Method development using ICP-MS and LA-ICP-MS and their application in environmental and material science

Within this PhD thesis several methods were developed and validated which can find applicationare suitable for environmental sample and material science and should be applicable for monitoring of particular radionuclides and the analysis of the chemical composition of construction materials in the frame of ESS project. The study demonstrated that ICP-MS is a powerful analytical technique for ultrasensitive determination of 129I, 90Sr and lanthanides in both artificial and environmental samples such as water and soil. In particular ICP-MS with collision cell allows measuring extremely low isotope ratios of iodine. It was demonstrated that isotope ratios of 129I/127I as low as 10-7 can be measured with an accuracy and precision suitable for distinguishing sample origins. ICP-MS with collision cell, in particular in combination with cool plasma conditions, reduces the influence of isobaric interferences on m/z = 90 and is therefore well-suited for 90Sr analysis in water samples. However, the applied ICP-CC-QMS in this work is limited for the measurement of 90Sr due to the tailing of 88Sr+ and in particular Daly detector noise. Hyphenation of capillary electrophoresis with ICP-MS was shown to resolve atomic ions of all lanthanides and polyatomic interferences. The elimination of polyatomic and isobaric ICP-MS interferences was accomplished without compromising the sensitivity by the use of a high resolution mode as available on ICP-SFMS. Combination of laser ablation with ICP-MS allowed direct micro and local uranium isotope ratio measurements at the ultratrace concentrations on the surface of biological samples. In particular, the application of a cooled laser ablation chamber improves the precision and accuracy of uranium isotopic ratios measurements in comparison to the non-cooled laser ablation chamber by up to one order of magnitude. In order to reduce the quantification problem, a mono gas on-line solution-based calibration was built based on the insertion of a microflow nebulizer DS-5 directly into the laser ablation chamber. A micro local method to determine the lateral element distribution on NiCrAlY-based alloy and coating after oxidation in air was tested and validated. Calibration procedures involving external calibration, quantification by relative sensitivity coefficients (RSCs) and solution-based calibration were investigated. The analytical method was validated by comparison of the LA-ICP-MS results with data acquired by EDX.

Perfluorinated compounds in environmental matrices of Lake Victoria Gulf

ABSTRACT One of the major ecological challenges on Lake Victoria resources is the existence of “hot spots”, caused by human waste, urban runoff, and industrial effluents. The lake is tending towards eutrophication which is attributed to the increasing human population in its watershed. A report of the levels of perfluorooctane sulfonate and perfluorooctanoic acid in environmental matrices of Lake Victoria is presented, and the management implication of perfluorinated compounds and similar potential organic pollutants examined. Two widely consumed and economically important fish species namely Lates niloticus (Nile perch) and Oreochromis niloticus (Nile tilapia) were obtained from Winam gulf of Lake Victoria, Kenya, and analysed for perfluorooctane sulfonate and perfluorooctanoic acid in muscles and liver using liquid chromatography coupled with mass spectroscopy. Variability in the concentrations of perfluorooctanoic acid or perfluorooctane sulfonate in river waters (range perfluorooctanoic acid 0.4 – 96.4 ng/L and perfluorooctane sulfonate < 0.4 – 13.2 ng/L) was higher than for Lake waters (range perfluorooctanoic acid 0.4 – 11.7 ng/L and perfluorooctane sulfonate < 0.4 – 2.5 ng/L respectively). Significant correlations were tested between perfluorinated compounds levels in sediments, fish and water. Wastewater treatment plants and other anthropogenic sources have been identified as significant sources or pathways for the introduction of perfluoroalkyl compounds into Lake Victoria ecosystem. In this study, elevated concentrations of perfluorooctanoic acid and perfluorooctane sulfonate was found in two wastewater treatment plants (WWTPs) in Kisumu, City of Kenya. An alternative analytical method to liquid chromatography/ mass spectroscopy for analysis of perfluorocarboxylic acids in abiotic and biotic matrices where high concentrations are expected is also presented. Derivatisation of the acid group to form a suitable alkyl ester provided a suitable compound for mass spectroscopy detection coupled to gas chromatography instrumental analysis. The acid is esterified by an alkyl halide i.e benzyl bromide as the alkylating agent for Perfluorocarboxylic acids quantification. The study also involved degradability measurements of emerging perfluorinated surfactants substitutes. The stability of the substitutes of perfluorinated surfactants was tested by employing advanced oxidation processes, followed by conventional tests, among them an automated method based on the manometric respirometry test and standardized fix bed bioreactor [FBBR] on perfluorobutane sulfonate (PFBS), a fluoroethylene polymer, fluorosurfactant (Zonyl), two fluoraliphaticesters (NOVEC ™ FC4430 and NOVEC ™ FC4432) and 10-(trifluoromethoxy) decane-sulfonate. Most of these emmerging surfactants are well-established in the market and have been used in several applications as alternatives to PFOS and PFOA based surfactants. The results of this study can be used as pioneer information for further studies on the sources, behaviour and fate of PFOA and PFOS and other related compounds in both abiotic and biota compartments of Lake Victoria and other lakes. Further an overview in degradation of emerging perfluorinated compounds substitutes is presented. Contribution in method development especially for acid group based fluorosurfactants is presented. The data obtained in this study can particularly be considered when formulating policies and management measures for preservation and sustainability of Lake Victoria resources.

