Entwicklung neuartiger stickstoffreicher Polyphenylene

Im Rahmen dieser Arbeit wurden Darstellung und elektronische Anwendungsmöglichkeiten von neuartigen stickstoff- und damit elektronenreichen Poly(para-phenylenen) untersucht. Der Teilbereich „Polycarbazole“ befasst sich mit der Synthese von konjugierten (Stufen)leiterpolymeren auf der Basis von Carbazol. Dazu wurde ein neuer und effizienter Syntheseweg zur Gewinnung von 2,7-Dibromcarbazol entwickelt. Durch die weitere Funktionalisierung von 2,7-Dibromcarbazol gelang es, elektronenreiche Leiterpolymere zu gewinnen, die eine grüne Emissionsfarbe aufwiesen. Mit der Verwendung von R = 2-Decyltetradecyl als löslichkeitsfördernder Seitenkette in einem Poly(2,7-carbazol) konnte erstmals ein hochmolekulares Polycarbazol gewonnen werden. Dieses gut lösliche Poly(2,7-carbazol) erwies sich als ein exzellentes Donatormaterial in Solarzellen, welches in Kombination mit dem Farbstoff PDI eine effiziente Solarzelle ergab. Eine OLED mit einem neuartigen arylierten Polycarbazol als Emittermaterial zeigte eine sehr niedrige Turn-on-Spannung und eine intensive blaue EL-Emission. Das Kapitel über imidazolhaltige Poly(para-phenylene) und Discoten stellt die Darstellung von planarisierten Bisimidazolen vor, welche in hohen Ausbeuten durch eine intramolekulare Buchwald-Reaktion zwischen den Imidazolringen und der zentralen Terphenyleinheit durchgeführte wurde. Die dreistufige Darstellung der Discoten aus einem Terephthalaldehyd-Derivat und einem Benzil erlaubt eine einfache sowie variable Einführung von löslichkeitsfördernden Alkylsubstituenten. Auf diese Weise ist der Zugang zu einer völlig neuartigen Klasse an discotischen Materialien möglich, die eine Kombination aus Discoten auf der Basis von Benzolringen (wie z.B. HBC) mit Heteroaromaten darstellen. Die gewonnenen scheibenförmigen Bisimidazole wiesen dementsprechend auf Selbstanordnung zurückzuführende kolumnare Anordnungen und hexagonale Überstrukturen auf. Im dritten Themengebiet wird der Einbau eines Phthalimidchromophors direkt in das Rückgrad von Polyanilin vorgestellt. Da jegliche Veränderung des Oxidationsgrades zu einer unterschiedlichen Donatorfähigkeit des Polyanilinhauptkette führt, variiert in Abhängigkeit davon das Absorptionsverhalten des eingebauten Farbstoffes. Durch die Einführung des Phthalimidchromophores war es zudem möglich, ein leitfähiges Polymer zu erhalten, das im Gegensatz zum nicht-fluoreszierenden Polyanilin eine intensive gelbe Fluoreszenz (lmax = 547 nm) aufweist.

EPR-Spektroskopie zur Untersuchung von Struktur und Dynamik in Polymer-Ton-Nanokompositen

Ziel der vorliegenden Arbeit war die Untersuchung von Struktur und Dynamik in Polymer-Ton-Nanokompositen mittels EPR-Spektroskopie; damit sollten ein Beitrag zur Analyse der Tensidschicht in solchen Systemen geleistet und die Ergebnisse anderer Messmethoden ergänzt werden. Die Tensidschicht in Polymer-Ton-Nanokompositen nimmt großen Einfluss auf das System, denn sie bestimmt die Wechselwirkung zwischen Ton und Polymer: Damit hydrophiler Ton gut mit hydrophobem Polymer (hier Polystyrol) mischbar ist, muss das Schichtsilikat zunächst mit Tensiden organisch-modifiziert werden; dies geschieht durch Kationenaustausch der Natriumionen im Ton gegen Tenside. Um mit Hilfe der EPR einen Einblick in die Tensidschicht zu gewinnen, muss etwa 1% der zur Tonmodifizierung eingesetzten Amphiphile spinmarkiert sein. So gelang es im Rahmen dieser Arbeit, Tenside mit verschiedenen Kopfgruppen, nämlich Trimethylammonium- bzw. Trimethylphosphoniumtenside, zu synthetisieren und sie an verschiedenen Positionen ihrer hydrophoben Alkylkette mit einem Nitroxidradikal zu markieren. Das Nitroxidradikal diente als Spinsonde für die EPR-Experimente. Neben der Synthese verschiedener, spinmarkierter Amphiphile, der anschließenden Darstellung organisch-modifizierten Tons (Kationenaustausch) und verschiedener Polymer-Ton-Nanokomposite (Schmelzinterkalation) wurden alle Proben mittels EPR-Spektroskopie untersucht; dabei wurden sowohl cw- als auch gepulste Messtechniken eingesetzt. Aus cw-Experimenten ging hervor, dass die Dynamik der gesamten Tensidschicht mit der Temperatur zunimmt und die Mobilität der hydrophoben Tensidalkylkette mit wachsendem Abstand zu ihrer Kopfgruppe wächst. Zugabe von Polymer behindert bei steigender Temperatur das Anschwellen des Tons bei Aufschmelzen der Tensidschicht; die Dynamik des Systems ist eingeschränkt. Mit Hilfe gepulster EPR-Messungen (ENDOR und ESEEM), die Informationen über Abstände bzw. Kontakt in den untersuchten Systemen lieferten, ließ sich ein Strukturmodell der Polymer-Ton-Nanokomposite skizzieren, das Vorstellungen anderer, älterer Methoden unterstützt: Hierbei richten sich die Tenside in Multischichten unterschiedlicher Mobilität parallel zur Tonoberfläche aus.

