Poly(p-phenylen)-Derivate für die Anwendung in Leuchtdioden

Zusammenfassung Das 2,7-Polyfluoren (2,7-PF) wurde in neuer Zeit sowohl wegen seiner einfachen Synthese und hohen Fluoreszenzquantenausbeuten als auch seiner chemischen und thermischen Stabilität intensiv untersucht. Leider liegt das Emissionsmaximum von 2,7-PF in einem Bereich, bei dem das menschliche Auge nicht genügend Sensitivität aufweist. Das Leiter-Poly(p-phenylen) (LPPP) besitzt die optimale Wellenlänge. Jedoch zeigt das LPPP wegen seines steifen Rückgrates große Aggregationstendenz im Film auf, wodurch die Emissionsfarbe bathochrom verschoben und die Photolumineszenzquantenausbeute verringert wird. Es ist deshalb wünschenswert, Polymere zu synthetisieren, die eine längerwellige Emissionsbande als 2,7-PF und eine geringere Aggregationstendenz als LPPP 20 besitzen. Eine Reihe neuer blau emittierender Polymere auf der Basis von Indenofluoren- und Fluoren-Bausteinen mit geringer Aggregationstendenz, hoher thermischer und chemischer Stabilität sowie guter Verarbeitbarkeit wurden dargestellt. Die Polymere weisen eine hohe thermische Stabilität auf (Zersetzung ca.: 310 °C) und sind sehr gut löslich in organischen Lösungsmitteln. Das Absorptionsmaximum des 2,8-Polyindenofluoren (2,8-PIF) in Chloroform liegt bei 416 nm, das Emissionsmaximun bei 432 nm. Die Phasenumwandlungstemperatur beim PIF liegt ca. bei 260 °C. Leider zeigen 2,8-PIF Aggregationstendenzen im Film. Um die Aggregation komplett zu unterbinden, wurden Polyphenylene als Seitenketten an das Dibromfluoren angebracht. Anschließend wurde nach Yamamoto polymerisiert. Das dendritnische PF (DPF) weist die gleiche thermische Stabilität wie die PIFs 28 auf (Zersetzung: 340 °C). Das Polymer 62a ist sehr gut löslich in Toluol, Xylol und chlorierten organischen Lösungsmitteln. Die Absorptions- und Emissionsmaxima des DPFs in Lösung (Chloroform) weisen keine Veränderung gegenüber PF auf. Die Emissionsmaxima des DPFs im Film und nach dem Tempern (100 °C, 24 h) zeigen lediglich eine Verschiebung um 8 nm. Eine Aggregatenbande entsteht jedoch nicht. Dies unterstreicht die abschirmende Eigenschaft der dendritischen Substituenten. Durch Copolymerisation lassen sich die Eigenschaften von Polymeren variieren. Um die Aggregationstendenz der PIF-Derivate zu verringern, wurden die entsprechenden Monomere in verschiedenen Verhältnissen copolymerisiert. Durch die Copolymerisation wurde die PL-Quantenausbeute auf 50 % erhöht. Weiterhin wurden Copolymere von Indenofluoren und 9,10-Dibromanthracen, und erschiedenen Perylenen hergestellt, um zu blau, rot und grün emittierenden Polymeren zu gelangen. Alle blau emittierenden Polymeren wurden in Leuchtdioden untersucht. Das DPF und das Copolymer aus Indenofluoren und Anthracene wiesen die besten Eigenschaften hierfür auf.

Noble-metal nanoparticles produced with colloidal lithography: fabrication, optical properties and applications

