Noble-metal nanoparticles produced with colloidal lithography: fabrication, optical properties and applications

In this work, metal nanoparticles produced by nanosphere lithography were studied in terms of their optical properties (in connection to their plasmon resonances), their potential application in sensing platforms - for thin layer sensing and bio-recognition events -, and for a particular case (the nanocrescents), for enhanced spectroscopy studies. The general preparation procedures introduced early in 2005 by Shumaker-Parry et al. to produce metallic nanocrescents were extended to give rise to more complex (isolated) structures, and also, by combining colloidal monolayer fabrication and plasma etching techniques, to arrays of them. The fabrication methods presented in this work were extended not only to new shapes or arrangements of particles, but included also a targeted surface tailoring of the substrates and the structures, using different thiol and silane compounds as linkers for further attachment of, i.e. polyelectrolyte layers, which allow for a controlled tailoring of their nanoenvironment. The optical properties of the nanocrescents were studied with conventional transmission spectroscopy; a simple multipole model was adapted to explain their behaviour qualitatively. In terms of applications, the results on thin film sensing using these particles show that the crescents present an interesting mode-dependent sensitivity and spatial extension. Parallel to this, the penetrations depths were modeled with two simplified schemes, obtaining good agreement with theory. The multiple modes of the particles with their characteristic decay lengths and sensitivities represent a major improvement for particle-sensing platforms compared to previous single resonance systems. The nanocrescents were also used to alter the emission properties of fluorophores placed close to them. In this work, green emitting dyes were placed at controlled distances from the structures and excited using a pulsed laser emitting in the near infrared. The fluorescence signal obtained in this manner should be connected to a two-photon processes triggered by these structures; obtaining first insight into plasmon-mediated enhancement phenomena. An even simpler and faster approach to produce plasmonic structures than that for the crescents was tested. Metallic nanodiscs and nanoellipses were produced by means of nanosphere lithography, extending a procedure reported in the literature to new shapes and optical properties. The optical properties of these particles were characterized by extinction spectroscopy and compared to results from the literature. Their major advantage is that they present a polarization-dependent response, like the nanocrescents, but are much simpler to fabricate, and the resonances can be tailored in the visible with relative ease. The sensing capabilities of the metallic nanodiscs were explored in the same manner as for the nanocrescents, meaning their response to thin layers and to bio-recognition events on their surface. The sensitivity of these nanostructures to thin films proved to be lower than that of the crescents, though in the same order of magnitude. Experimental information about the near field extension for the Au nanodiscs of different sizes was also extracted from these measurements. Further resonance-tailoring approaches based on electrochemical deposition of metals on the nanodiscs were explored, as a means of modifying plasmon resonances by changing surface properties of the nanoparticles. First results on these experiments would indicate that the deposition of Ag on Au on a submonolayer coverage level can lead to important blue-shifts in the resonances, which would open a simple way to tailor resonances by changing material properties in a local manner.

An alternative blocking layer for titanium dioxide (TiO 2) solar cell applications

In hybrid organic solar cells a blocking layer between transparent electrode and nanocrystalline titania particles is essential to prevent short-circuiting and current loss through recombination at the electrode interface. Here the preparation of a uniform hybrid blocking layer which is composed of conducting titania nanoparticles embedded in an insulating polymer derived ceramic is presented. This blocking layer is prepared by sol-gel chemistry where an amphiphilic block copolymer is used as a templating agent. A novel poly(dimethylsiloxane) containing amphiphilic block copolymer poly(ethyleneglycol)methylethermethacrylate-block-poly(dimethylsiloxane)-block-poly(ethyleneglycol)methylethermethacrylate has been synthesized to act as the templating agent. Plasma treatment uncovered titania surface from any polymer. Annealing at 450°C under nitrogen resulted in anatase titania with polymer derived silicon oxycarbide ceramic. Electrical characterization by conductive scanning probe microscopy experiments revealed a percolating titania network separated by an insulating ceramic matrix. Scanning Kelvin probe force microscopy showed predominant presence of titania particles on the surface creating a large surface area for dye absorption. The uniformity of the percolating structures was proven by microbeam grazing incidence small angle x-ray scattering. First applications in hybrid organic solar cells in comparison with conventional titanium dioxide blocking layer containing devices revealed 15 fold increases in corresponding efficiencies. Poly(dimethylsiloxane)-block-poly(ethyleneglycol)methylethermethacrylate and poly(ethyleneoxide)-poly(dimethylsiloxane)methylmethacrylate diblock copolymers were also synthesized. Their titania nanocomposite films were compared with the integrated blocking layer. Liner poly(ethyleneoxide) containing diblock copolymer resulted in highly ordered foam like structures. The effect of heating temperature rise to 600°C and 1000°C on titania morphology was investigated by scanning electron and force microscopy and x-ray scattering. Sol-gel contents, hydrochloric acid, titania precursor and amphiphilic triblock copolymer were altered to see their effect on titania morphology. Increase in block copolymer content resulted in titania particles of diameter 15-20 nm.

