Performance comparison of C-V2X and WAVE protocols for vehicular to infrastructure communications: simulation of the highway use case

The objective of this thesis is the analysis and the study of the various access techniques for vehicular communications, in particular of the C-V2X and WAVE protocols. The simulator used to study the performance of the two protocols is called LTEV2Vsim and was developed by the CNI IEIIT for the study of V2V (Vehicle-to-Vehicle) communications. The changes I made allowed me to study the I2V (Infrastructure-to-Vehicle) scenario in highway areas and, with the results obtained, I made a comparison between the two protocols in the case of high vehicular density and low vehicular density, putting in relation to the PRR (packet reception ratio) and the cell size (RAW, awareness range). The final comparison allows to fully understand the possible performances of the two protocols and highlights the need for a protocol that allows to reach the minimum necessary requirements.

Analisi e valutazione delle performance acustiche degli aeromobili nella fase di atterraggio

Nella tesi si analizzano le principali fonti del rumore aeronautico, lo stato dell'arte dal punto di vista normativo, tecnologico e procedurale. Si analizza lo stato dell'arte anche riguardo alla classificazione degli aeromobili, proponendo un nuovo indice prestazionale in alternativa a quello indicato dalla metodologia di certificazione (AC36-ICAO) Allo scopo di diminuire l'impatto acustico degli aeromobili in fase di atterraggio, si analizzano col programma INM i benefici di procedure CDA a 3° rispetto alle procedure tradizionali e, di seguito di procedure CDA ad angoli maggiori in termini di riduzione di lunghezza e di area delle isofoniche SEL85, SEL80 e SEL75.

Ottimizzazione di un Sistema di Key Performance Indicators per la Divisione Engineering aziendale. Il caso INTERTABA S.p.A.

Il seguente elaborato è la diretta conseguenza di un periodo di stage, pari a cinque mesi, svolto presso l’azienda INTERTABA S.p.A., a Zola Predosa (BO). Il Dipartimento presso cui è stato svolto il tirocinio è l’Engineering. In particolare è stata compiuta un’analisi dei KPIs presenti e sono state proposte delle azioni migliorative. Il lavoro si è sviluppato in tre fasi. Nella prima fase è stata fatta un’analisi dei KPIs attuali per ciascuna funzione appartenente all’Engineering: Engineering Support, Project Engineering, Plant & Utilities Maintenance, Technical Warehouse e General Services. Nella seconda fase sono state descritte, per ciascuna funzione, alcune proposte migliorative per i KPIs presenti. Infine, per alcune funzioni, sono state proposte alcune iniziative in merito all’implementazione di nuovi KPIs.

Evaluation of the power production performance of the wavepiston, wave energy converter

In the early 1970 the community has started to realize that have as a main principle the industry one, with the oblivion of the people and health conditions and of the world in general, it could not be a guideline principle. The sea, as an energy source, has the characteristic of offering different types of exploitation, in this project the focus is on the wave energy. Over the last 15 years the Countries interested in the renewable energies grew. Therefore many devices have came out, first in the world of research, then in the commercial one; these converters are able to achieve an energy transformation into electrical energy. The purpose of this work is to analyze the efficiency of a new wave energy converter, called WavePiston, with the aim of determine the feasibility of its actual application in different wave conditions: from the energy sea state of the North Sea, to the more quiet of the Mediterranean Sea. The evaluation of the WavePiston is based on the experimental investigation conducted at the University of Aalborg, in Denmark; and on a numerical modelling of the device in question, to ascertain its efficiency regardless the laboratory results. The numerical model is able to predict the laboratory condition, but it is not yet a model which can be used for any installation, in fact no mooring or economical aspect are included yet. È dai primi anni del 1970 che si è iniziato a capire che il solo principio dell’industria con l’incuranza delle condizioni salutari delle persone e del mondo in generale non poteva essere un principio guida. Il mare, come fonte energetica, ha la caratteristica di offrire diverse tipologie di sfruttamento, in questo progetto è stata analizzata l’energia da onda. Negli ultimi 15 anni sono stati sempre più in aumento i Paesi interessati in questo ambito e di conseguenza, si sono affacciati, prima nel mondo della ricerca, poi in quello commerciale, sempre più dispositivi atti a realizzare questa trasformazione energetica. Di tali convertitori di energia ondosa ne esistono diverse classificazioni. Scopo di tale lavoro è analizzare l’efficienza di un nuovo convertitore di energia ondosa, chiamato WavePiston, al fine si stabilire la fattibilità di una sua reale applicazione in diverse condizioni ondose: dalle più energetiche del Mare del Nord, alle più quiete del Mar Mediterraneo. La valutazione sul WavePiston è basata sullo studio sperimentale condotto nell’Università di Aalborg, in Danimarca; e su di una modellazione numerica del dispositivo stesso, al fine di conoscerne l’efficienza a prescindere dalla possibilità di avere risultati di laboratorio. Il modello numerico è in grado di predirre le condizioni di laboratorio, ma non considera ancora elementi come gli ancoraggi o valutazione dei costi.