Discotic materials for organic electronics

Die Kontrolle der ausgeprägten Aggregationsfähigkeit von alkylsubstituierten Hexa-peri-hexabenzocoronenen (HBC) wurde durch die Reduktion der intermolekularen Wechselwirkungen erreicht. Sterisch anspruchsvolle, verzweigte Alkylketten, mit einem Verzweigungspunkt naher des aromatischen Kerns, wurden in die Corona der aromatischen Scheiben eingebracht und verleihen den Derivaten Schmelzbarkeit ohne thermische Zersetzung. Dies erlaubte eine kostengünstige Verarbeitungstechniken direkt aus der Schmelze wie z.B. Zonenschmelzen, um uniaxial organisierte makroskopische Filme zu erhalten. Abhängig von dem sterischen Anspruch, der durch die Seitenkette erzeugt wird, wurden unterschiedliche molekulare Orientierungen auf Oberflächen erhalten, was eine wichtige Voraussetzung ist, um diskotische Materialien in elektronische Bauteile zu implementieren. Eine weitere Voraussetzung sind hohe Ladungsträgerbeweglichkeiten und Ladungsträgerlebenszeiten in den Halbleitermaterialien, die mit time-resolved pulse-radiolysis microwave conductivity (TR-PRMC) und time-of-flight (TOF) auch für die synthetisieren Materialien bestimmt wurden. Die neuen Materialien zeigten bereits in organischen Solarzellen gute Leistungen. Den Einfluss des Perimeters auf die elektronischen Eigenschaften der polyzyklischen aromatischen Kohlenwasserstoffe (PAKs) wurde theoretisch vorhergesagt und in dieser Arbeit durch die Synthese einer homologe Serie von PAKs experimentell bestätigt. Geht man von der „arm-chair“ Peripherie des HBC sukzessive zu einer partiellen „zickzack“ Peripherie, so findet man eine Abhängigkeit der elektronischen Banden von Symmetrie und Größe des aromatischen Systems. Die spontan ausgebildete Überstruktur dieser Derivate zeigte eine Abhängigkeit von Substitutionsmuster und der Natur der Alkylketten. Zusammenfassend wurden neben der Synthese von neuartigen Materialien für den Einsatz in der organischen Elektronik Synthesen entwickelt, die eine vereinfachte Funktionalisierung von ausgedehnten PAKs ermöglicht. Diese Konzepte erlauben eine Justierung der molekularen und supramolekularen Eigenschaften, eines der wichtigsten Voraussetzungen für den Einsatz von Materialien in elektronischen Bauelementen.

Synthetical engineering of supramolecular properties of large polycyclic aromatic hydrocarbons

An important property for devices is the charge-carrier mobility values for discotic organic materials like hexa-peri-hexabenzocoronenes. A close relation exists between the degree of their columnar self-arrangement of the molecules and their mobilities. Within this first step an induction of a higher order via hydrogen-bonding was considered, which mainly pointed towards the improvement of the intracolumnar stacking of the materials. For the analytics a broad range of methods was used including differential scanning calorimetry (DSC), wide-angle X-ray diffractometry (WAXS), solid-state NMR spectroscopy and scanning tunneling microscopy (STM). Indeed, a specific influence of the hydrogen-bonds could be identified, although in several cases by the cost of a severe reduction of solubility and processability. This effect was dampened by the addition of a long alkyl chain next to the hydrogen-bond exerting functional group, which resulted in an improved columnar arrangement by retention of processability. In contrast to the before mentioned example of inducing a higher intracolumnar order by hydrogen-bonding, the focus was also be set upon larger aromatic systems. The charge-carrier mobility is also in close relation to the size of the aromatic core and larger π-areas are expected to lead to improved mobilities. For photovoltaic applications a high extinction coefficient over a broad range of the spectrum is favorable, which can also be achieved by enlarging the aromatic core component. In addition the stronger π-interactions between the aromatic core components should yield an improved columnar stability and order. However the strengthening of the π-interactions between the aromatic core components led to a reduction of the solubility and the processability due to the stronger aggregation of the molecules. This required the introduction of efficiently solubilizing features in terms of long alkyl chains in the corona of the aromatic entity, in combination of a distortion of the aromatic core moiety by bulky tert-butyl groups. By this approach not only the processing and cleaning of the materials with standard laboratory techniques became possible, but moreover the first structure-rich UV/vis and a resolved 1H-NMR spectra for an aromatic system two times larger than hexa-peri-hexabenzocoronene were recorded. The bulk properties in an extruded fiber as well as on the surface showed a columnar self-assembly including a phase in which a homeotropic alignment on a substrate was observed, which turns the material into an interesting candidate for future applications in electronic devices.

