Assessing the effectiveness of ISO 3382 for evaluating the acoustical quality of italian historical theatres: the case study of the Bonci Theatre

The present study concerns the acoustical characterisation of Italian historical theatres. It moved from the ISO 3382 which provides the guidelines for the measurement of a well established set of room acoustic parameters inside performance spaces. Nevertheless, the peculiarity of Italian historical theatres needs a more specific approach. The Charter of Ferrara goes in this direction, aiming at qualifying the sound field in this kind of halls and the present work pursues the way forward. Trying to understand how the acoustical qualification should be done, the Bonci Theatre in Cesena has been taken as a case study. In September 2012 acoustical measurements were carried out in the theatre, recording monaural e binaural impulse responses at each seat in the hall. The values of the time criteria, energy criteria and psycho-acoustical and spatial criteria have been extracted according to ISO 3382. Statistics were performed and a 3D model of the theatre was realised and tuned. Statistical investigations were carried out on the whole set of measurement positions and on carefully chosen reduced subsets; it turned out that these subsets are representative only of the “average” acoustics of the hall. Normality tests were carried out to verify whether EDT, T30 and C80 could be described with some degree of reliability with a theoretical distribution. Different results, according to the varying assumptions underlying each test, were found. Finally, an attempt was made to correlate the numerical results emerged from the statistical analysis to the perceptual sphere. Looking for “acoustical equivalent areas”, relative difference limens were considered as threshold values. No rule of thumb emerged. Finally, the significance of the usual representation through mean values and standard deviation, which may be meaningful for normal distributed data, was investigated.

La strategia BIM a supporto del progetto della sicurezza nel cantiere edile: il caso dell'ospedale di primo soccorso a Lampedusa.

Throughout this research, the whole life cycle of a building will be analyzed, with a special focus on the most common issues that affect the construction sector nowadays, such as safety. In fact, the goal is to enhance the management of the entire construction process in order to reduce the risk of accidents. The contemporary trend is that of researching new tools capable of reducing, or even eliminating, the most common mistakes that usually lead to safety risks. That is one of the main reasons why new technologies and tools have been introduced in the field. The one we will focus on is the so-called BIM: Building Information Modeling. With the term BIM we refer to wider and more complex analysis tool than a simple 3D modeling software. Through BIM technologies we are able to generate a multi-dimension 3D model which contains all the information about the project. This innovative approach aims at a better understanding and control of the project by taking into consideration the entire life cycle and resulting in a faster and more sustainable way of management. Furthermore, BIM software allows for the sharing of all the information among the different aspects of the project and among the different participants involved thus improving the cooperation and communication. In addition, BIM software utilizes smart tools that simulate and visualize the process in advance, thus preventing issues that might not have been taking into consideration during the design process. This leads to higher chances of avoiding risks, delays and cost increases. Using a hospital case study, we will apply this approach for the completion of a safety plan, with a special focus onto the construction phase.

La generazione di modelli tridimensionali densi in ambito architettonico mediante la fotogrammetria digitale

The Italian territory offers a wide range of treasures in the field of Cultural Assets. This is a highly relevant property, which needs an accurate management and preservation performed by appropriate tools, also giving attention to the maintenance and safeguard from risk factors. Nowadays the increasing development of new digital technologies, added by remarkable steps forward got by the subject of Geomatic makes possible an efficient integration among different techniques, helped also by spread of solutions to improve the data import-export and transmission between different devices. The main objective of this thesis is to experience the photogrammetric restitution implemented in a commercial software of digital photogrammetry, in order to generate a dense 3D model of the facade of the Basilica Sant'Apollinare Nuovo in Ravenna. The 1st Chapter, after a general introduction regarding the 3D survey of Cultural Heritage and some considerations linked to the use of digital photogrammetry in this field, is focused to analyze the case of stereoscopic and the monoscopic approach. In particular, it develops the theme of close-range photogrammetry. The 2nd Chapter, exposes the theme of digital images, from color theory until their appearing on the monitor. The 3rd Chapter, develops the case study of the Basilica di Sant'Apollinare Nuovo, the historical, architectural and religious of the same. Also, it is examined the issue of photogrammetry and laser scanning of the case study. The final part of the same chapter, treats the processing of data processing the software Agisoft PhotoScan, in order to generate, by means of Structure from Motion technique, a digital geometric 3D model of the Basilica Facade. The digital model has been scaled on the basis of measurements made on the field. With the software it was possible to accomplish the three phases of the photogrammetric data processing: internal orientation, exterior orientation and restitution.