Variation of stable silicon isotopes: Analytical developments and applications in Precambrian geochemistry

Die vorliegende Dissertation behandelt die Gesamtgesteinsanalyse stabiler Siliziumisotope mit Hilfe einer „Multi Collector-ICP-MS“. Die Analysen fanden in Kooperation mit dem „Royal Museum for Central Africa“ in Belgien statt. Einer der Schwerpunkte des ersten Kapitels ist die erstmalige Analyse des δ30Si –Wertes an einem konventionellen Nu PlasmaTM „Multi-Collector ICP-MS“ Instrument, durch die Eliminierung der den 30Si “peak” überlagernden 14N16O Interferenz. Die Analyse von δ30Si wurde durch technische Modifikationen der Anlage erreicht, welche eine höherer Massenauflösung ermöglichten. Die sorgsame Charakterisierung eines adäquaten Referenzmaterials ist unabdingbar für die Abschätzung der Genauigkeit einer Messung. Die Bestimmung der „U.S. Geological Survey“ Referenzmaterialien bildet den zweiten Schwerpunkt dieses Kapitales. Die Analyse zweier hawaiianischer Standards (BHVO-1 and BHVO-2), belegt die präzise und genaue δ30Si Bestimmung und bietet Vergleichsdaten als Qualitätskontrolle für andere Labore. Das zweite Kapitel befasst sich mit kombinierter Silizium-/Sauerstoffisotope zur Untersuchung der Entstehung der Silizifizierung vulkanischer Gesteine des „Barberton Greenstone Belt“, Südafrika. Im Gegensatz zu heute, war die Silizifizierung der Oberflächennahen Schichten, einschließlich der „Chert“ Bildung, weitverbreitete Prozesse am präkambrischen Ozeanboden. Diese Horizonte sind Zeugen einer extremen Siliziummobilisierung in der Frühzeit der Erde. Dieses Kapitel behandelt die Analyse von Silizium- und Sauerstoffisotopen an drei unterschiedlichen Gesteinsprofilen mit unterschiedlich stark silizifizierten Basalten und überlagernden geschichteten „Cherts“ der 3.54, 3.45 und 3.33 Mill. Jr. alten Theespruit, Kromberg und Hooggenoeg Formationen. Siliziumisotope, Sauerstoffisotope und die SiO2-Gehalte demonstrieren in allen drei Gesteinsprofilen eine positive Korrelation mit dem Silizifizierungsgrad, jedoch mit unterschiedlichen Steigungen der δ30Si-δ18O-Verhältnisse. Meerwasser wird als Quelle des Siliziums für den Silizifizierungsprozess betrachtet. Berechnungen haben gezeigt, dass eine klassische Wasser-Gestein Wechselwirkung die Siliziumisotopenvariation nicht beeinflussen kann, da die Konzentration von Si im Meerwasser zu gering ist (49 ppm). Die Daten stimmen mit einer Zwei-Endglieder-Komponentenmischung überein, mit Basalt und „Chert“ als jeweilige Endglieder. Unsere gegenwärtigen Daten an den „Cherts“ bestätigen einen Anstieg der Isotopenzusammensetzung über der Zeit. Mögliche Faktoren, die für unterschiedliche Steigungen der δ30Si-δ18O Verhältnisse verantwortlich sein könnten sind Veränderungen in der Meerwasserisotopie, der Wassertemperatur oder sekundäre Alterationseffekte. Das letzte Kapitel beinhaltet potentielle Variationen in der Quellregion archaischer Granitoide: die Si-Isotopen Perspektive. Natriumhaltige Tonalit-Trondhjemit-Granodiorit (TTG) Intrusiva repräsentieren große Anteile der archaischen Kruste. Im Gegensatz dazu ist die heutige Kruste kaliumhaltiger (GMS-Gruppe: Granit-Monzonite-Syenite). Prozesse, die zu dem Wechsel von natriumhaltiger zu kaliumhaltiger Kruste führten sind die Thematik diesen Kapitels. Siliziumisotopenmessungen wurden hier kombiniert mit Haupt- und Spurenelementanalysen an unterschiedlichen Generationen der 3.55 bis 3.10 Mill. Yr. alten TTG und GMS Intrusiva aus dem Arbeitsgebiet. Die δ30Si-Werte in den unterschiedlichen Plutonit Generationen zeigen einen leichten Anstieg der Isotopie mit der Zeit, wobei natriumhaltige Intrusiva die niedrigste Si-Isotopenzusammensetzung aufweisen. Der leichte Anstieg in der Siliziumisotopenzusammensetzung über die Zeit könnte auf unterschiedliche Temperaturbedingungen in der Quellregion der Granitoide hinweisen. Die Entstehung von Na-reichen, leichten d30Si Granitoiden würde demnach bei höheren Temperaturen erfolgen. Die Ähnlichkeit der δ30Si-Werte in archaischen K-reichen Plutoniten und phanerozoischen K-reichen Plutoniten wird ebenfalls deutlich.

