Measurement of the elastic electron-proton cross section and separation of the electric and magnetic form factor in the Q 2 range from 0.004 to 1 (GeV/c) 2

The electromagnetic form factors of the proton are fundamental quantities sensitive to the distribution of charge and magnetization inside the proton. Precise knowledge of the form factors, in particular of the charge and magnetization radii provide strong tests for theory in the non-perturbative regime of QCD. However, the existing data at Q^2 below 1 (GeV/c)^2 are not precise enough for a hard test of theoretical predictions.rnrnFor a more precise determination of the form factors, within this work more than 1400 cross sections of the reaction H(e,e′)p were measured at the Mainz Microtron MAMI using the 3-spectrometer-facility of the A1-collaboration. The data were taken in three periods in the years 2006 and 2007 using beam energies of 180, 315, 450, 585, 720 and 855 MeV. They cover the Q^2 region from 0.004 to 1 (GeV/c)^2 with counting rate uncertainties below 0.2% for most of the data points. The relative luminosity of the measurements was determined using one of the spectrometers as a luminosity monitor. The overlapping acceptances of the measurements maximize the internal redundancy of the data and allow, together with several additions to the standard experimental setup, for tight control of systematic uncertainties.rnTo account for the radiative processes, an event generator was developed and implemented in the simulation package of the analysis software which works without peaking approximation by explicitly calculating the Bethe-Heitler and Born Feynman diagrams for each event.rnTo separate the form factors and to determine the radii, the data were analyzed by fitting a wide selection of form factor models directly to the measured cross sections. These fits also determined the absolute normalization of the different data subsets. The validity of this method was tested with extensive simulations. The results were compared to an extraction via the standard Rosenbluth technique.rnrnThe dip structure in G_E that was seen in the analysis of the previous world data shows up in a modified form. When compared to the standard-dipole form factor as a smooth curve, the extracted G_E exhibits a strong change of the slope around 0.1 (GeV/c)^2, and in the magnetic form factor a dip around 0.2 (GeV/c)^2 is found. This may be taken as indications for a pion cloud. For higher Q^2, the fits yield larger values for G_M than previous measurements, in agreement with form factor ratios from recent precise polarized measurements in the Q2 region up to 0.6 (GeV/c)^2.rnrnThe charge and magnetic rms radii are determined as rn⟨r_e⟩=0.879 ± 0.005(stat.) ± 0.004(syst.) ± 0.002(model) ± 0.004(group) fm,rn⟨r_m⟩=0.777 ± 0.013(stat.) ± 0.009(syst.) ± 0.005(model) ± 0.002(group) fm.rnThis charge radius is significantly larger than theoretical predictions and than the radius of the standard dipole. However, it is in agreement with earlier results measured at the Mainz linear accelerator and with determinations from Hydrogen Lamb shift measurements. The extracted magnetic radius is smaller than previous determinations and than the standard-dipole value.

Tracking, b-tagging and measurement of the b-jet production cross section with the ATLAS detector

The Standard Model of elementary particle physics was developed to describe the fundamental particles which constitute matter and the interactions between them. The Large Hadron Collider (LHC) at CERN in Geneva was built to solve some of the remaining open questions in the Standard Model and to explore physics beyond it, by colliding two proton beams at world-record centre-of-mass energies. The ATLAS experiment is designed to reconstruct particles and their decay products originating from these collisions. The precise reconstruction of particle trajectories plays an important role in the identification of particle jets which originate from bottom quarks (b-tagging). This thesis describes the step-wise commissioning of the ATLAS track reconstruction and b-tagging software and one of the first measurements of the b-jet production cross section in pp collisions at sqrt(s)=7 TeV with the ATLAS detector. The performance of the track reconstruction software was studied in great detail, first using data from cosmic ray showers and then collisions at sqrt(s)=900 GeV and 7 TeV. The good understanding of the track reconstruction software allowed a very early deployment of the b-tagging algorithms. First studies of these algorithms and the measurement of the b-tagging efficiency in the data are presented. They agree well with predictions from Monte Carlo simulations. The b-jet production cross section was measured with the 2010 dataset recorded by the ATLAS detector, employing muons in jets to estimate the fraction of b-jets. The measurement is in good agreement with the Standard Model predictions.