Die Synthese von Glycopeptiden und Glycopeptid-Protein-Konjugaten mit einer Partialstruktur des tumorassoziierten Mucins MUC1 zur Entwicklung von Tumorvakzinen

„Synthese von Glycopeptiden und Glycopeptid-Protein-Konjugaten mit einer Partialstruktur des tumorassoziierten Mucins MUC1 zur Entwicklung von Tumorvakzinen“ Das Glycoprotein MUC1 ist in Tumorepithelzellen sonderlich stark überexprimiert und wegen der vorzeitig einsetzenden Sialylierung sind die Saccharid-Epitope der O-Glycanketten stark verkürzt (sog. tumorassoziierte Antigene). Dadurch werden auch bisher verborgene Peptidepitope des Glycoprotein-Rückgrates auf der Zelloberfläche der Epithelzellen zugänglich, die als fremd von den Zellen des Immunsystems erkannt werden können. Dies macht das MUC1-Zelloberfächenmolekül zu einem Zielmolekül in der Entwicklung von Tumorvakzinen. Diese beiden strukturellen Besonderheiten wurden in der Synthese von Glycohexadecapeptiden verbunden, indem die veränderten tumorassoziierten Saccharidstrukturen TN-, STN- und T-Antigen als Glycosylaminosäure-Festphasenbausteine synthetisiert wurden und in das Peptidepitop der Wiederholungseinheit des MUC1 durch Glycopeptid-Festphasensynthese eingebaut wurden. Wegen der inhärenten schwachen Immunogenität der kurzen Glycopeptide müssen die synthetisierten Glycopeptidstrukturen an ein Trägerprotein, welches das Immunsystem stimuliert, gebunden werden. Zur Anbindung der Glycopeptide ist ein selektives Kupplungsverfahren nötig, um definierte und strukturell einheitliche Glycopeptid-Protein-Konjugate zu erhalten. Es konnte eine neue Methode entwickelt werden, bei der die Konjugation durch eine radikalische Additionsreaktion von als Allylamide funktionalisierten Glycopeptiden an ein Thiol-modifiziertes Trägerprotein erfolgte. Dazu wurde anhand von synthetisierten, als Allylamide modifizierten Modellaminosäuren untersucht, ob diese Reaktion generell für eine Biokonjugation geeignet ist und etwaige Nebenreaktionen auftreten können. Mit dieser Methode konnten verschiedene MUC1-Glycopeptid-Trägerprotein-Konjugate hergestellt werden, deren immunologische Untersuchung noch bevorsteht. Das tumorassoziierte MUC1 nimmt in der immundominanten Region seiner Wiederholungseinheit eine knaufartige Struktur ein. Für die Entwicklung von selektiven Tumorvakzinen ist es von großer Bedeutung möglichst genau die Struktur der veränderten Zelloberflächenmoleküle nachzubilden. Durch die Synthese von cyclischen (Glyco)Peptiden wurde dieses Strukturelement fixiert. Dazu wurden olefinische Aminosäure Festphasenbausteine hergestellt, die zusammen mit den oben genannten Glycosylaminosäuren mittels einer Glycopeptid-Festphasensynthese in acyclische Glycopeptide eingebaut wurden. Diese wurden dann durch Ringschlussmetathese zyklisiert und im Anschluss reduziert und vollständig deblockiert. In einem dritten Projekt wurde der Syntheseweg zur Herstellung einer C-Glycosylaminosäure mit einer N-Acetylgalactosamin-Einheit entwickelt. Wichtige Schritte bei der von Glucosamin ausgehenden Synthese sind die Keck-Allylierung, eine Epimerisierung, die Herstellung eines Brom-Dehydroalanin-Derivates und eine B-Alkyl-Suzuki-Miyaura-Kreuzkupplung sowie Schutzgruppenoperationen. Der racemische Baustein konnte dann in der Peptid-Festphasensynthese eines komplexen MUC1-Tetanustoxin-Konjugates eingesetzt werden.

Nitrogen-bridged polyphenylene-based materials for electronic applications

Conjugated polymers are macromolecules that possess alternating single and double bonds along the main chain. These polymers combine the optoelectronic properties of semiconductors with the mechanical properties and processing advantages of plastics. In this thesis we discuss the synthesis, characterization and application of polyphenylene-based materials in various electronic devices. Poly(2,7-carbazole)s have the potential to be useful as blue emitters, but also as donor materials in solar cells due to their better hole-accepting properties. However, it is associated with two major drawbacks (1) the emission maximum occurs at 421 nm where the human eye is not very sensitive and (2) the 3- and 6- positions of carbazole are susceptible to chemical or electrochemical degradation. To overcome these problems, the ladder-type nitrogen-bridged polymers are synthesized. The resulting series of polymers, nitrogen-bridged poly(ladder-type tetraphenylene), nitrogen-bridged poly(ladder-type pentaphenylene), nitrogen-bridged poly(ladder-type hexaphenylene) and its derivatives are discussed in the light of photophysical and electrochemical properties and tested in PLEDs, solar cell, and OFETs. A promising trend which has emerged in recent years is the use of well defined oligomers as model compounds for their corresponding polymers. However, the uses of these molecules are many times limited by their solubility and one has to use vapor deposition techniques which require high vacuum and temperature and cannot be used for large area applications. One solution to this problem is the synthesis of small molecules having enough alkyl chain on the backbone so that they can be solution or melt processed and has the ability to form thin films like polymers as well as retain the high ordered structure characteristics of small molecules. Therefore, in the present work soluble ladderized oligomers based on thiophene and carbazole with different end group were made and tested in OFET devices. Carbazole is an attractive raw material for the synthesis of dyes since it is cheap and readily available. Carbazoledioxazine, commercially known as violet 23 is a representative compound of dioxazine pigments. As part of our efforts into developing cheap alternatives to violet 23, the synthesis and characterization of a new series of dyes by Buchwald-type coupling of 3-aminocarbazole with various isomers of chloroanthraquinone are presented.

