Nanoscopic studies of conjugated polymer blends by (electric) scanning probe microscopy

Conjugated polymers and conjugated polymer blends have attracted great interest due to their potential applications in biosensors and organic electronics. The sub-100 nm morphology of these materials is known to heavily influence their electromechanical properties and the performance of devices they are part of. Electromechanical properties include charge injection, transport, recombination, and trapping, the phase behavior and the mechanical robustness of polymers and blends. Electrical scanning probe microscopy techniques are ideal tools to measure simultaneously electric (conductivity and surface potential) and dielectric (dielectric constant) properties, surface morphology, and mechanical properties of thin films of conjugated polymers and their blends.rnIn this thesis, I first present a combined topography, Kelvin probe force microscopy (KPFM), and scanning conductive torsion mode microscopy (SCTMM) study on a gold/polystyrene model system. This system is a mimic for conjugated polymer blends where conductive domains (gold nanoparticles) are embedded in a non-conductive matrix (polystyrene film), like for polypyrrole:polystyrene sulfonate (PPy:PSS), and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS). I controlled the nanoscale morphology of the model by varying the distribution of gold nanoparticles in the polystyrene films. I studied the influence of different morphologies on the surface potential measured by KPFM and on the conductivity measured by SCTMM. By the knowledge I gained from analyzing the data of the model system I was able to predict the nanostructure of a homemade PPy:PSS blend.rnThe morphologic, electric, and dielectric properties of water based conjugated polymer blends, e.g. PPy:PSS or PEDOT:PSS, are known to be influenced by their water content. These properties also influence the macroscopic performance when the polymer blends are employed in a device. In the second part I therefore present an in situ humidity-dependence study on PPy:PSS films spin-coated and drop-coated on hydrophobic highly ordered pyrolytic graphite substrates by KPFM. I additionally used a particular KPFM mode that detects the second harmonic electrostatic force. With this, I obtained images of dielectric constants of samples. Upon increasing relative humidity, the surface morphology and composition of the films changed. I also observed that relative humidity affected thermally unannealed and annealed PPy:PSS films differently. rnThe conductivity of a conjugated polymer may change once it is embedded in a non-conductive matrix, like for PPy embedded in PSS. To measure the conductivity of single conjugated polymer particles, in the third part, I present a direct method based on microscopic four-point probes. I started with metal core-shell and metal bulk particles as models, and measured their conductivities. The study could be extended to measure conductivity of single PPy particles (core-shell and bulk) with a diameter of a few micrometers.

Charge generation, transport and recombination in organic solar cells

This thesis presents a study of the charge generation, transport, and recombination processes in organic solar cells performed with time-resolved experimental techniques. Organic solar cells based on polymers can be solution-processed on large areas and thus promise to become an inexpensive source of renewable energy. Despite significant improvements of the power conversion efficiency over the last decade, the fundamental working principles of organic solar cells are still not fully understood. It is the aim of this thesis to clarify the role of different performance limiting processes in organic solar cells and to correlate them with the molecular structure of the studied materials, i.e. poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl C61 butyric acid methyl ester (PCBM). By combining time-of-flight charge transport measurements, transient absorption spectroscopy, a newly developed experimental technique called time delayed double pulse experiment and drift-diffusion simulations a comprehensive analysis of the working principles of P3HT:PCBM solar cells could be performed. It was found that the molecular structure of P3HT (i.e. the regioregularity) has a pronounced influence on the morphology of thin films of pristine P3HT and of blends of P3HT with PCBM. This morphology in turn affected the charge transport properties as well as the charge generation and recombination kinetics. Well-ordered regioregular P3HT was found to be characterized by a high charge carrier mobility, efficient charge generation and low but field-dependent (non-geminate) recombination. Importantly, the charge generation yield was found to be independent of temperature and applied electric field as opposed to the expectations of the Onsager-Braun model that is commonly applied to describe the temperature and field dependence of charge generation in organic solar cells. These properties resulted in a reasonably good power conversion efficiency. In contrast to this, amorphous regiorandom P3HT was found to show poor charge generation, transport and recombination properties that combine to a much lower power conversion efficiency.

