among hyperbranched polymers, polyglycerol is one of the most promising and commonly used macromolecules due to its biocompatibility and versatility. However, the synthesis of high molecular weight polyglycerols still involves many intricacies and has only been understood to a limited extent. Furthermore, only few complex structures like star or block copolymers incorporating polyglycerol have been realized so far. Particularly biocompatible block copolymers are considered promising candidates for biomedical applications.rnThe scope of this thesis was the enhancement of the synthetic process leading to polyglycerol derivatives which implies improved molecular weight control for a broad molecular weight range as well as the assembly of more complex structures like amphiphilic block copolymers. Further insight into the relation between reaction solvent, degree of deprotonation during the ring-opening multibranching polymerization of glycidol and the characteristics of the obtained polymers were achieved within the scope of this work. Based on these results, a novel concept for the preparation of hyperbranched polyglycerols with molecular weights up to 20,000 g/mol was developed, applying a two step synthesis pathway. Starting from a partially deprotonated TMP core, low molecular weight hb-PGs were prepared using the known synthetic protocol that has been established since the late 1990ies. In a subsequent reaction sequence, these well defined polymers were used as hyperbranched macroinitiator cores in order to obtain high molecular weight hb-PGs with remarkably low polydispersity (Mw/Mn < 1.8). Molecular weight control was shown to be excellent and undesired low molecular weight side products were absent. Furthermore, the technique of continuous spin fractionation has been discovered as an efficient method for polyglycerol work-up to remove quantitatively residual monomer- and oligomer traces from hb-PG compositions to result in samples with significantly reduced polydispersities. Based on these results the synthesis of amphiphilic block copolymers containing hydrophilic hyperbranched polyglycerol blocks and linear, apolar poly(propylene oxide) blocks has been significantly improved and augmented to hb-PG-b-l-PPO-b-hb-PG ABA block copolymers. The influence of different polyglycerol-based amphiphiles on the fibril formation was studied by Thioflavin T Fluorescence showing remarkable increasing lag times which is promising in order to enhance the stability of this protein. In addition the first synthesis of poly(glyceryl glycerols) (PGG), introducing a new solketyl glycidyl ether monomer (IGG) was shown. It was furthermore demonstrated that core-functional carbosilane wedges allow application in block copolymer synthesis. Bisglycidolized amine functional polymers were successfully employed as macroinitiators for glycidol polymerization. This resulted in the first example of amphiphilic hyperbranched-hyperbranched polymer structures. Finally, it has been shown that the previously reported synthetic pathway to carboxylated hyperbranched polyglycerol polyelectrolytes can also be applied for the amphiphilic linear-hyperbranched block copolymers. These novel biocompatible and highly amphiphilic polyelectrolytes offer great potential for further investigations. rnrn

Radiolabeling of defined polymer architectures with fluorine-18 and iodine-131 for ex vivo and in vivo evaluation : visualization of structure-property relationships