Thiophene-containing organic semiconducting heteroacenes for electronic applications

Diese Studie verfolgt das Konzept der "Oligomer-Ansatz", die von Müllen angesprochen wurde et.al. vor etwa 10 Jahren. Der Schwerpunkt dieser Arbeit war die Synthese, Charakterisierung und Anwendung von halbleitenden konjugierten heteroacenes für organische Elektronik.rnZur weiteren Entwicklung der Familie von schwefelhaltigen Pentacene, zwei Moleküle (Benzo [1,2 - b :4,5-b '] bis [b] benzodithiophene und dithieno-[2,3-d: 2', 3'-d ']-benzo-[1,2-b :4,5-b'] dithiophene)rnfacilely wurden synthetisiert und charakterisiert durch eine Kombination verschiedener Methoden. Die beiden neue Moleküle weisen hervorragende ökologische Stabilität und angewendet OFETs Geräte als p-Kanal-Material. Die Vorversuche gaben Ladungsträgerbeweglichkeiten von 0,1 cm2 V-1 s-1 undrn1,6 cm2 V-1 s-1 bzw. aus den beiden Molekülen.rnAusgelöst durch die Frage "je länger desto besser?", Eine Reihe von neuen heteroheptacenes wurden synthetisiert und intensiv im Hinblick auf ihre feste Struktur, Selbst-assenbly auf der studierte Oberfläche, opto-elektro-Eigenschaften und Eigenschaften des Orbits Grenze. Einer derrnheteroheptacene Moleküle wurden als die aktiven Kanäle in OFET Geräten angewendet. Jedoch in Trotz der mehr verlängert Konjugationslänge die Geräte auf der Basis zeigten heptacenes viel schlimmer Ladungsträgerbeweglichkeiten als die heteropentacenes. Viele Faktoren können Festlegung der endgültigen Leistung der Produkte und der chemischen Struktur ist nur einer von ihnen.rnIn dieser Hinsicht scheint es, dass es auch sinnvoll, den Einfluss der Heteroatome Studie und Alkylsubstitution auf der soliden und elektronischen Strukturen. Daher mehr heteroheptacenes wurden synthetisiert. Abwechslungsreiches in der Anzahl und Art der heteroatomare Brücke,rndiese Oligoazene ausgestellt dramatisch anders feste Struktur und opto-elektronischernEigenschaften. Darüber hinaus wurde eine kombinierte DFT Berechnung der Molekülorbitale dieser heptacenes darauf hingewiesen, dass die Einführung von Stickstoff Brücken wird die π-Orbitale zu destabilisieren, während stabilisieren den Schwefel Brücken sowohl HOMO und LUMO Energien. Dies ist wichtig, wenn man will hoch π verlängert Oligoazene synthetisieren und dabei eine angemessene Stabilität.

Quantum dot-dye hybrid systems for energy transfer applications

In this thesis, we focus on the preparation of energy transfer-based quantum dot (QD)-dye hybrid systems. Two kinds of QD-dye hybrid systems have been successfully synthesized: QD-silica-dye and QD-dye hybrid systems.rn rnIn the QD-silica-dye hybrid system, multishell CdSe/CdS/ZnS QDs were adsorbed onto monodisperse Stöber silica particles with an outer silica shell of thickness 2 - 24 nm containing organic dye molecules (Texas Red). The thickness of this dye layer has a strong effect on the total sensitized acceptor emission, which is explained by the increase in the number of dye molecules homogeneously distributed within the silica shell, in combination with an enhanced surface adsorption of QDs with increasing dye amount. Our conclusions were underlined by comparison of the experimental results with Monte-Carlo simulations, and by control experiments confirming attractive interactions between QDs and Texas Red freely dissolved in solution. rnrnNew QD-dye hybrid system consisting of multishell QDs and organic perylene dyes have been synthesized. We developed a versatile approach to assemble extraordinarily stable QD-dye hybrids, which uses dicarboxylate anchors to bind rylene dyes to QD. This system yields a good basis to study the energy transfer between QD and dye because of its simple and compact design: there is no third kind of molecule linking QD and dye; no spacer; and the affinity of the functional group to the QD surface is strong. The FRET signal was measured for these complexes as a function of both dye to QD ratio and center-to-center distance between QD and dye by controlling number of covered ZnS layers. Data showed that fluorescence resonance energy transfer (FRET) was the dominant mechanism of the energy transfer in our QD-dye hybrid system. FRET efficiency can be controlled by not only adjusting the number of dyes on the QD surface or the QD to dye distance, but also properly choosing different dye and QD components. Due to the strong stability, our QD-dye complexes can also be easily transferred into water. Our approach can apply to not only dye molecules but also other organic molecules. As an example, the QDs have been complexed with calixarene molecules and the QD-calixarene complexes also have potential for QD-based energy transfer study. rn

