A numerical study of temperature effects on hot wire measurements inside turbulent channel flows

A way to investigate turbulence is through experiments where hot wire measurements are performed. Analysis of the in turbulence of a temperature gradient on hot wire measurements is the aim of this thesis work. Actually - to author's knowledge - this investigation is the first attempt to document, understand and ultimately correct the effect of temperature gradients on turbulence statistics. However a numerical approach is used since instantaneous temperature and streamwise velocity fields are required to evaluate this effect. A channel flow simulation at Re_tau = 180 is analyzed to make a first evaluation of the amount of error introduced by temperature gradient inside the domain. Hot wire data field is obtained processing the numerical flow field through the application of a proper version of the King's law, which connect voltage, velocity and temperature. A drift in mean streamwise velocity profile and rms is observed when temperature correction is performed by means of centerline temperature. A correct mean velocity pro�le is achieved correcting temperature through its mean value at each wall normal position, but a not negligible error is still present into rms. The key point to correct properly the sensed velocity from the hot wire is the knowledge of the instantaneous temperature field. For this purpose three correction methods are proposed. At the end a numerical simulation at Re_tau =590 is also evaluated in order to confirm the results discussed earlier.

Numerical investigation of turbulent/non-turbulent interface

The subject of this work is the diffusion of turbulence in a non-turbulent flow. Such phenomenon can be found in almost every practical case of turbulent flow: all types of shear flows (wakes, jet, boundary layers) present some boundary between turbulence and the non-turbulent surround; all transients from a laminar flow to turbulence must account for turbulent diffusion; mixing of flows often involve the injection of a turbulent solution in a non-turbulent fluid. The mechanism of what Phillips defined as “the erosion by turbulence of the underlying non-turbulent flow”, is called entrainment. It is usually considered to operate on two scales with different mechanics. The small scale nibbling, which is the entrainment of fluid by viscous diffusion of turbulence, and the large scale engulfment, which entraps large volume of flow to be “digested” subsequently by viscous diffusion. The exact role of each of them in the overall entrainment rate is still not well understood, as it is the interplay between these two mechanics of diffusion. It is anyway accepted that the entrainment rate scales with large properties of the flow, while is not understood how the large scale inertial behavior can affect an intrinsically viscous phenomenon as diffusion of vorticity. In the present work we will address then the problem of turbulent diffusion through pseudo-spectral DNS simulations of the interface between a volume of decaying turbulence and quiescent flow. Such simulations will give us first hand measures of velocity, vorticity and strains fields at the interface; moreover the framework of unforced decaying turbulence will permit to study both spatial and temporal evolution of such fields. The analysis will evidence that for this kind of flows the overall production of enstrophy , i.e. the square of vorticity omega^2 , is dominated near the interface by the local inertial transport of “fresh vorticity” coming from the turbulent flow. Viscous diffusion instead plays a major role in enstrophy production in the outbound of the interface, where the nibbling process is dominant. The data from our simulation seems to confirm the theory of an inertially stirred viscous phenomenon proposed by others authors before and provides new data about the inertial diffusion of turbulence across the interface.