Measurement of the inclusive jet cross section in proton-proton collisions at root out s = 7 TeV with the ATLAS detector

The dominant process in hard proton-proton collisions is the production of hadronic jets.rnThese sprays of particles are produced by colored partons, which are struck out of their confinement within the proton.rnPrevious measurements of inclusive jet cross sections have provided valuable information for the determination of parton density functions and allow for stringent tests of perturbative QCD at the highest accessible energies.rnrnThis thesis will present a measurement of inclusive jet cross sections in proton-proton collisions using the ATLAS detector at the LHC at a center-of-mass energy of 7 TeV.rnJets are identified using the anti-kt algorithm and jet radii of R=0.6 and R=0.4.rnThey are calibrated using a dedicated pT and eta dependent jet calibration scheme.rnThe cross sections are measured for 40 GeV < pT <= 1 TeV and |y| < 2.8 in four bins of absolute rapidity, using data recorded in 2010 corresponding to an integrated luminosity of 3 pb^-1.rnThe data is fully corrected for detector effects and compared to theoretical predictions calculated at next-to-leading order including non-perturbative effects.rnThe theoretical predictions are found to agree with data within the experimental and theoretic uncertainties.rnrnThe ratio of cross sections for R=0.4 and R=0.6 is measured, exploiting the significant correlations of the systematic uncertainties, and is compared to recently developed theoretical predictions.rnThe underlying event can be characterized by the amount of transverse momentum per unit rapidity and azimuth, called rhoue.rnUsing analytical approaches to the calculation of non-perturbative corrections to jets, rhoue at the LHC is estimated using the ratio measurement.rnA feasibility study of a combined measurement of rhoue and the average strong coupling in the non-perturbative regime alpha_0 is presented and proposals for future jet measurements at the LHC are made.

Measurement of the e + e - pi + pi - pi + pi - cross section using initial state radiation at BABAR

One of the most precisely measured quantities in particle physics is the magnetic moment of the muon, which describes its coupling to an external magnetic field. It is expressed in form of the anomalous magnetic moment of the muon a_mu=(g_mu-2)/2 and has been determined experimentally with a precision of 0.5 parts per million. The current direct measurement and the theoretical prediction of the standard model differ by more than 3.5 standard deviations. Concerning theory, the contribution of the QED and weak interaction to a_mu can be calculated with very high precision in a perturbative approach.rnAt low energies, however, perturbation theory cannot be used to determine the hadronic contribution a^had_mu. On the other hand, a^had_mu may be derived via a dispersion relation from the sum of measured cross sections of exclusive hadronic reactions. Decreasing the experimental uncertainty on these hadronic cross sections is of utmost importance for an improved standard model prediction of a_mu.rnrnIn addition to traditional energy scan experiments, the method of Initial State Radiation (ISR) is used to measure hadronic cross sections. This approach allows experiments at colliders running at a fixed centre-of-mass energy to access smaller effective energies by studying events which contain a high-energetic photon emitted from the initial electron or positron. Using the technique of ISR, the energy range from threshold up to 4.5GeV can be accessed at Babar.rnrnThe cross section e+e- -> pi+pi- contributes with approximately 70% to the hadronic part of the anomalous magnetic moment of the muon a_mu^had. This important channel has been measured with a precision of better than 1%. Therefore, the leading contribution to the uncertainty of a_mu^had at present stems from the invariant mass region between 1GeV and 2GeV. In this energy range, the channels e+e- -> pi+pi-pi+pi- and e+e- -> pi+pi-pi0pi0 dominate the inclusive hadronic cross section. The measurement of the process e+e- -> pi+pi-pi+pi- will be presented in this thesis. This channel has been previously measured by Babar based on 25% of the total dataset. The new analysis includes a more detailed study of the background contamination from other ISR and non-radiative background reactions. In addition, sophisticated studies of the track reconstruction as well as the photon efficiency difference between the data and the simulation of the Babar detector are performed. With these auxiliary studies, a reduction of the systematic uncertainty from 5.0% to 2.4% in the peak region was achieved.rnrnThe pi+pi-pi+pi- final state has a rich internal structure. Hints are seen for the intermediate states rho(770)^0 f_2(1270), rho(770)^0 f_0(980), as well as a_1(1260)pi. In addition, the branching ratios BR(jpsi -> pi+pi-pi+pi-) and BR(psitwos -> jpsi pi+pi-) are extracted.rn