Synthesis and characterization of new discotic polycyclic aromatic hydrocarbons and related pyrolytic nanostructures

Diskotische Hexa-peri-hexabenzocoronene (HBC) als molekulare, definierte graphitische Substrukturen sind bereits seit langem Gegenstand von Untersuchungen zu der Delokalisierung von π-Elektronen. In dieser Arbeit wurden zusätzlich Platin-Komplexe in das periphere Substitutionsmuster von HBC eingeführt. Dies führte zu einer Verbesserung der Emission von dem angeregten Triplett-Zustand in den Singulett-Grundzustand mit einer zusätzlichen Verlängerung der Lebensdauer des angeregten Zustandes. Zusätzlich erlaubte diese Konfiguration ein schnelles Intersystem-Crossing mittels einer verstärkten Spin-Orbit Kopplung, die sowohl bei tiefen Temperaturen, als auch bei Raumtemperatur exklusiv zu Phosphoreszenz (T1→S0) führte. Das Verständniss über solche Prozesse ist auch essentiell für die Entwicklung verbesserter opto-elektronischer Bauteile. Die Erstellung von exakt definierten molekularen Strukturen, die speziell für spezifische Interaktionen hergestellt wurden, machten eine Inkorporation von hydrophoben-hydrophilen, wasserstoffverbrückten oder elektrostatischen funktionalisierten Einheiten notwendig, um damit den supramolekularen Aufbau zu kontrollieren. Mit Imidazolium-Salzen funktionalisierte HBC Derivate wurden zu diesem Zwecke hergestellt. Eine interessante Eigenschaft dieser Moleküle ist ihre Amphiphilie. Dies gestattete die Untersuchung ihrer Eigenschaften in einem polaren Solvens und sowohl der Prozessierbarkeit als auch der Faserbildung auf Siliziumoxid-Trägern. Abhängig vom Lösungsmittel und der gewählten Konditionen konnten hochkristalline Fasern erhalten werden. Durch eine Substitution der HBCs mit langen, sterisch anspruchsvollen Seitenketten, konnte durch eine geeignete Prozessierung eine homöotrope Ausrichtung auf Substraten erreicht werden, was dieses Material interessant für photovoltaische Applikationen macht. Neuartige Polyphenylen-Metall-Komplexe mit diskotischen, linearen und dendritischen Geometrien wurden mittels einer einfachen Reaktion zwischen Co2(CO)8 und Ethinyl-Funktionalitäten in Dichlormethan hergestellt. Nach der Pyrolyse dieser Komplexe ergaben sich unterschiedliche Kohlenstoff-Nanopartikel, inklusive Nanoröhren, graphitischen Nanostäben und Kohlenstoff/Metall Hybrid Komplexe, die durch Elektronenmikroskopie untersucht wurden. Die resultierenden Strukturen waren dabei abhängig von der Zusammensetzung und Struktur der Ausgangssubstanzen. Anhand dieser Resultate ergeben sich diverse Möglichkeiten, um den Mechanismus, der zur Herstellung graphitischer Nanopartikel führt, besser zu verstehen.

Photovoltaics from discotic liquid crystalline HBCs & poly(2,7-carbazole)s

In this study, the use of the discotic liquid crystalline HBCs and conjugated polymers based on 2,7-carbazole were investigated in detail as donor materials in organic bulk-heterojunction solar cells. It has been shown that they perform efficiently in photovoltaic devices in combination with suitable acceptors. The efficiency was found to depend strongly dependent on the morphology of the film. By investigation of a series of donor materials with similar molecular structures based on both discotic molecules and conjugated polymers, a structure-performance relation was established, which is not only instructive for these materials but also serves as a guideline for improved molecular design. For the series of HBCs used in this study, it is found that the device efficiency decreases with increasing length of the alkyl substituents in the HBC. Thus, the derivative with the smallest alkyl mantle, being more crystalline compared to the HBCs with longer alkyl chains, gave the highest EQE of 12%. A large interfacial separation was found in the blend of HBC-C6,2 and PDI, since the crystallization of the acceptor occurred in a solid matrix of HBC. This led to small dispersed organized domains and benefited the charge transport. In contrast, blends of HBC-C10,6/PDI or HBC-C14,10/PDI revealed a rather homogeneous film limiting the percolation pathways due to a mixed phase. For the first time, poly(2,7-carbazole) was incorporated as a donor material in solar cells using PDI as an electron acceptor. The good fit in orbital energy levels and absorption spectra led to high efficiency. This result indicates that conjugated polymers with high band-gap can also be applied as materials to build efficient solar cells if appropriate electron acceptors are chosen. In order to enhance the light absorption ability, new ladder-type polymers based on pentaphenylene and hexaphenylene with one and three nitrogen bridges per repeat unit have been synthesized and characterized. The polymer 2 with three nitrogen bridges showed more red-shifted absorbance and emission and better packing in the solid-state than the analogous polymer 3 with only one nitrogen bridge per monomer unit. An overall efficiency as high as 1.3% under solar light was obtained for the device based on 1 and PDI, compared with 0.7% for the PCz based device. Therefore, the device performance correlates to a large extent with the solar light absorption ability and the lateral distance between conjugated polymer chains. Since the lateral distance is determined by the length and number of attached alkyl side chains, it is possible to assume that these substituents insulate the charge carrier pathways and decrease the device performance. As an additional consequence, the active semiconductor is diluted in the insulating matrix leading to a lower light absorption. This work suggests ways to improve device performance by molecular design, viz. maintaining the HOMO level while bathochromically shifting the absorption by adopting a more rigid ladder-type structure. Also, a high ratio of nitrogen bridges with small alkyl substituents was a desirable feature both in terms of adjusting the absorption and maintaining a low lateral inter-chain separation, which was necessary for obtaining high current and efficiency values.