Numerical simulation of interdigitated back contact hetero-junction solar cells

The goal of this thesis is the application of an opto-electronic numerical simulation to heterojunction silicon solar cells featuring an all back contact architecture (Interdigitated Back Contact Hetero-Junction IBC-HJ). The studied structure exhibits both metal contacts, emitter and base, at the back surface of the cell with the objective to reduce the optical losses due to the shadowing by front contact of conventional photovoltaic devices. Overall, IBC-HJ are promising low-cost alternatives to monocrystalline wafer-based solar cells featuring front and back contact schemes, in fact, for IBC-HJ the high concentration doping diffusions are replaced by low-temperature deposition processes of thin amorphous silicon layers. Furthermore, another advantage of IBC solar cells with reference to conventional architectures is the possibility to enable a low-cost assembling of photovoltaic modules, being all contacts on the same side. A preliminary extensive literature survey has been helpful to highlight the specific critical aspects of IBC-HJ solar cells as well as the state-of-the-art of their modeling, processing and performance of practical devices. In order to perform the analysis of IBC-HJ devices, a two-dimensional (2-D) numerical simulation flow has been set up. A commercial device simulator based on finite-difference method to solve numerically the whole set of equations governing the electrical transport in semiconductor materials (Sentuarus Device by Synopsys) has been adopted. The first activity carried out during this work has been the definition of a 2-D geometry corresponding to the simulation domain and the specification of the electrical and optical properties of materials. In order to calculate the main figures of merit of the investigated solar cells, the spatially resolved photon absorption rate map has been calculated by means of an optical simulator. Optical simulations have been performed by using two different methods depending upon the geometrical features of the front interface of the solar cell: the transfer matrix method (TMM) and the raytracing (RT). The first method allows to model light prop-agation by plane waves within one-dimensional spatial domains under the assumption of devices exhibiting stacks of parallel layers with planar interfaces. In addition, TMM is suitable for the simulation of thin multi-layer anti reflection coating layers for the reduction of the amount of reflected light at the front interface. Raytracing is required for three-dimensional optical simulations of upright pyramidal textured surfaces which are widely adopted to significantly reduce the reflection at the front surface. The optical generation profiles are interpolated onto the electrical grid adopted by the device simulator which solves the carriers transport equations coupled with Poisson and continuity equations in a self-consistent way. The main figures of merit are calculated by means of a postprocessing of the output data from device simulation. After the validation of the simulation methodology by means of comparison of the simulation result with literature data, the ultimate efficiency of the IBC-HJ architecture has been calculated. By accounting for all optical losses, IBC-HJ solar cells result in a theoretical maximum efficiency above 23.5% (without texturing at front interface) higher than that of both standard homojunction crystalline silicon (Homogeneous Emitter HE) and front contact heterojuction (Heterojunction with Intrinsic Thin layer HIT) solar cells. However it is clear that the criticalities of this structure are mainly due to the defects density and to the poor carriers transport mobility in the amorphous silicon layers. Lastly, the influence of the most critical geometrical and physical parameters on the main figures of merit have been investigated by applying the numerical simulation tool set-up during the first part of the present thesis. Simulations have highlighted that carrier mobility and defects level in amorphous silicon may lead to a potentially significant reduction of the conversion efficiency.

Regularity of solutions of the p-Laplace equation in the Heisenberg group

tbd

Dispersive wave solutions of the klein-gordon equation in cosmology

L'equazione di Klein-Gordon descrive una ampia varietà di fenomeni fisici come la propagazione delle onde in Meccanica dei Continui ed il comportamento delle particelle spinless in Meccanica Quantistica Relativistica. Recentemente, la forma dissipativa di questa equazione si è rivelata essere una legge di evoluzione fondamentale in alcuni modelli cosmologici, in particolare nell'ambito dei cosiddetti modelli di k-inflazione in presenza di campi tachionici. L'obiettivo di questo lavoro consiste nell'analizzare gli effetti del parametro dissipativo sulla dispersione nelle soluzioni dell'equazione d'onda. Saranno inoltre studiati alcuni tipici problemi al contorno di particolare interesse cosmologico per mezzo di grafici corrispondenti alle soluzioni fondamentali (Funzioni di Green).

A numerical study of turbulent Rayleigh-Bénard convection

Il flusso di Rayleigh-Bénard, costituito da un fluido racchiuso fra due pareti a diversa temperatura, rappresenta il paradigma della convezione termica. In natura e nelle applicazioni industriali, il moto convettivo avviene principalmente in regime turbolento, rivelando un fenomeno estremamente complesso. L'obiettivo principale di questo elaborato di tesi consiste nell'isolare e descrivere gli aspetti salienti di un flusso turbolento di Rayleigh-Bénard. L'analisi è applicata a dati ottenuti da tre simulazioni numeriche dirette effettuate allo stesso numero di Rayleigh (Ra=10^5) e a numeri di Prandtl differenti (Pr=0.7,2,7). Sulla base di alcune statistiche a singolo punto, vengono definite nel flusso tre regioni caratteritiche: il bulk al centro della cella, lo strato limite termico e quello viscoso in prossimità delle pareti. Grazie all'analisi dei campi istantanei e delle correlazioni spaziali a due punti, sono state poi individuate due strutture fondamentali della convezione turbolenta: le piume termiche e la circolazione a grande scala. L'equazione generalizzata di Kolmogorov, introdotta nell'ultima parte della trattazione, permette di approcciare il problema nella sua complessità, visualizzando come l'energia cinetica viene immessa, si distribuisce e viene dissipata sia nello spazio fisico, sia in quello delle scale turbolente. L'immagine che emerge dall'analisi complessiva è quella di un flusso del tutto simile a una macchina termica. L'energia cinetica viene prodotta nel bulk, considerato il motore del flusso, e da qui fluisce verso le pareti, dove viene infine dissipata.

