Development of an innovative non rule-based energy management strategy for a Hybrid Electric Vehicle, structured for predictive driving controls based on external information knowledge

Recently, the interest of the automotive market for hybrid vehicles has increased due to the more restrictive pollutants emissions legislation and to the necessity of decreasing the fossil fuel consumption, since such solution allows a consistent improvement of the vehicle global efficiency. The term hybridization regards the energy flow in the powertrain of a vehicle: a standard vehicle has, usually, only one energy source and one energy tank; instead, a hybrid vehicle has at least two energy sources. In most cases, the prime mover is an internal combustion engine (ICE) while the auxiliary energy source can be mechanical, electrical, pneumatic or hydraulic. It is expected from the control unit of a hybrid vehicle the use of the ICE in high efficiency working zones and to shut it down when it is more convenient, while using the EMG at partial loads and as a fast torque response during transients. However, the battery state of charge may represent a limitation for such a strategy. That’s the reason why, in most cases, energy management strategies are based on the State Of Charge, or SOC, control. Several studies have been conducted on this topic and many different approaches have been illustrated. The purpose of this dissertation is to develop an online (usable on-board) control strategy in which the operating modes are defined using an instantaneous optimization method that minimizes the equivalent fuel consumption of a hybrid electric vehicle. The equivalent fuel consumption is calculated by taking into account the total energy used by the hybrid powertrain during the propulsion phases. The first section presents the hybrid vehicles characteristics. The second chapter describes the global model, with a particular focus on the energy management strategies usable for the supervisory control of such a powertrain. The third chapter shows the performance of the implemented controller on a NEDC cycle compared with the one obtained with the original control strategy.

Design of alternative energy storage systems for hybrid vehicles based on statistical processing of driving cycles information

Hybrid vehicles represent the future for automakers, since they allow to improve the fuel economy and to reduce the pollutant emissions. A key component of the hybrid powertrain is the Energy Storage System, that determines the ability of the vehicle to store and reuse energy. Though electrified Energy Storage Systems (ESS), based on batteries and ultracapacitors, are a proven technology, Alternative Energy Storage Systems (AESS), based on mechanical, hydraulic and pneumatic devices, are gaining interest because they give the possibility of realizing low-cost mild-hybrid vehicles. Currently, most literature of design methodologies focuses on electric ESS, which are not suitable for AESS design. In this contest, The Ohio State University has developed an Alternative Energy Storage System design methodology. This work focuses on the development of driving cycle analysis methodology that is a key component of Alternative Energy Storage System design procedure. The proposed methodology is based on a statistical approach to analyzing driving schedules that represent the vehicle typical use. Driving data are broken up into power events sequence, namely traction and braking events, and for each of them, energy-related and dynamic metrics are calculated. By means of a clustering process and statistical synthesis methods, statistically-relevant metrics are determined. These metrics define cycle representative braking events. By using these events as inputs for the Alternative Energy Storage System design methodology, different system designs are obtained. Each of them is characterized by attributes, namely system volume and weight. In the last part the work, the designs are evaluated in simulation by introducing and calculating a metric related to the energy conversion efficiency. Finally, the designs are compared accounting for attributes and efficiency values. In order to automate the driving data extraction and synthesis process, a specific script Matlab based has been developed. Results show that the driving cycle analysis methodology, based on the statistical approach, allows to extract and synthesize cycle representative data. The designs based on cycle statistically-relevant metrics are properly sized and have satisfying efficiency values with respect to the expectations. An exception is the design based on the cycle worst-case scenario, corresponding to same approach adopted by the conventional electric ESS design methodologies. In this case, a heavy system with poor efficiency is produced. The proposed new methodology seems to be a valid and consistent support for Alternative Energy Storage System design.

A numerical program for Railway vehicle-track-structure dynamic interaction using a modal substructuring approach

This work presents a program for simulations of vehicle-track and vehicle-trackstructure dynamic interaction . The method used is computationally efficient in the sense that a reduced number of coordinates is sufficient and doesn’t require high efficiency computers. The method proposes a modal substructuring approach of the system by modelling rails , sleepers and underlying structure with modal coordinates, the vehicle with physical lumped elements coordinates and by introducing interconnection elements between these structures (wheel-rail contact, railpads and ballast) by means of their interaction forces. The Frequency response function (FRF) is also calculated for both cases of track over a structure (a bridge, a viaduct ...) and for the simple vehicle-track program; for each case the vehicle effect on the FRF is then analyzed through the comparison of the FRFs obtained introducing or not a simplified vehicle on the system.