Study of a beam-column joint of a precast system by nonlinear numerical analysis

The present work consists of a detailed numerical analysis of a 4-way joint made of a precast column and two partially precast beams. The structure has been previously built and experimentally analyzed through a series of cyclic loads at the Laboratory of Tests on Structures (Laboratorio di Prove su Strutture, La. P. S.) of the University of Bologna. The aim of this work is to design a 3D model of the joint and then apply the techniques of nonlinear finite element analysis (FEA) to computationally reproduce the behavior of the structure under cyclic loads. Once the model has been calibrated to correctly emulate the joint, it is possible to obtain new insights useful to understand and explain the physical phenomena observed in the laboratory and to describe the properties of the structure, such as the cracking patterns, the force-displacement and the moment-curvature relations, as well as the deformations and displacements of the various elements composing the joint.

Tomographic 3D reconstruction through linear inversion for breast microwave imaging

In the present thesis we address the problem of detecting and localizing a small spherical target with characteristic electrical properties inside a volume of cylindrical shape, representing female breast, with MWI. One of the main works of this project is to properly extend the existing linear inversion algorithm from planar slice to volume reconstruction; results obtained, under the same conditions and experimental setup are reported for the two different approaches. Preliminar comparison and performance analysis of the reconstruction algorithms is performed via numerical simulations in a software-created environment: a single dipole antenna is used for illuminating the virtual breast phantom from different positions and, for each position, the corresponding scattered field value is registered. Collected data are then exploited in order to reconstruct the investigation domain, along with the scatterer position, in the form of image called pseudospectrum. During this process the tumor is modeled as a dielectric sphere of small radius and, for electromagnetic scattering purposes, it's treated as a point-like source. To improve the performance of reconstruction technique, we repeat the acquisition for a number of frequencies in a given range: the different pseudospectra, reconstructed from single frequency data, are incoherently combined with MUltiple SIgnal Classification (MUSIC) method which returns an overall enhanced image. We exploit multi-frequency approach to test the performance of 3D linear inversion reconstruction algorithm while varying the source position inside the phantom and the height of antenna plane. Analysis results and reconstructed images are then reported. Finally, we perform 3D reconstruction from experimental data gathered with the acquisition system in the microwave laboratory at DIFA, University of Bologna for a recently developed breast-phantom prototype; obtained pseudospectrum and performance analysis for the real model are reported.

Development of a polyplexes-based miRNA delivery system in a 3D-bioplotted osteoarthritis cellular model.