Measurement of the unpolarized K+ Lambda and K+ Sigma 0 electroproduction cross-section off the proton with KAOS-spectrometer

The new stage of the Mainz Microtron, MAMI, at the Institute for Nuclear Physics of the Johannes Gutenberg-University, operational since 2007, allows open strangeness experiments to be performed. Covering the lack of electroproduction data at very low Q2, p(e,K+)Lambda and p(e,K+)Sigma0, reactions have been studied at Q^2 = 0.036(GeV/c)^2 andrnQ^2 = 0.05(GeV=c)^2 in a large angular range. Cross-section at W=1.75rnGeV will be given in angular bins and compared with the predictions of Saclay-Lyon and Kaon Maid isobaric models. We conclude that the original Kaon-Maid model, which has large longitudinal couplings of the photon to nucleon resonances, is unphysical. Extensive studies for the suitability of silicon photomultipliers as read out devices for a scintillating fiber tracking detector, with potential applications in both positive and negative arms of the spectrometer, will be presented as well.

Probing quantum chromodynamics with the ATLAS detector : charged-particle event shape variables and the dijet cross-section

Die Quantenchromodynamik ist die zugrundeliegende Theorie der starken Wechselwirkung und kann in zwei Bereiche aufgeteilt werden. Harte Streuprozesse, wie zum Beispiel die Zwei-Jet-Produktion bei hohen invarianten Massen, können störungstheoretisch behandelt und berechnet werden. Bei Streuprozessen mit niedrigen Impulsüberträgen hingegen ist die Störungstheorie nicht mehr anwendbar und phänemenologische Modelle werden für Vorhersagen benutzt. Das ATLAS Experiment am Large Hadron Collider am CERN ermöglicht es, QCD Prozesse bei hohen sowie niedrigen Impulsüberträgen zu untersuchen. In dieser Arbeit werden zwei Analysen vorgestellt, die jeweils ihren Schwerpunkt auf einen der beiden Regime der QCD legen:rnDie Messung von Ereignisformvariablen bei inelastischen Proton--Proton Ereignissen bei einer Schwerpunktsenergie von $sqrt{s} = unit{7}{TeV}$ misst den transversalen Energiefluss in hadronischen Ereignissen. rnDie Messung des zweifachdifferentiellen Zwei-Jet-Wirkungsquerschnittes als Funktion der invarianten Masse sowie der Rapiditätsdifferenz der beiden Jets mit den höchsten Transversalimpulsen kann genutzt werden um Theorievorhersagen zu überprüfen. Proton--Proton Kollisionen bei $sqrt{s} = unit{8}{TeV}$, welche während der Datennahme im Jahr 2012 aufgezeichnet wurden, entsprechend einer integrierten Luminosität von $unit{20.3}{fb^{-1}}$, wurden analysiert.rn

High-mass Drell-Yan cross-section and search for new phenomena in multi-electron/positron final states with the ATLAS detector

The Standard Model of particle physics is a very successful theory which describes nearly all known processes of particle physics very precisely. Nevertheless, there are several observations which cannot be explained within the existing theory. In this thesis, two analyses with high energy electrons and positrons using data of the ATLAS detector are presented. One, probing the Standard Model of particle physics and another searching for phenomena beyond the Standard Model.rnThe production of an electron-positron pair via the Drell-Yan process leads to a very clean signature in the detector with low background contributions. This allows for a very precise measurement of the cross-section and can be used as a precision test of perturbative quantum chromodynamics (pQCD) where this process has been calculated at next-to-next-to-leading order (NNLO). The invariant mass spectrum mee is sensitive to parton distribution functions (PFDs), in particular to the poorly known distribution of antiquarks at large momentum fraction (Bjoerken x). The measurementrnof the high-mass Drell-Yan cross-section in proton-proton collisions at a center-of-mass energy of sqrt(s) = 7 TeV is performed on a dataset collected with the ATLAS detector, corresponding to an integrated luminosity of 4.7 fb-1. The differential cross-section of pp -> Z/gamma + X -> e+e- + X is measured as a function of the invariant mass in the range 116 GeV < mee < 1500 GeV. The background is estimated using a data driven method and Monte Carlo simulations. The final cross-section is corrected for detector effects and different levels of final state radiation corrections. A comparison isrnmade to various event generators and to predictions of pQCD calculations at NNLO. A good agreement within the uncertainties between measured cross-sections and Standard Model predictions is observed.rnExamples of observed phenomena which can not be explained by the Standard Model are the amount of dark matter in the universe and neutrino oscillations. To explain these phenomena several extensions of the Standard Model are proposed, some of them leading to new processes with a high multiplicity of electrons and/or positrons in the final state. A model independent search in multi-object final states, with objects defined as electrons and positrons, is performed to search for these phenomenas. Therndataset collected at a center-of-mass energy of sqrt(s) = 8 TeV, corresponding to an integrated luminosity of 20.3 fb-1 is used. The events are separated in different categories using the object multiplicity. The data-driven background method, already used for the cross-section measurement was developed further for up to five objects to get an estimation of the number of events including fake contributions. Within the uncertainties the comparison between data and Standard Model predictions shows no significant deviations.