Frost heave testing of norwegian materials for road infrastructure

In areas of seasonal frost, frost susceptibility composed by frost heaving during the winter and thaw softening during the spring is one of the most dangerous phenomenon for transportation, road and railway infrastructure. Therefore, the need for frost protection layer becomes imperative. The purpose of frost protection layer is to prevent frost from penetrating down through the pavement and into the sub-soils. Frost susceptible soils under the road can be cause damages on the roads or other structures due to frost heave or reduced capacity characteristics thaw period. "Frost heave" is the term given to the upwards displacement of the ground surface caused by the formation of ice within soils or aggregates (Rempel et al., 2004). Nowadays in Scandinavia the most common material used in frost protection layer in the pavement structure of roads and in the ballast of the railway tracks are coarse-grain crushed rocks aggregates. Based on the capillary rise, the mechanics of frost heave phenomenon is based on the interaction between aggregates and water, as suggested by Konrad and Lemieux in 2005 that said that the fraction of material below the 0.063 mm sieve for coarse-grained soils must be controlled so as to reduce the sensitivity to frost heave. The study conducted in this thesis project is divided in two parts: - the analysis of the coarse grained aggregates used in frost protection layer in Norway; - the analysis of the frost heave phenomenon in the laboratory under known boundary conditions, through the use of the most widely used method, the frost heave test, in” closed system” (without access of water).

Design and Implementation of a Cloud Infrastructure for Distributed Scientific Calculation

Cloud computing enables independent end users and applications to share data and pooled resources, possibly located in geographically distributed Data Centers, in a fully transparent way. This need is particularly felt by scientific applications to exploit distributed resources in efficient and scalable way for the processing of big amount of data. This paper proposes an open so- lution to deploy a Platform as a service (PaaS) over a set of multi- site data centers by applying open source virtualization tools to facilitate operation among virtual machines while optimizing the usage of distributed resources. An experimental testbed is set up in Openstack environment to obtain evaluations with different types of TCP sample connections to demonstrate the functionality of the proposed solution and to obtain throughput measurements in relation to relevant design parameters.

From F energy rating to Nearly ZEB: project of energy retrofit and architectural upgrade of a brick terraced house in Co. Dublin, Ireland

Questo progetto è stato sviluppato durante un periodo di ricerca presso il Dipartimento di Ingegneria Civile del Trinity College e continuato presso l’Università di Bologna. Il progetto ha l’obiettivo di analizzare le soluzioni per l’ampliamento, la sostituzione degli impianti e l’ottimizzazione energetica di un tipico edificio residenziale Irlandese, una end of terrace in mattoni costruita negli anni ’20, collocata a Blackrock (Dublino). Diversi studi sostengono che lo stock abitativo irlandese è il peggiore del nord Europa per quanto riguarda la performance energetica. Questa tesi consta di una prima parte di studio del contesto e delle tecniche costruttive tradizionali irlandesi; è presente un capitolo di approfondimento sulle leggi riguardanti le costruzioni e gli incentivi forniti dal governo irlandese per interventi di retrofit energetico. Il terzo capitolo è un’analisi dell'esistente, con disegni del rilievo geometrico, immagini dell’edificio originale, termogrammi e dati riguardanti l’attuale performance energetica. Vengono poi mostrate diverse ipotesi di progetto e, una volta determinata la disposizione degli spazi interni, vengono considerate due soluzioni simili, ma costruite con pacchetti costruttivi diversi. Nel Progetto A l’involucro dell’addizione ha una struttura in muratura, nel Progetto B la struttura è in X-lam. Le performance energetiche delle due proposte vengono confrontate tramite una simulazione attuata grazie all'utilizzo del software dinamico IES-VE. Viene valutata l’applicazione di energie rinnovabili, quali l’energia solare e eolica e l’apporto che queste possono dare al bilancio energetico. Infine viene fatta un’analisi dei costi, valutando possibili suddivisioni dei lavori e ipotizzando un piano di ritorno dell’investimento, anche in combinazione con l’applicazione di energie rinnovabili. Alla fine del progetto si trova una valutazione quantitativa dei miglioramenti dell’edificio e un’analisi critica dei limiti del progetto.