Investigation of P3HT PCBM particle-based solar cells

Die Herstellung von Polymer-Solarzellen aus wässriger Phase stellt eine attraktive Alternative zu der konventionellen lösemittelbasierten Formulierung dar. Die Vorteile der aus wässriger Lösung hergestellten Solarzellen liegen besonders in dem umweltschonenden Herstellungsprozess und in der Möglichkeit, druckbare optoelektronische Bauteile zu generieren. Die Prozessierbarkeit von hydrophoben Halbleitern im wässrigen Milieu wird durch die Dispergierung der Materialien, in Form von Nanopartikeln, erreicht. Der Transfer der Halbleiter in eine Dispersion erfolgt über die Lösemittelverdampfungsmethode. Die Idee der Verwendung von partikelbasierte Solarzellen wurde bereits umgesetzt, allerdings blieben eine genaue Charakterisierung der Partikel sowie ein umfassendes Verständnis des gesamten Fabrikationsvorgangs aus. Deshalb besteht das Ziel dieser Arbeit darin, einen detaillierten Einblick in den Herstellungsprozess von partikelbasierten Solarzellen zu erlangen, mögliche Schwächen aufzudecken, diese zu beseitigen, um so zukünftige Anwendungen zu verbessern. Zur Herstellung von Solarzellen aus wässrigen Dispersionen wurde Poly(3-hexylthiophen-2,5-diyl)/[6,6]-Phenyl-C61-Buttersäure-Methylester (P3HT/PCBM) als Donor/Akzeptor-System verwendet. Die Kernpunkte der Untersuchungen richteten sich zum einen die auf Partikelmorphologie und zum anderen auf die Generierung einer geeigneten Partikelschicht. Beide Parameter haben Auswirkungen auf die Solarzelleneffizienz. Die Morphologie wurde sowohl spektroskopisch über Photolumineszenz-Messungen, als auch visuell mittels Elektronenmikroskopie ermittelt. Auf diese Weise konnte die Partikelmorphologie vollständig aufgeklärt werden, wobei Parallelen zu der Struktur von lösemittelbasierten Solarzellen gefunden wurden. Zudem wurde eine Abhängigkeit der Morphologie von der Präparationstemperatur beobachtet, was eine einfache Steuerung der Partikelstruktur ermöglicht. Im Zuge der Partikelschichtausbildung wurden direkte sowie grenzflächenvermittelnde Beschichtungsmethoden herangezogen. Von diesen Techniken hatte sich aber nur die Rotationsbeschichtung als brauchbare Methode erwiesen, Partikel aus der Dispersion in einen homogenen Film zu überführen. Des Weiteren stand die Aufarbeitung der Partikelschicht durch Ethanol-Waschung und thermische Behandlung im Fokus dieser Arbeit. Beide Maßnahmen wirkten sich positiv auf die Effizienz der Solarzellen aus und trugen entscheidend zu einer Verbesserung der Zellen bei. Insgesamt liefern die gewonnen Erkenntnisse einen detaillierten Überblick über die Herausforderungen, welche bei dem Einsatz von wasserbasierten Dispersionen auftreten. Die Anforderungen partikelbasierter Solarzellen konnten offengelegt werden, dadurch gelang die Herstellung einer Solarzelle mit einer Effizienz von 0.53%. Dieses Ergebnis stellt jedoch noch nicht das Optimum dar und lässt noch Möglichkeiten für Verbesserungen offen.

Synthese und Struktur-Eigenschafts-Beziehungen von Oligo- und Poly(2,5-dipropoxy-1,4-phenylenethinylen)en

Oligomere mit konjugierten pi-Elektronensystemen sind für die Materialwissenschaften von großer Bedeutung. Die vielfältigen und umfangreichen Forschungen auf diesem Gebiet gründen im Potenzial dieser Substanzklassen, das im Bereich der Laserfarbstoffe, Leuchtdioden, Photoleiter, optische Schalter oder auch der molekularen Elektronik angesiedelt ist. Zu diesen gehören auch die in dieser Arbeit synthetisierten und untersuchten Phenylenethinylene. Die Herstellung der Oligomere erfolgt nach der Methode von Sonogashira und Hagihara. Dabei wird ein Halogenaren mit einer Alkinkomponente zur Reaktion gebracht. Als Katalysator dient dabei ein Gemisch aus Bis(triphenylphosphin-palladiumdichlorid), Kupfer-(I)-iodid und Triphenylphosphin. Verwendung fanden bei der Synthese zwei Arten von Schutzgruppen. Es handelt sich dabei einerseits um die Trimethylsilyl- und die Triisopropylsilyl-Funktion, die unabhängig voneinander in ein System eingeführt werden und selektiv wieder entfernt werden können. Die zweite Art sind die Halogene Brom und Iod, die aufgrund ihrer Eigenschaft vielmehr als 'dormant group' bezeichnet werden müssen. Eine Ethinylierung führt zunächst zur Substitution des Iod- und anschließend des Bromatoms. Die so erhaltenen Oligomere werden mit verschiedenen spektroskopischen Methoden untersucht. Besonderes Interesse liegt dabei auf der Bestimmung der effektiven Konjugationslänge (EKL). Damit ist es möglich, die Länge des konjugierten Systems zu bestimmen, das für die betreffenden Eigenschaften des entsprechenden Polymers maßgeblich ist. Das nichtlineare optische Verhalten der Oligomere wird mittels der Third-Harmonic-Generation-Methode (THG) gemessen. Die resultierende Größe, die Suszeptibilität 3. Ordnung, gibt Aufschluß über mögliche industrielle Anwendungen.