Speziation von Neptunium bei der Migration in Tongestein

Die vorliegende Arbeit wurde im Rahmen eines Stipendiums des interdisziplinärenrnGraduiertenkollegs 826 „Spurenanalytik von Elementspezies: Methodenentwicklung und Anwendungen“, gefördert durch die Deutsche Forschungsgemeinschaft (DFG) und das Land Rheinland-Pfalz, angefertigt. Dabei sollten neue Erkenntnisse über die Wechselwirkung zwischen Neptunium und natürlichem Tongestein mit Hinblick auf die Endlagerung wärmeentwickelnder radioaktiver Abfälle in einem geologischen Tiefenlager gewonnen werden. Auf Grund seiner langen Halbwertszeit von mehr als zwei Millionen Jahren wird Np-237 einen signifikanten Anteil an der Radiotoxizität dieser Abfälle nach Lagerzeiten von mehr als 1000 Jahren haben. Np tritt in Lösung unter umweltrelevanten Bedingungen in den Oxidationsstufen +IV und +V auf. Auf Grund der guten Löslichkeit und daher höheren Mobilität ist Np(V) als die gefährlichere Spezies einzustufen. In den Migrationsstudien wurdernOpalinuston (OPA) aus Mont Terri, Schweiz, als natürliches Referenzmaterial verwendet. Der Fokus dieser Arbeit lag dabei auf der Speziation von Np an der Mineraloberfläche mittels synchrotronbasierter Röntgenabsorptionsspektroskopie (EXAFS/XANES).rnDie Wechselwirkung zwischen Np(V) und OPA wurde zunächst in Batch- und Diffusionsexperimenten in Abhängigkeit verschiedener experimenteller Parameter (u.a. pH, Temperatur, Hintergrundelektrolyt, Einfluss von Huminsäure, Konkurrenz mit U(VI), aerobe/anaerobe Bedingungen) untersucht. Die Untersuchung der Np-Speziation erfolgt zum einen an Pulverproben aus Batch-Experimenten unter aeroben und anaeroben Bedingungen, welche mittels EXAFS-Spektroskopie untersucht wurden. Zum anderen wurden ortsaufgelöste μ-XANES-Messungen an Np-Anreicherungen auf OPA-Dünnschliffen und in Diffusionsproben durchgeführt. Durch Kombination der Spektroskopie mit μ-Rötngenfluoreszenzmapping (XRF) und μ-Röntgenbeugung (XRD) konnten zudem Erkenntnisse über die Elementverteilung von Np und anderen im Opalinuston enthaltenen Elementen sowie über kristalline Mineralphasen im Umfeld von Bereichen erhöhter Np-Konzentration erhalten werden.rnSowohl Sorptionsexperimente als auch die spektroskopischen Untersuchungen zeigten eine teilweise Reduktion von Np(V) zu Np(IV) bei der Wechselwirkung mit OPA. Dabei konnte Pyrit als eine der redoxaktiven Phasen identifiziert werden. In diesem Zusammenhang ist die Bildung schwerlöslicher Np(IV)-Spezies mit Hinblick auf die Endlagerung positiv zu bewerten.