L'osteoartrite (OA) è una patologia infiammatorio/degenerativa ossea per la quale non sono disponibili terapie causali efficaci ma solo approcci palliativi per la riduzione del dolore cronico. E’ quindi giustificato un investimento per individuare nuove strategie di trattamento. In quest’ottica, lo scopo di questa tesi è stato quello di indagare l’efficacia di polyplexi a base di chitosano o di PEI-g-PEG in un modello cellulare 3D in vitro basato su un hydrogel di Gellan Gum Metacrilato (GGMA) con a bordo condrociti in condizioni simulate di OA. Inizialmente sono state studiate la dimensione e il potenziale-Z di un pool di formulazioni di poliplexi. Quindi se ne è valutata la citocompatibilità utilizzando cellule staminali mesenchimali immortalizzate Y201. Infine, una miscela di GGMA, cellule e polyplexi è stata utilizzata per la stampa 3D di campioni che sono stati coltivati fino a 14 giorni. La condizione OA è stata simulata trattando le cellule con una miscela di citochine implicate nello sviluppo della malattia. Tutte le formulazioni a base di chitosano e due basate su PEI-g-PEG si sono dimostrate citocompatibili e sono hanno veicolato i miRNA nelle cellule (come mostrato dai risultati di analisi in fluorescenza). I risultati delle colorazioni H&E e AlcianBlue hanno confermato che il terreno condizionato ha ben ricreato le condizioni di OA. I polyplexi a base di chitosano e PEI-g-PEG hanno controbilanciato gli effetti delle citochine. Risultati incoraggianti, anche se da approfondire ulteriormente, provengono anche dall’analisi di espressione (RT-PCR) di cinque geni specifici della cartilagine. Concludendo, questo modello ha ben riprodotto le condizioni di OA in vitro; il chitosano ha mostrato di essere un adeguato veicolo per un trattamento a base di miRNA; il PEI-g-PEG si propone come un'alternativa più economica e ragionevolmente affidabile, sebbene il rischio di citotossicità alle concentrazioni più elevate richieda una più esteva validazione sperimentale.

Optimized methods to digital survey and 3D modelling of cultural heritage assets

Currently making digital 3D models and replicas of the cultural heritage assets play an important role in the preservation and having a high detail source for future research and intervention. In this dissertation, it is tried to assess different methods for digital surveying and making 3D replicas of cultural heritage assets in different scales of size. The methodologies vary in devices, software, workflow, and the amount of skill that is required. The three phases of the 3D modelling process are data acquisition, modelling, and model presentation. Each of these sections is divided into sub-sections and there are several approaches, methods, devices, and software that may be employed, furthermore, the selection process should be based on the operation's goal, available facilities, the scale and properties of the object or structure to be modeled, as well as the operators' expertise and experience. The most key point to remember is that the 3D modelling operation should be properly accurate, precise, and reliable; therefore, there are so many instructions and pieces of advice on how to perform 3D modelling effectively. It is an attempt to compare and evaluate the various ways of each phase in order to explain and demonstrate their differences, benefits, and drawbacks in order to serve as a simple guide for new and/or inexperienced users.

From point cloud to HBIM: an integrated workflow for 3D reconstruction of heritage building with model accuracy evaluation

Modern society is now facing significant difficulties in attempting to preserve its architectural heritage. Numerous challenges arise consequently when it comes to documentation, preservation and restoration. Fortunately, new perspectives on architectural heritage are emerging owing to the rapid development of digitalization. Therefore, this presents new challenges for architects, restorers and specialists. Additionally, this has changed the way they approach the study of existing heritage, changing from conventional 2D drawings in response to the increasing requirement for 3D representations. Recently, Building Information Modelling for historic buildings (HBIM) has escalated as an emerging trend to interconnect geometrical and informational data. Currently, the latest 3D geomatics techniques based on 3D laser scanners with enhanced photogrammetry along with the continuous improvement in the BIM industry allow for an enhanced 3D digital reconstruction of historical and existing buildings. This research study aimed to develop an integrated workflow for the 3D digital reconstruction of heritage buildings starting from a point cloud. The Pieve of San Michele in Acerboli’s Church in Santarcangelo Di Romagna (6th century) served as the test bed. The point cloud was utilized as an essential referential to model the BIM geometry using Autodesk Revit® 2022. To validate the accuracy of the model, Deviation Analysis Method was employed using CloudCompare software to determine the degree of deviation between the HBIM model and the point cloud. The acquired findings showed a very promising outcome in the average distance between the HBIM model and the point cloud. The conducted approach in this study demonstrated the viability of producing a precise BIM geometry from point clouds.