Synthesis and characterization of novel poly(imino ketone)s via palladium-catalyzed aryl amination

The challenge of the present work was to synthesize and to characterize new classes of N-containing polymers via palladium-catalyzed aryl amination. This work was inspired by a desire to combine the properties of high-performance polymers such as PEKs with those of N-containing conductive polymers such as polyaniline (PANI), poly(aromatic amides) (PAAs), and the ready synthesis of N-containing simple aromatic compound by the Buchwald-Hartwig reaction. Careful investigation of a model reaction was carried out to provide insights into the formation of side products which will have a negative effect upon the molecular weight or upon the materials properties of the desired polymers in the polycondensation reaction. In this thesis, five new different polymer classes namely, poly(imino ketone)s (PIKs), poly(imino acridine)s (PIAcs), poly(imino azobenzene)s (PIAzos), poly(imino fluorenone)s (PIFOs), and poly(imino carbazole)s (PICs) were synthesized and fully characterized by means of 1H-NMR, elemental analysis, UV, FT-IR, X-ray, GPC, TGA, DSC, DMA, and dielectric spectroscopy. To optimize the polycondensation process, the influence of the concentration, temperature, ligands and the reactivity of the halogen containing monomers were investigated. A temperature of 100-165 °C and a concentration of 30-36 % were found to be optimal for the palladium-catalyzed polycondensation to produce polymer with high molecular weight (Mn = 85 900, Mw = 474 500, DP = 126). Four different ligands were used successfully in the Pd-catalyzed process, of which the Pd/BINAP system was found to be the most effective catalyst, producing the highest yield and highest molecular weight polymers. It was found that the reactivity decreases strongly with increasing electronegativity of the halogen atoms, for example better yields, and higher molecular weights were obtained by using dibromo compounds than dichloro compounds while difluoro compounds were totally unreactive. Polymer analogous transformations, such as the protonation reaction of the ring nitrogens in PIAcs, or of the azobenzene groups of PIAzos, the photo and thermal cis-trans-isomerization of PIAzos, and of poly(imino alcohol)s were also studied. The values of the dielectric constants of PIKs at 1 MHz were in the range 2.71-3.08. These low values of the dielectric constant are lower than that of "H Film", a polyimide Kapton film which is one of the most preferred high-performance dielectrics in microelectronic applications having a dielectric constant of 3.5. In addition to the low values of the dielectric constants, PIKs have lower and glass transition temperatures (Tgs) than arimides such as Kapton which may make them more easily processable. Cyclic voltammetry showed that PICs exhibited low oxidation and reduction potentials and their values were shifted to low values with increasing degree of polymerization i.e. with increasing of the carbazole content in backbone of PICs (PIC-7, 0.44, 0.33 V, DP= 37, PIC-5, 0.63, 0.46, DP= 16, respectively).

1-, 2- and 3-dimensional phenylene-based materials for optoelectronic applications

A series of oligo-phenylene dendronised conjugated polymers was prepared. The divergent synthetic approach adopted allowed for the facile synthesis of a range of dendronised monomers from a common intermediate, e.g. first and second generation fluorene. Only the polymerisation of the first generation and alkylarylamine substituted dendronised fluorene monomers yielded high molecular weight materials, attributed to the low solubility of the remaining dendronised monomers. The alkylarylamine substituted dendronised poly(fluorene) was incorporated into an organic light emitting diode (OLED) and exhibited an increased colour stability in air compared to other poly(fluorenes). The concept of dendronisation was extended to poly(fluorenone), a previously insoluble material. The synthesis of the first soluble poly(fluorenone) was achieved by the incorporation of oligo-phenylene dendrons at the 4-position of fluorenone. The dendronisation of fluorenone allowed for a polymer with an Mn of 4.1 x 104 gmol-1 to be prepared. Cyclic voltammetry of the dendronised poly(fluorenone) showed that the electron affinity of the polymer was high and that the polymer is a promising n-type material. A dimer and trimer of indenofluorene (IF) were prepared from the monobromo IF. These oligomers were investigated by 2-dimensional wide angle x-ray spectroscopy (2D-WAXS), polarised optical microscopy (POM) and dielectric spectroscopy, and found to form highly ordered smetic phases. By attaching perylene dye as the end-capper on the IF oligomers, molecules that exhibited efficient Förster energy transfer were obtained. Indenofluorene monoketone, a potential defect structure for IF based OLED’s, was synthesised. The synthesis of this model defect structure allowed for the long wavelength emission in OLED’s to be identified as ketone defects. The long wavelength emission from the indenofluorene monoketone was found to be concentration dependent, and suggests that aggregate formation is occurring. An IF linked hexa-peri-hexabenzocoronene (HBC) dimer was synthesised. The 2D-WAXS images of this HBC dimer demonstrate that the molecule exhibits intercolumnar organisation perpendicular to the extrusion direction. POM images of mixtures of the HBC dimer mixed with an HBC with a low isotropic temperature demonstrated that the HBC dimer is mixing with the isotropic HBC.