Charge-transport simulations in organic semiconductors

In this thesis we have extended the methods for microscopic charge-transport simulations for organic semiconductors. In these materials the weak intermolecular interactions lead to spatially localized charge carriers, and the charge transport occurs as an activated hopping process between diabatic states. In addition to weak electronic couplings between these states, different electrostatic environments in the organic material lead to a broadening of the density of states for the charge energies which limits carrier mobilities.rnThe contributions to the method development includern(i) the derivation of a bimolecular charge-transfer rate,rn(ii) the efficient evaluation of intermolecular (outer-sphere) reorganization energies,rn(iii) the investigation of effects of conformational disorder on intramolecular reorganization energies or internal site energiesrnand (iv) the inclusion of self-consistent polarization interactions for calculation of charge energies.These methods were applied to study charge transport in amorphous phases of small molecules used in the emission layer of organic light emitting diodes (OLED).rnWhen bulky substituents are attached to an aromatic core in order to adjust energy levels or prevent crystallization, a small amount of delocalization of the frontier orbital to the substituents can increase electronic couplings between neighboring molecules. This leads to improved charge-transfer rates and, hence, larger charge-mobility. We therefore suggest using the mesomeric effect (as opposed to the inductive effect) when attaching substituents to aromatic cores, which is necessary for example in deep blue OLEDs, where the energy levels of a host molecule have to be adjusted to those of the emitter.rnFurthermore, the energy landscape for charges in an amorphous phase cannot be predicted by mesoscopic models because they approximate the realistic morphology by a lattice and represent molecular charge distributions in a multipole expansion. The microscopic approach shows that a polarization-induced stabilization of a molecule in its charged and neutral states can lead to large shifts, broadening, and traps in the distribution of charge energies. These results are especially important for multi-component systems (the emission layer of an OLED or the donor-acceptor interface of an organic solar cell), if the change in polarizability upon charging (or excitation in case of energy transport) is different for the components. Thus, the polarizability change upon charging or excitation should be added to the set of molecular parameters essential for understanding charge and energy transport in organic semiconductors.rnWe also studied charge transport in self-assembled systems, where intermolecular packing motives induced by side chains can increase electronic couplings between molecules. This leads to larger charge mobility, which is essential to improve devices such as organic field effect transistors, where low carrier mobilities limit the switching frequency.rnHowever, it is not sufficient to match the average local molecular order induced by the sidernchains (such as the pitch angle between consecutive molecules in a discotic mesophase) with maxima of the electronic couplings.rnIt is also important to make the corresponding distributions as narrow as possible compared to the window determined by the closest minima of thernelectronic couplings. This is especially important in one-dimensional systems, where charge transport is limited by the smallest electronic couplings.rnThe immediate implication for compound design is that the side chains should assist the self-assemblingrnprocess not only via soft entropic interactions, but also via stronger specific interactions, such as hydrogen bonding.rnrnrnrn

Development of a multi-species method by GC-coupling with inductively coupled plasma isotope dilution mass spectrometry for the simultaneous determination of alkylated lead, mercury and tin compounds