Analisi FEM 3D d'interazione terreno-struttura: effetti dello scavo di una galleria sotto edifici in muratura

La presente tesi ha riguardato lo studio numerico con un modello 3D dell' interazione tra lo scavo di una galleria urbana e un edificio esistente in muratura, la Stazione di Ferrara Porta Reno (risalente ai primi del '900). A tale scopo è stato utilizzato il programma di calcolo agli elementi finiti Plaxis 3D. Nello studio numerico, per il terreno è stato adottato un modello costitutivo avanzato elasto-plastico con incrudimento isotropo, l’Hardening soil model with small strain stiffness, mentre per la muratura e stato utilizzato il criterio di Mohr-Coulomb. Inoltre, lo scavo della galleria è stato simulato con una procedura per passi, tenendo in conto i principali aspetti del processo. La subsidenza in superficie è stata controllata applicando una contrazione fittizia lungo lo scudo. E’ stata svolta un'analisi numerica in condizione di campo libero, ossia in assenza di strutture, al fine di valutare i movimenti del terreno indotti dal processo di scavo; successivamente sono state eseguite diverse analisi accoppiate, in condizioni di simmetria e con eccentricità della costruzione rispetto all'asse della galleria, per studiare il complesso fenomeno di interazione galleria-terreno-struttura. I risultati di tali analisi accoppiate sono stati utilizzati per effettuare una stima del livello di danno atteso per l'edificio. Le analisi numeriche condotte hanno messo in luce, confermando quanto già noto in letteratura, che la presenza di un edificio a piano campagna interagente con l’opera di scavo modifica la forma del profilo dei cedimenti relativa alle condizioni di campo libero. Tale modifica, che dipende dalle specifiche caratteristiche di rigidezza e peso della struttura presa in esame, generalmente si traduce in una riduzione del cedimento differenziale che può influenzare in modo significativo la stima del danno sull’edificio. Ciò è tanto più evidente, quanto maggiore è la perdita di volume indotta dallo scavo della galleria.

Development and application of a thermo-hydraulic model supporting the design and the deterministic safety analysis in a sodium cooled fast reactor

Il CP-ESFR è un progetto integrato di cooperazione europeo sui reattori a sodio SFR realizzato sotto il programma quadro EURATOM 7, che unisce il contributo di venticinque partner europei. Il CP-ESFR ha l'ambizione di contribuire all'istituzione di una "solida base scientifica e tecnica per il reattore veloce refrigerato a sodio, al fine di accelerare gli sviluppi pratici per la gestione sicura dei rifiuti radioattivi a lunga vita, per migliorare le prestazioni di sicurezza, l'efficienza delle risorse e il costo-efficacia di energia nucleare al fine di garantire un sistema solido e socialmente accettabile di protezione della popolazione e dell'ambiente contro gli effetti delle radiazioni ionizzanti. " La presente tesi di laurea è un contributo allo sviluppo di modelli e metodi, basati sull’uso di codici termo-idraulici di sistema, per l’ analisi di sicurezza di reattori di IV Generazione refrigerati a metallo liquido. L'attività è stata svolta nell'ambito del progetto FP-7 PELGRIMM ed in sinergia con l’Accordo di Programma MSE-ENEA(PAR-2013). Il progetto FP7 PELGRIMM ha come obbiettivo lo sviluppo di combustibili contenenti attinidi minori 1. attraverso lo studio di due diverse forme: pellet (oggetto della presente tesi) e spherepac 2. valutandone l’impatto sul progetto del reattore CP-ESFR. La tesi propone lo sviluppo di un modello termoidraulico di sistema dei circuiti primario e intermedio del reattore con il codice RELAP5-3D© (INL, US). Tale codice, qualificato per il licenziamento dei reattori nucleari ad acqua, è stato utilizzato per valutare come variano i parametri del core del reattore rilevanti per la sicurezza (es. temperatura di camicia e di centro combustibile, temperatura del fluido refrigerante, etc.), quando il combustibile venga impiegato per “bruciare” gli attinidi minori (isotopi radioattivi a lunga vita contenuti nelle scorie nucleari). Questo ha comportato, una fase di training sul codice, sui suoi modelli e sulle sue capacità. Successivamente, lo sviluppo della nodalizzazione dell’impianto CP-ESFR, la sua qualifica, e l’analisi dei risultati ottenuti al variare della configurazione del core, del bruciamento e del tipo di combustibile impiegato (i.e. diverso arricchimento di attinidi minori). Il testo è suddiviso in sei sezioni. La prima fornisce un’introduzione allo sviluppo tecnologico dei reattori veloci, evidenzia l’ambito in cui è stata svolta questa tesi e ne definisce obbiettivi e struttura. Nella seconda sezione, viene descritto l’impianto del CP-ESFR con attenzione alla configurazione del nocciolo e al sistema primario. La terza sezione introduce il codice di sistema termico-idraulico utilizzato per le analisi e il modello sviluppato per riprodurre l’impianto. Nella sezione quattro vengono descritti: i test e le verifiche effettuate per valutare le prestazioni del modello, la qualifica della nodalizzazione, i principali modelli e le correlazioni più rilevanti per la simulazione e le configurazioni del core considerate per l’analisi dei risultati. I risultati ottenuti relativamente ai parametri di sicurezza del nocciolo in condizioni di normale funzionamento e per un transitorio selezionato sono descritti nella quinta sezione. Infine, sono riportate le conclusioni dell’attività.