Photovoltaics from discotic liquid crystalline HBCs & poly(2,7-carbazole)s

In this study, the use of the discotic liquid crystalline HBCs and conjugated polymers based on 2,7-carbazole were investigated in detail as donor materials in organic bulk-heterojunction solar cells. It has been shown that they perform efficiently in photovoltaic devices in combination with suitable acceptors. The efficiency was found to depend strongly dependent on the morphology of the film. By investigation of a series of donor materials with similar molecular structures based on both discotic molecules and conjugated polymers, a structure-performance relation was established, which is not only instructive for these materials but also serves as a guideline for improved molecular design. For the series of HBCs used in this study, it is found that the device efficiency decreases with increasing length of the alkyl substituents in the HBC. Thus, the derivative with the smallest alkyl mantle, being more crystalline compared to the HBCs with longer alkyl chains, gave the highest EQE of 12%. A large interfacial separation was found in the blend of HBC-C6,2 and PDI, since the crystallization of the acceptor occurred in a solid matrix of HBC. This led to small dispersed organized domains and benefited the charge transport. In contrast, blends of HBC-C10,6/PDI or HBC-C14,10/PDI revealed a rather homogeneous film limiting the percolation pathways due to a mixed phase. For the first time, poly(2,7-carbazole) was incorporated as a donor material in solar cells using PDI as an electron acceptor. The good fit in orbital energy levels and absorption spectra led to high efficiency. This result indicates that conjugated polymers with high band-gap can also be applied as materials to build efficient solar cells if appropriate electron acceptors are chosen. In order to enhance the light absorption ability, new ladder-type polymers based on pentaphenylene and hexaphenylene with one and three nitrogen bridges per repeat unit have been synthesized and characterized. The polymer 2 with three nitrogen bridges showed more red-shifted absorbance and emission and better packing in the solid-state than the analogous polymer 3 with only one nitrogen bridge per monomer unit. An overall efficiency as high as 1.3% under solar light was obtained for the device based on 1 and PDI, compared with 0.7% for the PCz based device. Therefore, the device performance correlates to a large extent with the solar light absorption ability and the lateral distance between conjugated polymer chains. Since the lateral distance is determined by the length and number of attached alkyl side chains, it is possible to assume that these substituents insulate the charge carrier pathways and decrease the device performance. As an additional consequence, the active semiconductor is diluted in the insulating matrix leading to a lower light absorption. This work suggests ways to improve device performance by molecular design, viz. maintaining the HOMO level while bathochromically shifting the absorption by adopting a more rigid ladder-type structure. Also, a high ratio of nitrogen bridges with small alkyl substituents was a desirable feature both in terms of adjusting the absorption and maintaining a low lateral inter-chain separation, which was necessary for obtaining high current and efficiency values.

Synthesis, characterization and chemical modification of a cationic polyelectrolyte poly(methylene amine)

Polyamine polymers have attracted attention due to their ability to demonstrate pH dependent cationic nature and presence of highly reactive pendant amino groups. These amino groups make them suitable for a host of applications through cross-linking and derivatization. As a result the end use application of a polyamine is largely driven by the number of amino groups and the way they are attached to the polymer backbone. Thus, this piece of work describes the synthesis and investigation of properties of a novel aliphatic polyamine, poly(methylene amine); that carries maximum number of amino group on its backbone. The target polymer, poly(methylene amine); was synthesized via two major steps viz.1.synthesis of precursor polymers of poly(methylene amine) and 2. Hydrolysis of the precursor polymers to obtain poly(methylene amine). The precursor polymers poly (1,3-diacetylimidazole-2-one)(6) and poly(1,3-diformyldihydroimidazol-2-one)(7) were synthesized via radical polymerization of their respective monomers. The monomers were polymerized in bulk as well as in solution at different reaction conditions. The maximum molecular weights were achieved by polymerizing the monomers in bulk (Mn = 6.5 x 104 g/mol and Mw = 2.13 x 105 g/mol) of 6. The precursor polymers were hydrolyzed under strong reaction conditions in ethanol in presence of NaOH, LiCl at 170°C to yield poly(methylene amine). The process of hydrolysis was monitored by IR spectroscopy. The solution properties of poly(methylene amine) and its hydrochloride were investigated by viscosimetry and light scattering. The reduced viscosity of poly (methylene amine) hydrochloride as a function of polymer concentration demonstrated a behavior typical of cationic polyelectrolyte. With decrease in polymer concentration the reduced viscosity of poly(methylene amine) hydrochloride increased gradually. The dynamic light scattering studies also revealed behaviors of a polyelectrolyte. Poly(methylene amine) was reacted with electrophiles to yield novel materials. While the attachment of alkyl group onto the nitrogen would increase nucleophilicity, it would also impose steric hindrance. As a result the degree of substitution on poly(methylene amine) would be governed by both the factors. Therefore, few model reactions with electrophiles were performed on polvinylamine under similar reaction conditions in order to make a comparative evaluation. It was found that under similar reaction conditions the degree of substitution was higher in case of polyvinylamine in comparison with poly (methylene amine).This shows that the steric hindrance outweighs nucleophilicity while deciding degree of substitution of electrophiles on poly(methylene amine). The modification was further extended to its use as an initiator for ring opening polymerization of benzyloxy protected N-carboxyanhydride of z-Lysine. The resulting polymer had an interesting brush like architecture. The solid state morphology of this polymer was investigated by SAXS. The 2D-WAXS diffractograms revealed hexagonal morphology of peptide segments without formation of alpha helices.