Structuring of polymer surface by evaporation of sessile microdrops

In this thesis, we investigated the evaporation of sessile microdroplets on different solid substrates. Three major aspects were studied: the influence of surface hydrophilicity and heterogeneity on the evaporation dynamics for an insoluble solid substrate, the influence of external process parameters and intrinsic material properties on microstructuring of soluble polymer substrates and the influence of an increased area to volume ratio in a microfluidic capillary, when evaporation is hindered. In the first part, the evaporation dynamics of pure sessile water drops on smooth self-assembled monolayers (SAMs) of thiols or disulfides on gold on mica was studied. With increasing surface hydrophilicity the drop stayed pinned longer. Thus, the total evaporation time of a given initial drop volume was shorter, since the drop surface, through which the evaporation occurs, stays longer large. Usually, for a single drop the volume decreased linearly with t1.5, t being the evaporation time, for a diffusion-controlled evaporation process. However, when we measured the total evaporation time, ttot, for multiple droplets with different initial volumes, V0, we found a scaling of the form V0 = attotb. The more hydrophilic the substrate was, the more showed the scaling exponent a tendency to an increased value up to 1.6. This can be attributed to an increasing evaporation rate through a thin water layer in the vicinity of the drop. Under the assumption of a constant temperature at the substrate surface a cooling of the droplet and thus a decreased evaporation rate could be excluded as a reason for the different scaling exponent by simulations performed by F. Schönfeld at the IMM, Mainz. In contrast, for a hairy surface, made of dialkyldisulfide SAMs with different chain lengths and a 1:1 mixture of hydrophilic and hydrophobic end groups (hydroxy versus methyl group), the scaling exponent was found to be ~ 1.4. It increased to ~ 1.5 with increasing hydrophilicity. A reason for this observation can only be speculated: in the case of longer hydrophobic alkyl chains the formation of an air layer between substrate and surface might be favorable. Thus, the heat transport to the substrate might be reduced, leading to a stronger cooling and thus decreased evaporation rate. In the second part, the microstructuring of polystyrene surfaces by drops of toluene, a good solvent, was investigated. For this a novel deposition technique was developed, with which the drop can be deposited with a syringe. The polymer substrate is lying on a motorized table, which picks up the pendant drop by an upward motion until a liquid bridge is formed. A consecutive downward motion of the table after a variable delay, i.e. the contact time between drop and polymer, leads to the deposition of the droplet, which can evaporate. The resulting microstructure is investigated in dependence of the processes parameters, i.e. the approach and the retraction speed of the substrate and the delay between them, and in dependence of the intrinsic material properties, i.e. the molar mass and the type of the polymer/solvent system. The principal equivalence with the microstructuring by the ink-jet technique was demonstrated. For a high approach and retraction speed of 9 mm/s and no delay between them, a concave microtopology was observed. In agreement with the literature, this can be explained by a flow of solvent and the dissolved polymer to the rim of the pinned droplet, where polymer is accumulated. This effect is analogue to the well-known formation of ring-like stains after the evaporation of coffee drops (coffee-stain effect). With decreasing retraction speed down to 10 µm/s the resulting surface topology changes from concave to convex. This can be explained with the increasing dissolution of polymer into the solvent drop prior to the evaporation. If the polymer concentration is high enough, gelation occurs instead of a flow to the rim and the shape of the convex droplet is received. With increasing delay time from below 0 ms to 1s the depth of the concave microwells decreases from 4.6 µm to 3.2 µm. However, a convex surface topology could not be obtained, since for longer delay times the polymer sticks to the tip of the syringe. Thus, by changing the delay time a fine-tuning of the concave structure is accomplished, while by changing the retraction speed a principal change of the microtopolgy can be achieved. We attribute this to an additional flow inside the liquid bridge, which enhanced polymer dissolution. Even if the pendant drop is evaporating about 30 µm above the polymer surface without any contact (non-contact mode), concave structures were observed. Rim heights as high as 33 µm could be generated for exposure times of 20 min. The concave structure exclusively lay above the flat polymer surface outside the structure even after drying. This shows that toluene is taken up permanently. The increasing rim height, rh, with increasing exposure time to the solvent vapor obeys a diffusion law of rh = rh0  tn, with n in the range of 0.46 ~ 0.65. This hints at a non-Fickian swelling process. A detailed analysis showed that the rim height of the concave structure is modulated, unlike for the drop deposition. This is due to the local stress relaxation, which was initiated by the increasing toluene concentration in the extruded polymer surface. By altering the intrinsic material parameters i.e. the polymer molar mass and the polymer/solvent combination, several types of microstructures could be formed. With increasing molar mass from 20.9 kDa to 1.44 MDa the resulting microstructure changed from convex, to a structure with a dimple in the center, to concave, to finally an irregular structure. This observation can be explained if one assumes that the microstructuring is dominated by two opposing effects, a decreasing solubility with increasing polymer molar mass, but an increasing surface tension gradient leading to instabilities of Marangoni-type. Thus, a polymer with a low molar mass close or below the entanglement limit is subject to a high dissolution rate, which leads to fast gelation compared to the evaporation rate. This way a coffee-rim like effect is eliminated early and a convex structure results. For high molar masses the low dissolution rate and the low polymer diffusion might lead to increased surface tension gradients and a typical local pile-up of polymer is found. For intermediate polymer masses around 200 kDa, the dissolution and evaporation rate are comparable and the typical concave microtopology is found. This interpretation was supported by a quantitative estimation of the diffusion coefficient and the evaporation rate. For a different polymer/solvent system, polyethylmethacrylate (PEMA)/ethylacetate (EA), exclusively concave structures were found. Following the statements above this can be interpreted with a lower dissolution rate. At low molar masses the concentration of PEMA in EA most likely never reaches the gelation point. Thus, a concave instead of a convex structure occurs. At the end of this section, the optically properties of such microstructures for a potential application as microlenses are studied with laser scanning confocal microscopy. In the third part, the droplet was confined into a glass microcapillary to avoid evaporation. Since here, due to an increased area to volume ratio, the surface properties of the liquid and the solid walls became important, the influence of the surface hydrophilicity of the wall on the interfacial tension between two immiscible liquid slugs was investigated. For this a novel method for measuring the interfacial tension between the two liquids within the capillary was developed. This technique was demonstrated by measuring the interfacial tensions between slugs of pure water and standard solvents. For toluene, n-hexane and chloroform 36.2, 50.9 and 34.2 mN/m were measured at 20°C, which is in a good agreement with data from the literature. For a slug of hexane in contact with a slug of pure water containing ethanol in a concentration range between 0 and 70 (v/v %), a difference of up to 6 mN/m was found, when compared to commercial ring tensiometry. This discrepancy is still under debate.