Measurement of the ZZ production cross section and limits to the anomalous triple gauge couplings with forward electrons with the ATLAS detector

Measurements of the self coupling between bosons are important to test the electroweak sector of the Standard Model (SM). The production of pairs of Z bosons through the s-channel is forbidden in the SM. The presence of physics, beyond the SM, could lead to a deviation of the expected production cross section of pairs of Z bosons due to the so called anomalous Triple Gauge Couplings (aTGC). Proton-proton data collisions at the Large Hadron Collider (LHC) recorded by the ATLAS detector at a center of mass energy of 8 TeV were analyzed corresponding to an integrated luminosity of 20.3 fb-1. Pairs of Z bosons decaying into two electron-positron pairs are searched for in the data sample. The effect of the inclusion of detector regions corresponding to high values of the pseudorapidity was studied to enlarge the phase space available for the measurement of the ZZ production. The number of ZZ candidates was determined and the ZZ production cross section was measured to be: rn7.3±1.0(Stat.)±0.4(Sys.)±0.2(lumi.)pb, which is consistent with the SM expectation value of 7.2±0.3pb. Limits on the aTGCs were derived using the observed yield, which are twice as stringent as previous limits obtained by ATLAS at a center of mass energy of 7 TeV.

Measurement of the e + e - pi + pi - cross section using initial state radiation at BESIII

The future goal of modern physics is the discovery of physics beyond the Standard Model. One of the most significant hints for New Physics can be seen in the anomalous magnetic moment of the muon - one of the most precise measured variables in modern physics and the main motivation of this work. This variable is associated with the coupling of the muon, an elementary particle, to an external electromagnetic field and is defined as a = (g - 2)/2, whereas g is the gyromagnetic factor of the muon. The muon anomaly has been measured with a relative accuracy of 0.5·10-6. However, a difference between the direct measurement and the Standard Model prediction of 3.6 standard deviations can be observed. This could be a hint for the existence of New Physics. Unfortunately, it is, yet, not significant enough to claim an observation and, thus, more precise measurements and calculations have to be performed.rnThe muon anomaly has three contributions, whereas the ones from quantum electrodynamics and weak interaction can be determined from perturbative calculations. This cannot be done in case of the hadronic contributions at low energies. The leading order contribution - the hadronic vacuum polarization - can be computed via a dispersion integral, which needs as input hadronic cross section measurements from electron-positron annihilations. Hence, it is essential for a precise prediction of the muon anomaly to measure these hadronic cross sections, σ(e+e-→hadrons), with high accuracy. With a contribution of more than 70%, the final state containing two charged pions is the most important one in this context.rnIn this thesis, a new measurement of the σ(e+e-→π+π-) cross section and the pion form factor is performed with an accuracy of 0.9% in the dominant ρ(770) resonance region between 600 and rn900 MeV at the BESIII experiment. The two-pion contribution to the leading-order (LO) hadronic vacuum polarization contribution to (g - 2) from the BESIII result, obtained in this work, is computed to be a(ππ,LO,600-900 MeV) = (368.2±2.5stat±3.3sys)·10-10. With the result presented in this thesis, we make an important contribution on the way to solve the (g - 2) puzzle.