Compressed sensing in digital tomosynthesis reconstruction

In this work we study a model for the breast image reconstruction in Digital Tomosynthesis, that is a non-invasive and non-destructive method for the three-dimensional visualization of the inner structures of an object, in which the data acquisition includes measuring a limited number of low-dose two-dimensional projections of an object by moving a detector and an X-ray tube around the object within a limited angular range. The problem of reconstructing 3D images from the projections provided in the Digital Tomosynthesis is an ill-posed inverse problem, that leads to a minimization problem with an object function that contains a data fitting term and a regularization term. The contribution of this thesis is to use the techniques of the compressed sensing, in particular replacing the standard least squares problem of data fitting with the problem of minimizing the 1-norm of the residuals, and using as regularization term the Total Variation (TV). We tested two different algorithms: a new alternating minimization algorithm (ADM), and a version of the more standard scaled projected gradient algorithm (SGP) that involves the 1-norm. We perform some experiments and analyse the performance of the two methods comparing relative errors, iterations number, times and the qualities of the reconstructed images. In conclusion we noticed that the use of the 1-norm and the Total Variation are valid tools in the formulation of the minimization problem for the image reconstruction resulting from Digital Tomosynthesis and the new algorithm ADM has reached a relative error comparable to a version of the classic algorithm SGP and proved best in speed and in the early appearance of the structures representing the masses.

Energy harvesting from piezoelectric devices embedded in a 3D printed wing

This thesis work has been carried out at Clarkson University in Potsdam NY, USA and involved the design of a low elongation wing, consisting of parts made by polylactide (PLA) using the fused deposition model (FDM) technology of Rapid Prototyping, then assembled together in a thin aluminum spar. The aim of the research is to evaluate the feasibility of collecting electrical energy by converting mechanical energy from the vibration of the wing flutter. With this aim piezoelectric stripes were glued in the inner part of the wing, as well as on the aluminum spar, as monomorphic configuration. During the phases of the project, particular attention was given to the geometry and the materials used, in order to trigger the flutter for low flow velocity. The CAD software SolidWorks® was used for the design of the wing and then the drawings were sent to the Clarkson machine shop in order to to produce the parts required by the wing assembly. FEM simulations were performed, using software MSC NASTRAN/PATRAN®, to evaluate the stiffness of the whole wing as well as the natural vibration modes of the structure. These data, in a first approximation, were used to predict the flutter speed. Finally, experimental tests in the Clarkson wind tunnel facility were carried out in order to validate the results obtained from FEM analysis. The power collected by the piezoelectrics under flutter condition was addressed by tuning the resistors downstream the electronic circuit of the piezoelectrics.