Synthesis, characterization and chemical modification of a cationic polyelectrolyte poly(methylene amine)

Polyamine polymers have attracted attention due to their ability to demonstrate pH dependent cationic nature and presence of highly reactive pendant amino groups. These amino groups make them suitable for a host of applications through cross-linking and derivatization. As a result the end use application of a polyamine is largely driven by the number of amino groups and the way they are attached to the polymer backbone. Thus, this piece of work describes the synthesis and investigation of properties of a novel aliphatic polyamine, poly(methylene amine); that carries maximum number of amino group on its backbone. The target polymer, poly(methylene amine); was synthesized via two major steps viz.1.synthesis of precursor polymers of poly(methylene amine) and 2. Hydrolysis of the precursor polymers to obtain poly(methylene amine). The precursor polymers poly (1,3-diacetylimidazole-2-one)(6) and poly(1,3-diformyldihydroimidazol-2-one)(7) were synthesized via radical polymerization of their respective monomers. The monomers were polymerized in bulk as well as in solution at different reaction conditions. The maximum molecular weights were achieved by polymerizing the monomers in bulk (Mn = 6.5 x 104 g/mol and Mw = 2.13 x 105 g/mol) of 6. The precursor polymers were hydrolyzed under strong reaction conditions in ethanol in presence of NaOH, LiCl at 170°C to yield poly(methylene amine). The process of hydrolysis was monitored by IR spectroscopy. The solution properties of poly(methylene amine) and its hydrochloride were investigated by viscosimetry and light scattering. The reduced viscosity of poly (methylene amine) hydrochloride as a function of polymer concentration demonstrated a behavior typical of cationic polyelectrolyte. With decrease in polymer concentration the reduced viscosity of poly(methylene amine) hydrochloride increased gradually. The dynamic light scattering studies also revealed behaviors of a polyelectrolyte. Poly(methylene amine) was reacted with electrophiles to yield novel materials. While the attachment of alkyl group onto the nitrogen would increase nucleophilicity, it would also impose steric hindrance. As a result the degree of substitution on poly(methylene amine) would be governed by both the factors. Therefore, few model reactions with electrophiles were performed on polvinylamine under similar reaction conditions in order to make a comparative evaluation. It was found that under similar reaction conditions the degree of substitution was higher in case of polyvinylamine in comparison with poly (methylene amine).This shows that the steric hindrance outweighs nucleophilicity while deciding degree of substitution of electrophiles on poly(methylene amine). The modification was further extended to its use as an initiator for ring opening polymerization of benzyloxy protected N-carboxyanhydride of z-Lysine. The resulting polymer had an interesting brush like architecture. The solid state morphology of this polymer was investigated by SAXS. The 2D-WAXS diffractograms revealed hexagonal morphology of peptide segments without formation of alpha helices.

Supramolecular order and dynamics of functional materials studied by solid state NMR

The goal of this thesis was the investigation of the structure, conformation, supramolecular order and molecular dynamics of different classes of functional materials (phthalocyanine, perylene and hexa-peri-hexabenzocoronene derivatives and mixtures of those), all having planar aromatic cores modified with various types of alkyl chains. The planar aromatic systems are known to stack in the solid and the liquid-crystalline state due to p-p interactions forming columnar superstructures with high one-dimensional charge carrier mobility and potential application in photovoltaic devices. The different functionalities attached to the aromatic cores significantly influence the behavior of these systems allowing the experimentalists to modify the structures to fine-tune the desired thermotropic properties or charge carrier mobility. The aim of the presented studies was to understand the interplay between the driving forces causing self-assembly by relating the structural and dynamic information about the investigated systems. The supramolecular organization is investigated by applying 1H solid state NMR recoupling techniques. The results are related with DSC and X-ray scattering data. Detailed information about the site-specific molecular dynamics is gained by recording spinning sideband patterns using 1H-1H and 13C-1H solid state NMR recoupling techniques. The determined dipole-dipole coupling constants are then related with the coupling constants of the respective rigid pairs, thus providing local dynamic order parameters for the respective moieties. The investigations presented reveal that in the crystalline state the preferred arrangement in the columnar stack of discotic molecules modified with alkyl chains is tilted. This leads to characteristic differences in the 1H chemical shifts of otherwise chemically equivalent protons. Introducing branches and increasing the length of the alkyl chains results in lower mesophase transitions and disordered columnar stacks. In the liquid-crystalline state some of the discs lose the tilted orientation, others do not, but all start a rapid rotation about the columnar axis.