Assessing the role of sCYLD and Bcl-3 in immune regulation

CYLD is a deubiquitinating enzyme, which negatively regulates NF-κB signaling by removing Lys63-linked polyubiquitin chains from its substrates. In mice, there are two variants of CYLD: full-length CYLD (FL-CYLD) and its short splice variant sCYLD. sCYLD lacks the NEMO and TRAF2 binding sites and CYLDex7/8 mice, which have been generated in our laboratory, overexpress sCYLD in the absence of the full length transcript. In this thesis, we show that bone marrow-derived macrophages (BMDCs) overexpressing sCYLD display a hyperactive phenotype. They have increased levels of the inflammatory cytokines IL-6 and TNFα, have exaggerated stimulatory capacity and fail to induce tolerance in in vivo experiments. CYLDex7/8 BMDCs have increased levels of nuclear Bcl-3, which we could show to be directly induced by sCYLD expression. NF-κB signaling was markedly upregulated in CYLDex7/8 BMDCs.rnBcl-3 overexpressing BMDCs with normal CYLD expression, however, were not hyperactive, suggesting that Bcl-3 overexpression is not sufficient for causing the observed phenotype. Taken together we propose a model in which the exclusive overexpression of sCYLD with high nuclear levels of Bcl-3 in BMDCs is accompanied by an increased NF-κB activation, resulting in a hyperactive phenotype.rnWe further analyzed macrophages overexpressing sCYLD using the LysMcre CyldFL/FL strain, but could not detect differences in activation marker expression, cytokine secretion or iNOS production. LysMcre CyldFL/FL mice immunized with MOG35-55 peptide showed a more severe course of experimental autoimmune encephalomyelitis (EAE), which could not be explained by enhanced levels of MHC class II on CNS-resident macrophages and microglia or increased T cell infiltration.rnMice overexpressing Bcl-3 in T cells develop spontaneous colitis. They have less peripheral memory/effector T cells and less Th1 cells, whereas Th17 numbers are normal. Naïve T cells overexpressing Bcl-3 show defects in in vitro differentiation to the Th1 or Th17 fate. CD4+ T cells overexpressing Bcl-3 show enhanced survival capacity in in vitro culture, but have a defect in proliferative capacity when stimulated in vitro or when adoptively transferred into lymphopenic hosts.

Synthese und Charakterisierung zylindrischer Poly(2-oxazolin)bürsten als Nanocarrier für Drug Delivery Systeme

