Structural steel design with BIM technology - interventions on a three buildings block in Deruta (PG)

The aim of this thesis is to use the developments, advantages and applications of "Building Information Modelling" (BIM) with emphasis on the discipline of structural design for steel building located in Perugia. BIM was mainly considered as a new way of planning, constructing and operating buildings or infrastructures. It has been found to offer greater opportunities for increased efficiency, optimization of resources and generally better management throughout the life cycle of a facility. BIM increases the digitalization of processes and offers integrated and collaborative technologies for design, construction and operation. To understand BIM and its benefits, one must consider all phases of a project. Higher initial design costs often lead to lower construction and operation costs. Creating data-rich digital models helps to better predict and coordinate the construction phases and operation of a building. One of the main limitations identified in the implementation of BIM is the lack of knowledge and qualified professionals. Certain disciplines such as structural and mechanical design depend on whether the main contractor, owner, general contractor or architect need to use or apply BIM to their projects. The existence of a supporting or mandatory BIM guideline may then eventually lead to its adoption. To test the potential of the BIM adoption in the steel design process, some models were developed taking advantage of a largely diffuse authoring software (Autodesk Revit), to produce construction drawings and also material schedule that were needed in order to estimate quantities and features of a real steel building. Once the model has been built the whole process has been analyzed and then compared with the traditional design process of steel structure. Many relevant aspect in term of clearness and also in time spent were shown and lead to final conclusions about the benefits from BIM methodology.

Design and development of the new composite-material mainplane of the Dallara T12 race car

Abstract (US) Composite material components design and production techniques are discussed in the present graduation paper. In particular, this paper covers the design process and the production process of a carbon-fiber composite material component for a high performance car, more specifically, the Dallara T12 race car. This graduation paper is split in two. After a brief introduction on existing composite materials (their origins and applications), the first part of the present paper covers the main theoretical concepts behind the design of composite material components: particular focus will be given to carbon-fiber composites. The second part of the present paper covers the whole design and production process that the candidate carried out to create the new front mainplane of the Dallara T12 race car. This graduation paper is the result of a six-months-long internship that the candidate conducted as Design Office Trainee inside Dallara Automobili S.p.A. Abstract (ITA) La presente tesi di laurea discute le metodologie progettuali e produttive legate alla realizzazione di un componente in materiale composito. Nello specifico, viene discussa la progettazione e la produzione di un componente in fibra di carbonio destinato ad una vettura da competizione. La vettura in esame è la Dallara T12. Il lavoro è diviso in due parti. Nella prima parte, dopo una breve introduzione sull’origine e le tipologie di materiali compositi esistenti, vengono trattati i concetti teorici fondamentali su cui si basa la progettazione di generici componenti in materiale composito, con particolare riguardo ai materiali in fibra di carbonio. Nella seconda parte viene discusso tutto il processo produttivo che il candidato ha portato a termine per realizzare il nuovo alettone anteriore della Dallara T12. La presente tesi di laurea è il risultato del lavoro di progettazione che il candidato ha svolto presso l’Ufficio Tecnico di Dallara Automobili S.p.A. nel corso di un tirocinio formativo di sei mesi.

La strategia BIM a supporto del progetto della sicurezza nel cantiere edile: il caso dell'ospedale di primo soccorso a Lampedusa.

Throughout this research, the whole life cycle of a building will be analyzed, with a special focus on the most common issues that affect the construction sector nowadays, such as safety. In fact, the goal is to enhance the management of the entire construction process in order to reduce the risk of accidents. The contemporary trend is that of researching new tools capable of reducing, or even eliminating, the most common mistakes that usually lead to safety risks. That is one of the main reasons why new technologies and tools have been introduced in the field. The one we will focus on is the so-called BIM: Building Information Modeling. With the term BIM we refer to wider and more complex analysis tool than a simple 3D modeling software. Through BIM technologies we are able to generate a multi-dimension 3D model which contains all the information about the project. This innovative approach aims at a better understanding and control of the project by taking into consideration the entire life cycle and resulting in a faster and more sustainable way of management. Furthermore, BIM software allows for the sharing of all the information among the different aspects of the project and among the different participants involved thus improving the cooperation and communication. In addition, BIM software utilizes smart tools that simulate and visualize the process in advance, thus preventing issues that might not have been taking into consideration during the design process. This leads to higher chances of avoiding risks, delays and cost increases. Using a hospital case study, we will apply this approach for the completion of a safety plan, with a special focus onto the construction phase.