Spin-crossover in metallomesogens of iron(II)

Covalent grafting mesogenic groups to the coordination cores of the parent mononuclear low-spin and spin-crossover compounds afforded metallomesogenic complexes of iron(II). In comparison with the parent complexes the spin-crossover properties of the alkylated derivatives are substantially modified. The type of the modification was found to be dependent on the properties of the parent system and the nature of the used anion, however, the general tendency is the destabilization of the low-spin state at the favor of spin-crossover or high-spin behavior below 400 K. The structural insight revealed the micro-segregated layered organization. The effect of the alkylation of the parent compounds consists first of all in the change of the lattice to a two-dimensional lamellar one retaining significant intermolecular contacts only within the ionic bilayers. The comprehensive analysis of the structural and thermodynamic data in the homologous series pointed at the mechanism of the interplay between the structural modification on melting and the induced anomalous change of the magnetic properties. A family of one-dimensional spin-crossover polymers was synthesized and characterized using a series of spectroscopic methods, X-ray powder diffraction, magnetic susceptibility measurements and differential scanning calorimetry. The copper analogue of was also synthesized and its crystal structure solved. In comparison with the mononuclear systems, the polymeric mesogens of iron(II) are less sensitive to the glass transition, which was attributed to the moderate concomitant variation of the structure. Nevertheless, the observed increase of the magnetic hysteresis with lengthening of the alkyl substituents was ascribed to the interplay of the structural reorganization of the coordination core due to spin-crossover with the structural delay in the spatial reorganization of the mesogenic substituents. The classification of mononuclear and polymeric metallomesogens according to the interactions between the structural- and the spin-transition and analysis of the data on the reported spin-crossover metallomesogens led to the separation of three types, namely: Type i: systems with coupling between the electronic structure of the iron(II) ions and the mesomorphic behavior of the substance; Type ii: systems where both transitions coexist in the same temperature region but are not coupled due to competition with the dehydration or due to negligible structural transformation; Type iii: systems where both transitions occur in different temperature regions and therefore are uncoupled. Fine-tuning, in particular regarding the temperature at which the spin-transition occurs with hysteresis properties responsible for the memory effect, are still a major challenge towards practical implementation of spin-crossover materials. A possible answer to the problem could be materials in which the spin-crossover transition is coupled with another transition easily controllable by external stimuli. In the present thesis we have shown the viability of the approach realized in the mesogenic systems with coupled phase- and spin-transitions.

C 3-symmetric discotic liquid crystalline materials for molecular electronics: versatile synthesis and self-organization

This thesis presents the versatile synthesis and self-organization of C3-symmetric discotic nanographene molecules as well as their potential applications as materials in molecular electronics. The details can be described as follows: 1) A novel synthetic strategy towards properly designed C3 symmetric 1,3,5-tris-2’arylbenzene precursors has been developed. After the final planarization by treatment with FeCl3 under mild conditions, for the first time, it became possible to access a variety of new C3-symmetric hexa-peri-hexabenzocoronenes (HBCs) and a series of triangle-shaped nanographenes. D3 symmetric HBC with three alkyl substituents and C2 symmetric HBC with two alkyl substituents were synthesized and found to show the surprising decrease of isotropic points., the self-assembly at the liquid-solid interface displayed a unique zigzag and flower patterns. 2) Triangle-shaped discotics revealed a unique self-assembly behavior in solution, solid state as well as at the solution-substrate interface. A mesophase stability over the broad temperature range with helical supramoelcular arrangement were observed in the bulk state. The honeycomb pattern as the result of novel self-assembly was presented. Triangle-shaped discotics with swallow alkyl tails were fabricated into photovoltaic devices, the supramolecular arrangement upon thermal treatment was found to play a key role in the improvement of solar efficiency. 3) A novel class of C3 symmetric HBCs with alternating polar/apolar substituents was synthesized. Their peculiar self-assembly in solution, in the bulk and on the surface were investigated by NMR techniques, X-ray diffraction as well as different electron microscope techniques. 4) A novel concept for manipulating the intracolumnar stacking of discotics and thus for controlling the helical pitch was presented. A unique staggered stacking in the column was achieved for the first time. Theoretical simulations confirmed this self-organization and predicted that this packing should show the highest charge carrier mobility for all discotics.

Heteroatom containing polycyclic aromatic hydrocarbons with positive charge - synthesis and characterization