In this work, metal nanoparticles produced by nanosphere lithography were studied in terms of their optical properties (in connection to their plasmon resonances), their potential application in sensing platforms - for thin layer sensing and bio-recognition events -, and for a particular case (the nanocrescents), for enhanced spectroscopy studies. The general preparation procedures introduced early in 2005 by Shumaker-Parry et al. to produce metallic nanocrescents were extended to give rise to more complex (isolated) structures, and also, by combining colloidal monolayer fabrication and plasma etching techniques, to arrays of them. The fabrication methods presented in this work were extended not only to new shapes or arrangements of particles, but included also a targeted surface tailoring of the substrates and the structures, using different thiol and silane compounds as linkers for further attachment of, i.e. polyelectrolyte layers, which allow for a controlled tailoring of their nanoenvironment. The optical properties of the nanocrescents were studied with conventional transmission spectroscopy; a simple multipole model was adapted to explain their behaviour qualitatively. In terms of applications, the results on thin film sensing using these particles show that the crescents present an interesting mode-dependent sensitivity and spatial extension. Parallel to this, the penetrations depths were modeled with two simplified schemes, obtaining good agreement with theory. The multiple modes of the particles with their characteristic decay lengths and sensitivities represent a major improvement for particle-sensing platforms compared to previous single resonance systems. The nanocrescents were also used to alter the emission properties of fluorophores placed close to them. In this work, green emitting dyes were placed at controlled distances from the structures and excited using a pulsed laser emitting in the near infrared. The fluorescence signal obtained in this manner should be connected to a two-photon processes triggered by these structures; obtaining first insight into plasmon-mediated enhancement phenomena. An even simpler and faster approach to produce plasmonic structures than that for the crescents was tested. Metallic nanodiscs and nanoellipses were produced by means of nanosphere lithography, extending a procedure reported in the literature to new shapes and optical properties. The optical properties of these particles were characterized by extinction spectroscopy and compared to results from the literature. Their major advantage is that they present a polarization-dependent response, like the nanocrescents, but are much simpler to fabricate, and the resonances can be tailored in the visible with relative ease. The sensing capabilities of the metallic nanodiscs were explored in the same manner as for the nanocrescents, meaning their response to thin layers and to bio-recognition events on their surface. The sensitivity of these nanostructures to thin films proved to be lower than that of the crescents, though in the same order of magnitude. Experimental information about the near field extension for the Au nanodiscs of different sizes was also extracted from these measurements. Further resonance-tailoring approaches based on electrochemical deposition of metals on the nanodiscs were explored, as a means of modifying plasmon resonances by changing surface properties of the nanoparticles. First results on these experiments would indicate that the deposition of Ag on Au on a submonolayer coverage level can lead to important blue-shifts in the resonances, which would open a simple way to tailor resonances by changing material properties in a local manner.

Helicity methods in LO and NLO QCD calculations

The goal of this thesis is the acceleration of numerical calculations of QCD observables, both at leading order and next–to–leading order in the coupling constant. In particular, the optimization of helicity and spin summation in the context of VEGAS Monte Carlo algorithms is investigated. In the literature, two such methods are mentioned but without detailed analyses. Only one of these methods can be used at next–to–leading order. This work presents a total of five different methods that replace the helicity sums with a Monte Carlo integration. This integration can be combined with the existing phase space integral, in the hope that this causes less overhead than the complete summation. For three of these methods, an extension to existing subtraction terms is developed which is required to enable next–to–leading order calculations. All methods are analyzed with respect to efficiency, accuracy, and ease of implementation before they are compared with each other. In this process, one method shows clear advantages in relation to all others.

Synthesis and application of stimuli responsive tunable systems based on physical interactions

Novel single step synthetic procedure for hydrophobically modified alkali soluble latexes (HASE) via a miniemulsion-analogous method is presented. This facile method simplifies the copolymerization of the monomers with basically “opposite” character in terms of their hydrophilic/hydrophobic nature, which represent one of the main challenges in water based systems. Considered systems do not represent classical miniemulsions due to a high content of water soluble monomers. However, the polymerization mechanism was found to be rather similar to miniemulsion polymerization process.rnThe influence of the different factors on the system stability has been investigated. The copolymerization behavior studies typically showed strong composition drifts during copolymerization. It was found that the copolymer composition drift can be suppressed via changing the initial monomer ratio.rnThe neutralization behavior of the obtained HASE systems was investigated via potentiometric titration. The rheological behavior of the obtained systems as a function of the different parameters, such as pH, composition (ultrahydrophobe content) and additive type and content has also been investigated.rnDetailed investigation of the storage and loss moduli, damping factor and the crossover frequencies of the samples showed that at the initial stages of the neutralization the systems show microgel-like behavior.rnThe dependence of the rheological properties on the content and the type of the ultrahydrophobe showed that the tuning of the mechanical properties can be easily achieved via minor (few percent) but significant changes in the content of the latter. Besides, changing the hydrophobicity of the ultrahydrophobe via increasing the carbon chain length represents another simple method for achieving the same results.rnThe influence of amphiphilic additives (especially alcohols) on the rheological behavior of the obtained systems has been studied. An analogy was made between micellation of surfactants and the formation of hydrophobic domains between hydrophobic groups of the polymer side chain.rnDilution induced viscosity reduction was investigated in different systems, without or with different amounts or types of the amphiphilic additive. Possibility of the controlled response to dilution was explored. It was concluded that the sensitivity towards dilution can be reduced, and in extreme cases even the increase of the dynamic modulus can be observed, which is of high importance for the setting behavior of the adhesive material.rnIn the last part of this work, the adhesive behavior of the obtained HASE systems was investigated on different substrates (polypropylene and glass) for the standard labeling paper. Wet tack and setting behavior was studied and the trends for possible applications have been evaluated.rnThe novel synthetic procedure, investigation of rheological properties and the possibility of the tuning via additives, investigated in this work create a firm background for the development of the HASE based adhesives as well as rheology modifiers with vast variety of possible applications due to ease of tuning the mechanical and rheological properties of the systems.