Nuclear medicine imaging techniques such as PET are of increasing relevance in pharmaceutical research being valuable (pre)clinical tools to non-invasively assess drug performance in vivo. Therapeutic drugs, e.g. chemotherapeutics, often suffer from a poor balance between their efficacy and toxicity. Here, polymer based drug delivery systems can modulate the pharmacokinetics of low Mw therapeutics (prolonging blood circulation time, reducing toxic side effects, increasing target site accumulation) and therefore leading to a more efficient therapy. In this regard, poly-N-(2-hydroxypropyl)-methacrylamide (HPMA) constitutes a promising biocompatible polymer. Towards the further development of these structures, non-invasive PET imaging allows insight into structure-property relationships in vivo. This performant tool can guide design optimization towards more effective drug delivery. Hence, versatile radiolabeling strategies need to be developed and establishing 18F- as well as 131I-labeling of diverse HPMA architectures forms the basis for short- as well as long-term in vivo evaluations. By means of the prosthetic group [18F]FETos, 18F-labeling of distinct HPMA polymer architectures (homopolymers, amphiphilic copolymers as well as block copolymers) was successfully accomplished enabling their systematic evaluation in tumor bearing rats. These investigations revealed pronounced differences depending on individual polymer characteristics (molecular weight, amphiphilicity due to incorporated hydrophobic laurylmethacrylate (LMA) segments, architecture) as well as on the studied tumor model. Polymers showed higher uptake for up to 4 h p.i. into Walker 256 tumors vs. AT1 tumors (correlating to a higher cellular uptake in vitro). Highest tumor concentrations were found for amphiphilic HPMA-ran-LMA copolymers in comparison to homopolymers and block copolymers. Notably, the random LMA copolymer P4* (Mw=55 kDa, 25% LMA) exhibited most promising in vivo behavior such as highest blood retention as well as tumor uptake. Further studies concentrated on the influence of PEGylation (‘stealth effect’) in terms of improving drug delivery properties of defined polymeric micelles. Here, [18F]fluoroethylation of distinct PEGylated block copolymers (0%, 1%, 5%, 7%, 11% of incorporated PEG2kDa) enabled to systematically study the impact of PEG incorporation ratio and respective architecture on the in vivo performance. Most strikingly, higher PEG content caused prolonged blood circulation as well as a linear increase in tumor uptake (Walker 256 carcinoma). Due to the structural diversity of potential polymeric carrier systems, further versatile 18F-labeling strategies are needed. Therefore, a prosthetic 18F-labeling approach based on the Cu(I)-catalyzed click reaction was established for HPMA-based polymers, providing incorporation of fluorine-18 under mild conditions and in high yields. On this basis, a preliminary µPET study of a HPMA-based polymer – radiolabeled via the prosthetic group [18F]F-PEG3-N3 – was successfully accomplished. By revealing early pharmacokinetics, 18F-labeling enables to time-efficiently assess the potential of HPMA polymers for efficient drug delivery. Yet, investigating the long-term fate is essential, especially regarding prolonged circulation properties and passive tumor accumulation (EPR effect). Therefore, radiolabeling of diverse HPMA copolymers with the longer-lived isotope iodine-131 was accomplished enabling in vivo evaluation of copolymer P4* over several days. In this study, tumor retention of 131I-P4* could be demonstrated at least over 48h with concurrent blood clearance thereby confirming promising tumor targeting properties of amphiphilic HPMA copolymer systems based on the EPR effect.

Diblock copolymer - nanocrystal hybrids for optoelectronic applications

Small, smaller, nano - it is a milestone in the development of new materials and technologies. Nanoscience is now present in our daily lives: in the car industry with self-cleaning surfaces, in medicine with cancer therapies, even our clothes and cosmetics utilize nanoparticles. The number and variety of applications has been growing fast in recent years, and the possibilities seem almost infinite. Nanoparticles made of inorganic materials have found applications in new electronic technologies, and organic nanomaterials have been added to resins to produce very strong but light weight materials.rnThis work deals with the combination of organic and inorganic materials for the fabrication of new, functional hybrid systems. For that purpose, block copolymers were made with a long, solubility-enhancing and semiconducting block, and a short anchor block. They were synthesized by either RAFT polymerization or Siegrist polycondensation. For the second block, an active ester was grafted on and subsequently reacted with the anchor molecules in a polymer analogue reaction. The resulting block copolymers had different properties; poly(para-phenylene vinylene) showed self-assembly in organic solvents, which resulted in gelling of the solution. The fibers from a diluted solution were visible through microscopy. When polymer chains were attached to TiO2 nanorods, the hybrids could be integrated into polymer fibers. A light-induced charge separation was demonstrated through KPFM. The polymer charged positively and the charge could travel along the fibers for several hundred nanometers. Polymers made via RAFT polymerization were based on poly(vinyltriphenylamine). Ruthenium chromophores which carried anchor groups were attached to the second block. These novel block copolymers were then attached to ZnO nanorods. A light-induced charge separation was also demonstrated in this system. The ability to disperse inorganic nanoparticles within the film is another advantage of these block copolymers. This was shown with the example of CdSe tetrapods. Poly(vinyltriphenylamine dimer) with disulfide anchor groups was attached to CdSe tetrapods. These four-armed nanoparticles are supposed to show very high charge transport. A polymer without anchor groups was also mixed with the tetrapods in order to investigate the influence of the anchor groups. It was shown that without them no good films were formed and the tetrapods aggregated heavily in the samples. Additionally, a large difference in the film qualities and the aggregation of the tetrapods was found in the sample of the polymer with anchor groups, dependent on the tetrapod arm length and the polymer loading. These systems are very interesting for hybrid solar cells. This work also illustrates similar systems with quantum dots. The influence of the energy level of the polymer on the hole transport from the polymer to the quantum dots, as well as on the efficiency of QLEDs was studied. For this purpose two different polymers were synthesized with different HOMO levels. It was clearly shown that the polymer with the adjusted lower HOMO level had a better hole injection to the quantum dots, which resulted in more efficient light emitting diodes.rnThese systems all have in common the fact that novel, and specially designed polymers, were attached to inorganic nanocrystals. All of these hybrid materials show fascinating properties, and are helpful in the research of new materials for optoelectronic applications.