Wind analysis of the Messina Strait Bridge design project proposal with stabilizing cables

A new study on suspension bridges has been prompted by the big disaster of the Tacoma Narrow Bridge at half its design speed. The aerodynamic instability of long-span bridges has been studied using wind tunnel tests. As a result of improved aerodynamic performance from the geometrical configuration of the bridge deck, the aerodynamic criteria for suspension and cable-stayed bridges have become well established in recent years, thereby allowing longer bridge spans to be developed. Although the Messina Strait Bridge has yet to be constructed, we are looking forward to evaluating the impact of different deck cross-sections on both aerodynamic stability and cost reduction. To further improve the aerodynamic characteristics of long-span suspension bridges, an optimized multi-box bridge deck model with two side decks for traffic lanes, two middle railway decks, and three gaps separating them has been proposed aerodynamic performance has been experimentally verified. 1:80 scale wind tunnel tests have been conducted. According to the current MIDAS Model, the first torsional and the first vertical frequency ratios are 1.27787 and 1.36[1] respectively. It is the torsional/vertical frequency ratio, combined with the deck aerodynamic properties, that determines the wind response properties of the bridge for the most dangerous possible form of aeroelastic instability. The classic flutter is caused by the coupling of torsional and vertical modes. Stabilizing cables to the deck could be a solution to this classic flutter by reducing lateral displacement of the deck and increasing frequency ratios. Stabilizing cables will be installed on the deck in three different orientations: vertical, inclined, and horizontal, with diameters of 80 cm, 60 cm, and 40 cm in each orientation respectively. An overview of the research undertaken on this topic will be presented, as well as the most important findings.

Machine learning "as a service" for high energy physics (MLaaS4HEP): evolution of a framework for ML-based physics analyses

The scientific success of the LHC experiments at CERN highly depends on the availability of computing resources which efficiently store, process, and analyse the amount of data collected every year. This is ensured by the Worldwide LHC Computing Grid infrastructure that connect computing centres distributed all over the world with high performance network. LHC has an ambitious experimental program for the coming years, which includes large investments and improvements both for the hardware of the detectors and for the software and computing systems, in order to deal with the huge increase in the event rate expected from the High Luminosity LHC (HL-LHC) phase and consequently with the huge amount of data that will be produced. Since few years the role of Artificial Intelligence has become relevant in the High Energy Physics (HEP) world. Machine Learning (ML) and Deep Learning algorithms have been successfully used in many areas of HEP, like online and offline reconstruction programs, detector simulation, object reconstruction, identification, Monte Carlo generation, and surely they will be crucial in the HL-LHC phase. This thesis aims at contributing to a CMS R&D project, regarding a ML "as a Service" solution for HEP needs (MLaaS4HEP). It consists in a data-service able to perform an entire ML pipeline (in terms of reading data, processing data, training ML models, serving predictions) in a completely model-agnostic fashion, directly using ROOT files of arbitrary size from local or distributed data sources. This framework has been updated adding new features in the data preprocessing phase, allowing more flexibility to the user. Since the MLaaS4HEP framework is experiment agnostic, the ATLAS Higgs Boson ML challenge has been chosen as physics use case, with the aim to test MLaaS4HEP and the contribution done with this work.

Satellite IoT: a Study and Performance Analysis of GEO and LEO Systems

The study is divided into two main part: one focused on the GEO Satellite IoT and the other on the LEO Satellite IoT. Concerning the GEO Satellite IoT, the activity has been developed in the context of EUMETSAT Data Collection Service (DCS) by investigating the performance at the receiver within challenging scenarios. DCS are provided by several GEO Satellite operators, giving almost total coverage around the world. In this study firstly an overview of the DCS end-to-end architecture is given followed by a detailed description of both the tools used for the simulations: the DCP-TST (message generator and transmitter) and the DCP-RX (receiver). After generating several test messages, the performances have been evaluated with the addition of impairments (CW and sweeping interferences) and considerations in terms of BER and Good Messages are produced. Furthermore, a study on the PLL System is also conducted together with evaluations on the effectiveness of tuning the PLL Bw on the overall performance. Concerning the LEO Satellite IoT, the activity was carried out in the framework of the ASI Bidirectional IoT Satellite Service (BISS) Project. The elaborate covers a survey about the possible services that the project can accomplish and a technical analysis on the uplink MA. In particular, the LR-FHSS is proved to be a valid alternative for the uplink through an extensive analysis on its Network capacity and through the study of an analytic model for Success Probability with its Matlab implementation.

Deployment of a data analysis workflow of the ATLAS experiment on HPC systems

LHC experiments produce an enormous amount of data, estimated of the order of a few PetaBytes per year. Data management takes place using the Worldwide LHC Computing Grid (WLCG) grid infrastructure, both for storage and processing operations. However, in recent years, many more resources are available on High Performance Computing (HPC) farms, which generally have many computing nodes with a high number of processors. Large collaborations are working to use these resources in the most efficient way, compatibly with the constraints imposed by computing models (data distributed on the Grid, authentication, software dependencies, etc.). The aim of this thesis project is to develop a software framework that allows users to process a typical data analysis workflow of the ATLAS experiment on HPC systems. The developed analysis framework shall be deployed on the computing resources of the Open Physics Hub project and on the CINECA Marconi100 cluster, in view of the switch-on of the Leonardo supercomputer, foreseen in 2023.