"Offshore tower or platform foundations: numerical analysis of a laterally loaded single pile or pile group in soft clay and analysis of actions on a jacket structure"

Laterally loaded piles are a typical situation for a large number of cases in which deep foundations are used. Dissertation herein reported, is a focus upon the numerical simulation of laterally loaded piles. In the first chapter the best model settings are largely discussed, so a clear idea about the effects of interface adoption, model dimension, refinement cluster and mesh coarseness is reached. At a second stage, there are three distinct parametric analyses, in which the model response sensibility is studied for variation of interface reduction factor, Eps50 and tensile cut-off. In addition, the adoption of an advanced soil model is analysed (NGI-ADP). This was done in order to use the complex behaviour (different undrained shear strengths are involved) that governs the resisting process of clay under short time static loads. Once set a definitive model, a series of analyses has been carried out with the objective of defining the resistance-deflection (P-y) curves for Plaxis3D (2013) data. Major results of a large number of comparisons made with curves from API (America Petroleum Institute) recommendation are that the empirical curves have almost the same ultimate resistance but a bigger initial stiffness. In the second part of the thesis a simplified structural preliminary design of a jacket structure has been carried out to evaluate the environmental forces that act on it and on its piles foundation. Finally, pile lateral response is studied using the empirical curves.

Preconditioning strategies for the numerical solution of convection-diffusion partial differential equations

Il trattamento numerico dell'equazione di convezione-diffusione con le relative condizioni al bordo, comporta la risoluzione di sistemi lineari algebrici di grandi dimensioni in cui la matrice dei coefficienti è non simmetrica. Risolutori iterativi basati sul sottospazio di Krylov sono ampiamente utilizzati per questi sistemi lineari la cui risoluzione risulta particolarmente impegnativa nel caso di convezione dominante. In questa tesi vengono analizzate alcune strategie di precondizionamento, atte ad accelerare la convergenza di questi metodi iterativi. Vengono confrontati sperimentalmente precondizionatori molto noti come ILU e iterazioni di tipo inner-outer flessibile. Nel caso in cui i coefficienti del termine di convezione siano a variabili separabili, proponiamo una nuova strategia di precondizionamento basata sull'approssimazione, mediante equazione matriciale, dell'operatore differenziale di convezione-diffusione. L'azione di questo nuovo precondizionatore sfrutta in modo opportuno recenti risolutori efficienti per equazioni matriciali lineari. Vengono riportati numerosi esperimenti numerici per studiare la dipendenza della performance dei diversi risolutori dalla scelta del termine di convezione, e dai parametri di discretizzazione.

Numerical evaluation of material model and thickness effect on LSP induced residual stresses

Laser Shock Peening (LSP) is a technological process used to improve mechanical properties in metallic components. When a short and intense laser pulse irradiates a metallic surface, high pressure plasma is generated on the treated surface; elasto-plastic waves, then, propagate inside the target and create plastic strain. This surface treatment induces a deep compressive residual stresses field on the treated area and through the thickness; such compressive residual stress is expected to increase the fatigue resistance, and reduce the detrimental effects of corrosion and stress corrosion cracking.

Analysis and partial solutions of security problems in automotive environments

Questo scritto mira a fare una panoramica dei problemi legati alla sicurezza della comunicazione tra componenti interne dei veicoli e delle soluzioni oggigiorno disponibili. Partendo con una descrizione generale del circuito interno dell’auto analizzeremo i suoi punti di accesso e discuteremo i danni prodotti dalla sua manomissione illecita. In seguito vedremo se ´è possibile prevenire tali attacchi dando un’occhiata alle soluzioni disponibili e soffermandoci in particolare sui moduli crittografici e le loro applicazioni. Infine presenteremo l’implementazione pratica di un protocollo di autenticazione tra ECUs e una dimostrazione matematica della sua sicurezza.

Numerical simulations of the effects of residual stresses in adhesively bonded composite specimen

In this work the problem of performing a numerical simulation of quasi-static crack propagation within an adhesive layer of a bonded joint under Mode I loading affected by stress field changes due to thermal-chemical shrinkage induced by cure process is addressed. Secondly, a parametric study on fracture critical energy, cohesive strength and Young's modulus is performed. Finally, a particular case of adhesive layer stiffening is simulated in order to verify qualitatively the major effect.