Random lattice models

This thesis deals with three different physical models, where each model involves a random component which is linked to a cubic lattice. First, a model is studied, which is used in numerical calculations of Quantum Chromodynamics.In these calculations random gauge-fields are distributed on the bonds of the lattice. The formulation of the model is fitted into the mathematical framework of ergodic operator families. We prove, that for small coupling constants, the ergodicity of the underlying probability measure is indeed ensured and that the integrated density of states of the Wilson-Dirac operator exists. The physical situations treated in the next two chapters are more similar to one another. In both cases the principle idea is to study a fermion system in a cubic crystal with impurities, that are modeled by a random potential located at the lattice sites. In the second model we apply the Hartree-Fock approximation to such a system. For the case of reduced Hartree-Fock theory at positive temperatures and a fixed chemical potential we consider the limit of an infinite system. In that case we show the existence and uniqueness of minimizers of the Hartree-Fock functional. In the third model we formulate the fermion system algebraically via C*-algebras. The question imposed here is to calculate the heat production of the system under the influence of an outer electromagnetic field. We show that the heat production corresponds exactly to what is empirically predicted by Joule's law in the regime of linear response.

Functional polymer based nanoparticles : development of defined complex structures as basis for in-vitro and in-vivo applications

In Rahmen der vorliegenden Arbeit wurde ein neuartiger Zugang zu einer Vielzahl von Polymerstrukturen auf Basis des klinisch zugelassenen Polymers Poly(N-(2-Hydroxypropyl)-methacrylamide) (PHPMA) entwickelt. Der synthetische Zugang beruht zum einen auf der Verwendung von Reaktivesterpolymeren und zum anderen auf der Reversible Addition Fragmentation Chain Transfer (RAFT) Polymerisationsmethode. Diese Form einer kontrollierten radikalischen Polymerisation ermöglichte es, neben der Synthese von besser definierten Homopolymeren auch statistische und Blockcopolymere herzustellen. Die Reaktivesterpolymere können durch einfache Aminolyse in HPMA-basierte Systeme überführt werden. Somit können sie als eine vielversprechende Basis zur Synthese von umfangreichen Polymerbibliotheken angesehen werden. Die hergestellten Polymere kombinieren verschiedene Funktionalitäten bei konstantem Polymerisationsgrad. Dies ermöglicht eine Optimierung auf eine gezielte Anwendung hin ohne den Parameter der Kettenlänge zu verändern.rnIm weiteren war es durch Verwendung der RAFT Polymerisation möglich partiell bioabbaubare Blockcopolymere auf Basis von Polylactiden und HPMA herzustellen, in dem ein Kettentransferreagenz (CTA) an ein wohl definiertes Polylactid Homopolymer gekoppelt wurde. Diese Strukturen wurden in ihrer Zusammensetzung variiert und mit Erkennungsstrukturen (Folaten) und markierenden Elementen (Fluoreszenzfarbstoffe und +-emittierenden Radionukleide) versehen und im weiteren in vitro und in vivo evaluiert.rnAuf Grund dieser Errungenschaften war es möglich den Einfluss der Polymermikrostruktur auf das Aggregationsverhalten hin mittel Lichtstreuung und Fluoreszenzkorrelationsspektroskopie zu untersuchen. Es konnte gezeigt werden, dass erst diese Informationen über die Überstrukturbildung die Kinetik der Zellaufnahme erklären können. Somit wurde die wichtige Rolle von Strukturwirkungsbeziehungen nachgewiesen.rnSomit konnte neben der Synthese, Charakterisierung und ersten biologischen Evaluierungen ein Beitrag zum besseres Verständnis zur Interaktion von polymeren Partikeln mit biologischen Systemen geleistet werden.