DNA hybrid materials consisting of oligonucleotides and organic molecules: synthesis, characterization and applications

The goal of this thesis was to increase the functionality of pristine DNA scaffolds by functionalizing them with fluorescent dyes and hydrophobic moieties. Two important steps were necessary to realize this aim successfully. First, nucleic acids needed to be synthesized making use of multidisciplinary toolbox for the generation and manipulation of polynucleic acids. The most important techniques were the solid phase synthesis involving the incorporation of standard and modified phosphoramidite building blocks as well as molecular biology procedures like the polymerase chain reaction, the bacterial amplification of plasmids and the enzymatic digestion of circular vectors. Second, and evenly important, was the characterization of the novel bioorganic hybrid structures by a multitude of techniques, especially optical measurements. For studying DNA-dye conjugates methods like UV/Vis and photoluminescence spectroscopy as well as time resolved luminescence spectroscopy were utilized. While these measurements characterized the bulk behavior of an ensemble of DNA-dye hybrids it was necessary for a complete understanding of the systems to look at single structures. This was done by single-molecule fluorescence spectroscopy and fluorescence correlation spectroscopy. For complete analysis the optical experiments were complemented by direct visualization techniques, i.e. high resolution transmission electron microscopy and scanning force microscopy.

New biosensor applications of surface plasmon and hydrogel optical waveguide spectroscopy

Rapid and sensitive detection of chemical and biological analytes becomes increasingly important in areas such as medical diagnostics, food control and environmental monitoring. Optical biosensors based on surface plasmon resonance (SPR) and optical waveguide spectroscopy have been extensively pushed forward in these fields. In this study, we combine SPR, surface plasmon-enhanced fluorescence spectroscopy (SPFS) and optical waveguide spectroscopy with hydrogel thin film for highly sensitive detection of molecular analytes.rnrnA novel biosensor based on SPFS which was advanced through the excitation of long range surface plasmons (LRSPs) is reported in this study. LRSPs are special surface plasmon waves propagating along thin metal films with orders of magnitude higher electromagnetic field intensity and lower damping than conventional SPs. Therefore, their excitation on the sensor surface provides further increased fluorescence signal. An inhibition immunoassay based on LRSP-enhanced fluorescence spectroscopy (LRSP-FS) was developed for the detection of aflatoxin M1 (AFM1) in milk. The biosensor allowed for the detection of AFM1 in milk at concentrations as low as 0.6 pg mL-1, which is about two orders of magnitude lower than the maximum AFM1 residue level in milk stipulated by the European Commission legislation.rnrnIn addition, LRSPs probe the medium adjacent to the metallic surface with more extended evanescent field than regular SPs. Therefore, three-dimensional binding matrices with up to micrometer thickness have been proposed for the immobilization of biomolecular recognition elements with large surface density that allows to exploit the whole evanescent field of LRSP. A photocrosslinkable carboxymethyl dextran (PCDM) hydrogel thin film is used as a binding matrix, and it is applied for the detection of free prostate specific antigen (f-PSA) based on the LRSP-FS and sandwich immunoassay. We show that this approach allows for the detection of f-PSA at low femto-molar range, which is approximately four orders of magnitude lower than that for direct detection of f-PSA based on the monitoring of binding-induced refractive index changes.rnrnHowever, a three dimensional hydrogel binding matrix with micrometer thickness can also serve as an optical waveguide. Based on the measurement of binding-induced refractive index changes, a hydrogel optical waveguide spectroscopy (HOWS) is reported for a label-free biosensor. This biosensor is implemented by using a SPR optical setup in which a carboxylated poly(N-isoproprylacrylamide) (PNIPAAm) hydrogel film is attached on a metallic surface and modified by protein catcher molecules. Compared to regular SPR biosensor with thiol self-assembled monolayer (SAM), HOWS provides an order of magnitude improved resolution in the refractive index measurements and enlarged binding capacity owing to its low damping and large swelling ratio, respectively. A model immunoassay experiment revealed that HOWS allowed detection of IgG molecules with a 10 pM limit of detection (LOD) that was five-fold lower than that achieved for SPR with thiol SAM. For the high capacity hydrogel matrix, the affinity binding was mass transport limited.rnrnThe mass transport of target molecules to the sensor surface can play as critical a role as the chemical reaction itself. In order to overcome the diffusion-limited mass transfer, magnetic iron oxide nanoparticles were employed. The magnetic nanoparticles (MNPs) can serve both as labels providing enhancement of the refractive index changes, and “vehicles” for rapidly delivering the analytes from sample solution to an SPR sensor surface with a gradient magnetic field. A model sandwich assay for the detection of β human chorionic gonadotropin (βhCG) has been utilized on a gold sensor surface with metallic diffraction grating structure supporting the excitation of SPs. Various detection formats including a) direct detection, b) sandwich assay, c) MNPs immunoassay without and d) with applied magnetic field were compared. The results show that the highly-sensitive MNPs immunoassay improves the LOD on the detection of βhCG by a factor of 5 orders of magnitude with respect to the direct detection.rn