Design methods and geometric modelling of scaffolds for bone tissue engineering

Every year, thousand of surgical treatments are performed in order to fix up or completely substitute, where possible, organs or tissues affected by degenerative diseases. Patients with these kind of illnesses stay long times waiting for a donor that could replace, in a short time, the damaged organ or the tissue. The lack of biological alternates, related to conventional surgical treatments as autografts, allografts, e xenografts, led the researchers belonging to different areas to collaborate to find out innovative solutions. This research brought to a new discipline able to merge molecular biology, biomaterial, engineering, biomechanics and, recently, design and architecture knowledges. This discipline is named Tissue Engineering (TE) and it represents a step forward towards the substitutive or regenerative medicine. One of the major challenge of the TE is to design and develop, using a biomimetic approach, an artificial 3D anatomy scaffold, suitable for cells adhesion that are able to proliferate and differentiate themselves as consequence of the biological and biophysical stimulus offered by the specific tissue to be replaced. Nowadays, powerful instruments allow to perform analysis day by day more accurateand defined on patients that need more precise diagnosis and treatments.Starting from patient specific information provided by TC (Computed Tomography) microCT and MRI(Magnetic Resonance Imaging), an image-based approach can be performed in order to reconstruct the site to be replaced. With the aid of the recent Additive Manufacturing techniques that allow to print tridimensional objects with sub millimetric precision, it is now possible to practice an almost complete control of the parametrical characteristics of the scaffold: this is the way to achieve a correct cellular regeneration. In this work, we focalize the attention on a branch of TE known as Bone TE, whose the bone is main subject. Bone TE combines osteoconductive and morphological aspects of the scaffold, whose main properties are pore diameter, structure porosity and interconnectivity. The realization of the ideal values of these parameters represents the main goal of this work: here we'll a create simple and interactive biomimetic design process based on 3D CAD modeling and generative algorithmsthat provide a way to control the main properties and to create a structure morphologically similar to the cancellous bone. Two different typologies of scaffold will be compared: the first is based on Triply Periodic MinimalSurface (T.P.M.S.) whose basic crystalline geometries are nowadays used for Bone TE scaffolding; the second is based on using Voronoi's diagrams and they are more often used in the design of decorations and jewellery for their capacity to decompose and tasselate a volumetric space using an heterogeneous spatial distribution (often frequent in nature). In this work, we will show how to manipulate the main properties (pore diameter, structure porosity and interconnectivity) of the design TE oriented scaffolding using the implementation of generative algorithms: "bringing back the nature to the nature".

Contributo sperimentale alla ridefinizione della diffusione in parete della camera di prova della galleria del vento Dallara

Joseph Nicolas Cugnot built the first primitive car in 1769 and approximately one hundred year later the first automotive race took place. Thanks to this, for the first time the aerodynamics principles began to be applied to cars. The aerodynamic study of a car is important to improve the performance on the road, or on the track. It purposely enhances the stability in the turns and increases the maximum velocity. However, it is also useful, decrease the fuel consumption, in order to reduce the pollution. Given that cars are a very complex body, the aerodynamic study cannot be conducted following an analytical method, but it is possible, in general, to choose between two different approaches: the numerical or the experimental one. The results of numerical studies depend on the computers’ potential and on the method use to implement the mathematical model. Today, the best way to perform an aerodynamic study is still experimental, which means that in the first phase of the design process the study is performed in a wind tunnel and in later phases directly on track. The automotive wind tunnels are singular mainly due to the test chamber, which typically contains a ground simulation system. The test chamber can have different types of walls: open walls, closed walls, adaptive walls or slotted walls. The best solution is to use the slotted walls because they minimize the interference between the walls and the streamlines, the interaction between the flow and the environment, and also to contain the overall costs. Furthermore, is necessary minimize the boundary layer at the walls, without accelerating the flow, in order to provide the maximum section of homogeneous flow. This thesis aims at redefining the divergent angle of the Dallara Automobili S.P.A. wind tunnel’s walls, in order to improve the overall homogeneity. To perform this study it was necessary to acquire the pressure data of the boundary layer, than it was created the profile of the boundary layer velocity and, to minimize the experimental errors, it was calculated the displacement thickness. The results obtained shows, even if the instrument used to the experiment was not the best one, that the boundary layer thickness could be minor in case of a low diffusion angle. So it is convenient to perform another experiment with a most sensitive instrument to verified what is the better wall configuration.