An accurate and sensitive species-specific GC-ICP-IDMS (gas chromatography inductively coupled plasma isotope dilution mass spectrometry) method for the determination of trimethyllead and a multi-species-specific GC-ICP-IDMS method for the simultaneous determination of trimethyllead, methylmercury, and butyltins in biological and environmental samples were developed. They allow the determination of corresponding elemental species down to the low ng g-1 range. The developed synthesis scheme for the formation of isotopically labeled Me3206Pb+ can be used for future production of this spike. The novel extraction technique, stir bar sorptive extraction (SBSE), was applied for the first time in connection with species-specific isotope dilution GC-ICP-MS for the determination of trimethyllead, methylmercury and butyltins. The results were compared with liquid-liquid extraction. The developed methods were validated by the analysis of certified reference materials. The liquid-liquid extraction GC-ICP-IDMS method was applied to seafood samples purchased from a supermarket. The methylated lead fraction in these samples, correlated to total lead, varied in a broad range of 0.01-7.6 %. On the contrary, the fraction of methylmercury is much higher, normally in the range of 80-98 %. The highest methylmercury content of up to 12 µg g-1 has been determined in shark samples, an animal which is at the end of the marine food chain, whereas in other seafood samples a MeHg+ content of less than 0.2 µg g-1 was found. Butyltin species could only be determined in samples, where anthropogenic contaminations must be assumed. This explains the observed broad variation of the butylated tin fraction in the range of <0.3-49 % in different seafood samples. Because all isotope-labelled spike compounds, except trimethyllead, are commercially available, the developed multi-species-specific GC-ICP-IDMS method has a high potential in future for routine analysis.

Development of a field method to assess root parasites of woody plants - ecological analyses of the grapevine-phylloxera interaction

The development and the growth of plants is strongly affected by the interactions between roots, rootrnassociated organisms and rhizosphere communities. Methods to assess such interactions are hardly torndevelop particularly in perennial and woody plants, due to their complex root system structure and theirrntemporal change in physiology patterns. In this respect, grape root systems are not investigated veryrnwell. The aim of the present work was the development of a method to assess and predict interactionsrnat the root system of rootstocks (Vitis berlandieri x Vitis riparia) in field. To achieve this aim, grapernphylloxera (Daktulosphaira vitifoliae Fitch, Hemiptera, Aphidoidea) was used as a graperoot parasitizingrnmodel.rnTo develop the methodical approach, a longt-term trial (2006-2009) was arranged on a commercial usedrnvineyard in Geisenheim/Rheingau. All 2 to 8 weeks the top most 20 cm of soil under the foliage wallrnwere investigated and root material was extracted (n=8-10). To include temporal, spatial and cultivarrnspecific root system dynamics, the extracted root material was analyzed digitally on the morphologicalrnproperties. The grape phylloxera population was quantified and characterized visually on base of theirrnlarvalstages (oviparous, non oviparous and winged preliminary stages). Infection patches (nodosities)rnwere characterized visually as well, partly supported by digital root color analyses. Due to the knownrneffects of fungal endophytes on the vitality of grape phylloxera infested grapevines, fungal endophytesrnwere isolated from nodosity and root tissue and characterized (morphotypes) afterwards. Further abioticrnand biotic soil conditions of the vineyards were assessed. The temporal, spatial and cultivar specificrnsensitivity of single parameters were analyzed by omnibus tests (ANOVAs) and adjacent post-hoc tests.rnThe relations between different parameters were analyzed by multiple regression models.rnQuantitative parameters to assess the degeneration of nodosity, the development nodosity attachedrnroots and to differentiate between nodosities and other root swellings in field were developed. Significantrndifferences were shown between root dynamic including parameters and root dynamic ignoringrnparameters. Regarding the description of grape phylloxera population and root system dynamic, thernmethod showed a high temporal, spatial and cultivar specific sensitivity. Further, specific differencesrncould be shown in the frequency of endophyte morphotypes between root and nodosity tissue as wellrnas between cultivars. Degeneration of nodosities as well as nodosity occupation rates could be relatedrnto the calculated abundances of grape phylloxera population. Further ecological questions consideringrngrape root development (e.g. relation between moisture and root development) and grape phylloxerarnpopulation development (e.g. relation between temperature and population structure) could be answeredrnfor field conditions.rnGenerally, the presented work provides an approach to evaluate vitality of grape root systems. Thisrnapproach can be useful, considering the development of control strategies against soilborne pests inrnviticulture (e.g. grape phylloxera, Sorospheara viticola, Roesleria subterranea (Weinm.) Redhaed) as well as considering the evaluation of integrated management systems in viticulture.