Zwei-Photonen-Fluoreszenzmikroskopie und -Spektroskopie von Sauerstofftransportproteinen

In dieser Arbeit wurde die intrinsische Tryptophanfluoreszenz von Proteinen nach Zwei-Photonen-Anregung untersucht. Als interessantes Modellsystem wurde das Sauerstofftransportprotein der Vogelspinne Eurypelma californicum gewählt. Zum einen besitzt das Protein 148 Tryptophan-Seitenketten, so daß deren geringer Absorptionsquerschnitt kompensiert werden kann und eventuell einzelne Proteine aufgrund ihrer Tryptophanfluoreszenz detektiert werden können. Zum anderen signalisiert diese Fluoreszenz die Sauerstoffbeladung, so daß die kooperative Sauerstoffbindung auf Einzelmolekülebene untersucht werden könnte. Als limitierender Faktor hat sich die Photostabilität der Tryptophane nach Zwei-Photonen-Anregung herausgestellt. Im Mittel können von einem Hämocyanin-Molekül drei Photonen detektiert werden, bevor alle 148 Tryptophan-Seitenketten geblichen sind. Dies ist ein für Einzelmolekülspektroskopie äußerst niedriger Wert. Trotz dieser geringen Photostabilität ist es zum erstem Mal gelungen, die Diffusion einzelner Proteine mit Hilfe ihrer intrinsischen Tryptophanfluoreszenz zu beobachten. Wenn in einer geeigneten Umgebung die Photostabilität der Tryptophane höher ist, so reicht die Zahl der detektierten Photonen aus, um einzelne Teilchen abzubilden. Überraschend hat sich ergeben, daß es möglich ist, durch Lichteinstrahlung von außen in das Sauerstoffbindungsgleichgewicht einzugreifen und die Reaktion des Proteins auf die Auslenkung aus dem Gleichgewichtszustand zu beobachten. Das intensitätsabhängige Sauerstoffbindungsverhalten wurde modelliert und an die Messungen angepaßt. Die lichtinduzierte Sauerstoffabgabe führt anscheinend nicht zu einem Konformationswechsel.

Multichromophore Systeme auf Basis von Rylencarbonsäureimiden

Die Leistung multichromophorer Systeme geht oftmals über die der einzelnen Chromophor-Einheiten hinaus. Ziel der vorliegenden Dissertation mit dem Titel „Multichromophore Systeme auf Basis von Rylencarbonsäureimiden“ war daher die Synthese und Charakterisierung multichromophorer Molekülarchitekturen. Die verwendeten Rylenfarbstoffe zeichnen sich durch hohe photochemische Stabilitäten sowie nahezu quantitative Fluoreszenzquantenausbeuten aus. Die optischen und elektronischen Eigenschaften multichromophorer Systeme hängen stark von der geometrischen Ordnung ab, in der die Farbstoffe zueinander stehen. Daher wurden für den Einbau formpersistente Gerüststrukturen gewählt. Der erste Teil der Arbeit beschäftigt sich mit dem Einbau ein und desselben Chromophortyps und hat neben dem Verständnis von Chromophor-Wechselwirkungen vor allem die Erhöhung des Absorptionsquerschnitts und der Fluoreszenzintensität zum Ziel. Als Gerüststruktur dienen dabei Polyphenylen-Dendrimere, Ethinyl-verbrückte Dendrimere sowie Übergangsmetall-vermittelte supramolekulare Strukturen. Aufgrund der hohen Farbstoffanzahl, des ortsdefinierten Einbaus und den hohen Fluoreszenzquantenausbeuten eignen sich diese multichromophoren Systeme als Fluoreszenzsonden und als Einzelphotonenemitter. Im zweiten Teil der Arbeit werden verschiedene Chromophortypen zu multichromophoren Systemen verknüpft, mit deren Hilfe ein vektorieller Energietransfer möglich ist. Mit Hinsicht auf die Verwendung in photovoltaischen Zellen wurde eine dendritische Triade dargestellt. Eine lineare Variante einer Rylen-Triade stellt einen molekularen Draht dar, deren Brückenelement durch eine geeignete Syntheseführung verlängert und der Energietransport daher abstandsabhängig untersucht werden kann.