Characterization of a 3D-printed low-cost flexible dielectric material for the realization of innovative WPT wearable applications

The aim of this thesis is to demonstrate that 3D-printing technologies can be considered significantly attractive in the production of microwave devices and in the antenna design, with the intention of making them lightweight, cheaper, and easily integrable for the production of wireless, battery-free, and wearable devices for vital signals monitoring. In this work, a new 3D-printable, low-cost resin material, the Flexible80A, is proposed as RF substrate in the implementation of a rectifying antenna (rectenna) operating at 2.45 GHz for wireless power transfer. A careful and accurate electromagnetic characterization of the abovementioned material, revealing it to be a very lossy substrate, has paved the way for the investigation of innovative transmission line and antenna layouts, as well as etching techniques, possible thanks to the design freedom enabled by 3D-printing technologies with the aim of improving the wave propagation performance within lossy materials. This analysis is crucial in the design process of a patch antenna, meant to be successively connected to the rectifier. In fact, many different patch antenna layouts are explored varying the antenna dimensions, the substrate etchings shape and position, the feeding line technology, and the operating frequency. Before dealing with the rectification stage of the rectenna design, the hot and long-discussed topic of the equivalent receiving antenna circuit representation is addressed, providing an overview of the interpretation of different authors about the issue, and the position that has been adopted in this thesis. Furthermore, two rectenna designs are proposed and simulated with the aim of minimizing the dielectric losses. Finally, a prototype of a rectenna with the antenna conjugate matched to the rectifier, operating at 2.45 GHz, has been fabricated with adhesive copper on a substrate sample of Flexible80A and measured, in order to validate the simulated results.

Multicelled Behaviour in E. coli: Design and experimental characterization of an engineered library of hybrid promoters.

Synthetic biology has recently had a great development, many papers have been published and many applications have been presented, spanning from the production of biopharmacheuticals to the synthesis of bioenergetic substrates or industrial catalysts. But, despite these advances, most of the applications are quite simple and don’t fully exploit the potential of this discipline. This limitation in complexity has many causes, like the incomplete characterization of some components, or the intrinsic variability of the biological systems, but one of the most important reasons is the incapability of the cell to sustain the additional metabolic burden introduced by a complex circuit. The objective of the project, of which this work is part, is trying to solve this problem through the engineering of a multicellular behaviour in prokaryotic cells. This system will introduce a cooperative behaviour that will allow to implement complex functionalities, that can’t be obtained with a single cell. In particular the goal is to implement the Leader Election, this procedure has been firstly devised in the field of distributed computing, to identify the process that allow to identify a single process as organizer and coordinator of a series of tasks assigned to the whole population. The election of the Leader greatly simplifies the computation providing a centralized control. Further- more this system may even be useful to evolutionary studies that aims to explain how complex organisms evolved from unicellular systems. The work presented here describes, in particular, the design and the experimental characterization of a component of the circuit that solves the Leader Election problem. This module, composed of an hybrid promoter and a gene, is activated in the non-leader cells after receiving the signal that a leader is present in the colony. The most important element, in this case, is the hybrid promoter, it has been realized in different versions, applying the heuristic rules stated in [22], and their activity has been experimentally tested. The objective of the experimental characterization was to test the response of the genetic circuit to the introduction, in the cellular environment, of particular molecules, inducers, that can be considered inputs of the system. The desired behaviour is similar to the one of a logic AND gate in which the exit, represented by the luminous signal produced by a fluorescent protein, is one only in presence of both inducers. The robustness and the stability of this behaviour have been tested by changing the concentration of the input signals and building dose response curves. From these data it is possible to conclude that the analysed constructs have an AND-like behaviour over a wide range of inducers’ concentrations, even if it is possible to identify many differences in the expression profiles of the different constructs. This variability accounts for the fact that the input and the output signals are continuous, and so their binary representation isn’t able to capture the complexity of the behaviour. The module of the circuit that has been considered in this analysis has a fundamental role in the realization of the intercellular communication system that is necessary for the cooperative behaviour to take place. For this reason, the second phase of the characterization has been focused on the analysis of the signal transmission. In particular, the interaction between this element and the one that is responsible for emitting the chemical signal has been tested. The desired behaviour is still similar to a logic AND, since, even in this case, the exit signal is determined by the hybrid promoter activity. The experimental results have demonstrated that the systems behave correctly, even if there is still a substantial variability between them. The dose response curves highlighted that stricter constrains on the inducers concentrations need to be imposed in order to obtain a clear separation between the two levels of expression. In the conclusive chapter the DNA sequences of the hybrid promoters are analysed, trying to identify the regulatory elements that are most important for the determination of the gene expression. Given the available data it wasn’t possible to draw definitive conclusions. In the end, few considerations on promoter engineering and complex circuits realization are presented. This section aims to briefly recall some of the problems outlined in the introduction and provide a few possible solutions.