Development and application of an analytical method for the determination of total atmospheric biogenic non-methane organic carbon

Ein wesentlicher Anteil an organischem Kohlenstoff, der in der Atmosphäre vorhanden ist, wird als leichtflüchtige organische Verbindungen gefunden. Diese werden überwiegend durch die Biosphäre freigesetzt. Solche biogenen Emissionen haben einen großen Einfluss auf die chemischen und physikalischen Eigenschaften der Atmosphäre, indem sie zur Bildung von bodennahem Ozon und sekundären organischen Aerosolen beitragen. Um die Bildung von bodennahem Ozon und von sekundären organischen Aerosolen besser zu verstehen, ist die technische Fähigkeit zur genauen Messung der Summe dieser flüchtigen organischen Substanzen notwendig. Häufig verwendete Methoden sind nur auf den Nachweis von spezifischen Nicht-Methan-Kohlenwasserstoffverbindungen fokussiert. Die Summe dieser Einzelverbindungen könnte gegebenenfalls aber nur eine Untergrenze an atmosphärischen organischen Kohlenstoffkonzentrationen darstellen, da die verfügbaren Methoden nicht in der Lage sind, alle organischen Verbindungen in der Atmosphäre zu analysieren. Einige Studien sind bekannt, die sich mit der Gesamtkohlenstoffbestimmung von Nicht-Methan-Kohlenwasserstoffverbindung in Luft beschäftigt haben, aber Messungen des gesamten organischen Nicht-Methan-Verbindungsaustauschs zwischen Vegetation und Atmosphäre fehlen. Daher untersuchten wir die Gesamtkohlenstoffbestimmung organische Nicht-Methan-Verbindungen aus biogenen Quellen. Die Bestimmung des organischen Gesamtkohlenstoffs wurde durch Sammeln und Anreichern dieser Verbindungen auf einem festen Adsorptionsmaterial realisiert. Dieser erste Schritt war notwendig, um die stabilen Gase CO, CO2 und CH4 von der organischen Kohlenstofffraktion zu trennen. Die organischen Verbindungen wurden thermisch desorbiert und zu CO2 oxidiert. Das aus der Oxidation entstandene CO2 wurde auf einer weiteren Anreicherungseinheit gesammelt und durch thermische Desorption und anschließende Detektion mit einem Infrarot-Gasanalysator analysiert. Als große Schwierigkeiten identifizierten wir (i) die Abtrennung von CO2 aus der Umgebungsluft von der organischen Kohlenstoffverbindungsfaktion während der Anreicherung sowie (ii) die Widerfindungsraten der verschiedenen Nicht-Methan-Kohlenwasserstoff-verbindungen vom Adsorptionsmaterial, (iii) die Wahl des Katalysators sowie (iiii) auftretende Interferenzen am Detektor des Gesamtkohlenstoffanalysators. Die Wahl eines Pt-Rd Drahts als Katalysator führte zu einem bedeutenden Fortschritt in Bezug auf die korrekte Ermittlung des CO2-Hintergrund-Signals. Dies war notwendig, da CO2 auch in geringen Mengen auf der Adsorptionseinheit während der Anreicherung der leichtflüchtigen organischen Substanzen gesammelt wurde. Katalytische Materialien mit hohen Oberflächen stellten sich als unbrauchbar für diese Anwendung heraus, weil trotz hoher Temperaturen eine CO2-Aufnahme und eine spätere Abgabe durch das Katalysatormaterial beobachtet werden konnte. Die Methode wurde mit verschiedenen leichtflüchtigen organischen Einzelsubstanzen sowie in zwei Pflanzenkammer-Experimenten mit einer Auswahl an VOC-Spezies getestet, die von unterschiedlichen Pflanzen emittiert wurden. Die Pflanzenkammer-messungen wurden durch GC-MS und PTR-MS Messungen begleitet. Außerdem wurden Kalibrationstests mit verschiedenen Einzelsubstanzen aus Permeations-/Diffusionsquellen durchgeführt. Der Gesamtkohlenstoffanalysator konnte den tageszeitlichen Verlauf der Pflanzenemissionen bestätigen. Allerdings konnten Abweichungen für die Mischungsverhältnisse des organischen Gesamtkohlenstoffs von bis zu 50% im Vergleich zu den begleitenden Standardmethoden beobachtet werden.