Inspiriert durch natürlich vorkommende Peptide, sind Poly(2-oxazoline) vielversprechende Kandidaten für Anwendungen in Bereichen des kontrollierten Wirkstoff- bzw. Gentransportes, wie die moderne Biomedizin dies fordert. Da Polyoxazoline als strukturisomere Amide von natürlichen Polypeptiden aufgefasst werden können, zeigen diese synthetischen Polymere in direktem Vergleich erhebliche Vorteile etwa hinsichtlich Zytotoxizät und Effizienz, was wesentlich dazu beitragen kann, aktuelle Hürden biomedizinischer Fragestellungen hinsichtlich Transport und Targeting zu überwinden. Darüber hinaus sollten zylindrische Polymerbürsten aufgrund ihrer molekularen, architekturbedingten Formanisotropie und jüngsten Ergebnissen insbesondere zur formabhängigen Endozytose sehr aussichtsreiche Kandidaten für den Einsatz zum Wirkstofftransport sein.rnrnDie vorliegende Arbeit widmete sich deshalb der Synthese und Charakterisierung von biokompatiblen zylindrischen Poly(2-oxazolin)bürsten als potentielle Nanotransporter von Wirkstoffen, Biomolekülen oder genetischem Material. Als Monomer wurde zunächst 2-Isopropyloxazolin gewählt, da das Polymer eine Phasenübergangstemperatur von 37 °C besitzt, was für Konjugatsynthesen wie auch diverse biomedizinische Applikationen interessant sein kann. Durch terminierende Methacrylamid Funktionalisierung der lebenden kationischen Oxazolinpolymerisation bzw. nachfolgende Endgruppen Transferreaktionen sind Makromonomere im Bereich 1000-5000 g/mol zugänglich. Erstmals gelang es so 2-Oxazolin basierte, hochmolekulare zylindrische Bürsten mit Konturlängen im Bereich von 250 nm mittels „Grafting Through“ Technik in freier radikalischer Polymerisation herzustellen.rnrnAusgehend von der entwickelten Syntheseroute konnten so neben Homo- und Blockcopolymerbürsten von 2-Ethyl-2-oxazolin und 2-Isopropyl-2-oxazolin auch Bürstenmoleküle aus statistischen Copolymeren von 2-Ethyl-2-oxazolin und unsubstituiertem 2-Oxazolin hergestellt werden. Während letztere die Einführung kationischer Gruppen durch selektivere Abspaltmethoden der Formylreste erlauben und so etwa DNA/RNA Komplexierungen ermöglichen können, bietet andererseits der in dieser Arbeit erstmalig demonstrierte Einsatz Azid-funktionalisierter Initiatoren zur kationischen Oxazolinpolymerisation unter Beibehaltung aller anderen sonstigen Reaktionsschritte auch die Möglichkeit der Synthese Azid-Endgruppen-funktionalisierter Makromonomere. Die „Grafting Through“ Methodik der freien radikalischen Makromonomer Polymerisation ist selbst bei diesen funktionalisierten Systemen von großem Vorteil, erlaubt sie auch hier den Zugang zu hochmolekularen Substraten mit einem Pfropfungs- bzw. Funktionalisierungsgrad von 100 %, da jede Seitenkette dieser zylindrischen Bürsten die aussenliegende, und damit sterisch leichter zugängliche funktionale Gruppe trägt. Dabei gelang es die Syntheseroute so zu gestalten, dass es möglich war alle vorgestellten Polymerbürsten mittels statischer und dynamischer Lichtstreuung hinsichtlich absoluter Molmasse und molekularer Dimension zu charakterisieren.rnIn weitereren Reaktionen konnten dann reaktive Fluoreszenzfarbstoffe mit Hilfe kupferfreier 1,3 dipolarerer Addition (kupferfreie „Click-Chemie“) an die Azid-funktionalisierten Polymerbürsten angebunden werden, so dass eine wesentliche Voraussetzung für die Detektion in in vivo und in vitro Experimenten erfüllt werden kann. Darüber hinaus gelingt die quantitative polymeranaloge Umsetzung der Azid- zu Aminogruppen durch eine polymeranalog geführte Reduktion nach Staudinger; damit können an diesen Systemen auch etablierte Konjugationstechniken an Aminogruppen durchgeführt werden. Zudem erlauben die Aminogruppen-haltigen Polymerbürsten durch Protonierung schon bei physiologischem pH die Komplexierung von DNA oder RNA. rnrnErste Lichtstreumessungen in Blutserum zeigen im Falle der kationischen Aminogruppen tragenden Polymerbürsten zwar Aggregation, was aber durch entsprechende Umsetzung nach Konjugation wahrscheinlich unterdrückt werden kann, zeigen doch die entsprechenden Precursorpolymerbürsten mit Azidgruppen in Serum keinerlei Aggregation.rnrnZellaufnahmestudien in dendritische Zellen zeigen nur im Falle einer Azid-funktionalisierten Poly(2-isopropyl-2-oxazolin)bürste eine unspezifische Aufnahme. Die hydrophileren Poly(2-oxazolin)bürsten weise keine unspezifische Aufnahme auf, was eine wichtige Anfoderung für die Verwendung als Polymercarrier in der Krebsimmuntherapie ist.rn

Poly(lactide): from hyperbranched copolyesters to new block copolymers with functional methacrylates