Quantitative risk analysis as a tool in process design

La Quantitative Risk Analysis costituisce un valido strumento per la determinazione del rischio associato ad un’installazione industriale e per la successiva attuazione di piani di emergenza. Tuttavia, la sua applicazione nella progettazione di un lay-out richiede la scelta di un criterio in grado di valutare quale sia la disposizione ottimale al fine di minimizzare il rischio. In tal senso, le numerose procedure esistenti, sebbene efficaci, risultano piuttosto faticose e time-consuming. Nel presente lavoro viene dunque proposto un criterio semplice ed oggettivo per comparare i risultati di QRA applicate a differenti designs. Valutando l’area racchiusa nelle curve iso-rischio, vengono confrontate dapprima le metodologie esistenti per lo studio dell’effetto domino, e successivamente, viene applicata al caso di serbatoi in pressione una procedura integrata di Quantitative Risk Domino Assessment. I risultati ottenuti dimostrano chiaramente come sia possibile ridurre notevolmente il rischio di un’attività industriale agendo sulla disposizione delle apparecchiature, con l’obiettivo di limitare gli effetti di possibili scenari accidentali.

Modelli informativi per la valutazione BIM del livello di reversibilità e circolarità di componenti edilizi: il Design for Disassembly

La Tesi presenta un metodo per valutare il livello di reversibilità e circolarità dei componenti edili. Il concetto cardine dello studio è il Design for Disassembly (DfD), definibile come un approccio alla progettazione di organismi edilizi secondo criteri costruttivi volti a facilitare successivi cambiamenti e smantellamenti (completi o parziali), consentendo il riutilizzo dei componenti, al fine di ridurre l’impatto ambientale degli interventi. Attualmente, diverse ricerche in ambito scientifico si dedicano all’approfondimento di questa tematica, correlandola ad altri concetti come la metodologia del Building Information Modeling (BIM), che consente di digitalizzare il processo progettuale, la sua realizzazione e la sua gestione attraverso modelli. Dopo l’analisi dello stato dell’arte, il lavoro è giunto alla definizione di un insieme di parametri idonei per essere introdotti in un modello informativo, in grado di rappresentare la circolarità del componente in termini di DfD. Per ogni elemento del componente analizzato viene assegnato un valore numerico (variabile da 0,1 a 1) a ogni parametro. Tramite l’utilizzo di una formula elaborata nell’ambito di precedenti ricerche svolte dal Dipartimento di Architettura dell'Università di Bologna, opportunamente modificata, si ottiene un indice sintetico finale denominato “Express Building Circularity Indicators” (EBCI). Il metodo di analisi proposto come strumento a supporto del processo progettuale è stato validato tramite l’applicazione a diverse soluzioni di facciata per l’efficientamento energetico di un fabbricato selezionato come caso di studio italiano dal progetto Europeo Horizon 2020 "DRIVE 0 – Driving decarbonization of the EU building stock by enhancing a consumer centred and locally based circular renovation process". I risultati ottenuti hanno consentito di verificare la replicabilità del processo digitalizzato a diverse soluzioni costruttive e l’affidabilità del metodo di valutazione del grado di circolarità.