Assimilation of data from conventional and non conventional networks through a LETKF scheme in the COSMO model

The present work studies a km-scale data assimilation scheme based on a LETKF developed for the COSMO model. The aim is to evaluate the impact of the assimilation of two different types of data: temperature, humidity, pressure and wind data from conventional networks (SYNOP, TEMP, AIREP reports) and 3d reflectivity from radar volume. A 3-hourly continuous assimilation cycle has been implemented over an Italian domain, based on a 20 member ensemble, with boundary conditions provided from ECMWF ENS. Three different experiments have been run for evaluating the performance of the assimilation on one week in October 2014 during which Genova flood and Parma flood took place: a control run of the data assimilation cycle with assimilation of data from conventional networks only, a second run in which the SPPT scheme is activated into the COSMO model, a third run in which also reflectivity volumes from meteorological radar are assimilated. Objective evaluation of the experiments has been carried out both on case studies and on the entire week: check of the analysis increments, computing the Desroziers statistics for SYNOP, TEMP, AIREP and RADAR, over the Italian domain, verification of the analyses against data not assimilated (temperature at the lowest model level objectively verified against SYNOP data), and objective verification of the deterministic forecasts initialised with the KENDA analyses for each of the three experiments.

Integration of robotic inverse kinematic routines in an algorithmic 3D modeling software

An industrial manipulator equipped with an automatic clay extruder is used to realize a machine that can manufacture additively clay objects. The desired geometries are designed by means of a 3D modeling software and then sliced in a sequence of layers with the same thickness of the extruded clay section. The profiles of each layer are transformed in trajectories for the extruder and therefore for the end-effector of the manipulator. The goal of this thesis is to improve the algorithm for the inverse kinematic resolution and the integration of the routine within the development software that controls the machine (Rhino/Grasshopper). The kinematic model is described by homogeneous transformations, adopting the Denavit-Hartenberg standard convention. The function is implemented in C# and it has been preliminarily tested in Matlab. The outcome of this work is a substantial reduction of the computation time relative to the execution of the algorithm, which is halved.

Economic and Environmental Optimization of Ornamental Stone Block Cutting with a 3D Algorithm

This thesis focuses on finding the optimum block cutting dimensions in terms of the environmental and economic factors by using a 3D algorithm for a limestone quarry in Foggia, Italy. The environmental concerns of quarrying operations are mainly: energy consumption, material waste, and pollution. The main economic concerns are the block recovery, the selling prices, and the production costs. Fractures adversely affect the block recovery ratio. With a fracture model, block production can be optimized. In this research, the waste volume produced by quarrying was minimised to increase the recovery ratio and ensure economic benefits. SlabCutOpt is a software developed at DICAM–University of Bologna for block cutting optimization which tests different cutting angles on the x-y-z planes to offer up alternative cutting methods. The program tests several block sizes and outputs the optimal result for each entry. By using SlabCutOpt, ten different block dimensions were analysed, the results indicated the maximum number of non-intersecting blocks for each dimension. After analysing the outputs, the block named number 1 with the dimensions ‘1mx1mx1m’ had the highest recovery ratio as 43% and the total Relative Money Value (RMV) with a value of 22829. Dimension number 1, also had the lowest waste volume, with a value of 3953.25 m3, for the total bench. For cutting the total bench volume of 6932.25m3, the diamond wire cutter had the lowest dust emission values for the block with the dimension ‘2mx2mx2m’, with a value of 24m3. When compared with the Eco-Label standards, block dimensions having surface area values lower than 15m2, were found to fit the natural resource waste criteria of the label, as the threshold required 25% of minimum recovery [1]. Due to the relativity of production costs, together with the Eco-Label threshold, the research recommends the selection of the blocks with a surface area value between 6m2 and 14m2.