From amphiphilic block copolymers to ferrocenyl-functionalized polymers for biosensoric applications

The present thesis can be divided in three main parts. In all parts new polymer architecturesrnwere synthesized and characterized concerning their special features.rnThe first part will emphasize the advantage of a polystyrene-block-(hyperbranchedrnpolyglycerol) copolymer in comparison to an analogue polystyrene-block-(linear polyglycerol)rncopolymer. Therefore a synthethic route to prepare linear block copolymersrnhas been developed. Two strategies were examined. One strategy was based on thernclassic, sequential anionic polymerization; the second strategy was based on arn“Click-Chemistry” coupling reaction. In a following step glycidol was hypergraftedrnfrom these block copolymers by applying a hypergrafting reaction with glycidol. Thernbehavior of the amphiphilic block copolymers synthesized was studied in differentrnsolvents. Furthermore the polarity of the solvent was changed to form the correspondingrninverse micelles. DLS, SLS, SEC-MALLS-VISCO, AFM and Cyro TEMrnmeasurements were performed to obtain a visual image from the appearance of thernaggregates. It was found that a linear-hyperbranched architecture is necessary, ifrnwell defined, monodisperse aggregates are required, e.g. for the preparation of orderedrnnanoarrays. Linear-linear block copolymers formed only polydisperse aggregates.rnAdditionally it was found that size distribution could be improved dramaticallyrnby passing the aggregates through a SEC column with large pores. The SEC columnsrnacted like a template in which the aggregates adopt a more stable conformation.rnIn the second part anionic polymerization was employed to synthesize silaneendfunctionalizedrnmacromonomers with different molecular weights based on polybutadienernand polyisoprene. These were polymerized by a hydrosilylation reaction inrnbulk to obtain branched polymers, using Karstedt’s catalyst. Surprisingly the additionrnof monofunctional silanes during the polymerization had only a minimal effect concerningrnthe degree of polymerization. It was possible to introduce silanes without increasingrnthe overall number of reaction steps by a very convenient “pseudo-copolymerization”rnmethod. All branched polymers were analyzed by SEC, SEC-MALLS,rnSEC-viscometry, 1H-NMR-spectroscopy and DSC concerning their branching ratio.rnThe branching parameters for the branched polymers exhibited similar characteristicsrnas hyperbranched polymers based on AB2 monomers. Detailed kinetic study showedrnthat the polymerization occurred very rapidly in comparison to the hydrosilylation polymerizationrnof classical AB2 type carbosilanes monomers.rnThe last part will deal with ferrocenyl-functionalized polymers. On the one hand,rnferrocenyl-functionalized polyglycerols (PG) were studied. Esterification of PGs withrndifferent molecular weight using ferrocenemonocarboxylic acid gave the ferrocenylrnfuntionalized polymers in high yields. On the other hand three different block copolymersrnwere prepared with different ratios of styrene to butadiene units (10:1, 4:1, 2:1).rnThe double bonds of the 1,2-PB block were hydrosilylated using silanes bearing onern(HSiMe2Fc) or two (HSiMeFc2) ferrocene units. High degrees of functionalizationrnwere obtained (up to 83 %). In this manner, six different ferrocenyl-rich block copolymersrnwith different fractions of ferrocene were prepared and analyzed, employingrnNMR-spectroscopy, SEC, SEC/MALLS/viscometry, DLS and cyclic voltammetry. Thernredox properties of the studied polymers varied primarily with the nature of the silanernunit attached. Additionally, the redox properties in solution of the studied polymersrnwere influenced by the block length ratio of the block copolymers. Unexpectedly, withrnincreasing block length of the ferrocenyl block the fraction of active ferrocenes decreased.rnNevertheless, in case of thin monolayer films this behaviour was not observed.rnAll polymers (PG and PS-b-PB based) exhibited good electrochemical propertiesrnin a wide range of solvents, which rendered them very interesting for biosensoricrnapplications.