The prologue of this thesis (Chapter 1.0) gives a general overview on lactone based poly(ester) chemistry with a focus on advanced synthetic strategies for ring-opening polymerization, including the emerging field of organo catalysis. This section is followed by a presentation of the state-of the art regarding the two central fields of the thesis: (i) polyfunctional and branched poly(ester)s in Chapter 1.1 as well as (ii) the development of new poly(ester) based block copolymers with functional methacrylates (Chapter 1.2). Chapter 2 deals with the synthesis of new, non-linear poly(ester) structures. In Chapter 2.1, the synthesis of poly(lactide)-based multiarm stars, prepared via a grafting-from method, is described. The hyperbranched poly(ether)-poly(ol) poly(glycerol) is employed as a hydrophilic core molecule. The resulting star block copolymers exhibit potential as phase transfer agents and can stabilize hydrophilic dyes in a hydrophobic environment. In Chapter 2.2, this approach is expanded to poly(glycolide) multiarm star polymers. The problem of the poor solubility of linear poly(glycolide)s in common organic solvents combined with an improvement of the thermal properties has been approached by the reduction of the total chain length. In Chapter 2.3, the first successful synthesis of hyperbranched poly(lactide)s is presented. The ring-opening, multibranching copolymerization of lactide with the “inimer” 5HDON (a hydroxyl-functional lactone monomer) was carefully examined. Besides a precise molecular characterization involving the determination of the degree of branching, we were able to put forward a reaction model for the formation of branching during polymerization. Several innovative approaches to amphiphilic poly(ester)/poly(methacrylate)-based block copolymers are presented in the third part of the thesis (Chapter 3). Block copolymer build-up especially relies on the combination of ring-opening and living radical polymerization. Atom transfer radical polymerization has been successfully combined with lactide ring-opening, using a “double headed” initiator. This strategy allowed for the realization of poly(lactide)-block-poly(2-hydroxyethyl methacrylate) copolymers, which represent promising materials for tissue engineering scaffolds with anti-fouling properties (Chapter 3.1). The two-step/one-pot approach forgoes the use of protecting groups for HEMA by a careful selection of the reaction conditions. A series of potentially biocompatible and partially biodegradable homo- and block copolymers is described in Chapter 3.2. In order to create a block copolymer with a comparably strong hydrophilic character, a new acetal-protected glycerol monomethacrylate monomer (cis-1,3- benzylidene glycerol methacrylate/BGMA) was designed. The hydrophobic poly(BGMA) could be readily transformed into the hydrophilic and water-soluble poly(iso-glycerol methacrylate) (PIGMA) by mild acidic hydrolysis. Block copolymers of PIGMA and poly(lactide) exhibited interesting spherical aggregates in aqueous environment which could be significantly influenced by variation of the poly(lactide)s stereo-structure. In Chapter 3.3, pH-sensitive poly(ethylene glycol)-b-PBGMA copolymers are described. At slightly acidic pH values (pH 4/37°C), they decompose due to a polarity change of the BGMA block caused by progressing acetal cleavage. This stimuli-responsive behavior renders the system highly attractive for the targeted delivery of anti-cancer drugs. In Chapter 3.4, which was realized in cooperation, the concept of biocompatible, amphiphilic poly(lactide) based polymer drug conjugates, was pursued. This was accomplished in the form of fluorescently labeled poly(HPMA)-b-poly(lactide) copolymers. Fluorescence correlation spectroscopy (FCS) of partially biodegradable block copolymer aggregates exhibited fast cellular uptake by human cervix adenocarcinoma cells without showing toxic effects in the examined concentration range (Chapter 4.1). The current state of further projects which will be pursued in future studies is addressed in Chapter 4. This covers the synthesis of biocompatible star block copolymers (Chapter 4.2) and the development of new methacrylate monomers for biomedical applications (Chapters 4.3 and 4.4). Finally, the further investigation of hydroxyl-functional lactones and carbonates which are promising candidates for the synthesis of new hydrophilic linear or hyperbranched biopolymers, is addressed in Chapter 4.5.

Mikrobielle Synthese von Biopolymeren aus der nachwachsenden Rohstoffquelle Weizenstroh

Weizenstroh als erneuerbare Ressource zur Produktion von Biopolymeren und wichtigen Grundchemikalien stellt eine ökologisch sinnvolle Alternative dar. Durch die vom PFI durchgeführte Thermodruckhydrolyse konnte das Weizenstroh und die darin enthaltenen Zucker fast vollständig mobilisiert werden. Ein umfangreiches Screening nach Organismen, welche die Zucker des Weizenstrohs verwerten konnten, ergab, dass einige wenige Stämme zur PHB-Bildung aus Xylose befähigt waren (10 %). Zur PHB-Synthese aus Glucose waren indes ca. doppelt so viele Organismen in der Lage (20 %). Zwei der insgesamt 118 untersuchten Organismen zeigten besonders gute PHB-Bildung sowohl mit Xylose als auch mit Glucose als Substrat. Dabei handelte es sich um die hauseigenen Stämme Bacillus licheniformis KHC 3 und Bacillus megaterium KNaC 2. Nach Enttoxifizierung der hemicellulosischen Fraktion konnte diese als C-Quelle im Mineral Medium eingesetzt werden. Burkholderia sacchari DSM 17165 und Hydrogenophaga pseudoflava DSM 1034, sowie die hauseigenen Isolate Bacillus licheniformis KHC 3 und Bacillus megaterium KNaC 2 wurden für die Synthese von PHB aus der hemicellulosischen Fraktion verwendet. Die Zucker der hemicellulosischen Fraktion (Xylose, Glucose, Arabinose) konnten durch diese Organismen zur PHB-Synthese genutzt werden. Hierbei stellte sich heraus, dass die beiden Bacillus-Stämme besser zur Produktion von PHB aus dem hemicellulosischen Hydrolysat geeignet waren als die Stämme der DSMZ. Die alternative Umsetzung der im hemicellulosischem Hydrolysat enthaltenen Zucker (Xylose, Glucose und Arabinose) in die wichtigen Grundchemikalien Lactat und Acetat konnte durch die Verwendung von heterofermentativen Milchsäurebakterien verwirklicht werden. Die Bildung dieser wichtigen Grundchemikalien stellt eine interessante Alternative zur PHB-Synthese dar. Die Menge an teuren Zusätzen wie Tomatensaft, welcher für das Wachstum der MSB essentiell war, konnte reduziert werden. Die Glucose der zweiten Fraktion des Weizenstrohs, der cellulosischen Fraktion, konnte ebenfalls durch den Einsatz von Mikroorganismen in PHB umgewandelt werden. Kommerzielle Cellulasen der Firma Novozymes konnten große Mengen an Glucose (≥10 g/l) aus der cellulosischen Fraktion freisetzen. Diese freie Glucose wurde mit Hilfe von Cupriavidus necator DSM 545, Cupriavidus necator NCIMB 11599, Bacillus licheniformis KHC 3 und Bacillus megaterium KNaC 2 zu PHB fermentiert. Wie auch beim hemicellulosischen Hydrolysat konnten hier die beiden Bacillus-Stämme die besten Ergebnisse erzielen. Bei ihnen machte die PHB mehr als die Hälfte der Trockenmasse aus. Die Abtrennung des Zielprodukts ohne die Verwendung von umweltschädlichen Lösungsmitteln wurde durch die Lyse der Zielzellen durch eigens isolierte Enzyme aus Streptomyceten verwirklicht. Die Zelllyse durch die Enzyme aus Streptomyces globisporus subsp. caucasius DSM 40814 und Streptomyces albidoflavus DSM 40233 war erfolgreich und zeigte vor allem bei den Bacillen hohe Wirkung (83 % und 99 % Zelllyse). Bei dem Gram-negativen Organismus Cupriavidus necator DSM 428 konnte die anfangs niedrige Zelllyse von 38 % durch Ultraschallbehandlung auf ca. 75 % erhöht werden.