Non-aqueous dispersions of particles and their applications

In the current work, three studies about non-aqueous dispersions of particles were carried out by using an amphiphilic block copolymer poly(isoprene)-block-poly(methyl methacrylate) (PI-b-PMMA) as stabilizer:rn1. Dispersions of polyurethane and polyurea porous particles for polymer compositesrn2. Dispersions of PMMA and PU particles with PDI dye for study of Single Molecule Spectroscopy Detectionrn3. Dispersions of graphene nanosheets for polymer compositesrnrnIn the first study, highly porous polyurethane and polyurea particles were prepared in a non-aqueous emulsion. The preparation of porous particles consisted of two parts: At first, a system was developed where the emulsion had high stability for the polymerization among diisocyanate, diol and water. In the second part, porous particles were prepared by using two methods fission/fusion and combination by which highly porous particles were obtained. In this study, the applications of porous particles were also investigated where polyurethane particles were tested as filling material for polymer composites and as catalyst carrier for polyethylene polymerization. rnrnIn the second study, PMMA and PU particles from one non-aqueous emulsion were investigated via single molecule fluorescence detection. At first the particles were loaded with PDI dye, which were detected by fluorescence microscopy. The distribution and orientation of the PDI molecules in the particles were successfully observed by Single Molecule Fluorescence Detection. The molecules were homogenously distributed inside of the particles. In addition they had random orientation, meaning that no aggregations of dye molecules were formed. With the results, it could be supposed that the polymer chains were also homogenously distributed in the particles, and that the conformation was relatively flexible. rnrnIn the third part of the study, graphene nanosheets with high surface area were dispersed in an organic solvent with low boiling point and low toxicity, THF, stabilized with a block copolymer PI-b-PMMA. The dispersion was used to prepare polymer composites. It was shown that the modified graphene nanosheets had good compatibility with the PS and PMMA matrices. rn

A photophysical study of excited state dynamics in donor-acceptor copolymer photovoltaic blends

This thesis deals with the investigation of charge generation and recombination processes in three different polymer:fullerene photovoltaic blends by means of ultrafast time-resolved optical spectroscopy. The first donor polymer, namely poly[N-11"-henicosanyl-2,7-carbazole-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (PCDTBT), is a mid-bandgap polymer, the other two materials are the low-bandgap donor polymers poly[2,6-(4,4-bis-(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b']-dithiophene)-alt-4,7-(2,1,3-benzothiadiazole) (PCPDTBT) and poly[(4,4'-bis(2-ethylhexyl)dithieno[3,2-b:2',3'-d]silole)-2,6-diyl-alt-(2,1,3-benzothiadiazole)-4,7-diyl] (PSBTBT). Despite their broader absorption, the low-bandgap polymers do not show enhanced photovoltaic efficiencies compared to the mid-bandgap system.rnrnTransient absorption spectroscopy revealed that energetic disorder plays an important role in the photophysics of PCDTBT, and that in a blend with PCBM geminate losses are small. The photophysics of the low-bandgap system PCPDTBT were strongly altered by adding a high boiling point cosolvent to the polymer:fullerene blend due to a partial demixing of the materials. We observed an increase in device performance together with a reduction of geminate recombination upon addition of the cosolvent. By applying model-free multi-variate curve resolution to the spectroscopic data, we found that fast non-geminate recombination due to polymer triplet state formation is a limiting loss channel in the low-bandgap material system PCPDTBT, whereas in PSBTBT triplet formation has a smaller impact on device performance, and thus higher efficiencies are obtained.rn