Multifunctional magnetically loaded polyorganosiloxane nanocomposites for biomedical applications

For the last few decades, the interest in functional nanomaterials is steadily increasing. Especially, in biomedicine the range of possible applications of multifunctional nanoparticles including dye-labeled makers and drug loaded carrier systems is extraordinary large. The incorporation of magnetic nanoparticles allows for an additional magnetic detection and manipulation. One promising system on the way to multifunctional nanomaterials is the polyorganosiloxane system. Via polycondensation of silan monomers in aqueous dispersion polyorganosiloxane nanoparticles with particle diameter between 10 and 150 nm can be synthesized. The versatile silane chemistry allows for the design of multifunctional network structures. In this work, hydrophilic iron oxide nanoparticles could be encapsulated into the polymeric particles in a highly efficient process whereat the superparamagnetic nature of the inorganic particles was restrained. The influence of different sized particles as well as the amount of the incorporated material was investigated. Using a core-shell architecture, controlled core and surface modifications could be achieved. An effective fluorescent labeling was performed via incorporation of dye-labeled monomers. Additionally, a hydrophilic surface modification was carried out via a grafting onto process of poly(ethylene glycol). Individual core and surface functionalization was achieved and the influence of the modification on the efficiency of the magnetic loading was tested. The applicability of the multifunctional particles in biological systems was proved via cellular uptake and toxicity testings. Furthermore, biofunctionalized particles were synthesized by EDC coupling using biotin and insulin.rnrn

Polymer-nanoparticle composites: from orientation phenomena to optoelectronic applications

Polymer-nanoparticle hybrids show synergistic effects, demonstrating both, the unique properties of nanosized structures and the good processability and functionalities of polymeric materials. This work shows the synthesis and application of block copolymers containing a soluble, functional block and a short anchor block, which efficiently binds to the surface of nanocrystals. We functionalized anisotropic, semiconducting nanoparticles, which can be dissolved in organic and polymeric matrices upon modification. The modified nanorods have the ability to form liquid crystalline phases, which behave similar to low molecular liquid crystals with a reversible clearing behaviour. These liquid crystalline phases could also be obtained in hole conducting matrices. For a macroscopic orientation of the nanorods, electric fields were applied and a switching (in analogy to known liquid crystals) to a homeotropic orientation was observed.rnBy introduction of dye molecules in the anchor block of a hole conducting block copolymer, all essential components of a solar cell can be combined in a single particle. Light absorption of the dye induces the injection of electrons into the particles, followed by a charging, that was monitored by a special AFM technique.rnLight emitting nanocrystals were functionalized analogously with a hole transporting polymer. The stability of the particles could be enhanced by the sterically stabilizing polymer corona and the particles showed improved properties in terms of processing. We applied these hybrid materials in light emitting devices, which showed better characteristics due to an improved hole injection and well dispersed emitting particles in the active device layer.rnThe work shows the broad spectrum of properties and applications based on the synergistic effects in hybrid and composite materials.

Role of outgrowth endothelial cells for applications in tissue engineering

Co-culture systems, consisting of outgrowth endothelial cells (OEC) and primary osteoblasts (pOB), represent a prom¬ising instrument to mimick the natural conditions in bone repair processes and provide a new concept to develop constructs for bone replacement. Furthermore, co-culture of OEC and pOB could provide new insights into the molecular and cellular mechanisms that control essential processes during bone repair. The present study described several advantages of the co-culture of pOB and OEC for bone tissue engineering applications, including beneficial effects on the angiogenic activation of OEC, as well as on the assembly of basement membrane matrix molecules and factors involved in vessel maturation and stabilization. The ongoing angiogenic process in the co-culture system proceeded during the course of co-cultivation and correlated with the upregulation of essential angiogenic factors, such as VEGF, angiopoietins, basement membrane molecules and mural cell-specific markers. Furthermore the co-culture system appeared to maintain osteogenic differentiation capacity.rnrnAdditional treatment of co-cultures with growth factors or morphogens might accelerate and improve bone formation and furthermore could be useful for potential clinical applications. In this context, the present study highlights the central role of the morphogen, sonic hedgehog, which has been shown to affect angiogenic activation as well as osteogenic differentiation in the co-culture model of OEC and pOB. Treatment of co-cultures with sonic hedgehog resulted in an increased formation of microvessel-like structures as early as after 24 hours. This proangiogenic effect was induced by the upregulation of the proangiogenic factors, VEGF, angiopoietin1 and angiopoietin 2. In contrast to treatment with a commonly used proangiogenic agent, VEGF, Shh stimulation induced an increased expression of factors associated with vessel maturation and stabilization, mediated through the upregulation of growth factors that are strongly involved in pericyte differentiation and recruitment, including PDGF-BB and TGFbeta. In addition, Shh treatment of co-cultures also resulted in an upregulation of osteogenic differentiation markers like alkaline phosphatase, osteocalcin, osteonectin and osteopontin, as well as an increased matrix calcification. This was a result of upregulation of the osteogenic differentiation regulating factors, BMP2 and RUNX2 which could be assessed in response to Shh treatment. rn

Structure and properties of quaternary and tetragonal Heusler compounds for spintronics and spin transfer torque applications