Laboratory study on the optical properties of absorbing atmospheric aerosols and field applications

The interaction between aerosols and sun light plays an important role in the radiative balance of Earth’s atmosphere. This interaction is obtained by measuring the removal (extinction), redistribution (scattering), and transformation into heat (absorption) of light by the aerosols; i.e. their optical properties. Knowledge of these properties is crucial for our understanding of the atmospheric system. rn Light absorption by aerosols is a major contributor to the direct and indirect effects on our climate system, and an accurate and sensitive measurement method is crucial to further our understanding. A homebuilt photoacoustic sensor (PAS), measuring at a 532nm wavelength, was fully characterized and its functionality validated for measurements of absorbing aerosols. The optical absorption cross-sections of absorbing polystyrene latex spheres, to be used as a standard for aerosol absorption measurements, were measured and compared to literature values. Additionally, a calibration method using absorbing aerosol of known complex refractive index was presented.rn A new approach to retrieve the effective broadband refractive indices (mbroad,eff) of aerosol particles by a white light aerosol spectrometer (WELAS) optical particle counter (OPC) was achieved. Using a tandem differential mobility analyzer (DMA)-OPC system, the nbroad,eff are obtained for both laboratory and field applications. This method was tested in the laboratory using substances with a wide range of optical properties and it was used in ambient measurements to retrieve the nbroad,eff of biomass burning aerosols in a nationwide burning event in Israel. The retrieved effective broadband refractive indices for laboratory generated scattering aerosols were: ammonium sulfate (AS), glutaric acid (GA), and sodium chloride, all within 4% of literature values. For absorbing substances, nigrosine and various mixtures of nigrosine with AS and GA were measured, as well as a lightly absorbing substance, Suwannee river fulvic acid (SRFA). For the ambient measurements, the calibration curves generated from this method were to follow the optical evolution of biomass burning (BB) aerosols. A decrease in the overall aerosol absorption and scattering for aged aerosols during the day after the fires compared to the smoldering phase of the fires was found. rn The connection between light extinction of aerosols, their chemical composition and hygroscopicity for particles with different degrees of absorption was studied. The extinction cross-section (σext) at 532nm for different mobility diameters was measured at 80% and 90% relative humidity (RH), and at an RH<10%. The ratio of the humidified aerosols to the dry ones, fRHext(%RH,Dry), is presented. For purely scattering aerosols, fRHext(%RH,Dry) is inversely proportional with size; this dependence was suppressed for lightly absorbing ones. In addition, the validity of the mixing rules for water soluble absorbing aerosols is explored. The difference between the derived and calculated real parts of the complex RIs were less than 5.3% for all substances, wavelengths, and RHs. The obtained imaginary parts for the retrieved and calculated RIs were in good agreement with each other, and well within the measurement errors of retrieval from pulsed CRD spectroscopy measurements. Finally, a core-shell structure model is also used to explore the differences between the models, for substances with low growth factors, under these hydration conditions. It was found that at 80% RH and for size parameters less than 2.5, there is less than a 5 % difference between the extinction efficiencies calculated with both models. This difference is within measurement errors; hence, there is no significant difference between the models in this case. However, for greater size parameters the difference can be up to 10%. For 90% RH the differences below a size parameter of 2.5 were up to 7%.rn Finally, the fully characterized PAS together with a cavity ring down spectrometer (CRD), were used to study the optical properties of soot and secondary organic aerosol (SOA) during the SOOT-11 project in the AIDA chamber in Karlsruhe, Germany. The fresh fractal-like soot particles were allowed to coagulate for 28 hours before stepwise coating them with SOA. The single scattering albedo for fresh fractal-like soot was measured to be 0.2 (±0.03), and after allowing the soot to coagulate for 28 hours and coating it with SOA, it increased to 0.71(±0.01). An absorption enhancement of the coated soot of up to 1.71 (±0.03) times from the non-coated coagulated soot was directly measured with the PAS. Monodisperse measurements of SOA and soot coated with SOA were performed to derive the complex refractive index (m) of both aerosols. A complex refractive index of m = 1.471(±0.008) + i0.0(±0.002) for the SOA-αO3 was retrieved. For the compact coagulated soot a preliminary complex refractive index of m = 2.04(+0.21/-0.14) + i0.34(+0.18/-0.06) with 10nm(+4/-6) coating thickness was retrieved.rn These detail properties can be use by modelers to decrease uncertainties in assessing climatic impacts of the different species and to improve weather forecasting.rn