Expanding the scope of poly(ethylene glycol)s for bioconjugation to squaric acid-mediated PEGylation and pH-sensitivity

Poly(ethylene glycol) (PEG) is used in a broad range of applications due to its unique combination of properties and is approved use in formulations for body-care products, edibles and medicine. This thesis aims at the synthesis and characterization of novel heterofunctional PEG structures and the establishment of diethyl squarate as a suitable linker for the covalent attachment to proteins. Chapter 1 is an introduction on the properties and applications of PEG as well as the fascinating chemistry of squaric acid derivatives. In Chapter 1.1, the synthesis and properties of PEG are described, and the versatile applications of PEG derivatives in everyday products are emphasized with a focus on PEG-based pharmaceuticals and nonionic surfactants. This chapter is written in German, as it was published in the German Journal Chemie in unserer Zeit. Chapter 1.2 deals with PEGs major drawbacks, its non-biodegradability, which impedes parenteral administration of PEG conjugates with polyethers exceeding the renal excretion limit, although these would improve blood circulation times and passive tumor targeting. This section gives a comprehensive overview of the cleavable groups that have been implemented in the polyether backbone to tackle this issue as well as the synthetic strategies employed to accomplish this task. Chapter 1.3 briefly summarizes the chemical properties of alkyl squarates and the advantages in protein conjugation chemistry that can be taken from its use as a coupling agent. In Chapter 2, the application of diethyl squarate as a coupling agent in the PEGylation of proteins is illustrated. Chapter 2.1 describes the straightforward synthesis and characterization of squaric acid ethyl ester amido PEGs with terminal hydroxyl functions or methoxy groups. The reactivity and selectivity of theses activated PEGs are explored in kinetic studies on the reactions with different lysine and other amino acid derivatives, followed by 1H NMR spectroscopy. Further, the efficient attachment of the novel PEGs to a model protein, i.e., bovine serum albumin (BSA), demonstrates the usefulness of the new linker for the PEGylation with heterofunctional PEGs. In Chapter 2.3 initial studies on the biocompatibility of polyether/BSA conjugates synthesized by the squaric acid mediated PEGylation are presented. No cytotoxic effects on human umbilical vein endothelial cells exposed to various concentrations of the conjugates were observed in a WST-1 assay. A cell adhesion molecule - enzyme immunosorbent assay did not reveal the expression of E-selectin or ICAM-1, cell adhesion molecules involved in inflammation processes. The focus of Chapter 3 lies on the syntheses of novel heterofunctional PEG structures which are suitable candidates for the squaric acid mediated PEGylation and exhibit superior features compared to established PEGs applied in bioconjugation. Chapter 3.1 describes the synthetic route to well-defined, linear heterobifunctional PEGs carrying a single acid-sensitive moiety either at the initiation site or at a tunable position in the polyether backbone. A universal concept for the implementation of acetal moieties into initiators for the anionic ring-opening polymerization (AROP) of epoxides is presented and proven to grant access to the degradable PEG structures aimed at. The hydrolysis of the heterofunctional PEG with the acetal moiety at the initiating site is followed by 1H NMR spectroscopy in deuterium oxide at different pH. In an exploratory study, the same polymer is attached to BSA via the squarate acid coupling and subsequently cleaved from the conjugate under acidic conditions. Furthermore, the concept for the generation of acetal-modified AROP initiators is demonstrated to be suitable for cholesterol, and the respective amphiphilic cholesteryl-PEG is cleaved at lowered pH. In Chapter 3.2, the straightforward synthesis of α-amino ω2-dihydroxyl star-shaped three-arm PEGs is described. To assure a symmetric length of the hydroxyl-terminated PEG arms, a novel AROP initiator is presented, who’s primary and secondary hydroxyl groups are separated by an acetal moiety. Upon polymerization of ethylene oxide for these functionalities and subsequent cleavage of the acid-labile unit no difference in the degree of polymerization is seen for both polyether fragments.