Diese Dissertation ist in zwei Teile aufgeteilt: Teil 1 befasst sich mit der Vorhersage von Halb-Metallizität in quarternären Heuslerverbindungen und deren Potential für Spintronik-Anwendungen. Teil 2 befasst sich mit den strukturellen Eigenschaften der Mn2-basierenden Heuslerverbindungen und dem Tuning von ihrer magnetischen Eigenschaften bzgl. Koerzitivfeldstärke und Remanenz. Diese Verbindungen sind geeignet für Spin-Transfer Torque-Anwendungen.rnrnIn Teil 1 wurden die folgenden drei Probenserien quarternärer Heuslerverbindungen untersucht: XX´MnGa (X = Cu, Ni und X´ = Fe, Co), CoFeMnZ (Z = Al, Ga, Si, Ge) und Co2−xRhxMnZ (Z = Ga, Sn, Sb). Abgesehen von CuCoMnGa wurden alle diese Verbindungen mittels ab-initio Bandstrukturrechnungen als halbmetallische Ferromagnete prognostiziert. In der XX´MnGa-Verbindungsklasse besitzt NiFeMnGa zwar eine zu niedrige Curie-Temperatur für technologische Anwendungen, jedoch NiCoMnGa mit seiner hohen Spinpolarisation, einem hohen magnetischen Moment und einer hohen Curie-Temperatur stellt ein neues Material für Spintronik-Anwendungen dar. Alle CoFeMnZ-Verbindungen kristallisieren in der kubischen Heuslerstruktur und ihre magnetischen Momente folgen der Slater-Pauling-Regel, was Halbmetalizität und eine hohe Spinpolarisation impliziert. Die ebenfalls hohen Curie-Temperaturen ermöglichen einen Einsatz weit über Raumtemperatur hinaus. In der strukturellen Charakterisierung wurde festgestellt, dass sämtliche Co2−xRhxMnZ abgesehen von CoRhMnSn verschiedene Typen von Unordnung aufweisen; daher war die ermittelte Abweichung von der Slater-Pauling-Regel sowie von der 100%-igen Spinpolarisation dieser Verbindungen zu erwarten. Die Halbmetallizität der geordneten CoRhMnSn-Verbindung sollte nach den durchgeführten magnetischen Messungen vorhanden sein.rnrnIm zweiten Teil wurden Mn3−xCoxGa und Mn2−xRh1+xSn synthetisiert und charakterisiert. Es wurde gezeigt, dass Mn3−xCoxGa im Bereich x = 0.1 − 0.4 in einer tetragonal verzerrten inversen Heuslerstruktur kristallisiert und im Bereich x = 0.6−1 in einer kubisch inversen Heuslerstruktur. Während die tetragonalen Materialien hartmagnetisch sind und Charakeristika aufweisen, die typischerweise für Spin-Transfer Torque-Anwengungen attraktiv sind, repräsentieren die weichmagnetischen kubischen Vertreter die 100% spinpolarisierten Materialien, die der Slater-Pauling-Regel folgen. Mn2RhSn kristallisiert in der inversen tetragonal verzerrten Heuslerstruktur, weist einernhartmagnetische Hystereseschleife auf und folgt nicht der Slater-Pauling-Regel. Bei hohen Rh-Gehalt wird die kubische inverse Heuslerstruktur gebildet. Alle kubischen Proben sind weichmagnetisch und folgen der Slater-Pauling-Regel.

Hyperbranched polyglycerols as building blocks for complex amphiphilic structures: synthesis, characterization and applications

Among hyperbranched polymers, polyglycerol is one of the most promising and commonly used macromolecules due to its biocompatibility and versatility. However, the synthesis of high molecular weight polyglycerols still involves many intricacies and has only been understood to a limited extent. Furthermore, only few complex structures like star or block copolymers incorporating polyglycerol have been realized so far. Particularly biocompatible block copolymers are considered promising candidates for biomedical applications.rnThe scope of this thesis was the enhancement of the synthetic process leading to polyglycerol derivatives which implies improved molecular weight control for a broad molecular weight range as well as the assembly of more complex structures like amphiphilic block copolymers. Further insight into the relation between reaction solvent, degree of deprotonation during the ring-opening multibranching polymerization of glycidol and the characteristics of the obtained polymers were achieved within the scope of this work. Based on these results, a novel concept for the preparation of hyperbranched polyglycerols with molecular weights up to 20,000 g/mol was developed, applying a two step synthesis pathway. Starting from a partially deprotonated TMP core, low molecular weight hb-PGs were prepared using the known synthetic protocol that has been established since the late 1990ies. In a subsequent reaction sequence, these well defined polymers were used as hyperbranched macroinitiator cores in order to obtain high molecular weight hb-PGs with remarkably low polydispersity (Mw/Mn < 1.8). Molecular weight control was shown to be excellent and undesired low molecular weight side products were absent. Furthermore, the technique of continuous spin fractionation has been discovered as an efficient method for polyglycerol work-up to remove quantitatively residual monomer- and oligomer traces from hb-PG compositions to result in samples with significantly reduced polydispersities. Based on these results the synthesis of amphiphilic block copolymers containing hydrophilic hyperbranched polyglycerol blocks and linear, apolar poly(propylene oxide) blocks has been significantly improved and augmented to hb-PG-b-l-PPO-b-hb-PG ABA block copolymers. The influence of different polyglycerol-based amphiphiles on the fibril formation was studied by Thioflavin T Fluorescence showing remarkable increasing lag times which is promising in order to enhance the stability of this protein. In addition the first synthesis of poly(glyceryl glycerols) (PGG), introducing a new solketyl glycidyl ether monomer (IGG) was shown. It was furthermore demonstrated that core-functional carbosilane wedges allow application in block copolymer synthesis. Bisglycidolized amine functional polymers were successfully employed as macroinitiators for glycidol polymerization. This resulted in the first example of amphiphilic hyperbranched-hyperbranched polymer structures. Finally, it has been shown that the previously reported synthetic pathway to carboxylated hyperbranched polyglycerol polyelectrolytes can also be applied for the amphiphilic linear-hyperbranched block copolymers. These novel biocompatible and highly amphiphilic polyelectrolytes offer great potential for further investigations. rnrn