Messungen von salpetriger Säure und Eispartikeln im Nachlauf von Flugzeugen

Ziel dieser Arbeit war der Aufbau und Einsatz des Atmosphärischen chemischen Ionisations-Massenspektrometers AIMS für boden- und flugzeuggetragene Messungen von salpetriger Säure (HONO). Für das Massenspektrometer wurden eine mit Gleichspannung betriebene Gasentladungsionenquelle und ein spezielles Druckregelventil entwickelt. Während der Instrumentenvergleichskampagne FIONA (Formal Intercomparisons of Observations of Nitrous Acid) an einer Atmosphären-Simulationskammer in Valencia (Spanien) wurde AIMS für HONO kalibriert und erstmals eingesetzt. In verschiedenen Experimenten wurden HONO-Mischungsverhältnisse zwischen 100 pmol/mol und 25 nmol/mol erzeugt und mit AIMS interferenzfrei gemessen. Innerhalb der Messunsicherheit von ±20% stimmen die massenspektrometrischen Messungen gut mit den Methoden der Differenziellen Optischen Absorptions-Spektrometrie und der Long Path Absorption Photometrie überein. Die Massenspektrometrie kann somit zum schnellen und sensitiven Nachweis von HONO in verschmutzter Stadtluft und in Abgasfahnen genutzt werden.rnErste flugzeuggetragene Messungen von HONO mit AIMS wurden 2011 bei der Messkampagne CONCERT (Contrail and Cirrus Experiment) auf dem DLR Forschungsflugzeug Falcon durchgeführt. Hierbei konnte eine Nachweisgrenze von < 10 pmol/mol (3σ, 1s) erreicht werden. Bei Verfolgungsflügen wurden im jungen Abgasstrahl von Passagierflugzeugen molare HONO zu Stickoxid-Verhältnisse (HONO/NO) von 2.0 bis 2.5% gemessen. HONO wird im Triebwerk durch die Reaktion von NO mit OH gebildet. Ein gemessener abnehmender Trend der HONO/NO Verhältnisse mit zunehmendem Stickoxid-Emissionsindex wurde bestätigt und weist auf eine OH Limitierung im jungen Abgasstrahl hin.rnNeben den massenspektrometrischen Messungen wurden Flugzeugmessungen der Partikelsonde Forward Scattering Spectrometer Probe FSSP-300 in jungen Kondensstreifen ausgewertet und analysiert. Aus den gemessenen Partikelgrößenverteilungen wurden Extinktions- und optische Tiefe-Verteilungen abgeleitet und für die Untersuchung verschiedener wissenschaftlicher Fragestellungen, z.B. bezüglich der Partikelform in jungen Kondensstreifen und ihrer Klimawirkung, zur Verfügung gestellt. Im Rahmen dieser Arbeit wurde der Einfluss des Flugzeug- und Triebwerktyps auf mikrophysikalische und optische Eigenschaften von Kondensstreifen untersucht. Unter ähnlichen meteorologischen Bedingungen bezüglich Feuchte, Temperatur und stabiler thermischer Schichtung wurden 2 Minuten alte Kondensstreifen der Passagierflugzeuge vom Typ A319-111, A340-311 und A380-841 verglichen. Im Rahmen der Messunsicherheit wurde keine Änderung des Effektivdurchmessers der Partikelgrößenverteilungen gefunden. Hingegen nehmen mit zunehmendem Flugzeuggewicht die Partikelanzahldichte (162 bis 235 cm-3), die Extinktion (2.1 bis 3.2 km-1), die Absinktiefe des Kondensstreifens (120 bis 290 m) und somit die optische Tiefe der Kondensstreifen (0.25 bis 0.94) zu. Der gemessene Trend wurde durch Vergleich mit zwei unabhängigen Kondensstreifen-Modellen bestätigt. Mit den Messungen wurde eine lineare Abhängigkeit der totalen Extinktion (Extinktion mal Querschnittsfläche des Kondensstreifens) vom Treibstoffverbrauch pro Flugstrecke gefunden und bestätigt.