The synthesis and characterization of various heteroatom containing PAHs with positive charge were investigated in this work: 1. A series of 2-phenyl-benzo[8,9]quinolizino[4,5,6,7-fed]phenanthridinylium (PQP) salts with different alkyl chains and anions were synthesized. The synthesis of the extended derivates of PQP salts with two fused benzene rings, 2-phenyl-naphthacene[1,2]quinolizino[3,4,5,6-def]benzo[i]phenanthridinium (DBPQP) tetrafluoroborate was also developed. The self-assembly behavior of these amphiphilic PAHs was investigated in methanolic solution as well as in the bulk. Various aggregates with different morphologies such as fibers, tubes and vesicals were obtained from their solution. All of these morphology changes could be ascribed to the changes in intermolecular interactions which resulting from the difference in the molecular structures such as aromatic cores, alkyl chains and counterions. 2. The synthetic strategy of oxygen containing positively charged PAHs, benzo[5,6]naphthaceno[1,12,11,10-jklmna]xanthylium (BNAX) salts and its dibenzo derivates, DBNAX salts were developed. With a similar method, sulfur containing benzo[5,6]naphthaceno[1,12,11,10-jklmna]thioxanthylium (BNATX) salts were also synthesized. Various BNAX salts with different alkyl chains could be obtained and their supramolecular behavior were investigated. A discotic liquid crystalline behavior was observed for di- (3-25) and tridodecyl (3-27) substituted BNAX salts and both compounds exhibited large unit cell in their 2D-WAXS patterns which could be attributed to the formation of dimer structures. By drop casting their methanolic solution on silicon wafers, similar nanoscaled fibers from monododecyl substituted BNAX bromide 3-24 and DBNAX bromide 3-35 could be observed. 3. A novel synthetic method toward nitrogen containing 14-phenyl-dibenzo[jk,mn]naphtho[2,1,8-fgh]thebenidinium (DBNT) salts was also developed. In this method, the undehydrogenated precursor of DBNT, dibenzoacridinium salt could be produced directly from the reaction between dibenzoxanthenylium derivates and amine/aniline in reasonable yields. Various DBNT salts with different alkyl and alkylphenyl chains on their nitrogen atom were synthesized in this two-step method. The self-assembly behavior of two alkylated DBNT salts, 4-15a and 4-18b was also studied in this work. Compound 4-15a formed nanoscaled fibers and helical aggregates were obtained from 4-18b in their methanolic solutions. 4. Various ionic complexes were derived by complexing PQP and DBPQP cations with different sulfate/sulfonate group containing anionic surfactants. The ionic complexes resulting from the ionic self-assembly (ISA) method exhibited self-assembly behavior which was controllable by the species and shape of cations and anions. Various aggregates such as nanofibers and spherical aggregates could be produced from their methanolic solution in a defined manner conveniently.

Terrylendiimide als Biolabel und funktionelle Farbstoffe

In dieser Arbeit werden neue Rylenimide und Anwendungsmöglichkeiten für diese Farbstoffklasse beschrieben, die sich durch hohe Photostabilitäten und hohe Fluoreszenzquantenausbeute auszeichnet. Ziel dieser Arbeit war es, durch systematische Wahl der Substituenten in den Imidstrukturen und/oder den bay-Regionen von Rylendiimidfarbstoffen vollkommen neue Produkteigenschaften zu verwirklichen, Reaktionen bzw. Anwendungen zu ermöglichen und den Aufbau von komplexeren Chromophorarchitekturen zu gestatten. Das Strukturmotiv des Terrylendiimids nahm dabei die zentrale Rolle ein. Die Arbeit wurde in vier Kapitel aufgeteilt. Das Ziel des ersten Kapitels war es, wasserlösliche Terrylendiimide zur Untersuchung von biologischen Proben im Wellenlängenbereich über 600 nm einzusetzen. Ein wasserlösliches Terrylendiimid erwies sich dabei als deutlich photostabiler als zwei weitverbreitete Fluoreszenzfarbstoffe. Eine erste Proteinmarkierung mit monofunktionellem Farbstoff wurde an Proteinmolekülen erfolgreich durchgeführt. Durch gezielte Modifikationen konnten zwei Terrylendiimide hergestellt werden, die sich noch deutlich besser zum Abbilden von Zellstrukturen eignen. In dem zweiten Kapitel spielte die Löslichkeit von Rylendiimiden in organischen Lösungsmitteln eine zentrale Rolle. Es wurde eine Rylendiimidserie hergestellt, deren löslichkeitssteigernde Gruppen eine Organisation der Moleküle in ausgedehnten Stapelstrukturen nicht verhindern. Mit dieser Serie konnte das flüssigkristalline Verhalten und die Selbstorganisation in der Rylendiimidreihe untersucht werden. Aufbauend auf diesen Ergebnissen wurde die Selbstorganisation der Diimide in Donor-Akzeptor Gemischen untersucht. In STM-Experimenten konnten für alle drei Diimide selbstorganisierte Monoschichten mit dem Rastertunnelmikroskop mit molekularer Auflösung abgebildet werden. Darüber hinaus wurden in diesem Kapitel die ersten organischen Feldeffekttransistoren (OFET) auf der Basis des synthetisierten Terrylendiimids beschrieben. Im Rahmen eines Projektes in dem die elektronische Energieübertragung in Donor-Akzeptor-Diaden mit Hilfe von Einzelmolekülspektroskopie untersucht wird, wurde eine Perylendiimid-Terrylediimid Diade hergestellt. Die geringere Photostabilität des Donors ermöglichte zeitaufgelöste Einzelmolekül-messungen der Akzeptoremission mit und ohne Energietransfer vom Donor auf den Akzeptor. Durch diese Messungen konnten die Zeitkonstanten des Energietransfers für einzelne Diaden ermittelt werden. Ein weiterer Chromophor aus diesem Donor-Akzeptor-Paar soll die Möglichkeit eröffnen, den Energiefluß im Molekül gezielt zu manipulieren. Dazu wurde ein Donorchromophor mit zwei Akzeptoren in einem Multichromophor kombiniert. Im Rahmen der Synthesen dieser Arbeit wurden Terrylendiimide hergestellt, die in einer Imidstruktur eine Halogenfunktion trugen. Diese waren wichtige Synthesebausteine zum Aufbau von komplexen Chromophorarchitekturen. Ziel eines weiteren Kapitels war es, ein Terrylendiimid herzustellen, das als Sensibilisatorfarbstoff gemeinsam mit dem Haupt-Antennenkomplex von höheren Pflanzen LHCII in einer photoelektrochemischen Farbstoff-Solarzelle integriert werden konnte. Das hergestellte Terrylendiimid mit Carbonsäuregruppe eignete sich für Farbstoffsolarzellen auf Zinndioxidbasis.