Electronic structure and physical properties of Heusler compounds for thermoelectric and spintronic applications

This thesis focuses on synthesis as well as investigations of the electronic structure and properties of Heusler compounds for spintronic and thermoelectric applications.rnThe first part reports on the electronic and crystal structure as well as the mechanical, magnetic, and transport properties of the polycrystalline Heusler compound Co2MnGe. The crystalline structure was examined in detail by extended X-ray absorption fine structure spectroscopy and anomalous X-ray diffraction. The low-temperature magnetic moment agrees well with the Slater-Pauling rule and indicates a half-metallic ferromagnetic state of the compound, as is predicted by ab-initio calculations. Transport measurements and hard X-ray photoelectron spectroscopy (HAXPES) were performed to explain the electronic structure of the compound.rnA major part of the thesis deals with a systematical investigation of Heusler compounds for thermoelectric applications. Few studies have been reported on thermoelectric properties of p-type Heusler compounds. Therefore, this thesis focuses on the search for new p-type Heusler compounds with high thermoelectric efficiency. The substitutional series NiTi1−xMxSn and CoTi1−xMxSb (where M = Sc, V and 0 ≤ x ≤ 0.2) were synthesized and investigated theoretically and experimentally with respect to electronic structure and transport properties. The results show the possibility to create n-type and p-type thermoelectrics within one Heusler compound. The pure compounds showed n-type behavior, while under Sc substitution the system switched to p-type behavior. A maximum Seebeck coefficient of +230 μV/K (at 350 K) was obtained for NiTi0.26Sc0.04Zr0.35Hf0.35Sn, which is one of the highest values for p-type thermoelectric compounds based on Heusler alloys up to now. HAXPES valence band measurement show massive in gap states for the parent compounds NiTiSn, CoTiSb and NiTi0.3Zr0.35Hf0.35Sn. This proves that the electronic states close to the Fermi energy play a key role for the behavior of the transport properties. Furthermore, the electronic structure of the gapless Heusler compounds PtYSb, PtLaBi and PtLuSb were investigated by bulk sensitive HAXPES. The linear behavior of the spectra close to εF proves the bulk origin of Dirac-cone type density of states. Furthermore, a systematic study on the optical and transport properties of PtYSb is presented. The compound exhibits promising thermoelectric properties with a high figure of merit (ZT = 0.2) and a Hall mobility μh of 300 cm2/Vs at 350 K.rnThe last part of this thesis describes the linear dichroism in angular-resolved photoemission from the valence band of NiTi0.9Sc0.1Sn and NiMnSb. High resolution photoelectron spectroscopy was performed with an excitation energy of hν = 7.938 keV. The linear polarization of the photons was changed using an in-vacuum diamond phase retarder. Noticeable linear dichroism is found in the valence bands and this allows for a symmetry analysis of the contributing states. The differences in the spectra are found to be caused by symmetry dependent angular asymmetry parameters, and these occur even in polycrystalline samples without preferential crystallographic orientation.rnIn summary, Heusler compounds with 1:1:1 and 2:1:1 stoichiometry were synthesized and examined by chemical and physical methods. Overall, this thesis shows that the combination of first-principle calculations, transport measurements and high resolution high energy photoelectron spectroscopy analysis is a very powerful tool for the design and development of new materials for a wide range of applications from spintronic applications to thermoelectric applications.rn

Tin (IV) oxide nanostructures: controlled synthesis, properties and applications in dye-sensitized solar cells

Für viele Anwendungen von Nanomaterialien sind maßgeschneiderte Produkte wün-schenswert, weswegen ein tiefgreifendes und genaues Wissen der Reaktionsabläufe, die zu diesen Produkten führen, unabdingbar ist. Um dies im Fall von SnO2 zu erreichen, behandelt diese Arbeit die kontrollierte Synthese und genaue Charakterisierung von Nanopartikeln von Zinn(IV) Oxid.