Physical characterization and numerical modeling of a WEST-like tokamak divertor plasma

Il presente elaborato è incentrato sulla modellizzazione del plasma di bordo nei dispositivi per la produzione di energia da fusione nucleare noti come tokamak. La tecnologia che nel corso di tutta la seconda metà del XX secolo fino ad oggi è stata sviluppata a questo fine deve necessariamente scontrarsi con alcuni limiti. Nei tokamak il confinamento del plasma è di tipo magnetico e vincola le particelle a muoversi di moto elicoidale all'interno del vessel, tuttavia il confinamento non risulta perfetto e parte dell'energia si scarica sulle pareti della camera, rischiando pertanto di fondere i materiali. Alcune strategie possono essere messe in atto per limitare questo problema, per esempio agendo sulla geometria del tokamak, oppure sulla fisica, inducendo nel plasma una data concentrazione di impurezze che ionizzino irraggiando parte dell'energia di plasma. Proprio tale meccanismo di perdita è stato simulato in un modello monodimensionale di plasma monofluido di bordo. I risultati del codice numerico relativo al modello dimostrano che per concentrazioni di impurezze crescenti è possibile diminuire in modo significativo flusso di calore e temperatura al divertore. Per di più risulta possibile controllare la posizione del fronte di irraggiamento per mezzo di parametri di controllo del plasma quali la pressione. Si osserva inoltre l'insorgere del cosiddetto fenomeno di biforcazione alle basse temperature di divertore, fenomeno in cui il plasma si comporta in modo instabile a causa di fenomeni fisici tipici delle basse energie ("detachment") e a seguito del quale può improvvisamente spegnersi (disruzione). Infine lo stesso modello è stato migliorato inserendo l'ipotesi di plasma bifluido. Anche per gli ioni viene osservato il fenomeno di biforcazione. I risultati numerici evidenziano le dinamiche dello scambio energetico fra le specie gettando le basi di una progettazione efficiente della chimica del plasma finalizzata al raffreddamento del divertore.

Advanced numerical modeling of masonry vaulted structures based on BIM parametric geometry generation

Vaults are an architectural element which during construction history have been built with a great variety of different materials, shapes, and sizes. The shape of these structural elements was often dependent by the necessity to cover complex spaces, by the needed loading capacity, or by architectural aesthetics. Within this complex scenario masonry patterns generates also different effects on loading capacity, load percolation and stiffness of the structure. These effects were been extensively investigated, both with empirical observations and with modern numerical methods. While most of them focus on analyzing the load bearing capacity or the texture effect on vaulted structures, the aim of this analysis is to investigate on the effects of the variation of a single structural characteristic on the load percolation in the vault. Moreover, an additional purpose of the work is related to the coding of a parametrical model aiming at generating different masonry vaulted structures. Nevertheless, proposed script can generate different typology of vaulted structure basing on some structural characteristics, such as the span and the length to cover and the dimensions of the blocks.

Numerical modelling of hydrodinamics and morphodynamics for the Friuli Venezia Giulia coast

Integrated Coastal Zone Management (ICZM) should be considered as one of the main components to be able to implement sustainable development. Friuli Venezia Giulia region with its 93 km of coastline is committed to investing its resources in projects aimed at studying the evolution of the coast. In this report, reference will be made to the area in front of the municipality of Grado, where the Banco della Mula di Muggia is located. Starting from previous studies and surveys, morphology of the coastal stretch between the municipality of Grado and the mouth of the Isonzo river will be reproduced through numerical modeling tools, to simulate its hydrodynamic behavior on an annual basis and also as a function of significant events such as storms, calm events or floods of the Isonzo river. The software employed will be the MIKE by DHI with in particular the implementation of "Littoral Drift" and "MIKE 21/3" Coupled models. The first to calculate net and gross longshore transport on an annual basis along a transverse profile, the latter is a modelling system for coastal application that will be used for the analysis of significant events effects. Although not primary focus of this work, there will be included an initial review of finger bars. These particular sand formations are present at the south-western border of the Banco della Mula di Muggia and may have an impact on it. This work could form the starting point of future investigations to build on the findings of this report.

Numerical modelling of axially loaded piled foundations with physical tests validation

L'oggetto della tesi è la modellazione numerica di pali di fondazione per turbine eoliche in ambiente offshore. Il metodo di modellazione comprende l'interpretazione di prove CPT per l'estrapolazione dei parametri geotecnici del terreno, la creazione di un modello dell'interazione tra struttura e terreno tramite il software agli elementi finiti Abaqus, la sua verifica, l'ottimizzazione dell'estensione del modello del terreno e della mesh e la simulazione numerica del comportamento di pali caricati assialmente in compressione. Grazie al confronto con i risultati di test su modelli fisici, eseguiti nel laboratorio dell'istituto Fraunhofer IWES di Hannover, di tre pali aventi la stessa geometria ma installati in punti con diverse condizioni di compattazione della sabbia, è stata possibile la messa a punto di una strategia di simulazione più accurata possibile e la sua validazione. A conclusione del lavoro è stato eseguito un esempio di design di una fondazione jacket per una turbina eolica offshore.