Influence of particle size, density and concentration on bend erosive wear in pneumatic conveyors

Particle concentration is a principal factor that affects erosion rate of solid surfaces under particle impact, such as pipe bends in pneumatic conveyors; it is well known that a reduction in the specific erosion rate occurs under high particle concentrations, a phenomenon referred to as the “shielding effect”. The cause of shielding is believed to be increased likelihood of inter-particulate collisions, the high collision probability between incoming and rebounding particles reducing the frequency and the severity of particle impacts on the target surface. In this study, the effects of particle concentration on erosion of a mild steel bend surface have been investigated in detail using three different particulate materials on an industrial scale pneumatic conveying test rig. The materials were studied so that two had the same particle density but very different particle size, whereas two had very similar particle size but very different particle density. Experimental results confirm the shielding effect due to high particle concentration and show that the particle density has a far more significant influence than the particle size, on the magnitude of the shielding effect. A new method of correcting for change in erosivity of the particles in repeated handling, to take this factor out of the data, has been established, and appears to be successful. Moreover, a novel empirical model of the shielding effects has been used, in term of erosion resistance which appears to decrease linearly when the particle concentration decreases. With the model it is possible to find the specific erosion rate when the particle concentration tends to zero, and conversely predict how the specific erosion rate changes at finite values of particle concentration; this is critical to enable component life to be predicted from erosion tester results, as the variation of the shielding effect with concentration is different in these two scenarios. In addition a previously unreported phenomenon has been recorded, of a particulate material whose erosivity has steadily increased during repeated impacts.

Metodi euristici per il Vehicle Routing Problem

Il problema della consegna di prodotti da un deposito/impianto ai clienti mediante una flotta di automezzi è un problema centrale nella gestione di una catena di produzione e distribuzione (supply chain). Questo problema, noto in letteratura come Vehicle Routing Problem (VRP), nella sua versione più semplice consiste nel disegnare per ogni veicolo disponibile presso un dato deposito aziendale un viaggio (route) di consegna dei prodotti ai clienti, che tali prodotti richiedono, in modo tale che (i) la somma delle quantità richieste dai clienti assegnati ad ogni veicolo non superi la capacità del veicolo, (ii) ogni cliente sia servito una ed una sola volta, (iii) sia minima la somma dei costi dei viaggi effettuati dai veicoli. Il VRP è un problema trasversale ad una molteplicità di settori merceologici dove la distribuzione dei prodotti e/o servizi avviene mediante veicoli su gomma, quali ad esempio: distribuzione di generi alimentari, distribuzione di prodotti petroliferi, raccolta e distribuzione della posta, organizzazione del servizio scuolabus, pianificazione della manutenzione di impianti, raccolta rifiuti, etc. In questa tesi viene considerato il Multi-Trip VRP, in cui ogni veicolo può eseguire un sottoinsieme di percorsi, chiamato vehicle schedule (schedula del veicolo), soggetto a vincoli di durata massima. Nonostante la sua importanza pratica, il MTVRP ha ricevuto poca attenzione in letteratura: sono stati proposti diversi metodi euristici e un solo algoritmo esatto di risoluzione, presentato da Mingozzi, Roberti e Toth. In questa tesi viene presentato un metodo euristico in grado di risolvere istanze di MTVRP in presenza di vincoli reali, quali flotta di veicoli non omogenea e time windows. L’euristico si basa sul modello di Prins. Sono presentati inoltre due approcci di local search per migliorare la soluzione finale. I risultati computazionali evidenziano l’efficienza di tali approcci.

Experimental characterization and modelling of a servo-pneumatic system for a knee loading apparatus

The new knee test rig developed in University of Bologna used pneumatic cylinder as actuator system. Specific characterization and modelling about the pneumatic cylinder and the related devices are needed in better controlling the test rig. In this thesis, an experimental environment for the related device is set up with data acquisition system using Real-time Windows Target, Simulink, MatLab. Based on the experimental data, a fitted model for the pneumatic cylinder friction is found.

Autonomous Vehicle and Internet on Vehicles

In questa tesi mi occupo di spiegare come si comportano i veicoli autonomi per prendere tutte le decisioni e come i dati dei sensori di ogni auto vengono condivisi con la flotta di veicoli

Meccanismi di Gamification per interfacce human-vehicle

L’obiettivo principale di questa tesi è utilizzare le tecniche di gamification più importanti nella progettazione ed implementazione di un’interfaccia Human-Vehicle per creare un software che possa rendere la guida di un’automobile elettrica più efficace ed efficiente da parte del guidatore. Per lo sviluppo del software è stato svolto uno studio specifico sulla gamification, sulle interfacce Human-Vehicle e sulle macchine elettriche attualmente in produzione. Successivamente è stata svolta la fase di progettazione in cui sono stati creati dei mockup relativi all’interfaccia grafica ed è stato svolto un focus group. Infine è stato implementato il vero e proprio software di simulazione EcoGame ed è stato effettuato un test utenti.

Unmanned Aerial Vehicle (UAV) per applicazioni geomatiche

La tesi tratta i dispositivi UAV, in particolare i droni di peso inferiore ai 25 kg, facendo riferimento alla normativa ENAC. Vengono descritte le applicazioni pratiche in campo civile, concentrandosi sulle geomatiche, delineando i principali sensori esterni utilizzati come Camere digitali, termiche e multispettrali.